RESUMEN
The mechanical interaction between cells and the extracellular matrix is pervasive in biological systems. On fibrous substrates, cells possess the ability to recruit neighboring fibers, thereby augmenting their own adhesion and facilitating the generation of mechanical cues. However, the matrices with high moduli impede fiber recruitment, restricting the cell mechanoresponse. Herein, by harnessing the inherent swelling properties of gelatin, the flexible gelatin methacryloyl network empowers cells to recruit fibers spanning a broad spectrum of physiological moduli during adhesion. The high flexibility concurrently facilitates the optimization of fiber distribution, deformability, and modulus, contributing to the promotion of cell mechanosensing. Consequently, the randomly distributed flexible fibers with high moduli maximize the cell adhesive forces. This study uncovers the impact of fiber recruitment on cell mechanosensing and introduces fiber flexibility as a previously unexplored property, offering an innovative perspective for the design and development of novel biomaterials.
Asunto(s)
Materiales Biocompatibles , Matriz Extracelular , Materiales Biocompatibles/química , Matriz Extracelular/química , Módulo de ElasticidadRESUMEN
The electrochemical nitrate reduction reaction (NO3RR) is considered a sustainable technology to convert the nitrate pollutants to ammonia. However, developing highly efficient electrocatalysts is necessary and challenging given the slow kinetics of the NO3RR with an eight-electron transfer process. Here, a Cu1.5Mn1.5O4 (CMO)/CeO2 heterostructure with rich interfaces is designed and fabricated through an electrospinning and postprocessing technique. Benefiting from the strong coupling between CMO and CeO2, the optimized CMO/CeO2-2 catalyst presents excellent NO3RR performance, with NH3 Faraday efficiency (FE) up to 93.07 ± 1.45% at -0.481 V vs reversible hydrogen electrode (RHE) and NH3 yield rate up to 48.06 ± 1.32 mg cm-2 h-1 at -0.681 V vs RHE. Theoretical calculations demonstrate that the integration of CeO2 with CMO modulates the adsorption/desorption process of the reactants and intermediates, showing a reduced energy barrier in the rate determination step of NO* to N* and achieving an outstanding NO3RR performance.
RESUMEN
Sealing wet porous membranes is a major challenge when fabricating cell encapsulation devices. Herein, we report the development of an Autoclavable Transparent Thermal Cutter (ATTC) for reliably sealing wet nanofibrous membranes. Notably, the ATTC is autoclavable and transparent, thus enabling in situ visualization of the sealing process in a sterile environment and ensuring an appropriate seal. In addition, the ATTC could generate smooth, arbitrary-shaped sealing ends with excellent mechanical properties when sealing PA6, PVDF, and TPU nanofibrous tubes and PP microporous membranes. Importantly, the ATTC could reliably seal wet nanofibrous tubes, which can shoulder a burst pressure up to 313.2 ± 19.3 kPa without bursting at the sealing ends. Furthermore, the ATTC sealing process is highly compatible with the fabrication of cell encapsulation devices, as verified by viability, proliferation, cell escape, and cell function tests. We believe that the ATTC could be used to reliably seal cell encapsulation devices with minimal side effects.
RESUMEN
Micro/nanofiber-based face masks are recommended as personal protective equipment (PPE) against particulate matter (PM), especially PM0.3. Ensuring thermal comfort in daily use face masks is essential in many situations. Here, radiative thermal management is introduced into face masks to elevate the user comfort. An interlayered poly(lactic acid) (PLA) micro/nanofibrous filter effectively captures PM0.3 (99.69%) with minimal pressure drop (49 Pa). Thermal regulation is accomplished by controlling the mid-infrared (MIR) emissivity of the face mask's outer surface. Cooling face masks feature cotton nonwovens with high MIR emissivity (90.7%) for heat dissipation, while warming face masks utilize perforated Al/PE films with minimal MIR emissivity (10.7%) for warmth retention. Skin temperature measurements indicate that the skin covered by the cooling face mask could be 1.1 °C lower than that covered by the 3M face mask, while the skin covered by the warming face mask could be 1.3 °C higher than that covered by the 3M face mask.
