Defect Passivation and Crystallization Regulation for Efficient and Stable Formamidinium Lead Iodide Solar Cells with Multifunctional Amidino Additive.

Amidino-based additives show great potential in high-performance perovskite solar cells (PSCs). However, the role of different functional groups in amidino-based additives have not been well elucidated. Herein, two multifunctional amidino additives 4-amidinobenzoic acid hydrochloride (ABAc) and 4-amidinobenzamide hydrochloride (ABAm) are employed to improve the film quality of formamidinium lead iodide (FAPbI3) perovskites. Compared with ABAc, the amide group imparts ABAm with larger dipole moment and thus stronger interactions with the perovskite components, i.e., the hydrogen bonds between N…H and I- anion and coordination bonds between C = O and Pb2+ cation. It strengthens the passivation effect of iodine vacancy defect and slows down the crystallization process of α-FAPbI3, resulting in the significantly reduced non-radiative recombination, long carrier lifetime of 1.7 µs, uniformly large crystalline grains, and enhances hydrophobicity. Profiting from the improved film quality, the ABAm-treated PSC achieves a high efficiency of 24.60%, and maintains 93% of the initial efficiency after storage in ambient environment for 1200 hours. This work provides new insights for rational design of multifunctional additives regarding of defect passivation and crystallization control toward highly efficient and stable PSCs.

An Intrinsic Photothermal Supramolecular Hydrogel with Robust Mechanical Strength and NIR-Responsive Shape Memory.

Near-infrared (NIR)-triggered shape memory hydrogels with promising mechanical strength hold immense potential in the field of biomedical applications and soft actuators. However, the optical and mechanical properties of currently reported hydrogels usually suffer from limited solubility and dispersion of commonly used photothermal additives in hydrogels, thus restricting their practical implementations. Here,, a set of NIR-responsive shape memory hydrogels synthesized by polyaddition of diisocyanate-terminated poly(ethylene glycol), imidazolidinyl urea (IU), and p-benzoquinone dioxime (BQDO) is reported. The introduction of IU, a hydrogen bond reinforcing factor, significantly enhances the mechanical properties of the hydrogels, allowing for their tunable ranges of the ultimate tensile strength (0.4-2.5 MPa), elongation at break (210-450%), and Young's modulus (190-850 kPa). The unique hydrogels exhibit an intrinsic photothermal effect because of the covalently incorporated photothermal moiety (BQDO), and the photothermal supramolecular hydrogel shows controllable shape memory capabilities characterized by rapid recovery speed and high recovery ratio (>90%). This design provides new possibilities for applying shape memory hydrogels in the field of soft actuators.

Flexible Indoor Perovskite Solar Cells by In Situ Bottom-Up Crystallization Modulation and Interfacial Passivation.

A robust perovskite-buried interface is pivotal for achieving high-performance flexible indoor photovoltaics as it significantly influences charge transport and extraction efficiency. Herein, a molecular bridge strategy is introduced utilizing sodium 2-cyanoacetate (SZC) additive at the perovskite-buried interface to simultaneously achieve in situ passivation of interfacial defects and bottom-up crystallization modulation, resulting in high-performance flexible indoor photovoltaic applications. Supported by both theoretical calculations and experimental evidences, it illustrates how SZCs serve as molecular bridges, establishing robust bonds between SnO2 transport layer and perovskite, mitigating oxygen vacancy defects and under-coordinated Pb defects at interface during flexible fabrication. This, in turn, enhances interfacial energy level alignment and facilitates efficient carrier transport. Moreover, this in situ investigation of perovskite crystallization dynamics reveals bottom-up crystallization modulation, extending perovskite growth at the buried interface and influencing subsequent surface recrystallization. This results in larger crystalline grains and improved lattice strain of the perovskite during flexible fabrication. Finally, the optimized flexible solar cells achieve an impressive efficiency exceeding 41% at 1000 lux, with a fill factor as high as 84.32%. The concept of the molecular bridge represents a significant advancement in enhancing the performance of perovskite-based flexible indoor photovoltaics for the upcoming era of Internet of Things (IoT).

