Optimized Phase and Crystallinity of Cr2(NCN)3 Dominating Electrochemical Lithium Storage Performance.

Cr2(NCN)3 is a potentially high-capacity and fast-charge Li-ion anode owing to its abundant and broad tunnels. However, high intrinsic chemical instability severely restricts its capacity output and electrochemical reversibility. Herein we report an effective crystalline engineering method for optimizing its phase and crystallinity. Systematic studies reveal the relevancy between electrochemical performance and crystalline structure; an optimal Cr2(NCN)3 with high phase purity and uniform crystallinity exhibits a high reversible capacity of 590 mAh g-1 and a stable cycling performance of 478 mAh g-1 after 500 cycles. In-operando heating XRD reveals its high thermodynamical stability over 600 °C, and in-operando electrochemical XRD proves its electrochemical Li storage mechanism, consisting of the primary Li-ion intercalation and subsequent conversion reactions. This study introduces a facile and low-cost method for fabricating high-purity Cr2(NCN)3, and it also confirms that the Li storage of Cr2(NCN)3 can be further improved by tuning its phase and crystallinity.

Double-Salts Super Concentrated Carbonate Electrolyte Boosting Electrochemical Performance of Ni-Rich LiNi0.90Co0.05Mn0.05O2 Lithium Metal Batteries.

Current lithium-ion batteries cannot meet the requirement of higher energy density with further large-scale application of electrical vehicles. Lithium metal batteries combined with Ni-rich layered oxides cathode are expected as the one of promising solutions, while the poor electrode and electrolyte interface impedes the commercial development of lithium metal batteries. A new double-salts super concentrated (DSSC) carbonate electrolyte is proposed to improve the electrochemical performance of LiNi0.90Co0.05Mn0.05O2 (NCM9055)||Li metal battery which exhibits stable cycling performance with the capacity retention of 93.04% and reversible capacity of 173.8 mAh g-1 after 100 cycles at 1 C, while cells with conventional 1 m diluted electrolyte remains only 60.55% and capacity of 114.2 mAh g-1. The double salts synergistic effect in super concentrated electrolyte promotes the formation for more balanced stable cathode electrolyte interface (CEI) inorganic compounds of CFx, LiNOx, SOF2, Li2SO4, and less LiF by X-ray photoelectron spectroscopy (XPS) test, and the uniform 2-3 nm rock-salt phase protection layer on the cathode surface by transmission electron microscope (TEM) characterization, improving the cycling performance of the Ni-rich NCM9055 layered oxide cathode. The DSSC electrolyte also can relief the Li dendrite growth on Li metal anode, as well as exhibit better flame retardance, promoting the application of more safety Ni-rich NCM9055||Li metal batteries.

Spherical Shell with CNTs Network Structuring Fe-Based Alluaudite Na2+2 δ Fe2- δ (SO4 )3 Cathode and Novel Phase Transition Mechanism for Sodium-Ion Battery.

Iron-based sulfate cathodes of alluaudite Na2+2 δ Fe2- δ (SO4 )3 (NFS) in sodium-ion batteries with low cost, steady cycling performance, and high voltage are promising for grid-scale energy storage systems. However, the poor electronic conductivity and the limited understanding of the phase-evolution of precursors hinder obtaining high-rate capacity and the pure phase. Distinctive NFS@C@n%CNTs (n = 1, 2, 5, 10) sphere-shell conductive networks composite cathode materials are constructed creatively, which exhibit superior reversible capacity and rate performance. In detail, the designed NFS@C@2%CNTs cathode delivers an initial discharge capacity of 95.9 mAh g-1 at 0.05 C and up to 60 mAh g-1 at a high rate of 10 C. The full NFS@C@2%CNTs//HC cell delivers a practical operating voltage of 3.5 V and mass-energy density of 140 Wh kg-1 at 0.1 C, and it can also retain 67.37 mAh g-1 with a capacity retention rate of 96.4% after 200 cycles at 2 C. On the other hand, a novel combination reaction mechanism is first revealed for forming NFS from the mixtures of Na2 Fe(SO4 )2 ·nH2 O (n = 2, 4) and FeSO4 ·H2 O during the sintering process. The inspiring results would provide a novel perspective to synthesize high-performance alluaudite sulfate and analogs by aqueous methods.

P2-Type Moisture-Stable and High-Voltage-Tolerable Cathodes for High-Energy and Long-Life Sodium-Ion Batteries.