RESUMEN
Interfacial solar vapor generation holds great promise for alleviating the global freshwater crisis, but its real-world application is limited by the efficiently choppy water evaporation and industrial production capability. Herein, a self-floating solar evaporator with an underwater aerophilic surface is innovatively fabricated by weaving core-shell yarns via mature weaving techniques. The core-shell yarns possess capillary water channels in the hydrophilic cotton core and can trap air in the hydrophobic electrospinning nanofiber shell when submerged underwater, simultaneously realizing controllable water supplies, stable self-flotation, and great thermal insulation. Consequently, the self-floating solar evaporator achieves an evaporation rate of 2.26 kg m-2 h-1 under 1 sun irradiation, with a reduced heat conduction of 70.18 W m-2. Additionally, for the first time, a solar evaporator can operate continuously in water with varying waveforms and intensities over 24 h, exhibiting an outdoor cumulative evaporation rate of 14.17 kg m-2 day-1.
RESUMEN
Room-temperature phase change materials (RTPCMs) exhibit promise to address challenges in thermal energy storage and release, greatly aiding in numerous domains of human existence and productivity. The conventional RTPCMs undergo inevitable volume expansion, structural collapse, and diffusion of active ingredients while maintaining desirable phase change enthalpy and ideal phase change temperature. Here, a sol-gel 1D-induced growth approach is presented to fabricate meta nanofibers (Meta-NFs) comprised of vanadium dioxide with monoclinic crystal structure, and further achieve the editable phase change temperature from 68 to 37 °C through W-doping, which allowed for tailored length variation of the zigzag V-V bond. Subsequently, Meta-NFs are assembled into 3D aerogels with self-standing architecture, thereby enabling the independent use of the RTPCMs. The obtained metamaterials demonstrate not only the temperature-editing solid-solid phase transition, but also the stiffness of the ceramic matrix, exhibiting the thermal energy control capability at room temperature (37 °C), thermal insulation properties, temperature resistance, and flame retardancy. The effective creation of these fascinating metamaterials might offer new insights for next-generation and self-standing solid-solid RTPCMs.
RESUMEN
Extreme environments can cause severe harm to human health, and even threaten life safety. Lightweight, breathable clothing with multi-protective functions would be of great application value. However, integrating multi-protective functions into nanofibers in a facile way remains a great challenge. Here, a one-step co-electrospinning-electrospray strategy is developed to fabricate a superhydrophobic multi-protective membrane (S-MPM). The water contact angle of S-MPM can reach up to 164.3°. More importantly, S-MPM can resist the skin temperature drop (11.2 °C) or increase (17.2 °C) caused by 0 °C cold or 70 °C hot compared with pure electrospun membrane. In the cold climate (-5 °C), the anti-icing time of the S-MPM is extended by 2.52 times, while the deicing time is only 1.45 s due to the great photothermal effect. In a fire disaster situation, the total heat release and peak heat release rate values of flame retarded S-MPM drop sharply by 24.2% and 69.3%, respectively. The S-MPM will serve as the last line of defense for the human body and has the potential to trigger a revolution in the practical application of next-generation functional clothing.
Asunto(s)
Ropa de Protección , Temperatura Cutánea , Humanos , Frío , Calor , Ambientes ExtremosRESUMEN
With the rapid development of electronic industry, it's pressing to develop multifunctional electromagnetic interference (EMI) shielding materials to ensure the stable operation of electronic devices. Herein, multilayered flexible PEG@PAN/MXene (Ti3C2Tx)/PVDF@SiO2 (PMF) composite film has been constructed from the level of microstructure design via coaxial electrospinning, coating spraying, and uniaxial electrospinning strategies. Benefiting from the effective encapsulation for PEG and high conductivity of MXene coating, PEG@PAN/MXene composite film with MXene coating loading density of 0.70 mg cm-2 exhibits high thermal energy storage density of 120.77 J g-1 and great EMI shielding performance (EMI SE of 34.409 dB and SSE of 49.086 dB cm3 g-1) in X-band (8-12 GHz). Therefore, this advanced composite film can not only help electronic devices prevent the influence of electromagnetic pollution in the X-band but also play an important role in electronic device thermal management. Additionally, the deposition of nano PVDF@SiO2 fibers (289 ± 128 nm) endowed the PMF composite film with great hydrophobic properties (water contact angle of 126.5°) to ensure the stable working of hydrophilic MXene coating, thereby breaks the limitation of humid application environments. The finding paves a new way for the development of novel multifunctional EMI shielding composite films for electronic devices.
