Synergetic Dual-Additive Electrolyte Enables Highly Stable Performance in Sodium Metal Batteries.

Sodium (Na)-metal batteries (SMBs) are considered one of the most promising candidates for the large-scale energy storage market owing to their high theoretical capacity (1,166 mAh g-1) and the abundance of Na raw material. However, the limited stability of electrolytes still hindered the application of SMBs. Herein, sulfolane (Sul) and vinylene carbonate (VC) are identified as effective dual additives that can largely stabilize propylene carbonate (PC)-based electrolytes, prevent dendrite growth, and extend the cycle life of SMBs. The cycling stability of the Na/NaNi0.68Mn0.22Co0.1O2 (NaNMC) cell with this dual-additive electrolyte is remarkably enhanced, with a capacity retention of 94% and a Coulombic efficiency (CE) of 99.9% over 600 cycles at a 5 C (750 mA g-1) rate. The superior cycling performance of the cells can be attributed to the homogenous, dense, and thin hybrid solid electrolyte interphase consisting of F- and S-containing species on the surface of both the Na metal anode and the NaNMC cathode by adding dual additives. Such unique interphases can effectively facilitate Na-ion transport kinetics and avoid electrolyte depletion during repeated cycling at a very high rate of 5 C. This electrolyte design is believed to result in further improvements in the performance of SMBs.

Localized high-concentration electrolytes get more localized through micelle-like structures.

Liquid electrolytes in batteries are typically treated as macroscopically homogeneous ionic transport media despite having a complex chemical composition and atomistic solvation structures, leaving a knowledge gap of the microstructural characteristics. Here, we reveal a unique micelle-like structure in a localized high-concentration electrolyte, in which the solvent acts as a surfactant between an insoluble salt in a diluent. The miscibility of the solvent with the diluent and simultaneous solubility of the salt results in a micelle-like structure with a smeared interface and an increased salt concentration at the centre of the salt-solvent clusters that extends the salt solubility. These intermingling miscibility effects have temperature dependencies, wherein a typical localized high-concentration electrolyte peaks in localized cluster salt concentration near room temperature and is used to form a stable solid-electrolyte interphase on a Li metal anode. These findings serve as a guide to predicting a stable ternary phase diagram and connecting the electrolyte microstructure with electrolyte formulation and formation protocols of solid-electrolyte interphases for enhanced battery cyclability.

Effects of fluorinated solvents on electrolyte solvation structures and electrode/electrolyte interphases for lithium metal batteries.

Electrolyte is very critical to the performance of the high-voltage lithium (Li) metal battery (LMB), which is one of the most attractive candidates for the next-generation high-density energy-storage systems. Electrolyte formulation and structure determine the physical properties of the electrolytes and their interfacial chemistries on the electrode surfaces. Localized high-concentration electrolytes (LHCEs) outperform state-of-the-art carbonate electrolytes in many aspects in LMBs due to their unique solvation structures. Types of fluorinated cosolvents used in LHCEs are investigated here in searching for the most suitable diluent for high-concentration electrolytes (HCEs). Nonsolvating solvents (including fluorinated ethers, fluorinated borate, and fluorinated orthoformate) added in HCEs enable the formation of LHCEs with high-concentration solvation structures. However, low-solvating fluorinated carbonate will coordinate with Li+ ions and form a second solvation shell or a pseudo-LHCE which diminishes the benefits of LHCE. In addition, it is evident that the diluent has significant influence on the electrode/electrolyte interphases (EEIs) beyond retaining the high-concentration solvation structures. Diluent molecules surrounding the high-concentration clusters could accelerate or decelerate the anion decomposition through coparticipation of diluent decomposition in the EEI formation. The varied interphase features lead to significantly different battery performance. This study points out the importance of diluents and their synergetic effects with the conductive salt and the solvating solvent in designing LHCEs. These systematic comparisons and fundamental insights into LHCEs using different types of fluorinated solvents can guide further development of advanced electrolytes for high-voltage LMBs.