P2-Na0.67Ni0.33Mn0.67O2 represents a promising cathode for Na-ion batteries, but it suffers from severe structural degradation upon storing in a humid atmosphere and cycling at a high cutoff voltage. Here we propose an in situ construction to achieve simultaneous material synthesis and Mg/Sn cosubstitution of Na0.67Ni0.33Mn0.67O2 via one-pot solid-state sintering. The materials exhibit superior structural reversibility and moisture insensitivity. In-operando XRD reveals an essential correlation between cycling stability and phase reversibility, whereas Mg substitution suppressed the P2-O2 phase transition by forming a new Z phase, and Mg/Sn cosubstitution enhanced the P2-Z transition reversibility benefiting from strong Sn-O bonds. DFT calculations disclosed high chemical tolerance to moisture, as the adsorption energy to H2O was lower than that of the pure Na0.67Ni0.33Mn0.67O2. A representative Na0.67Ni0.23Mg0.1Mn0.65Sn0.02O2 cathode exhibits high reversible capacities of 123 mAh g-1 (10 mA g-1), 110 mAh g-1 (200 mA g-1), and 100 mAh g-1 (500 mA g-1) and a high capacity retention of 80% (500 mA g-1, 500 cycles).

Benchmarking the Effect of Particle Size on Silicon Anode Materials for Lithium-Ion Batteries.

High-capacity silicon has been regarded as one of the most promising anodes for high-energy lithium-ion batteries. However, it suffers from severe volume expansion, particle pulverization, and repeated solid electrolyte interphase (SEI) growth, which leads to rapid electrochemical failure, while the particle size also plays key role here and its effects remain elusive. In this paper, through multiple-physical, chemical, and synchrotron-based characterizations, the evolutions of the composition, structure, morphology, and surface chemistry of silicon anodes with the particle size ranging from 50 to 5 µm upon cycling are benchmarked, which greatly link to their electrochemical failure discrepancies. It is found that the nano- and micro-silicon anodes undergo similar crystal to amorphous phase transition, but quite different composition transition upon de-/lithiation; at the same time, the nano- and 1 µm-silicon samples present obviously different mechanochemical behaviors from the 5 µm-silicon sample, such as electrode crack, particle pulverization/crack as well as volume expansion; in addition, the micro-silicon samples possess much thinner SEI layer than the nano-silicon samples upon cycling, and also differences in SEI compositions. It is hoped this comprehensive study and understanding should offer critical insights into the exclusive and customized modification strategies to diverse silicon anodes ranging from nano to microscale.

Thermochemical Cyclization Constructs Bridged Dual-Coating of Ni-Rich Layered Oxide Cathodes for High-Energy Li-Ion Batteries.

Enhancing microstructural and electrochemical stabilities of Ni-rich layered oxides is critical for improving the safety and cycle-life of high-energy Li-ion batteries. Here we propose a thermochemical cyclization strategy where heating polyacrylonitrile with LiNi0.8Co0.1Mn0.1O2 can simultaneously construct a cyclized polyacrylonitrile outer layer and a rock-salt bridge-like inner layer, forming a compact dual-coating of LiNi0.8Co0.1Mn0.1O2. Systematic studies demonstrate that the mild cyclization reaction between polyacrylonitrile and LiNi0.8Co0.1Mn0.1O2 induces a desirable "layered to rock-salt" structural transformation to create a nano-intermedium that acts as the bridge for binding cyclized polyacrylonitrile to layered LiNi0.8Co0.1Mn0.1O2. Because of the improvement of the structural and electrochemical stability and electrical properties, this cathode design remarkably enhances the cycling performance and rate capability of LiNi0.8Co0.1Mn0.1O2, showing a high reversible capacity of 183 mAh g-1 and a high capacity retention of 83% after 300 cycles at 1 C rate. Notably, this facile and scalable surface engineering makes Ni-rich cathodes potentially viable for commercialization in high-energy Li-ion batteries.

Quantifying the Contribution of the Dispersion Interaction and Hydrogen Bonding to the Anisotropic Elastic Properties of Chitin and Chitosan.