RESUMEN
Interface design has enormous potential for the enhancement of interfacial polarization and microwave absorption properties. However, the construction of interfaces is always limited in components of a single dimension. Developing systematic strategies to customize multidimensional interfaces and fully utilize advantages of low-dimensional materials remains challenging. Two-dimensional transition metal dichalcogenides (TMDCs) have garnered significant attention owing to their distinctive electrical conductivity and exceptional interfacial effects. In this study, a series of hollow TMDCs@C fibers are synthesized via sacrificial template of CdS and confined growth of TMDCs embedded in the fibers. The complex permittivity of the hollow TMDCs@C fibers can be adjusted by tuning the content of CdS templates. Importantly, the multidimensional interfaces of the fibers contribute to elevating the microwave absorption performance. Among the hollow TMDCs@C fibers, the minimum reflection loss (RLmin) of the hollow MoS2@C fibers can reach -52.0 dB at the thickness of 2.5 mm, with a broad effective absorption bandwidth of 4.56 GHz at 2.0 mm. This work establishes an alternative approach for constructing multidimensional coupling interfaces and optimizing TMDCs as microwave absorption materials.
RESUMEN
Solid-state lithium batteries (SSLBs) are regarded as next-generation energy storage devices because of their advantages in terms of safety and energy density. However, the poor interfacial compatibility and low ionic conductivity seriously hinder their development. Electrospinning is considered as a promising method for fabricating solid-state electrolytes (SSEs) with controllable nanofiber structures, scalability, and cost-effectiveness. Numerous efforts are dedicated to electrospinning SSEs with high ionic conductivity and strong interfacial compatibility, but a comprehensive summary is lacking. Here, the history of electrospinning SSEs is overeviewed and introduce the electrospinning mechanism, followed by the manipulation of electrospun nanofibers and their utilization in SSEs, as well as various methods to improve the ionic conductivity of SSEs. Finally, new perspectives aimed at enhancing the performance of SSEs membranes and facilitating their industrialization are proposed. This review aims to provide a comprehensive overview and future perspective on electrospinning technology in SSEs, with the goal of guiding the further development of SSLBs.
RESUMEN
Fluorescent probes are an indispensable tool in the realm of bioimaging technologies, providing valuable insights into the assessment of biomaterial integrity and structural properties. However, incorporating fluorophores into scaffolds made from melt electrowriting (MEW) poses a challenge due to the sustained, elevated temperatures that this processing technique requires. In this context, [n]cycloparaphenylenes ([n]CPPs) serve as excellent fluorophores for MEW processing with the additional benefit of customizable emissions profiles with the same excitation wavelength. Three fluorescent blends are used with distinct [n]CPPs with emission wavelengths of either 466, 494, or 533 nm, identifying 0.01 wt% as the preferred concentration. It is discovered that [n]CPPs disperse well within poly(ε-caprolactone) (PCL) and maintain their fluorescence even after a week of continuous heating at 80 °C. The [n]CPP-PCL blends show no cytotoxicity and support counterstaining with commonly used DAPI (Ex/Em: 359 nm/457 nm), rhodamine- (Ex/Em: 542/565 nm), and fluorescein-tagged (Ex/Em: 490/515 nm) phalloidin stains. Using different color [n]CPP-PCL blends, different MEW fibers are sequentially deposited into a semi-woven scaffold and onto a solution electrospun membrane composed of [8]CPP-PCL as a contrasting substrate for the [10]CPP-PCL MEW fibers. In general, [n]CPPs are potent fluorophores for MEW, providing new imaging options for this technology.
