Atomic-Scale Mechanisms of MoS2 Oxidation for Kinetic Control of MoS2/MoO3 Interfaces.

Oxidation of transition metal dichalcogenides (TMDs) occurs readily under a variety of conditions. Therefore, understanding the oxidation processes is necessary for successful TMD handling and device fabrication. Here, we investigate atomic-scale oxidation mechanisms of the most widely studied TMD, MoS2. We find that thermal oxidation results in α-phase crystalline MoO3 with sharp interfaces, voids, and crystallographic alignment with the underlying MoS2. Experiments with remote substrates prove that thermal oxidation proceeds via vapor-phase mass transport and redeposition, a challenge to forming thin, conformal films. Oxygen plasma accelerates the kinetics of oxidation relative to the kinetics of mass transport, forming smooth and conformal oxides. The resulting amorphous MoO3 can be grown with subnanometer to several-nanometer thickness, and we calibrate the oxidation rate for different instruments and process parameters. Our results provide quantitative guidance for managing both the atomic scale structure and thin-film morphology of oxides in the design and processing of TMD devices.

Direct Visualization of Subnanometer Variations in the Excitonic Spectra of 2D/3D Semiconductor/Metal Heterostructures.

The integration of metallic contacts with two-dimensional (2D) semiconductors is routinely required for the fabrication of nanoscale devices. However, nanometer-scale variations in the 2D/metal interface can drastically alter the local optoelectronic properties. Here, we map local excitonic changes of the 2D semiconductor MoS2 in contact with Au. We utilize a suspended and epitaxially grown 2D/metal platform that allows correlated electron energy-loss spectroscopy (EELS) and angle resolved photoelectron spectroscopy (nanoARPES) mapping. Spatial localization of MoS2 excitons uncovers an additional EELS peak related to the MoS2/Au interface. NanoARPES measurements indicate that Au-S hybridization decreases substantially with distance from the 2D/metal interface, suggesting that the observed EELS peak arises due to dielectric screening of the excitonic Coulomb interaction. Our results suggest that increasing the van der Waals distance could optimize excitonic spectra of mixed-dimensional 2D/3D interfaces and highlight opportunities for Coulomb engineering of exciton energies by the local dielectric environment or moiré engineering.

Mechanisms of Quasi van der Waals Epitaxy of Three-Dimensional Metallic Nanoislands on Suspended Two-Dimensional Materials.

Understanding structure at the interface between two-dimensional (2D) materials and 3D metals is crucial for designing novel 2D/3D heterostructures and improving the performance of many 2D material devices. Here, we quantify and discuss the 2D/3D interface structure and the 3D morphology in several materials systems. We first deposit faceted Au nanoislands on graphene and transition metal dichalcogenides, using measurements of the equilibrium island shape to determine values for the 2D/Au interface energy and examining the role of surface reconstructions, chemical identity, and defects on the grown structures. We then deposit the technologically relevant metals Ti and Nb under conditions where kinetic rather than thermodynamic factors govern growth. We describe a transition from dendritic to faceted islands as a function of growth temperature and discuss the factors determining island shape in these materials systems. Finally, we show that suspended 2D materials enable the fabrication of a novel type of 3D/2D/3D heterostructure and discuss the growth mechanism. We suggest that emerging nanodevices will utilize versatile fabrication of 2D/3D heterostructures with well-characterized interfaces and morphologies.

Interface dynamics and crystal phase switching in GaAs nanowires.

Controlled formation of non-equilibrium crystal structures is one of the most important challenges in crystal growth. Catalytically grown nanowires are ideal systems for studying the fundamental physics of phase selection, and could lead to new electronic applications based on the engineering of crystal phases. Here we image gallium arsenide (GaAs) nanowires during growth as they switch between phases as a result of varying growth conditions. We find clear differences between the growth dynamics of the phases, including differences in interface morphology, step flow and catalyst geometry. We explain these differences, and the phase selection, using a model that relates the catalyst volume, the contact angle at the trijunction (the point at which solid, liquid and vapour meet) and the nucleation site of each new layer of GaAs. This model allows us to predict the conditions under which each phase should be observed, and use these predictions to design GaAs heterostructures. These results could apply to phase selection in other nanowire systems.

