Laser cooling ytterbium doped silica by 67 K from ambient temperature.

Laser cooling of a 5 cm long, 1 mm diameter ytterbium doped (6.56×1025 ions/m3) silica rod by 67 K from room temperature was achieved. For the pump source, a 100 W level ytterbium fiber amplifier was constructed along with a 1032 nm fiber Bragg grating seed laser. Experiments were done in vacuum and monitored with the non-contact differential luminescence thermometry method. Direct measurements of the absorption spectrum as a function of temperature were made, to avoid any possible ambiguities from site-selectivity and deviations from McCumber theory at low temperature. This allowed direct computation of the cooling efficiency versus temperature at the pump wavelength, permitting an estimated heat lift of 1.42 W/m as the sample cooled from ambient temperature to an absolute temperature of 229 K.

Impact of site-selective spectroscopy on laser cooling parameter characterization.

From laser design to optical refrigeration, experimentally measured fluorescence spectra are often utilized to obtain input parameters for predictive models. However, in materials that exhibit site-selectivity, the fluorescence spectra depend on the excitation wavelength employed to take the measurement. This work explores different conclusions that predictive models reach after inputting such varied spectra. Here, temperature-dependent site-selective spectroscopy is carried out on an ultra-pure Yb, Al co-doped silica rod fabricated by the modified chemical vapor deposition technique. The results are discussed in the context of characterizing ytterbium doped silica for optical refrigeration. Measurements made between 80 K and 280 K at several different excitation wavelengths yield unique values and temperature dependencies of the mean fluorescence wavelength. For the excitation wavelengths studied here, the variation in emission lineshapes ultimately lead to calculated minimum achievable temperatures (MAT) ranging between 151 K and 169 K, with theoretical optimal pumping wavelengths between 1030 nm and 1037 nm. Direct evaluation of the temperature dependence of the fluorescence spectra band area associated with radiative transitions out of the thermally populated 2F5/2 sublevel may be a better approach to identifying the MAT of a glass where site-selective behavior precludes unique conclusions.

Potential of ytterbium doped silica glass for solid-state optical refrigeration to below 200 K.

We report on the optical refrigeration of ytterbium doped silica glass by >40 K starting at room temperature, which represents more than a two-fold improvement over the previous state-of-the-art. A spectroscopic investigation of the steady-state and time-dependent fluorescence was carried out over the temperature range 80 K to 400 K. The calculated minimum achievable temperature for our Yb3+ doped silica sample is ≈150 K, implying the potential for utilizing ytterbium doped silica for solid-state optical refrigeration below temperatures commonly achieved by standard Peltier devices.

Laser cooling experiments to measure the quantum efficiency of Yb-doped silica fibers.

A detailed investigation into the wavelength-dependent cooling efficiencies of two ultra-pure large core diameter ytterbium-doped silica fibers is carried out by means of the laser-induced thermal modulation spectroscopy (LITMoS) method. From these measurements, an external quantum efficiency of 0.99 is obtained for both fibers. Optimal cooling is seen for pump wavelengths between 1032 and 1035 nm. The crossover wavelength from heating to cooling is identified to be between 1018 and 1021 nm. The fiber with higher Yb3+ ion density exhibits better cooling, seen by the input power normalized temperature differential.

Laser cooling of a Yb doped silica fiber by 18 Kelvin from room temperature.

An ytterbium doped silica optical fiber with a core diameter of 900µm has been cooled by 18.4 K below ambient temperature by pumping with 20 W of 1035 nm light in vacuum. In air, cooling by 3.6 K below ambient was observed with the same 20 W pump. The temperatures were measured with a thermal imaging camera and differential luminescence thermometry. The cooling efficiency is calculated to be 1.2±0.1%. The core of the fiber was codoped with Al3+ for an Al to Yb ratio of 6:1, to allow for a larger Yb concentration and enhanced laser cooling.

Coherent combination of high power fiber amplifiers in a two-dimensional re-imaging waveguide.

Four actively phase-locked beams produced by fiber amplifiers in a master oscillator power amplifier (MOPA) configuration were coherently combined in a glass capillary re-imaging waveguide producing more than 100 W of coherent output with 80% combining efficiency and excellent beam quality. The beam combiner components maintained a temperature below 30 degrees C with no external cooling at >100 W of combined power.

Array waveguide evanescent ribbon coupler for card-to-backplane optical interconnects.

A flexible array waveguide evanescent coupler for card-to-backplane optical interconnects is presented. The proposed technique eliminates traditional 90 degrees out-of-plane turns and local waveguide termination of multidrop bus architectures that hinder conventional card-to-backplane optical interconnections. Evanescent coupling between array waveguide ribbons has been successfully demonstrated. Further experiments have been performed to quantify array waveguide coupling length versus transfer efficiency and waveguide misalignment tolerance. Preliminary optical interconnect testing has demonstrated 2.5GHz operation of the coupler ribbons. The successful high-speed coupling confirms the effectiveness of the proposed method for high-speed computing systems.

Performance evaluation of pilot scale sulfur-oxidizing denitrification for treatment of metal plating wastewater.

A full-scale and two pilot-scale upflow sulfur-oxidizing denitrification (SOD) columns were evaluated using metal plating wastewater as feed. The sludge was autotrophically enriched, and inoculated in the SOD columns attached to the effluent line of three metal plating wastewater treatment facilities. The effects of activated carbon and aeration were also studied, and found effective for the removal of suspended solids and ammonia, respectively. The results showed that the constituents, such as the total nitrogen, nitrates, nitrites, ammonia, chemical oxygen demand (COD), and heavy metals, were effectively removed. The pH was observed to be maintained at 7-8 due to the alkalinity supplied by the sulfur-calcium carbonate (SC) pellet. The denitrification efficiency and start-up period were observed to be affected by the influent quality. Chromium, iron, nickel, copper, and zinc--the major heavy metal components of the influent--were effectively reduced at certain concentrations. Other metal ions were also detected and reduced to undetectable concentrations, but no trends in the comparison with denitrification were observed. From the results it can be concluded that SOD is effective for the removal of nitrogen, particularly nitrates, without a drastic pH change, and can effectively remove minute concentrations of heavy metals and COD in metal plating wastewaters.