RESUMEN
Polyacrylonitrile/Boric acid/Melamine/the delaminated BN nanosheets electrospun fiber membrane (PB3N1BN) with excellent mechanical property, high thermal stability, superior flame-retardant performance, and good wettability are fabricated by electrospinning PAN/DMF/H3BO3/C3H6N6/ the delaminated BN nanosheets (BNNSs) homogeneous viscous suspension and followed by a heating treatment. BNNSs are obtained by delaminating the bulk h-BN in isopropyl alcohol (IPA) with an assistance of Polyvinylpyrrolidone (PVP). Benefiting from the cross-linked pore structure and high-temperature stability of BNNSs, PB3N1BN electrospun fiber membrane delivers high thermal dimensional stability (almost no size contraction at 200 °C), excellent mechanical property (19.1 MPa), good electrolyte wettability (contact angle about 0°), and excellent flame retardancy (minimum total heat release of 3.2 MJ m-2). Moreover, the assembled LiFePO4/PB3N1BN/Li asymmetrical battery using LiFePO4 as the cathode and Li as the anode has a high capacity (169 mAh g-1 at 0.5 C), exceptional rate capability (129 mAh g-1 at 5 C), the prominent cycling stability without obvious decay after 400 cycles, and a good discharge capacity of 152 mAh g-1 at a high temperature of 80 °C. This work offers a new structural design strategy toward separators with excellent mechanical performance, good wettability, and high thermal stability for lithium-ion batteries.
RESUMEN
Diabetic chronic wounds pose significant clinical challenges due to their characteristic features of impaired extracellular matrix (ECM) function, diminished angiogenesis, chronic inflammation, and increased susceptibility to infection. To tackle these challenges and provide a comprehensive therapeutic approach for diabetic wounds, the first coaxial electrospun nanocomposite membrane is developed that incorporates multifunctional copper peroxide nanoparticles (n-CuO2 ). The membrane's nanofiber possesses a unique "core/sheath" structure consisting of n-CuO2 +PVP (Polyvinylpyrrolidone)/PCL (Polycaprolactone) composite sheath and a PCL core. When exposed to the wound's moist environment, PVP within the sheath gradually disintegrates, releasing the embedded n-CuO2 . Under a weakly acidic microenvironment (typically diabetic and infected wounds), n-CuO2 decomposes to release H2 O2 and Cu2+ ions and subsequently produce ·OH through chemodynamic reactions. This enables the anti-bacterial activity mediated by reactive oxygen species (ROS), suppressing the inflammation while enhancing angiogenesis. At the same time, the dissolution of PVP unveils unique nano-grooved surface patterns on the nanofibers, providing desirable cell-guiding function required for accelerated skin regeneration. Through meticulous material selection and design, this study pioneers the development of functional nanocomposites for multi-modal wound therapy, which holds great promise in guiding the path to healing for diabetic wounds.
Asunto(s)
Diabetes Mellitus , Nanocompuestos , Nanofibras , Humanos , Cicatrización de Heridas , Piel/lesiones , Nanocompuestos/química , Nanofibras/química , InflamaciónRESUMEN
Solar-driven interfacial desalination is widely considered to be a promising technology to address the global water crisis. This study proposes a novel electrospun nanofiber-based all-in-one vertically interfacial solar evaporator endowed with a high steam generation rate, steady omnidirectional evaporation, and enduring ultrahigh-salinity brine desalination. In particular, the electrospun nanofiber is collected into the tubular structure, followed by spraying with a dense crosslinked poly(vinyl alcohol) film, which renders them sufficiently strong for the preparation of a vertically array evaporator. The integrated evaporator made an individual capillary as a unit to form multiple thermal localization interfaces and steam dissipation channels, realizing zone heating of water. Thus a high steam generation rate exceeding 4.0 kg m-2 h-1 in pure water is demonstrated even under omnidirectional sunlight, and outperforms existing evaporators. Moreover, salt ions in the photothermal layer can be effectively transported to the water in capillaries and subsequently exchanged with the bulk water due to the strong action of capillary force, which ensures an ultrahigh desalination rate (≈12.5 kg m-2 h-1 under 3 sun) in 25 wt% concentration brine over 300 min. As such, this work provides a meaningful roadmap for the development of state-of-the-art solar-driven interfacial desalination.