One-dimensional twisted and tubular structures of zinc oxide by semiconductor-catalyzed vapor-liquid-solid synthesis.

The exploration of unconventional catalysts for the vapor-liquid-solid synthesis of one-dimensional materials promises to yield new morphologies and functionality. Here, we show, for the model ZnO system, that unusual nanostructures can be produced via a semiconductor (Ge) catalyst. As well as the usual straight nanowires, we describe two other distinct morphologies: twisted nanowires and twisted nanotubes. The twisted nanotubes show large hollow cores and surprisingly high twisting rates, up to 9°/µm, that cannot be easily explained through the Eshelby twist model. A combination of ex situ and in situ transmission electron microscopy measurements suggest that the hollow core results from a competition between growth and etching at the Ge-ZnO interface during synthesis. The twisting rate is consistent with a softening of elastic rigidity. These results indicate that the use of unconventional, nonmetallic catalysts provides opportunities to synthesize unusual oxide nanostructures with potentially useful properties.

In situ TEM modification of individual silicon nanowires and their charge transport mechanisms.

Correlating the structure and composition of nanowires grown by the vapour-liquid-solid (VLS) mechanism with their electrical properties is essential for designing nanowire devices. In situ transmission electron microscopy (TEM) that can image while simultaneously measuring the current-voltage (I-V) characteristics of individual isolated nanowires is a unique tool for linking changes in structure with electronic transport. Here we grow and electrically connect silicon nanowires inside a TEM to perform in situ electrical measurements on individual nanowires both at high temperature and upon surface oxidation, as well as under ambient conditions. As-grown, the oxide-free nanowires have nonlinear I-V characteristics. We analyse the I-V measurements in terms of both bulk and injection limited transport models, finding Joule heating effects, bulk-limiting effects for thin nanowires and an injection-limiting effect for thick wires when high voltages are applied. When the nanowire surface is modified by in situ oxidation, drastic changes occur in the electronic properties. We investigate the relation between the observed geometry, changes in the surface structure and changes in electronic transport, obtaining information for individual nanowires that is inaccessible to other measuring techniques.

Unveiling the carrier transport mechanism in epitaxial graphene for forming wafer-scale, single-domain graphene.

Graphene epitaxy on the Si face of a SiC wafer offers monolayer graphene with unique crystal orientation at the wafer-scale. However, due to carrier scattering near vicinal steps and excess bilayer stripes, the size of electrically uniform domains is limited to the width of the terraces extending up to a few microns. Nevertheless, the origin of carrier scattering at the SiC vicinal steps has not been clarified so far. A layer-resolved graphene transfer (LRGT) technique enables exfoliation of the epitaxial graphene formed on SiC wafers and transfer to flat Si wafers, which prepares crystallographically single-crystalline monolayer graphene. Because the LRGT flattens the deformed graphene at the terrace edges and permits an access to the graphene formed at the side wall of vicinal steps, components that affect the mobility of graphene formed near the vicinal steps of SiC could be individually investigated. Here, we reveal that the graphene formed at the side walls of step edges is pristine, and scattering near the steps is mainly attributed by the deformation of graphene at step edges of vicinalized SiC while partially from stripes of bilayer graphene. This study suggests that the two-step LRGT can prepare electrically single-domain graphene at the wafer-scale by removing the major possible sources of electrical degradation.

Control of Growth Front Evolution by Bi Additives during ZnAu Electrodeposition.

The performance of many electrochemical energy storage systems can be compromised by the formation of metal dendrites during charging. Additives in the electrolyte represent a useful strategy to mitigate dendrite formation, but understanding the mechanisms involved requires knowledge of the nanoscale effects of additives during electrochemical deposition. Here we quantify the effects of an inorganic additive on the morphology of an evolving electrochemical growth front, using liquid cell electron microscopy to provide the necessary spatial and temporal resolution. We examine deposition of ZnAu on Au in the presence of Bi additive, and show that low concentrations of Bi delay but do not prevent the formation of growth front instabilities. We describe a model in which Bi segregates at the growth front and promotes the surface diffusion and relaxation of Zn, allowing better coverage of the initial Au electrode surface. A more precise knowledge of the mechanism of inorganic additive effects may help in designing electrolyte chemistry for battery and other applications where morphology control is essential.