The elastic tensors of chitin and chitosan allomorphs were calculated using density functional theory (DFT) with and without the dispersion correction and compared with experimental values. The longitudinal Young's moduli were 114.9 or 126.9 GPa for α-chitin depending on the hydrogen bond pattern: 129.0 GPa for ß-chitin and 191.5 GPa for chitosan. Furthermore, the moduli were found to vary between 17.0 and 52.8 GPa in the transverse directions and between 2.2 and 15.2 GPa in shear. Switching off the dispersion correction led to a decrease in modulus by up to 63%, depending on the direction. The transverse Young's moduli of α-chitin strongly depended on the hydroxylmethyl group conformation coupled with the dispersion correction, suggesting a synergy between hydrogen bonding and dispersion interactions. The calculated longitudinal Young's moduli were, in general, higher than experimental values obtained in static conditions, and the Poisson's ratios were lower than experimental values obtained in static conditions.

Crystal Phase-Controlled Modulation of Binary Transition Metal Oxides for Highly Reversible Li-O2 Batteries.

Reducing charge-discharge overpotential of transition metal oxide catalysts can eventually enhance the cell efficiency and cycle life of Li-O2 batteries. Here, we propose that crystal phase engineering of transition metal oxides could be an effective way to achieve the above purpose. We establish controllable crystal phase modulation of the binary MnxCo1-xO by adopting a cation regulation strategy. Systematic studies reveal an unprecedented relevancy between charge overpotential and crystal phase of MnxCo1-xO catalysts, whereas a dramatically reduced charge overpotential (0.48 V) via a rational optimization of Mn/Co molar ratio = 8/2 is achieved. Further computational studies indicate that the different morphologies of Li2O2 should be related to different electronic conductivity and binding of Li2O2 on crystal facets of MnxCo1-xO catalysts, finally leading to different charge overpotential. We anticipate that this specific crystal phase engineering would offer good technical support for developing high-performance transition metal oxide catalysts for advanced Li-O2 batteries.

Identification of an Intermediate Form of Ferredoxin That Binds Only Iron Suggests That Conversion to Holo-Ferredoxin Is Independent of the ISC System in Escherichia coli.

Escherichia coli [2Fe-2S]-ferredoxin and other ISC proteins encoded by the iscRSUA-hscBA-fdx-iscX (isc) operon are responsible for the assembly of iron-sulfur clusters. It is proposed that ferredoxin (Fdx) donates electrons from its reduced [2Fe-2S] center to iron-sulfur cluster biogenesis reactions. However, the underlying mechanisms of the [2Fe-2S] cluster assembly in Fdx remain elusive. Here, we report that Fdx preferentially binds iron, but not the [2Fe-2S] cluster, under cold stress conditions (≤16°C). The iron binding in Fdx is characterized by a unique absorption peak at 320 nm based on UV-visible spectroscopy. In addition, the iron-binding form of Fdx could be converted to the [2Fe-2S] cluster-bound form after transferring cold-stressed cells to normal cultivation temperatures above 25°C. In vitro experiments also revealed that Fdx could utilize bound iron to assemble the [2Fe-2S] cluster by itself. Furthermore, inactivation of the genes encoding IscS, IscU, and IscA did not limit [2Fe-2S] cluster assembly in Fdx, which was also observed by inactivating the isc or suf operon, indicating that iron-sulfur cluster biogenesis in Fdx arose from a unique pathway in E. coli Our results suggest that the intracellular assembly of [2Fe-2S] clusters in Fdx is susceptible to environmental temperatures. The iron binding form of Fdx (Fe-Fdx) is a precursor during its maturation to a cluster binding form ([2Fe-2S]-Fdx), and reassembly of the [2Fe-2S] clusters during temperature increases is not strictly reliant on other specific iron donors and scaffold proteins within the Isc or Suf system.IMPORTANCE Fdx is an electron carrier that is required for the maturation of many other iron-sulfur proteins. Its function strictly depends on its [2Fe-2S] center that bonds with the cysteinyl S atoms of four cysteine residues within Fdx. However, the assembly mechanism of the [2Fe-2S] clusters in Fdx remains controversial. This study reports that Fdx fails to form its [2Fe-2S] cluster under cold stress conditions but instead binds a single Fe atom at the cluster binding site. Moreover, when temperatures increase, Fdx can assemble clusters by itself from its iron-only binding form in E. coli cells. The possibility remains that Fdx can effectively accept clusters from multiple sources. Nevertheless, our results suggest that Fdx has a strong iron binding activity that contributes to the assembly of its own [2Fe-2S] cluster and that Fdx acts as a temperature sensor to regulate Isc system-mediated iron-sulfur cluster biogenesis.