RESUMEN
Futuristic wearable electronics desperately need power sources with similar flexibility and durability. In this regard, the authors, therefore, propose a scalable PAN-PMMA blend-derived electrospinning protocol to fabricate free-standing electrodes comprised of cobalt hexacyanoferrate nanocube cathode and tin metal organic framework-derived nanosphere anode, respectively, for flexible sodium-ion batteries. The resulting unique inter-networked nanofiber mesh offers several advantages such as robust structural stability towards repeated bending and twisting stresses along with appreciable electronic/ionic conductivity retention without any additional post-synthesis processing. The fabricated flexible sodium ion full cells deliver a high working voltage of 3.0 V, an energy density of 273 Wh·kg-1 , and a power density of 2.36 kW·kg-1 . The full cells retain up to 86.73% of the initial capacity after 1000 cycles at a 1.0 C rate. After intensive flexibility tests, the full cells also retain 78.26% and 90.78% of the initial capacity after 1000 bending and twisting cycles (5 mm radius bending and 40o axial twisting), respectively. This work proves that the proposed approach can also be employed to construct similar robust, free-standing nanofiber mesh-based electrodes for mass-producible, ultra-flexible, and durable sodium ion full cells with commercial viability.
RESUMEN
The shuttle effect of lithium polysulfides (LiPSs) severely hinders the development and commercialization of lithium-sulfur batteries, and the design of high-conductive carbon fiber-host material has become a key solution to suppress the shuttle effect. In this work, a unique Co/CoN-carbon nanocages@TiO2-carbon nanotubes structure (NC@TiO2-CNTs) is constructed using an electrospinning and nitriding process. Lithium-sulfur batteries using NC@TiO2-CNTs as cathode host materials exhibit high sulfur utilization (1527 mAh g-1 at 0.2 C) and can still maintain a discharge capacity of 663 mAh g-1 at a high current density of 5 C, and the capacity loss is only 0.056% per cycle during 500 cycles at 1 C. It is worth noting that even under extreme conditions (sulfur-loading = 90%, surface-loading = 5.0 mg cm-2 (S), and E/S = 6.63 µL mg-1), the lithium-sulfur batteries can still provide a reversible capacity of 4 mAh cm-2. Throughdensity functional theory calculations, it has been found that the Co/CoN heterostructures can adsorb and catalyze LiPSs conversion effectively. Simultaneously, the TiO2 can adsorb LiPSs and transfer Li+ selectively, achieving dual confinement for the shuttle effect of LiPSs (nanocages and nanotubes). The new findings provide a new performance enhancement strategy for the commercialization of lithium-sulfur batteries.
RESUMEN
Triboelectric nanogenerators (TENGs) have emerged as a promising technology for harvesting mechanical energy from the ambient environment. However, developing tribopositive materials with strong piezoelectric effects and high electron-donating ability still remains a challenge. Herein, poly(ethylene glycol) monomethyl ether (mPEG) to soft poly(lactic acid) (PLA) is adopted, then PLA/mPEG nanofibers are fabricated under electrospinning and used as the tribopositive material for fabricating robust power density TENGs. The crystallinity and dynamic mechanical properties of PLA/mPEG nanofibers are investigated. The results revealed that the incorporation of mPEG provided an effective approach to elevate the electron-donating ability and charge transfer efficiency in PLA. The PLA/mPEG-based TENGs achieved a high open-circuit voltage of 342.8 V, a short-circuit current of 38.5 µA, and a maximum power density of 116.21 W m-2 over a 2 cm2 contact area at an external load of 106 Ω, respectively. Strikingly, excellent stability and durability are demonstrated after continuous cycles up to 104 cycles. Noteworthy, the TENGs are explored for self-powered sensing applications, with seven TENG units integrated to act as self-powered sensors playing music through buzzers when pressed by fingers. Eventually, this work provides new insights into tuning the structures and properties of electrospun polymers to reinforce the TENG output and self-powered systems.
