The Challenges and Advantages of Distributed Fiber Optic Strain Monitoring in and on the Cementitious Matrix of Concrete Beams.

Distributed fiber optic strain measurement techniques have become increasingly important in recent years, especially in the field of structural health monitoring of reinforced concrete structures. Numerous publications show the various monitoring possibilities from bridges to special heavy structures. The present study is intended to demonstrate the possibilities, but also the challenges, of distributed fiber optic strain measurement in reinforced concrete structures. For this purpose, concrete beams for 3-point bending tests were equipped with optical fibers on the reinforcement and concrete surface as well as in the concrete matrix in order to record the strains in the compression and tension zone. In parallel, an analytical approach based on the maximum strains in the uncracked and cracked states was performed using the Eurocode 2 interpolation coefficient. In principle, the structural design correlates with the measured values, but the strains are underestimated, especially in the cracked zone. During load increase, structural distortions in the compression zone affected the strain signal, making reliable evaluation in this zone difficult. The information content of distributed fiber optic strain measurement in reinforced concrete structures can offer tremendous opportunities. Future research should consider all aspects of the bond, sensor selection and positioning. In addition, there is a lack of information on the long-term stability of the joint and the fiber coating, as well as the effects of dynamic loading.

Advanced Carbon Reinforced Concrete Technologies for Façade Elements of Nearly Zero-Energy Buildings.

The building sector accounts for approx. 40% of total energy consumption and approx. 36% of all greenhouse gas emissions in Europe. As the EU climate targets for 2030 call for a reduction of greenhouse gas emissions by more than half compared to the emissions of 1990 and also aim for climate neutrality by 2050, there is an urgent need to achieve a significant decrease in the energy use in buildings towards Nearly Zero-Energy Buildings (nZEBs). As the energy footprint of buildings includes the energy and greenhouse gas consumption both in the construction phase and during service life, nZEB solutions have to provide energy-efficient and less carbon-intensive building materials, specific thermal insulation solutions, and a corresponding design of the nZEB. Carbon reinforced concrete (CRC) materials have proven to be excellent candidate materials for concrete-based nZEBs since they are characterized by a significantly lower CO2 consumption during component production and much a longer lifecycle. The corresponding CRC technology has been successively implemented in the last two decades and first pure CRC-based buildings are currently being built. This article presents a novel material system that combines CRC technology and suitable multifunctional insulation materials as a sandwich system in order to meet future nZEB requirements. Because of its importance for the life cycle stage of production, cost-efficient carbon fibers (CF) from renewable resources like lignin are used as reinforcing material, and reinforcement systems based on such CF are developed. Cutting edge approaches to produce ultra-thin lightweight CF reinforced concrete panels are discussed with regard to their nZEB relevance. For the life cycle stage of the utilization phase, the thermal insulation properties of core materials are optimized. In this context, novel sandwich composites with thin CRC layers and a cellular lightweight concrete core are proposed as a promising solution for façade elements as the sandwich core can additionally be combined with an aerogel-based insulation. The concepts to realize such sandwich façade elements will be described here along with a fully automated manufacturing process to produce such structures. The findings of this study provide clear evidence on the promising capabilities of the CRC technology for nZEBs on the one hand and on the necessity for further research on optimizing the energy footprint of CRC-based structural elements on the other hand.

Rheology of Alkali-Activated Blended Binder Mixtures.

Alkali-activated cement (AAC) is an alternative cement that has been increasingly studied over the past decades mainly because of its environmental benefits. However, most studies are on heat-cured AACs and are focused on mechanical properties. There is a lack of research on the fresh properties of ambient-cured AAC systems. This study investigates the rheological properties of ambient-temperature-cured alkali-activated blended binder mixtures activated with sodium silicate and sodium hydroxide solutions. The influence of binder amount, alkaline solid to binder ratio (AS/B), sodium silicate to sodium hydroxide solids ratio (SS/SH), and total water content to total solid (from the binding materials) ratio (TW/TS) on the rheological properties are investigated. The effect of borax as an admixture and silica fume as a replacement for fly ash is also investigated. The results showed that both the yield stress and plastic viscosity are mainly affected by the binder content and TW/TS ratio decreasing with the increase of each parameter. The yield stress increased with the increase of the SS/SH ratio. Borax significantly reduced the yield stress, while silica fume's effect was dependent on its dosage.