Defect Passivation Refinement in Perovskite Photovoltaics: Achieving Efficiency over 45% under Low-Light and Low-Temperature Dual Extreme Conditions.

Perovskite photovoltaics have emerged as the most promising candidates for next-generation light-to-electricity technology. However, their practical application still suffers from energy loss induced by intrinsic defects within the perovskite lattice. Here, a refined defect passivation in perovskite films is designed, which shows a multi-interaction mechanism between the perovskite and passivator. Interestingly, a shift of molecular bonding is observed upon cooling down the film, leading to a stronger passivation of iodine/formamidine vacancies. Such mechanism on device under low-light and low-temperature conditions is further leveraged and a record efficiency over 45% with durable ambient stability (T90 > 4000 h) is obtained. The pioneer application of perovskite solar cells in above dual extreme conditions in this work reveals the key principles of designing functional groups for the passivators, and also demonstrates the capability of perovskites for diverse terrestrial energy conversion applications in demanding environments such as polar regions and outer space.

Highly Stretchable Conjugated Polymer/Elastomer Blend Films with Sandwich Structure.

The physical blending of high-mobility conjugated polymers with ductile elastomers provides a simple way to realize high-performance stretchable films. However, how to control the morphology of the conjugated polymer and elastomer blend film and its response to mechanical fracture processes during stretching are not well understood. Herein, a sandwich structure is constructed in the blend film based on a conjugated polymer poly[(5-fluoro-2,1,3-benzothiadiazole-4,7-diyl)(4,4-dihexadecyl-4H-cyclopenta[2,1-b:3,4-b″]dithiophene-2,6-diyl)(6-fluoro-2,1,3-benzothiadiazole-4,7-diyl)(4,4-dihexadecyl-4H-cyclopenta[2,1-b:3,4-b″]dithiophene-2,6-diyl)] (PCDTFBT) and an elastomer polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS). The sandwich structure is composed of a PCDTFBT:SEBS mixed layer laminated with a PCDTFBT-rich layer at both the top and bottom surfaces. During stretching, the external strain energy can be effectively dissipated by the deformation of the crystalline PCDTFBT domains and amorphous SEBS phases and the recrystallization of the PCDTFBT chains. This endows the blend film with excellent ductility, with a large crack onset strain exceeding 1100%, and minimized the electrical degradation of the blend film at a large strain. This study indicates that the electrical and mechanical performance of conjugated polymer/elastomer blend films can be improved by manipulating their microstructure.

Aligned Conjugated Polymer Nanofiber Networks in an Elastomer Matrix for High-Performance Printed Stretchable Electronics.

Conjugated polymer films are promising in wearable X-ray detection. However, achieving optimal film microstructure possessing good electrical and detection performance under large deformation via scalable printing remains challenging. Herein, we report bar-coated high-performance stretchable films based on a conjugated polymer P(TDPP-Se) and elastomer SEBS blend by optimizing the solution-processing conditions. The moderate preaggregation in solution and prolonged growth dynamics from a solvent mixture with limited dissolving capacity is critical to forming aligned P(TDPP-Se) chains/crystalline nanofibers in the SEBS phase with enhanced π-π stacking for charge transport and stress dissipation. The film shows a large elongation at break of >400% and high mobilities of 5.29 cm2 V-1 s-1 at 0% strain and 1.66 cm2 V-1 s-1 over 500 stretch-release cycles at 50% strain, enabling good X-ray imaging with a high sensitivity of 1501.52 µC Gyair-1 cm-2. Our work provides a morphology control strategy toward high-performance conjugated polymer film-based stretchable electronics.

Green-Solvent Processed Blade-Coating Organic Solar Cells with an Efficiency Approaching 19% Enabled by Alkyl-Tailored Acceptors.