Iron-sulphur cluster biogenesis factor LYRM4 is a novel prognostic biomarker associated with immune infiltrates in hepatocellular carcinoma.

BACKGROUND: LYRM4 is necessary to maintain the stability and activity of the human cysteine desulfurase complex NFS1-LYRM4-ACP. The existing experimental results indicate that cancer cells rely on the high expression of NFS1. However, the role of LYRM4 in liver hepatocellular carcinoma (LIHC) remains unclear. METHODS: In this study, we combined bioinformatics analysis and clinical specimens to evaluate the mRNA, protein expression, and gene regulatory network of LYRM4 in LIHC. Furthermore, we detected the activity of several classical iron-sulphur proteins in LIHC cell lines through UV-vis spectrophotometry. RESULTS: The mRNA and protein levels of LYRM4 were upregulated in LIHC. Subsequent analysis revealed that the LYRM4 mRNA expression was related to various clinical stratifications, prognosis, and survival of LIHC patients. In addition, the mRNA expression of LYRM4 was significantly associated with ALT, tumour thrombus, and encapsulation of HBV-related LIHC patients. IHC results confirmed that LYRM4 was highly expressed in LIHC tissues and showed that the expression of LYRM4 protein in LIHC was significantly correlated with age and serum low-density lipoprotein (LDL) and triglyceride (TG) content. In particular, the mRNA expression of key iron- sulphur proteins POLD1 and PRIM2 was significantly overexpressed and correlated with poor prognosis in LIHC patients. Compared with hepatocytes, the activities of mitochondrial complex I and aconitate hydratase (ACO2) in LIHC cell lines were significantly increased. These results indicated that the iron-sulphur cluster (ISC) biosynthesis was significantly elevated in LIHC, leading to ISC-dependent metabolic reprogramming. Changes in the activity of ISC-dependent proteins may also occur in paracancerous tissues. Further analysis of the biological interaction and gene regulation networks of LYRM4 suggested that these genes were mainly involved in the citric acid cycle and oxidative phosphorylation. Finally, LYRM4 expression in LIHC was significantly positively correlated with the infiltrating levels of six immune cell types, and both factors were strongly associated with prognosis. CONCLUSION: LYRM4 could be a novel prognostic biomarker and molecular target for LIHC therapy. In particular, the potential regulatory networks of LYRM4 overexpression in LIHC provide a scientific basis for future research on the role of the ISC assembly mechanism and LYRM4-mediated sulphur transfer routes in carcinogenesis.

Tuning Li2O2 Formation Routes by Facet Engineering of MnO2 Cathode Catalysts.

In lithium-oxygen batteries, the solubility of LiO2 intermediates in the electrolyte regulates the formation routes of the Li2O2 discharge product. High-donor-number electrolytes with a high solubility of LiO2 tend to promote the formation of Li2O2 large particles following the solution route, which eventually benefits the cell capacity and cycle life. Here, we propose that facet engineering of cathode catalysts could be another direction in tuning the formation routes of Li2O2. In this work, ß-MnO2 crystals with high occupancies of {111} or {100} facets were adopted as cathode catalysts in Li-O2 batteries with a tetra(ethylene)glycol dimethyl ether electrolyte. The {111}-dominated ß-MnO2 catalyzed the formation of the Li2O2 discharge product into large toroids following the solution routes, while {100}-dominated ß-MnO2 facilitated the formation of Li2O2 thin films through the surface routes. Further computational studies indicate that the different formation routes of Li2O2 could be related to different adsorption energies of LiO2 on the two facets of ß-MnO2. Our results demonstrate that facet engineering of cathode catalysts could be a new way to tune the formation route of Li2O2 in a low-donor-number electrolyte. We anticipate that this new finding would offer more choices for the design of lithium-oxygen batteries with high capacities and ultimately a long cycle life.

Zinc Toxicity and Iron-Sulfur Cluster Biogenesis in Escherichia coli.

