Spatio-temporal distribution of sea surface chlorophyll-a in coral reefs of the South China Sea over the past decade based on Landsat-8 Operational Land Images.

The concentration of chlorophyll-a (Chl-a) in seawater reflects phytoplankton growth and water eutrophication, which are usually assessed for evaluation of primary productivity and carbon source/sink of coral reefs. However, the precise delineation of Chl-a concentration in coral reefs remains a challenge when ocean satellites with low spatial resolution are utilized. In this study, a remote sensing inversion model for Chl-a was developed in fringing reefs (R2 = 0.76, RMSE =0.41 µg/L, MRE = 14 %) and atolls (R2 = 0.79, RMSE =0.02 µg/L, MRE = 8 %), utilizing reflectance data from the sensitive band of the Landsat-8 Operational Land Imagers (OLI) with a spatial resolution of 30 m. The aforementioned model was utilized to invert high-resolution distribution maps of Chl-a concentration in six major coral reef regions of the South China Sea from 2013 to 2022 and subsequently used to analyze the variations in Chl-a concentration and its influencing factors. The results indicate a Chl-a concentration gradient among coral reefs Daya Bay, Weizhou Island, Luhuitou, Xuwen, Huangyan Island, and Xisha Island in that order. The Chl-a concentration in coral reefs exhibited an overall increasing trend, with significant seasonal fluctuations, characterized by higher concentrations during winter and spring and lower concentrations during summer and autumn. The concentration of Chl-a in coral reefs was positively correlated with the average wind speed.

Effect of the prism-interprisms three-dimension spatial microstructure on the enamel bond strength.

The prism-interprisms level of the enamel hierarchical microstructure is the largest degree of structural variation and most sophisticated structural adaptation. We studied the effect of the prism-interprisms three-dimension spatial microstructure on the enamel bond strength. We prepared 11 groups of enamel segments: longitudinally sectioned segments with or without a 45-degree bevel (group = 2), horizontally sectioned segments with or without a 45-degree bevel of three regions (the incisal, middle, and cervical) (group = 6), and tangential (labial) sectioned segments of three regions (the incisal, middle, and cervical) (group = 3). The finished surface of each segment was observed by scanning electric microscopy (SEM) before treatment with four self-etch adhesive systems and applied with four corresponding composite resins. Resin-bonded enamel samples were prepared in beams for microtensile bond strength (MTBS) tests. The results were analyzed with a three-way ANOVA followed by Tukey's post-hoc HSD multiple comparisons procedure. SEM observations revealed complex arrangements of prisms and interprisms. MTBS measurement showed that the longitudinally sectioned group had the lowest value, without significant differences between the groups with or without 45-degree bevel. Combining SEM observations and MTBS measurements, the prism-interprisms microstructure varied with the incisor regions, and different prism-interprisms microstructures allowed diverse sectioned surfaces, which could affect the enamel bonding.

High-efficiency, high-repetition-rate cavity-dumped Q-switched Yb:YAG thin-disk laser based on a 72-pass pump module.

We demonstrated a compact cavity-dumped Q-switched Yb:YAG laser based on a 72-pass pump module. A highly stable nanosecond pulse laser with a duration of 18.38 ns was achieved at a repetition rate of 100 kHz, which is pumped by multimode laser diode stacks at 969 nm. The average output power of more than 150 W is delivered in a good output beam characterized by M2 = 1.53. The result shows that the pulse duration derived from simulation agrees well with the one retrieved from the experimental measurements. To the best of our knowledge, the 43.5% optical-optical efficiency is the highest reported to date from a cavity-dumped Q-switched Yb:YAG TDL (thin-disk laser).

Resonators with a continuously variable output coupling rate to enhance output performance of Yb:YAG thin-disk lasers.

Beam quality and average output power are two long-sought parameters of continuous-wave lasers. The operating characteristics of a Yb:YAG thin-disk laser based on a 72-pass pump module using output couplers with continuously variable coupling rates are reported. When the pump power is 450 W, the average power of more than 210 W is obtained, and the corresponding optical-optical efficiency is about 46.67%. The output beam is near diffraction limited with M2=1.20 and 1.18 on the horizontal and vertical directions respectively. The thin-disk laser maintains the beam quality near diffraction limited within the whole pump power range by continuously changing the coupling rate of the output coupler (the combination of thin film polarizer and quarter-wave plate) according to the incident pump power. The experimental results show that by continuously changing the coupling rate, combined with the dynamic change of thermal lens effect, the laser beam quality factor M2 can be reduced from 2.0 to 1.2, and the beam quality can be improved by about 40%. The improvement of and increase of average output power confirm that resonators with continuously variable coupling rate are a promising method for enhancing output performance of thin-disk lasers.