Dynamics of Nanoscale Dendrite Formation in Solution Growth Revealed Through in Situ Liquid Cell Electron Microscopy.

Formation mechanisms of dendrite structures have been extensively explored theoretically, and many theoretical predictions have been validated for micro- or macroscale dendrites. However, it is challenging to determine whether classical dendrite growth theories are applicable at the nanoscale due to the lack of detailed information on the nanodendrite growth dynamics. Here, we study iron oxide nanodendrite formation using liquid cell transmission electron microscopy (TEM). We observe "seaweed"-like iron oxide nanodendrites growing predominantly in two dimensions on the membrane of a liquid cell. By tracking the trajectories of their morphology development with high spatial and temporal resolution, it is possible to explore the relationship between the tip curvature and growth rate, tip splitting mechanisms, and the effects of precursor diffusion and depletion on the morphology evolution. We show that the growth of iron oxide nanodendrites is remarkably consistent with the existing theoretical predictions on dendritic morphology evolution during growth, despite occurring at the nanoscale.

Stability of Schottky and Ohmic Au Nanocatalysts to ZnO Nanowires.

Manufacturable nanodevices must now be the predominant goal of nanotechnological research to ensure the enhanced properties of nanomaterials can be fully exploited and fulfill the promise that fundamental science has exposed. Here, we test the electrical stability of Au nanocatalyst-ZnO nanowire contacts to determine the limits of the electrical transport properties and the metal-semiconductor interfaces. While the transport properties of as-grown Au nanocatalyst contacts to ZnO nanowires have been well-defined, the stability of the interfaces over lengthy time periods and the electrical limits of the ohmic or Schottky function have not been studied. In this work, we use a recently developed iterative analytical process that directly correlates multiprobe transport measurements with subsequent aberration-corrected scanning transmission electron microscopy to study the electrical, structural, and chemical properties when the nanowires are pushed to their electrical limits and show structural changes occur at the metal-nanowire interface or at the nanowire midshaft. The ohmic contacts exhibit enhanced quantum-mechanical edge-tunneling transport behavior because of additional native semiconductor material at the contact edge due to a strong metal-support interaction. The low-resistance nature of the ohmic contacts leads to catastrophic breakdown at the middle of the nanowire span where the maximum heating effect occurs. Schottky-type Au-nanowire contacts are observed when the nanowires are in the as-grown pristine state and display entirely different breakdown characteristics. The higher-resistance rectifying I-V behavior degrades as the current is increased which leads to a permanent weakening of the rectifying effect and atomic-scale structural changes at the edge of the Au interface where the tunneling current is concentrated. Furthermore, to study modified nanowires such as might be used in devices the nanoscale tunneling path at the interface edge of the ohmic nanowire contacts is removed with a simple etch treatment and the nanowires show similar I-V characteristics during breakdown as the Schottky pristine contacts. Breakdown is shown to occur either at the nanowire midshaft or at the Au contact depending on the initial conductivity of the Au contact interface. These results demonstrate the Au-nanowire structures are capable of withstanding long periods of electrical stress and are stable at high current densities ensuring they are ideal components for nanowire-device designs while providing the flexibility of choosing the electrical transport properties which other Au-nanowire systems cannot presently deliver.

Creating New VLS Silicon Nanowire Contact Geometries by Controlling Catalyst Migration.

The formation of self-assembled contacts between vapor-liquid-solid grown silicon nanowires and flat silicon surfaces was imaged in situ using electron microscopy. By measuring the structural evolution of the contact formation process, we demonstrate how different contact geometries are created by adjusting the balance between silicon deposition and Au migration. We show that electromigration provides an efficient way of controlling the contact. The results point to novel device geometries achieved by direct nanowire growth on devices.