In Situ Visualization of the Pinning Effect of Planar Defects on Li Ion Insertion.

Longevity of Li ion batteries strongly depends on the interaction of transporting Li ions in electrode crystals with defects. However, detailed interactions between the Li ion flux and structural defects in the host crystal remain obscure due to the transient nature of such interactions. Here, by in situ transmission electron microscopy and density function theory calculations, we reveal how the diffusion pathways and transport kinetics of a Li ion can be affected by planar defects in a tungsten trioxide lattice. We uncover that changes in charge distribution and lattice spacing along the planar defects disrupt the continuity of ion conduction channels and dramatically increase the energy barrier of Li diffusion, thus, arresting Li ions at the defect sites and twisting the lithiation front. The atomic-scale understanding holds critical implications for rational interface design in solid-state batteries and solid oxide fuel cells.

Role of inner solvation sheath within salt-solvent complexes in tailoring electrode/electrolyte interphases for lithium metal batteries.

Functional electrolyte is the key to stabilize the highly reductive lithium (Li) metal anode and the high-voltage cathode for long-life, high-energy-density rechargeable Li metal batteries (LMBs). However, fundamental mechanisms on the interactions between reactive electrodes and electrolytes are still not well understood. Recently localized high-concentration electrolytes (LHCEs) are emerging as a promising electrolyte design strategy for LMBs. Here, we use LHCEs as an ideal platform to investigate the fundamental correlation between the reactive characteristics of the inner solvation sheath on electrode surfaces due to their unique solvation structures. The effects of a series of LHCEs with model electrolyte solvents (carbonate, sulfone, phosphate, and ether) on the stability of high-voltage LMBs are systematically studied. The stabilities of electrodes in different LHCEs indicate the intrinsic synergistic effects between the salt and the solvent when they coexist on electrode surfaces. Experimental and theoretical analyses reveal an intriguing general rule that the strong interactions between the salt and the solvent in the inner solvation sheath promote their intermolecular proton/charge transfer reactions, which dictates the properties of the electrode/electrolyte interphases and thus the battery performances.

Lithium Metal Anodes with Nonaqueous Electrolytes.

High-energy rechargeable lithium (Li) metal batteries (LMBs) with Li metal anode (LMA) were first developed in the 1970s, but their practical applications have been hindered by the safety and low-efficiency concerns related to LMA. Recently, a worldwide effort on LMA-based rechargeable LMBs has been revived to replace graphite-based, Li-ion batteries because of the much higher energy density that can be achieved with LMBs. This review focuses on the recent progress on the stabilization of LMA with nonaqueous electrolytes and reveals the fundamental mechanisms behind this improved stability. Various strategies that can enhance the stability of LMA in practical conditions and perspectives on the future development of LMA are also discussed. These strategies include the use of novel electrolytes such as superconcentrated electrolytes, localized high-concentration electrolytes, and highly fluorinated electrolytes, surface coatings that can form a solid electrolyte interphase with a high interfacial energy and self-healing capabilities, development of "anode-free" Li batteries to minimize the interaction between LMA and electrolyte, approaches to enable operation of LMA in practical conditions, etc. Combination of these strategies ultimately will lead us closer to the large-scale application of LMBs which often is called the "Holy Grail" of energy storage systems.

Glassy Li metal anode for high-performance rechargeable Li batteries.

Lithium metal has been considered an ideal anode for high-energy rechargeable Li batteries, although its nucleation and growth process remains mysterious, especially at the nanoscale. Here, cryogenic transmission electron microscopy was used to reveal the evolving nanostructure of Li metal deposits at various transient states in the nucleation and growth process, in which a disorder-order phase transition was observed as a function of current density and deposition time. The atomic interaction over wide spatial and temporal scales was depicted by reactive molecular dynamics simulations to assist in understanding the kinetics. Compared to crystalline Li, glassy Li outperforms in electrochemical reversibility, and it has a desired structure for high-energy rechargeable Li batteries. Our findings correlate the crystallinity of the nuclei with the subsequent growth of the nanostructure and morphology, and provide strategies to control and shape the mesostructure of Li metal to achieve high performance in rechargeable Li batteries.