While zinc is an essential trace metal in biology, excess zinc is toxic to organisms. Previous studies have shown that zinc toxicity is associated with disruption of the [4Fe-4S] clusters in various dehydratases in Escherichia coli Here, we report that the intracellular zinc overload in E. coli cells inhibits iron-sulfur cluster biogenesis without affecting the preassembled iron-sulfur clusters in proteins. Among the housekeeping iron-sulfur cluster assembly proteins encoded by the gene cluster iscSUA-hscBA-fdx-iscX in E. coli cells, the scaffold IscU, the iron chaperone IscA, and ferredoxin have strong zinc binding activity in cells, suggesting that intracellular zinc overload inhibits iron-sulfur cluster biogenesis by binding to the iron-sulfur cluster assembly proteins. Mutations of the conserved cysteine residues to serine in IscA, IscU, or ferredoxin completely abolish the zinc binding activity of the proteins, indicating that zinc can compete with iron or iron-sulfur cluster binding in IscA, IscU, and ferredoxin and block iron-sulfur cluster biogenesis. Furthermore, intracellular zinc overload appears to emulate the slow-growth phenotype of the E. coli mutant cells with deletion of the iron-sulfur cluster assembly proteins IscU, IscA, and ferredoxin. Our results suggest that intracellular zinc overload inhibits iron-sulfur cluster biogenesis by targeting the iron-sulfur cluster assembly proteins IscU, IscA, and ferredoxin in E. coli cells.IMPORTANCE Zinc toxicity has been implicated in causing various human diseases. High concentrations of zinc can also inhibit bacterial cell growth. However, the underlying mechanism has not been fully understood. Here, we report that zinc overload in Escherichia coli cells inhibits iron-sulfur cluster biogenesis by targeting specific iron-sulfur cluster assembly proteins. Because iron-sulfur proteins are involved in diverse physiological processes, the zinc-mediated inhibition of iron-sulfur cluster biogenesis could be largely responsible for the zinc-mediated cytotoxicity. Our finding provides new insights on how intracellular zinc overload may inhibit cellular functions in bacteria.

The prognostic value of serum amyloid A in solid tumors: a meta-analysis.

BACKGROUND: Previous studies have demonstrated that serum amyloid A (SAA) levels are correlated with the clinical outcomes of solid tumors. However, the available data have not been systematically evaluated. The objective of the present meta-analysis was to explore the prognostic value of SAA levels in solid tumors. METHODS: Eligible studies were identified from the PubMed, EMBASE and Science Citation Index electronic databases. The clinical characteristics, disease/progression-free survival (DFS/PFS) and overall survival (OS) were extracted from the eligible studies. The pooled hazard ratios (HRs) and 95% confidence intervals (CIs) were calculated with Stata 12.0 software. We also performed subgroup, meta-regression and sensitivity analyses. RESULTS: In total, 12 eligible studies including 2749 patients were enrolled in the present meta-analysis. The pooled HRs with 95% CIs showed that elevated levels of SAA were significantly associated with poor OS (HR = 3.01, 95% CI 1.96-4.63) and DFS/PFS (HR = 1.67, 95% CI 1.31-2.12) in patients with solid tumors. Although publication bias was seem found in the studies with regard to OS, a further trim and fill analysis revealed that the adjusted HR was 3.02 (95% CI 1.96-4.63), which was close to the original HR. Subgroup analysis confirmed an elevated level of SAA as a strong prognostic marker in patients with solid tumors, regardless of tumor type, detection method, cut-off value, sample size, area and variance analyses. CONCLUSION: Our meta-analysis indicated that elevated levels of SAA might be an unfavorable prognostic marker for OS in patients with solid tumors.

Biodetection and bioremediation of copper ions in environmental water samples using a temperature-controlled, dual-functional Escherichia coli cell.

Although a variety of whole-cell biosensors and biosorbents have been developed for detection and removal of heavy metal contaminants, few whole cells can be applied to both monitoring and remediation of copper pollution in water. In this study, a modified plasmid was constructed by incorporating a copper-sensing element and a copper-adsorbing element into a temperature-inducible plasmid, pBV220. This plasmid was subsequently transformed into an engineered Escherichia coli strain lacking copA and cueO. This dual-functional E. coli cell selectively responded to copper ions with a linear detection range of 0.01-25 µM at 37 °C and could express surface-displayed CueR when treated at 42 °C without any costly chemical inducers. The display of CueR on the cell surface specifically enhanced its copper adsorption capacity and rapidly removed copper ions from aqueous solutions. In addition, the CueR surface-displayed cells could be regenerated by adsorption-desorption cycles via pH regulation. Moreover, by simply using two different temperatures, the detection or adsorption of copper using this dual-functional whole cell was achieved without any cross-interference. Most importantly, it provided highly sensitive, accurate quantification, and effective removal of copper in real environmental water samples. Thus, this E. coli cell can be used for large-scale detection and remediation of copper pollutants.