RESUMEN
Traditional fluorescent anti-counterfeiting labels based on "on-off" fluorescence can be easily cloned. It is important to explore advanced anti-counterfeiting fluorescent labels with high-level security. Here, a pioneering ion species- and ion concentration-dependent anti-counterfeiting technique is developed. By successive loading Cu2+ -sensitive yellow emitted carbon dots (Y-CDs) and Cu2+ non-sensitive blue emitted carbon dots (B-CDs) into metal-organic frameworks (MOFs) and followed by electrospinning, the B&Y-CDs@MOF-nanofibrous films are prepared. The results show that the use of MOF not only avoids the fluorescence quenching of CDs but also improves the fluorescence stability. The fluorescence Cu2+ -sensitivity of the CDs@MOF-nanofibrous films can be regulated by polymer coating or lamination. The fluorescent label consisting of different Cu2+ -sensitivity films will show Cu2+ concentration-dependent decryption information. Only at a specific ion species and concentration (Cu2+ solution of 40-90 µm), the true information can be read out. Less or more concentration (<40 or >90 µm) will lead to false information. The identification of the real information depends on both the species and the concentration. After Cu2+ treatment, the fluorescence of the label can be recovered by ethylenediaminetetraacetic acid disodium (EDTA-2Na) for further recycling. This work will open up a new door for designing high-level fluorescent anti-counterfeiting labels.
RESUMEN
Rational designing electrocatalysts is of great significance for realizing high-efficiency H2 production in the water splitting process. Generally, reducing the usage of precious metals and developing low-potential nucleophiles oxidation reaction to replace anodic oxygen evolution reaction (OER) are efficient strategies to promote H2 generation. Here, NiS-coated nickel-carbon nanofibers (NiS@Ni-CNFs) are prepared for low-content Pt deposition (Pt-NiS@Ni-CNFs) to attain the alkaline HER catalyst. Due to the reconfiguration of NiS phase and synergistic effect between Pt and nickel sulfides, the Pt-NiS@Ni-CNFs catalyst shows a high mass activity of 2.74-fold of benchmark Pt/C sample. In addition, the NiS@Ni-CNFs catalyst performs a superior urea oxidation reaction (UOR) activity with the potential of 1.366 V versus reversible hydrogen electrode (RHE) at 10 mA cm-2 , which demonstrates the great potential in the replacement of OER. Thus, a urea-assisted water splitting electrolyzer of Pt-NiS@Ni-CNFs (cathode)||NiS@Ni-CNFs (anode) is constructed to exhibit small voltages of 1.44 and 1.65 V to reach 10 and 100 mA cm-2 , which is much lower than its overall water splitting process, and presents a 6.5-fold hydrogen production rate enhancement. This work offers great opportunity to design new catalysts toward urea-assisted water splitting with significantly promoted hydrogen productivity and reduced energy consumption.
RESUMEN
For materials with coexisting phases, the transition from a random to an ordered distribution of materials often generates new mechanisms. Although the magnetic confinement effect has improved the electromagnetic (EM) performance, the transition from random to ordered magnetic confinement positions remains a synthetic challenge, and the underlying mechanisms are still unclear. Herein, precise control of magnetic nanoparticles is achieved through a spatial confinement growth strategy, preparing five different modalities of magnetic confined carbon fiber materials, effectively inhibiting magnetic agglomeration. Systematic studies have shown that the magnetic confinement network can refine CoNi NPs size and enhance strong magnetic coupling interactions. Compared to CoNi@HCNFs on the hollow carbon fibers (HCNFs) outer surface, HCNFs@CoNi constructed on the inner surface induce stronger spatial charge polarization relaxation at the interface and exhibit stronger magnetic coupling interactions at the inner surface due to the high-density magnetic coupling units at the micro/nanoscale, thereby respectively enhancing dielectric and magnetic losses. Remarkably, they achieve a minimum reflection loss (RLmin) of -64.54 dB and an absorption bandwidth of 5.60 GHz at a thickness of 1.77 mm. This work reveals the microscale mechanism of magnetic confinement-induced different polarization relaxation and magnetic response, providing a new strategy for designing magnetic materials.