Inspecting the structural characteristics of chiral drug penicillamine under different pH conditions using Raman optical activity spectroscopy and DFT calculations.

The investigation of the structural characteristics of chiral drugs in physiological environments is a challenging research topic, which may lead to a better understanding of how the drugs work. Raman optical activity (ROA) spectroscopy in combination with density functional theory (DFT) calculations was exploited to inspect the structural changes in penicillamine under different acid-base states in aqueous solutions. The B3LYP/aug-cc-PVDZ method was employed and the implicit solvation model density (SMD) was considered for describing the solvation effect in H2O. The conformations of penicillamine varied with pH, but penicillamine was liable to stabilize in the form of the PC conformation (the sulfur atom is in a trans orientation with respect to carboxylate) in most cases for both D- and L-isomers. The relationship between the conformations of penicillamine and the ROA peaks, as well as peak assignments, were comprehensively studied and elucidated. In the fingerprint region, two ROA couplets and one ROA triplet with different patterns were recognized. The intensity, sign and frequency of the corresponding peaks also changed with varying pH. Deuteration was carried out to identify the vibrational modes, and the ROA peaks of the deuterated amino group in particular are sensitive to change in the ambient environment. The results are expected not only to serve as a reference for the interpretation of the ROA spectra of penicillamine and other chiral drugs with analogous structures but also to evaluate the structural changes of chiral molecules in physiological environments, which will form the basis of further exploration of the effects of structural characteristics on the pharmacological and toxicological properties of chiral drugs.

Atomic to Nanoscale Origin of Vinylene Carbonate Enhanced Cycling Stability of Lithium Metal Anode Revealed by Cryo-Transmission Electron Microscopy.

Batteries using lithium (Li) metal as the anode are considered promising energy storage systems because of their high specific energy densities. The crucial bottlenecks for Li metal anode are Li dendrites growth and side reactions with electrolyte inducing safety concern, low Coulombic efficiency (CE), and short cycle life. Vinylene carbonate (VC), as an effective electrolyte additive in Li-ion batteries, has been noticed to significantly enhance the CE, whereas the origin of such an additive remains unclear. Here we use cryogenic transmission electron microscopy imaging combing with energy dispersive X-ray spectroscopy elemental and electron energy loss spectroscopy electronic structure analyses to reveal the role of the VC additive. We discovered that the electrochemically deposited Li metal (EDLi) in the VC-containing electrolyte is slightly oxidized with the solid electrolyte interphase (SEI) being a nanoscale mosaic-like structure comprised of organic species, Li2O and Li2CO3, whereas the EDLi formed in the VC-free electrolyte is featured by a combination of fully oxidized Li with Li2O SEI layer and pure Li metal with multilayer nanostructured SEI. These results highlight the possible tuning of crucial structural and chemical features of EDLi and SEI through additives and consequently direct correlation with electrochemical performance, providing valuable guidelines to rational selection, design, and synthesis of additives for new battery chemistries.

Optimization of Magnesium-Doped Lithium Metal Anode for High Performance Lithium Metal Batteries through Modeling and Experiment.

Lithium (Li)-magnesium (Mg) alloy with limited Mg amount, which can also be called Mg-doped Li (Li-Mg), has been considered as a potential alternative anode for high energy density rechargeable Li metal batteries. However, the optimum doping-content of Mg in Li-Mg anode and the mechanism of the improved performance are not well understood. Herein, density functional theory (DFT) calculations are used to investigate the effect of Mg amount in Li-Mg anode. The Li-Mg with about 5 wt. % Mg (abbreviated as Li-Mg5) has the lowest absorption energy of Li, thus all the surface area can be "controlled" by Mg atoms, leading to the smooth and continuous deposition of Li on the surface around the Mg center. A localized high concentration electrolyte enables Li-Mg5 to exhibit the best cycling stability in Li metal batteries with high-loading cathode and lean electrolyte under 4.4 V high-voltage, which is approaching the demand of practical application. This electrolyte also helps generate an inorganic-rich solid electrolyte interphase, which leads to smooth, compact and less corrosion layer on the Li-Mg5 surface. Both theoretical simulations and experimental results prove that Li-Mg5 has optimum Mg content and gives best battery cycling performance.