Strain and stability of ultrathin Ge layers in Si/Ge/Si axial heterojunction nanowires.

The formation of abrupt Si/Ge heterointerfaces in nanowires presents useful possibilities for bandgap engineering. We grow Si nanowires containing thick Ge layers and sub-1 nm thick Ge "quantum wells" and measure the interfacial strain fields using geometric phase analysis. Narrow Ge layers show radial compressive strains of several percent, while stress at the Si/Ge interface causes lattice rotation. High strains can be achieved in these heterostructures, but we show that they are unstable to interdiffusion.

Control of Electron Beam-Induced Au Nanocrystal Growth Kinetics through Solution Chemistry.

Measurements of solution-phase crystal growth provide mechanistic information that is helpful in designing and synthesizing nanostructures. Here, we examine the model system of individual Au nanocrystal formation within a defined liquid geometry during electron beam irradiation of gold chloride solution, where radiolytically formed hydrated electrons reduce Au ions to solid Au. By selecting conditions that favor the growth of well-faceted Au nanoprisms, we measure growth rates of individual crystals. The volume of each crystal increases linearly with irradiation time at a rate unaffected by its shape or proximity to neighboring crystals, implying a growth process that is controlled by the arrival of atoms from solution. Furthermore, growth requires a threshold dose rate, suggesting competition between reduction and oxidation processes in the solution. Above this threshold, the growth rate follows a power law with dose rate. To explain the observed dose rate dependence, we demonstrate that a reaction-diffusion model is required that explicitly accounts for the species H(+) and Cl(-). The model highlights the necessity of considering all species present when interpreting kinetic data obtained from beam-induced processes, and suggest conditions under which growth rates can be controlled with higher precision.

Bubble and pattern formation in liquid induced by an electron beam.

Liquid cell electron microscopy has emerged as a powerful technique for in situ studies of nanoscale processes in liquids. An accurate understanding of the interactions between the electron beam and the liquid medium is essential to account for, suppress, and exploit beam effects. We quantify the interactions of high energy electrons with water, finding that radiolysis plays an important role, while heating is typically insignificant. For typical imaging conditions, we find that radiolysis products such as hydrogen and hydrated electrons achieve equilibrium concentrations within seconds. At sufficiently high dose-rate, the gaseous products form bubbles. We image bubble nucleation, growth, and migration. We develop a simplified reaction-diffusion model for the temporally and spatially varying concentrations of radiolysis species and predict the conditions for bubble formation by H2. We discuss the conditions under which hydrated electrons cause precipitation of cations from solution and show that the electron beam can be used to "write" structures directly, such as nanowires and other complex patterns, without the need for a mask.

Metastable structures in Al thin films before the onset of corrosion pitting as observed using liquid cell transmission electron microscopy.

One of the fundamental challenges in understanding the early stages of corrosion pitting in metals protected with an oxide film is that there are relatively few techniques that can probe microstructure with sufficient resolution while maintaining a wet environment. Here, we demonstrate that microstructural changes in Al thin films caused by aqueous NaCl solutions of varying chloride concentrations can be directly observed using a liquid flow cell enclosed within a transmission electron microscope (TEM) holder. In the absence of chloride, Al thin films did not exhibit significant corrosion when immersed in de-ionized water for 2 days. However, introducing 0.01 M NaCl solutions led to extensive random formation of blisters over the sample surface, while 0.1 M NaCl solutions formed anomalous structures that were larger than the typical grain size. Immersion in 1.0 M NaCl solutions led to fractal corrosion consistent with previously reported studies of Al thin films using optical microscopy. These results show the potential of in situ liquid cell electron microscopy for probing the processes that take place before the onset of pitting and for correlating pit locations with the underlying microstructure of the material.

Strategies to control morphology in hybrid group III-V/group IV heterostructure nanowires.