Insight into Ca-Substitution Effects on O3-Type NaNi1/3 Fe1/3 Mn1/3 O2 Cathode Materials for Sodium-Ion Batteries Application.

O3-type NaNi1/3 Fe1/3 Mn1/3 O2 (NaNFM) is well investigated as a promising cathode material for sodium-ion batteries (SIBs), but the cycling stability of NaNFM still needs to be improved by using novel electrolytes or optimizing their structure with the substitution of different elements sites. To enlarge the alkali-layer distance inside the layer structure of NaNFM may benefit Na+ diffusion. Herein, the effect of Ca-substitution is reported in Na sites on the structural and electrochemical properties of Na1-x Cax/2 NFM (x = 0, 0.05, 0.1). X-ray diffraction (XRD) patterns of the prepared Na1-x Cax/2 NFM samples show single α-NaFeO2 type phase with slightly increased alkali-layer distance as Ca content increases. The cycling stabilities of Ca-substituted samples are remarkably improved. The Na0.9 Ca0.05 Ni1/3 Fe1/3 Mn1/3 O2 (Na0.9 Ca0.05 NFM) cathode delivers a capacity of 116.3 mAh g-1 with capacity retention of 92% after 200 cycles at 1C rate. In operando XRD indicates a reversible structural evolution through an O3-P3-P3-O3 sequence of Na0.9 Ca0.05 NFM cathode during cycling. Compared to NaNMF, the Na0.9 Ca0.05 NFM cathode shows a wider voltage range in pure P3 phase state during the charge/discharge process and exhibits better structure recoverability after cycling. The superior cycling stability of Na0.9 Ca0.05 NFM makes it a promising material for practical applications in sodium-ion batteries.

Toward Highly Efficient Electrocatalyst for Li-O2 Batteries Using Biphasic N-Doping Cobalt@Graphene Multiple-Capsule Heterostructures.

For the promotion of lithium-oxygen batteries available for practical applications, the development of advanced cathode catalysts with low-cost, high activity, and stable structural properties is demanded. Such development is rooted on certain intelligent catalyst-electrode design that fundamentally facilitates electronic and ionic transport and improves oxygen diffusivity in a porous environment. Here we design a biphasic nitrogen-doped cobalt@graphene multiple-capsule heterostructure, combined with a flexible, stable porous electrode architecture, and apply it as promising cathodes for lithium-oxygen cells. The biphasic nitrogen-doping feature improves the electric conductivity and catalytic activity; the multiple-nanocapsule configuration makes high/uniform electroactive zones possible; furthermore, the colander-like porous electrode facilitates the oxygen diffusion, catalytic reaction, and stable deposition of discharge products. As a result, the electrode exhibits much improved electrocatalytic properties associated with unique morphologies of electrochemically grown lithium peroxides.

Anaerobic Copper Toxicity and Iron-Sulfur Cluster Biogenesis in Escherichia coli.

While copper is an essential trace element in biology, pollution of groundwater from copper has become a threat to all living organisms. Cellular mechanisms underlying copper toxicity, however, are still not fully understood. Previous studies have shown that iron-sulfur proteins are among the primary targets of copper toxicity in Escherichia coli under aerobic conditions. Here, we report that, under anaerobic conditions, iron-sulfur proteins in E. coli cells are even more susceptible to copper in medium. Whereas addition of 0.2 mM copper(II) chloride to LB (Luria-Bertani) medium has very little or no effect on iron-sulfur proteins in wild-type E. coli cells under aerobic conditions, the same copper treatment largely inactivates iron-sulfur proteins by blocking iron-sulfur cluster biogenesis in the cells under anaerobic conditions. Importantly, proteins that do not have iron-sulfur clusters (e.g., fumarase C and cysteine desulfurase) in E. coli cells are not significantly affected by copper treatment under aerobic or anaerobic conditions, indicating that copper may specifically target iron-sulfur proteins in cells. Additional studies revealed that E. coli cells accumulate more intracellular copper under anaerobic conditions than under aerobic conditions and that the elevated copper content binds to the iron-sulfur cluster assembly proteins IscU and IscA, which effectively inhibits iron-sulfur cluster biogenesis. The results suggest that the copper-mediated inhibition of iron-sulfur proteins does not require oxygen and that iron-sulfur cluster biogenesis is the primary target of anaerobic copper toxicity in cells.IMPORTANCE Copper contamination in groundwater has become a threat to all living organisms. However, cellular mechanisms underlying copper toxicity have not been fully understood up to now. The work described here reveals that iron-sulfur proteins in Escherichia coli cells are much more susceptible to copper in medium under anaerobic conditions than they are under aerobic conditions. Under anaerobic conditions, E. coli cells accumulate excess intracellular copper, which specifically targets iron-sulfur proteins by blocking iron-sulfur cluster biogenesis. Since iron-sulfur proteins are involved in diverse and vital physiological processes, inhibition of iron-sulfur cluster biogenesis by copper disrupts multiple cellular functions and ultimately inhibits cell growth. The results from this study illustrate a new interplay between intracellular copper toxicity and iron-sulfur cluster biogenesis in bacterial cells under anaerobic conditions.