Atomic Resolution Structural and Chemical Imaging Revealing the Sequential Migration of Ni, Co, and Mn upon the Battery Cycling of Layered Cathode.

Layered lithium transition metal oxides (LTMO) are promising candidate cathode materials for next-generation high-energy density lithium ion battery. The challenge for using this category of cathode is the capacity and voltage fading, which is believed to be associated with the layered structure disordering, a process that is initiated from the surface or solid-electrolyte interface and facilitated by transition metal (TM) reduction and oxygen vacancy formation. However, the atomic level dynamic mechanism of such a layered structure disordering is still not fully clear. In this work, utilizing atomic resolution electron energy loss spectroscopy (EELS), we map, for the first time at atomic scale, the spatial evolution of Ni, Co and Mn in a cycled LiNi1/3Mn1/3Co1/3O2 layered cathode. In combination with atomic level structural imaging, we discovered the direct correlation of TM ions migration behavior with lattice disordering, featuring the residing of TM ions in the tetrahedral site and a sequential migration of Ni, Co, and Mn upon the increased lattice disordering of the layered structure. This work highlights that Ni ions, though acting as the dominant redox species in many LTMO, are labile to migrate to cause lattice disordering upon battery cycling, while the Mn ions are more stable as compared with Ni and Co and can act as pillar to stabilize layered structure. Direct visualization of the behavior of TM ions during the battery cycling provides insight for designing of cathode with high structural stability and correspondingly a superior performance.

Complete Decomposition of Li2CO3 in Li-O2 Batteries Using Ir/B4C as Noncarbon-Based Oxygen Electrode.

Instability of carbon-based oxygen electrodes and incomplete decomposition of Li2CO3 during charge process are critical barriers for rechargeable Li-O2 batteries. Here we report the complete decomposition of Li2CO3 in Li-O2 batteries using the ultrafine iridium-decorated boron carbide (Ir/B4C) nanocomposite as a noncarbon based oxygen electrode. The systematic investigation on charging the Li2CO3 preloaded Ir/B4C electrode in an ether-based electrolyte demonstrates that the Ir/B4C electrode can decompose Li2CO3 with an efficiency close to 100% at a voltage below 4.37 V. In contrast, the bare B4C without Ir electrocatalyst can only decompose 4.7% of the preloaded Li2CO3. Theoretical analysis indicates that the high efficiency decomposition of Li2CO3 can be attributed to the synergistic effects of Ir and B4C. Ir has a high affinity for oxygen species, which could lower the energy barrier for electrochemical oxidation of Li2CO3. B4C exhibits much higher chemical and electrochemical stability than carbon-based electrodes and high catalytic activity for Li-O2 reactions. A Li-O2 battery using Ir/B4C as the oxygen electrode material shows highly enhanced cycling stability than those using the bare B4C oxygen electrode. Further development of these stable oxygen-electrodes could accelerate practical applications of Li-O2 batteries.

New Insights on the Structure of Electrochemically Deposited Lithium Metal and Its Solid Electrolyte Interphases via Cryogenic TEM.