Setting Time and Strength Monitoring of Alkali-Activated Cement Mixtures by Ultrasonic Testing.

Alkali-activated cement (AAC) is a promising binder that replaces ordinary Portland cement (OPC). In this study, the development of setting time and strength of AAC mixes were studied using ultrasonic testing method. The test results were compared with traditional Vicat setting time and compressive and flexural strengths. The findings showed that setting times and strengths have a strong correlation with ultrasonic velocity curve. The initial setting time corresponds well with the ultrasonic velocity curve's dormant period, and the final setting time with the time it takes to reach the velocity curve's maximum acceleration. Both setting times also showed a correlation with the value of the maximum acceleration. An exponential relation was found between the ultrasonic velocity and the compressive and flexural strengths. The effect of binder content, alkaline solid to binder ratio (AS/B), sodium silicate to sodium hydroxide solids ratio (SS/SH), and total water to total solid binder ratio (TW/TS) on the strength and setting time are also studied using Taguchi method of experimental design. AS/B ratio showed a significant influence on the setting time of AAC while TW/TS ratio showed only a minor effect. The ultrasonic velocities were able to capture the effect of the different parameters similar to the compressive strength. The velocity decreased mainly with the increase of TW/TS ratio and binder content, while AS/B and SS/SH ratios showed a lower influence.

Experimental Study on Concrete under Combined FRP-Steel Confinement.

The confinement of reinforced concrete (RC) compression members by fiber-reinforced polymers (FRPs) is an effective measure for the strengthening and retrofitting of existing structures. Thus far, extensive research on the stress-strain behavior and ultimate limit state design of FRP-confined concrete has been conducted, leading to various design models. However, these models are significantly different when compared to one another. In particular, the use of certain empirical efficiency and reduction factors results in various predictions of load-bearing behavior. Furthermore, most experimental programs solely focus on plain concrete specimens or demonstrate insufficient variation in the material properties. Therefore, this paper presents a comprehensive experimental study on plain and reinforced FRP-confined concrete, limited to circular cross sections. The program included 63 carbon FRP (CFRP)-confined plain and 60 CFRP-confined RC specimens with a variation in the geometries and in the applied materials. The analysis showed a significant influence of the compressive strength of the confined concrete on the confinement efficiency in the design methodology, as well as the importance of the proper determination of individual reduction values for different FRP composites. Finally, applicable experimental test results from the literature were included, enabling the development of a modified stress-strain and ultimate condition design model.

Assessment of Standards and Codes Dedicated to CFRP Confinement of RC Columns.

Reinforced concrete (RC) columns are often placed under confinement to increase their strength and ductility. Carbon fiber reinforced polymer (CFRP) materials have recently been recognized as favorable confinement systems. At present, a number of national standards and codes dedicated to the design of concrete components strengthened with CFRP in general and CFRP confinement in particular are available. These sets of rules provide design equations for confined reinforced concrete columns with circular and rectangular cross sections. Most of the standards and codes exhibit significant differences, including the used predictive models, limitations, observed effects and covered loading conditions. In this paper, five international standards and design guidelines are introduced and discussed. The purpose is to present a constructive and critical assessment of the state-of-the-art design methodologies available for CFRP confined RC columns and to discuss effects not previously considered properly. Therefore, some recent research efforts and findings from the Leipzig University of Applied Sciences are also introduced. The obtained data is used for a comparative study of the guideline predictive equations. Furthermore, it is shown that some new findings concerning the rupture strength and the maximum strength plus accompanying axial strain of a CFRP confined column are suitable to improve the current guidelines.