Power-conversion-efficiencies (PCEs) of organic solar cells (OSCs) in laboratory, normally processed by spin-coating technology with toxic halogenated solvents, have reached over 19%. However, there is usually a marked PCE drop when the blade-coating and/or green-solvents toward large-scale printing are used instead, which hampers the practical development of OSCs. Here, a new series of N-alkyl-tailored small molecule acceptors named YR-SeNF with a same molecular main backbone are developed by combining selenium-fused central-core and naphthalene-fused end-group. Thanks to the N-alkyl engineering, NIR-absorbing YR-SeNF series show different crystallinity, packing patterns, and miscibility with polymeric donor. The studies exhibit that the molecular packing, crystallinity, and vertical distribution of active layer morphologies are well optimized by introducing newly designed guest acceptor associated with tailored N-alkyl chains, providing the improved charge transfer dynamics and stability for the PM6:L8-BO:YR-SeNF-based OSCs. As a result, a record-high PCE approaching 19% is achieved in the blade-coating OSCs fabricated from a green-solvent o-xylene with high-boiling point. Notably, ternary OSCs offer robust operating stability under maximum-power-point tracking and well-keep > 80% of the initial PCEs for even over 400 h. Our alkyl-tailored guest acceptor strategy provides a unique approach to develop green-solvent and blade-coating processed high-efficiency and operating stable OSCs, which paves a way for industrial development.

Interfacial Engineering for Efficient Low-Temperature Flexible Perovskite Solar Cells.

Photovoltaic technology with low weight, high specific power in cold environments, and compatibility with flexible fabrication is highly desired for near-space vehicles and polar region applications. Herein, we demonstrate efficient low-temperature flexible perovskite solar cells by improving the interfacial contact between electron-transport layer (ETL) and perovskite layer. We find that the adsorbed oxygen active sites and oxygen vacancies of flexible tin oxide (SnO2 ) ETL layer can be effectively decreased by incorporating a trace amount of titanium tetrachloride (TiCl4 ). The effective defects elimination at the interfacial increases the electron mobility of flexible SnO2 layer, regulates band alignment at the perovskite/SnO2 interface, induces larger perovskite crystal growth, and improves charge collection efficiency in a complete solar cell. Correspondingly, the improved interfacial contact transforms into high-performance solar cells under one-sun illumination (AM 1.5G) with efficiencies up to 23.7 % at 218 K, which might open up a new era of application of this emerging flexible photovoltaic technology to low-temperature environments such as near-space and polar regions.

In Situ Self-Elimination of Defects via Controlled Perovskite Crystallization Dynamics for High-Performance Solar Cells.

Understanding and controlling crystallization is crucial for high-quality perovskite films and efficient solar cells. Herein, the issue of defects in formamidinium lead iodide (FAPbI3 ) formation is addressed, focusing on the role of intermediates. A comprehensive picture of structural and carrier evolution during crystallization is demonstrated using in situ grazing-incidence wide-angle X-ray scattering, ultraviolet-visible spectroscopy and photoluminescence spectroscopy. Three crystallization stages are identified: precursors to the δ-FAPbI3 intermediate, then to α-FAPbI3 , where defects spontaneously emerge. A hydrogen-sulfate-based ionic liquid additive is found to enable the phase-conversion pathway of precursors → solvated intermediates → α-FAPbI3 , during which the spontaneous generation of δ-FAPbI3 can be effectively circumvented. This additive extends the initial growth kinetics and facilitates solvent-FA+ ion exchange, which results in the self-elimination of defects during crystallization. Therefore, the improved crystallization dynamics lead to larger grain sizes and fewer defects within thin films. Ultimately, the improved perovskite crystallization dynamics enable high-performance solar cells, achieving impressive efficiencies of 25.14% at 300 K and 26.12% at 240 K. This breakthrough might open up a new era of application for the emerging perovskite photovoltaic technology to low-temperature environments such as near-space and polar regions.

Crystallization Control for Ambient Printed FA-Based Lead Triiodide Perovskite Solar Cells.