Lithium metal has been considered the "holy grail" anode material for rechargeable batteries despite the fact that its dendritic growth and low Coulombic efficiency (CE) have crippled its practical use for decades. Its high chemical reactivity and low stability make it difficult to explore the intrinsic chemical and physical properties of the electrochemically deposited lithium (EDLi) and its accompanying solid electrolyte interphase (SEI). To prevent the dendritic growth and enhance the electrochemical reversibility, it is crucial to understand the nano- and mesostructures of EDLi. However, Li metal is very sensitive to beam damage and has low contrast for commonly used characterization techniques such as electron microscopy. Inspired by biological imaging techniques, this work demonstrates the power of cryogenic (cryo)-electron microscopy to reveal the detailed structure of EDLi and the SEI composition at the nanoscale while minimizing beam damage during imaging. Surprisingly, the results show that the nucleation-dominated EDLi (5 min at 0.5 mA cm-2) is amorphous, while there is some crystalline LiF present in the SEI. The EDLi grown from various electrolytes with different additives exhibits distinctive surface properties. Consequently, these results highlight the importance of the SEI and its relationship with the CE. Our findings not only illustrate the capabilities of cryogenic microscopy for beam (thermal)-sensitive materials but also yield crucial structural information on the EDLi evolution with and without electrolyte additives.

Formation of Reversible Solid Electrolyte Interface on Graphite Surface from Concentrated Electrolytes.

Li-ion batteries (LIB) have been successfully commercialized after the identification of ethylene-carbonate (EC)-containing electrolyte that can form a stable solid electrolyte interphase (SEI) on carbon anode surface to passivate further side reactions but still enable the transportation of the Li+ cation. These electrolytes are still utilized, with only minor changes, after three decades. However, the long-term cycling of LIB leads to continuous consumption of electrolyte and growth of SEI layer on the electrode surface, which limits the battery's life and performance. Herein, a new anode protection mechanism is reported in which, upon changing of the cell potential, the electrolyte components at the electrode-electrolyte interface reorganize reversibly to form a transient protective surface layers on the anode. This layer will disappear after the applied potential is removed so that no permanent SEI layer is required to protect the carbon anode. This phenomenon minimizes the need for a permanent SEI layer and prevents its continuous growth and therefore may lead to largely improved performance for LIBs.

Improving Lithium-Sulfur Battery Performance under Lean Electrolyte through Nanoscale Confinement in Soft Swellable Gels.

Li-S batteries have been extensively studied using rigid carbon as the host for sulfur encapsulation, but improving the properties with a reduced electrolyte amount remains a significant challenge. This is critical for achieving high energy density. Here, we developed a soft PEO10LiTFSI polymer swellable gel as a nanoscale reservoir to trap the polysulfides under lean electrolyte conditions. The PEO10LiTFSI gel immobilizes the electrolyte and confines polysulfides within the ion conducting phase. The Li-S cell with a much lower electrolyte to sulfur ratio (E/S) of 4 gE/gS (3.3 mLE/gS) could deliver a capacity of 1200 mA h/g, 4.6 mA h/cm2, and good cycle life. The accumulation of polysulfide reduction products, such as Li2S, on the cathode, is identified as the potential mechanism for capacity fading under lean electrolyte conditions.

Electrochemically Formed Ultrafine Metal Oxide Nanocatalysts for High-Performance Lithium-Oxygen Batteries.

Lithium-oxygen (Li-O2) batteries have an extremely high theoretical specific energy density when compared with conventional energy-storage systems. However, practical application of the Li-O2 battery system still faces significant challenges. In this work, we report a new approach for synthesis of ultrafine metal oxide nanocatalysts through an electrochemical prelithiation process. This process reduces the size of NiCo2O4 (NCO) particles from 20-30 nm to a uniformly distributed domain of ∼2 nm and significantly improves their catalytic activity. Structurally, the prelithiated NCO nanowires feature ultrafine NiO/CoO nanoparticles that are highly stable during prolonged cycles in terms of morphology and particle size, thus maintaining an excellent catalytic effect to oxygen reduction and evolution reactions. A Li-O2 battery using this catalyst demonstrated an initial capacity of 29 280 mAh g(-1) and retained a capacity of >1000 mAh g(-1) after 100 cycles based on the weight of the NCO active material. Direct in situ transmission electron microscopy observations conclusively revealed the lithiation/delithiation process of as-prepared NCO nanowires and provided in-depth understanding for both catalyst and battery chemistries of transition-metal oxides. This unique electrochemical approach could also be used to form ultrafine nanoparticles of a broad range of materials for catalyst and other applications.