By combining in situ and ex situ transmission electron microscopy measurements, we examine the factors that control the morphology of "hybrid" nanowires that include group III-V and group IV materials. We focus on one materials pair, GaP/Si, for which we use a wide range of growth parameters. We show through video imaging that nanowire morphology depends on growth conditions, but that a general pattern emerges where either single kinks or inclined defects form some distance after the heterointerface. We show that pure Si nanowires can be made to exhibit the same kinks and defects by changing their droplet volume. From this we derive a model where droplet geometry drives growth morphology and discuss optimization strategies. We finally discuss morphology control for material pairs where the second material kinks immediately at the heterointerface and show that an interlayer between segments can enable the growth of unkinked hybrid nanowires.

Controlled formation of three-dimensional cavities during lateral epitaxial growth.

Epitaxial growth is a fundamental step required to create devices for the semiconductor industry, enabling different materials to be combined in layers with precise control of strain and defect structure. Patterning the growth substrate with a mask before performing epitaxial growth offers additional degrees of freedom to engineer the structure and hence function of the semiconductor device. Here, we demonstrate that conditions exist where such epitaxial lateral overgrowth can produce complex, three-dimensional structures that incorporate cavities of deterministic size. We grow germanium on silicon substrates patterned with a dielectric mask and show that fully-enclosed cavities can be created through an unexpected self-assembly process that is controlled by surface diffusion and surface energy minimization. The result is confined cavities enclosed by single crystalline Ge, with size and position tunable through the initial mask pattern. We present a model to account for the observed cavity symmetry, pinch-off and subsequent evolution, reflecting the dominant role of surface energy. Since dielectric mask patterning and epitaxial growth are compatible with conventional device processing steps, we suggest that this mechanism provides a strategy for developing electronic and photonic functionalities.

Salt-Assisted Vapor-Liquid-Solid Growth of 1D van der Waals Materials.

The method of salt-assisted vapor-liquid-solid (VLS) growth is introduced to synthesize 1D nanostructures of trichalcogenide van der Waals (vdW) materials, exemplified by niobium trisulfide (NbS3). The method uses a unique catalyst consisting of an alloy of Au and an alkali metal halide (NaCl) to enable rapid and directional growth. High yields of two types of NbS3 1D nanostructures, nanowires and nanoribbons, each with sub-ten nanometer diameter, tens of micrometers length, and distinct 1D morphology and growth orientation are demonstrated. Strategies to control the location, size, and morphology of growth, and extend the growth method to synthesize other transition metal trichalcogenides, NbSe3 and TiS3, as nanowires are demonstrated. Finally, the role of the Au-NaCl alloy catalyst in guiding VLS synthesis is described and the growth mechanism based on the relationships measured between structure (growth orientation, morphology, and dimensions) and growth conditions (catalyst volume and growth time) is discussed. These results introduce opportunities to expand the library of emerging 1D vdW materials to make use of their unique properties through controlled growth at nanoscale dimensions.

Electrochemical Intercalation and Exfoliation of CrSBr into Ferromagnetic Fibers and Nanoribbons.

Recent studies dedicated to layered van der Waals crystals have attracted significant attention to magnetic atomically thin crystals offering unprecedented opportunities for applications in innovative magnetoelectric, magneto-optic, and spintronic devices. The active search for original platforms for the low-dimensional magnetism study has emphasized the entirely new magnetic properties of two dimensional (2D) semiconductor CrSBr. Herein, for the first time, the electrochemical exfoliation of bulk CrSBr in a non-aqueous environment is demonstrated. Notably, crystal cleavage governed by the structural anisotropy occurred along two directions forming atomically thin and few-layered nanoribbons. The exfoliated material possesses an orthorhombic crystalline structure and strong optical anisotropy, showing the polarization dependencies of Raman signals. The antiferromagnetism exhibited by multilayered CrSBr gives precedence to ferromagnetic ordering in the revealed CrSBr nanostructures. Furthermore, the potential application of CrSBr nanoribbons is pioneered for electrochemical photodetector fabrication and demonstrates its responsivity up to 30 µA cm-2 in the visible spectrum. Moreover, the CrSBr-based anode for lithium-ion batteries exhibited high performance and self-improving abilities. This anticipates that the results will pave the way toward the future study of CrSBr and practical applications in magneto- and optoelectronics.