Solid-State Li-Ion Batteries Using Fast, Stable, Glassy Nanocomposite Electrolytes for Good Safety and Long Cycle-Life.

The development of safe, stable, and long-life Li-ion batteries is being intensively pursued to enable the electrification of transportation and intelligent grid applications. Here, we report a new solid-state Li-ion battery technology, using a solid nanocomposite electrolyte composed of porous silica matrices with in situ immobilizing Li(+)-conducting ionic liquid, anode material of MCMB, and cathode material of LiCoO2, LiNi1/3Co1/3Mn1/3O2, or LiFePO4. An injection printing method is used for the electrode/electrolyte preparation. Solid nanocomposite electrolytes exhibit superior performance to the conventional organic electrolytes with regard to safety and cycle-life. They also have a transparent glassy structure with high ionic conductivity and good mechanical strength. Solid-state full cells tested with the various cathodes exhibited high specific capacities, long cycling stability, and excellent high temperature performance. This solid-state battery technology will provide new avenues for the rational engineering of advanced Li-ion batteries and other electrochemical devices.

Deletion of the Proposed Iron Chaperones IscA/SufA Results in Accumulation of a Red Intermediate Cysteine Desulfurase IscS in Escherichia coli.

In Escherichia coli, sulfur in iron-sulfur clusters is primarily derived from L-cysteine via the cysteine desulfurase IscS. However, the iron donor for iron-sulfur cluster assembly remains elusive. Previous studies have shown that, among the iron-sulfur cluster assembly proteins in E. coli, IscA has a unique and strong iron-binding activity and that the iron-bound IscA can efficiently provide iron for iron-sulfur cluster assembly in proteins in vitro, indicating that IscA may act as an iron chaperone for iron-sulfur cluster biogenesis. Here we report that deletion of IscA and its paralog SufA in E. coli cells results in the accumulation of a red-colored cysteine desulfurase IscS under aerobic growth conditions. Depletion of intracellular iron using a membrane-permeable iron chelator, 2,2'-dipyridyl, also leads to the accumulation of red IscS in wild-type E. coli cells, suggesting that the deletion of IscA/SufA may be emulated by depletion of intracellular iron. Purified red IscS has an absorption peak at 528 nm in addition to the peak at 395 nm of pyridoxal 5'-phosphate. When red IscS is oxidized by hydrogen peroxide, the peak at 528 nm is shifted to 510 nm, which is similar to that of alanine-quinonoid intermediate in cysteine desulfurases. Indeed, red IscS can also be produced in vitro by incubating wild-type IscS with excess L-alanine and sulfide. The results led us to propose that deletion of IscA/SufA may disrupt the iron delivery for iron-sulfur cluster biogenesis, therefore impeding sulfur delivery by IscS, and result in the accumulation of red IscS in E. coli cells.

His-87 ligand in mitoNEET is crucial for the transfer of iron sulfur clusters from mitochondria to cytosolic aconitase.

MitoNEET is the first identified iron sulfur protein that located in the mitochondrial outer membrane. We showed that knockdown of mitoNEET did not affect the iron sulfur protein expression in mitochondria and cytoplasm, but significantly reduced the cytosolic aconitase activity. The reduction of aconitase activity was rescued by transfection of wild type mitoNEET, but not by mitoNEET mutants H87C and H87S. Our results confirm the observation that mitoNEET is important in transferring the iron sulfur clusters to the cytosolic aconitase in living cells and the His-87 ligand in mitoNEET plays important role in this process.