Alteration of the DNA methylation status of donor cells impairs the developmental competence of porcine cloned embryos.

Nuclear reprogramming induced by somatic cell nuclear transfer is an inefficient process, and donor cell DNA methylation status is thought to be a major factor affecting cloning efficiency. Here, the role of donor cell DNA methylation status regulated by 5-aza-2'-deoxycytidine (5-aza-dC) or 5-methyl-2'-deoxycytidine-5'-triphosphate (5-methyl-dCTP) in the early development of porcine cloned embryos was investigated. Our results showed that 5-aza-dC or 5-methyl-dCTP significantly reduced or increased the global methylation levels and altered the methylation and expression levels of key genes in donor cells. However, the development of cloned embryos derived from these cells was reduced. Furthermore, disrupted pseudo-pronucleus formation and transcripts of early embryo development-related genes were observed in cloned embryos derived from these cells. In conclusion, our results demonstrated that alteration of the DNA methylation status of donor cells by 5-aza-dC or 5-methyl-dCTP disrupted nuclear reprogramming and impaired the developmental competence of porcine cloned embryos.

Surface Coating Constraint Induced Self-Discharging of Silicon Nanoparticles as Anodes for Lithium Ion Batteries.

One of the key challenges of Si-based anodes for lithium ion batteries is the large volume change upon lithiation and delithiation, which commonly leads to electrochemi-mechanical degradation and subsequent fast capacity fading. Recent studies have shown that applying nanometer-thick coating layers on Si nanoparticle (SiNPs) enhances cyclability and capacity retention. However, it is far from clear how the coating layer function from the point of view of both surface chemistry and electrochemi-mechanical effect. Herein, we use in situ transmission electron microscopy to investigate the lithiation/delithiation kinetics of SiNPs coated with a conductive polymer, polypyrrole (PPy). We discovered that this coating layer can lead to "self-delithiation" or "self-discharging" at different stages of lithiation. We rationalized that the self-discharging is driven by the internal compressive stress generated inside the lithiated SiNPs due to the constraint effect of the coating layer. We also noticed that the critical size of lithiation-induced fracture of SiNPs is increased from ∼150 nm for bare SiNPs to ∼380 nm for the PPy-coated SiNPs, showing a mechanically protective role of the coating layer. These observations demonstrate both beneficial and detrimental roles of the surface coatings, shedding light on rational design of surface coatings for silicon to retain high-power and high capacity as anode for lithium ion batteries.

Evolution of lattice structure and chemical composition of the surface reconstruction layer in Li(1.2)Ni(0.2)Mn(0.6)O2 cathode material for lithium ion batteries.

Voltage and capacity fading of layer structured lithium and manganese rich (LMR) transition metal oxide is directly related to the structural and composition evolution of the material during the cycling of the battery. However, understanding such evolution at atomic level remains elusive. On the basis of atomic level structural imaging, elemental mapping of the pristine and cycled samples, and density functional theory calculations, it is found that accompanying the hoping of Li ions is the simultaneous migration of Ni ions toward the surface from the bulk lattice, leading to the gradual depletion of Ni in the bulk lattice and thickening of a Ni enriched surface reconstruction layer (SRL). Furthermore, Ni and Mn also exhibit concentration partitions within the thin layer of SRL in the cycled samples where Ni is almost depleted at the very surface of the SRL, indicating the preferential dissolution of Ni ions in the electrolyte. Accompanying the elemental composition evolution, significant structural evolution is also observed and identified as a sequential phase transition of C2/m → I41 → Spinel. For the first time, it is found that the surface facet terminated with pure cation/anion is more stable than that with a mixture of cation and anion. These findings firmly established how the elemental species in the lattice of LMR cathode transfer from the bulk lattice to surface layer and further into the electrolyte, clarifying the long-standing confusion and debate on the structure and chemistry of the surface layer and their correlation with the voltage fading and capacity decaying of LMR cathode. Therefore, this work provides critical insights for design of cathode materials with both high capacity and voltage stability during cycling.