Upscalable printing of high-performance and stable perovskite solar cells (PSCs) is highly desired for commercialization. However, the efficiencies of printed PSCs lag behind those of their lab-scale spin-coated counterparts owing to the lack of systematic understanding and control over perovskite crystallization dynamics. Here, the controlled crystallization dynamics achieved using an additive 1-butylpyridine tetrafluoroborate (BPyBF4 ) for high-quality ambient printed α-formamidinium lead triiodide (FAPbI3 ) perovskite films are reported. Using in situ grazing-incidence wide-angle X-ray scattering and optical diagnostics, the spontaneous formation of α-FAPbI3 from precursors during printing without the involvement of  Î´-FAPbI3 is demonstrated. The addition of BPyBF4 delays the crystallization onset of α-FAPbI3 , enhances the conversion from sol-gel to perovskite, and reduces stacking defects during printing. Therefore, the altered crystallization results in fewer voids, larger grains, and less trap-induced recombination loss within printed films. The printed PSCs yield high power conversion efficiencies of 23.50% and 21.60% for a 0.09 cm-2 area device and a 5 cm × 5 cm-area module, respectively. Improved device stability is further demonstrated, i.e., approximately 94% of the initial efficiency is retained for over 2400 h under ambient conditions without encapsulation. This study provides an effective crystallization control method for the ambient printing manufacture of large-area high-performance PSCs.

One-stone-for-two-birds strategy to attain beyond 25% perovskite solar cells.

Even though the perovskite solar cell has been so popular for its skyrocketing power conversion efficiency, its further development is still roadblocked by its overall performance, in particular long-term stability, large-area fabrication and stable module efficiency. In essence, the soft component and ionic-electronic nature of metal halide perovskites usually chaperonage large number of anion vacancy defects that act as recombination centers to decrease both the photovoltaic efficiency and operational stability. Herein, we report a one-stone-for-two-birds strategy in which both anion-fixation and associated undercoordinated-Pb passivation are in situ achieved during crystallization by using a single amidino-based ligand, namely 3-amidinopyridine, for metal-halide perovskite to overcome above challenges. The resultant devices attain a power conversion efficiency as high as 25.3% (certified at 24.8%) with substantially improved stability. Moreover, the device without encapsulation retained 92% of its initial efficiency after 5000 h exposure in ambient and the device with encapsulation retained 95% of its initial efficiency after >500 h working at the maximum power point under continuous light irradiation in ambient. It is expected this one-stone-for-two-birds strategy will benefit large-area fabrication that desires for simplicity.

Blending Donors with Different Molecular Weights: An Efficient Strategy to Resolve the Conflict between Coherence Length and Intermixed Phase in Polymer/Nonfullerene Solar Cells.

Long coherence lengths (CLs) of crystals and proper intermixed phase amount guarantee charge transport and exciton dissociate efficiently, which is crucial for organic solar cells (OSCs) to achieve high device performance. However, extending CLs usually reduces the intermixed phase, leading to an insufficient interface for exciton dissociation. Herein, a strategy using a binary polymer with different molecular weights as donor is employed, that is, poly(3-hexylthiophene-2,5-diyl) (P3HT) with high (P3HT-H) and low (P3HT-L) molecular weight are blended as donor, and (5Z,5'Z)-5,5'-(((4,4,9,9-tetraoctyl-4,9-dihydro-s-indaceno[1,2-b:5,6-b']dithiophene-2,7-diyl)bis(benzo[c][1,2,5]thiadiazole-7,4-diyl))bis(methanylylidene))bis(3-ethyl-2-thioxothiazolidin-4-one) (O-IDTBR) is used as acceptor. In kinetics, the entanglements of P3HT-H are relieved due to the higher molecular diffusivity of P3HT-L. In thermodynamics, the miscibility of P3HT-L/O-IDTBR, P3HT-H/O-IDTBR, and P3HT-L/P3HT-H blends increases in turn. Hence, P3HT forms a more ordered structure with longer CLs after adding P3HT-L, which also drives O-IDTBR dispersed in P3HT crystalline regions diffuse to the O-IDTBR crystalline regions to further self-organize. Consequently, the CLs of both P3HT and O-IDTBR are extended, while keeping the intermixed phase amount proper. The optimized microstructure boosts device performance from 7.03% to 7.80%, which is one of the highest values reported for P3HT/O-IDTBR blends. This is a novel way to solve the conflict mentioned above, which may provide guidance to finely regulating the morphology of the active layer.

Perovskite Solar Cells toward Eco-Friendly Printing.

Eco-friendly printing is important for mass manufacturing of thin-film photovoltaic (PV) devices to preserve human safety and the environment and to reduce energy consumption and capital expense. However, it is challenging for perovskite PVs due to the lack of eco-friendly solvents for ambient fast printing. In this study, we demonstrate for the first time an eco-friendly printing concept for high-performance perovskite solar cells. Both the perovskite and charge transport layers were fabricated from eco-friendly solvents via scalable fast blade coating under ambient conditions. The perovskite dynamic crystallization during blade coating investigated using in situ grazing incidence wide-angle X-ray scattering (GIWAXS) reveals a long sol-gel window prior to phase transformation and a strong interaction between the precursors and the eco-friendly solvents. The insights enable the achievement of high quality coatings for both the perovskite and charge transport layers by controlling film formation during scalable coating. The excellent optoelectronic properties of these coatings translate to a power conversion efficiency of 18.26% for eco-friendly printed solar cells, which is on par with the conventional devices fabricated via spin coating from toxic solvents under inert atmosphere. The eco-friendly printing paradigm presented in this work paves the way for future green and high-throughput fabrication on an industrial scale for perovskite PVs.

Efficient and thermally stable organic solar cells based on small molecule donor and polymer acceptor.

Efficient organic solar cells (OSCs) often use combination of polymer donor and small molecule acceptor. Herein we demonstrate efficient and thermally stable OSCs with combination of small molecule donor and polymer acceptor, which is expected to expand the research field of OSCs. Typical small molecule donors show strong intermolecular interactions and high crystallinity, and consequently do not match polymer acceptors because of large-size phase separation. We develop a small molecule donor with suppressed π-π stacking between molecular backbones by introducing large steric hindrance. As the result, the OSC exhibits small-size phase separation in the active layer and shows a power conversion efficiency of 8.0%. Moreover, this OSC exhibits much improved thermal stability, i.e. maintaining 89% of its initial efficiency after thermal annealing the active layer at 180 °C for 7 days. These results indicate a different kind of efficient and stable OSCs.

An organoboron compound with a wide absorption spectrum for solar cell applications.

Organoboron compounds offer new approaches to tune the electronic structures of π-conjugated molecules. In this work, an electron acceptor (M-BNBP4P-1) is developed by endcapping an organoboron core unit with two strong electron-withdrawing groups. M-BNBP4P-1 exhibits a unique wide absorption spectrum with two strong absorption bands in the long wavelength region (λmax = 771 nm) and the short wavelength region (λmax = 502 nm), which indicate superior sunlight harvesting capability. This is due to its special electronic structure, i.e. a delocalized LUMO and a localized HOMO. Prototype solution-processed organic solar cells based on M-BNBP4P-1 show a power conversion efficiency of 7.06% and a wide photoresponse from 350 nm to 880 nm.

Diketopyrrolopyrrole-based Conjugated Polymers Bearing Branched Oligo(Ethylene Glycol) Side Chains for Photovoltaic Devices.

Conjugated polymers are essential for solution-processable organic opto-electronic devices. In contrast to the great efforts on developing new conjugated polymer backbones, research on developing side chains is rare. Herein, we report branched oligo(ethylene glycol) (OEG) as side chains of conjugated polymers. Compared with typical alkyl side chains, branched OEG side chains endowed the resulting conjugated polymers with a smaller π-π stacking distance, higher hole mobility, smaller optical band gap, higher dielectric constant, and larger surface energy. Moreover, the conjugated polymers with branched OEG side chains exhibited outstanding photovoltaic performance in polymer solar cells. A power conversion efficiency of 5.37 % with near-infrared photoresponse was demonstrated and the device performance could be insensitive to the active layer thickness.

Polymer Acceptor Based on Double B←N Bridged Bipyridine (BNBP) Unit for High-Efficiency All-Polymer Solar Cells.

A novel polymer acceptor based on the double B←N bridged bipyridine building block is reported. All-polymer solar cells based on the new polymer acceptor show a power conversion efficiency of as high as 6.26% at a photon energy loss of only 0.51 eV.

An Electron-Deficient Building Block Based on the B←N Unit: An Electron Acceptor for All-Polymer Solar Cells.

A double B←N bridged bipyridyl (BNBP) is a novel electron-deficient building block for polymer electron acceptors in all-polymer solar cells. The B←N bridging units endow BNBP with fixed planar configuration and low-lying LUMO/HOMO energy levels. As a result, the polymer based on BNBP units (P-BNBP-T) exhibits high electron mobility, low-lying LUMO/HOMO energy levels, and strong absorbance in the visible region, which is desirable for polymer electron acceptors. Preliminary all-polymer solar cell (all-PSC) devices with P-BNBP-T as the electron acceptor and PTB7 as the electron donor exhibit a power conversion efficiency (PCE) of 3.38%, which is among the highest values of all-PSCs with PTB7 as the electron donor.

A polymer acceptor with an optimal LUMO energy level for all-polymer solar cells.

A key parameter for polymer electron acceptors is the lowest unoccupied molecular orbital (LUMO) energy level (ELUMO). For state-of-the-art polymer electron acceptors based on the naphthalene diimide (NDI) unit, their ELUMO are low-lying and cannot be tuned, leading to a low open-circuit voltage (Voc) of the resulting all-polymer solar cells (all-PSCs). We report that polymer electron acceptors based on the double B←N bridged bipyridine (BNBP) unit exhibit tunable ELUMO because of their delocalized LUMOs over polymer backbones. The ELUMO of the copolymer of the BNBP unit and selenophene unit (P-BNBP-Se) is lower by 0.16 eV than that of the copolymer of the BNBP unit and thiophene unit (P-BNBP-T). As a result, the energy levels of P-BNBP-Se match well with the widely-used polymer donor, poly[(ethylhexyl-thiophenyl)-benzodithiophene-(ethylhexyl)-thienothiophene] (PTB7-Th). The electron mobility of P-BNBP-Se (µe = 2.07 × 10-4 cm2 V-1 s-1) is also higher than that of P-BNBP-T (µe = 7.16 × 10-5 cm2 V-1 s-1). While the all-PSC device based on the PTB7-Th:P-BNBP-T blend shows a moderate power conversion efficiency (PCE) of 2.27%, the corresponding device with P-BNBP-Se as the acceptor exhibits a PCE as high as 4.26%. Moreover, owing to the suitable ELUMO of P-BNBP-Se, the all-PSC device of P-BNBP-Se shows a Voc up to 1.03 V, which is higher by 0.22 V than that with the conventional NDI-based polymer acceptor. These results indicate that BNBP-based polymers can give all-PSCs with high PCEs, remarkably high Voc values and small photon energy losses.

Developing conjugated polymers with high electron affinity by replacing a C-C unit with a B←N unit.

The key parameters of conjugated polymers are lowest unoccupied molecular orbital (LUMO) and highest occupied molecular orbital (HOMO) energy levels. Few approaches can simultaneously lower LUMO and HOMO energy levels of conjugated polymers to a large extent (>0.5 eV). Disclosed herein is a novel strategy to decrease both LUMO and HOMO energy levels of conjugated polymers by about 0.6 eV through replacement of a C-C unit by a B←N unit. The replacement makes the resulting polymer transform from an electron donor into an electron acceptor, and is proven by fluorescence quenching experiments and the photovoltaic response. This work not only provides an effective approach to tune the LUMO/HOMO energy levels of conjugated polymers, but also uses organic boron chemistry as a new toolbox to develop conjugated polymers with high electron affinity for polymer optoelectronic devices.