RESUMEN
All-solid-state lithium-sulfur batteries (ASSLSBs) have attracted intense interest due to their high theoretical energy density and intrinsic safety. However, constructing durable lithium (Li) metal anodes with high cycling efficiency in ASSLSBs remains challenging due to poor interface stability. Here, a compositionally stable, self-lithiated tin (Sn)-carbon (C) composite interlayer (LSCI) between Li anode and solid-state electrolyte (SSE), capable of homogenizing Li-ion transport across the interlayer, mitigating decomposition of SSE, and enhancing electrochemical/structural stability of interface, is developed for ASSLSBs. The LSCI-mediated Li metal anode enables stable Li plating/stripping over 7000 h without Li dendrite penetration. The ASSLSBs equipped with LSCI thus exhibit excellent cycling stability of over 300 cycles (capacity retention of ≈80%) under low applied pressure (<8 MPa) and demonstrate improved rate capability even at 3C. The enhanced electrochemical performance and corresponding insights of the designed LSCI broaden the spectrum of advanced interlayers for interface manipulation, advancing the practical application of ASSLSBs.
RESUMEN
Recently, water resources have become scarce due to the growing global population and human impact on the environment, coupled with the effects of climate change. For solving the problem of global freshwater shortage and increasing the value of discarded polyphenylene sulfide (PPS) filter bags, in this study, balsa wood was used as the base of a photothermal solar evaporator, chitosan solution was used as the binder, and the main photothermal conversion materials used were polyphenylene sulfide (CP) carbide and copper sulfide. In order to create synergistic photothermal conversion materials, freeze-drying and in situ precipitation were used to deposit the photothermal conversion materials on top of the balsa wood. The prepared CP/CuS-wood evaporator has excellent water evaporation performance and light conversion capability, with a water evaporation rate of 2.68 kg m-2 h-1 and a photothermal conversion efficiency of 93.2% under simulated one solar intensity irradiation. In addition, the evaporator can effectively remove organic dyes such as methylene blue and methyl orange. The evaporator's durability and seawater desalination capability have also been confirmed through seawater desalination experiments and outdoor tests. Studies have shown that solar interface photothermal evaporators are a viable solution for desalination and wastewater treatment. This eco-friendly, economically viable and stable photothermal evaporator mentioned in this paper has pioneering features and will be a new paradigm for desalination and wastewater treatment.
RESUMEN
Implantable neural devices that record neurons in various states, including static states, light activities such as walking, and vigorous activities such as running, offer opportunities for understanding brain functions and dysfunctions. However, recording neurons under vigorous activities remains a long-standing challenge because it leads to intense brain deformation. Thus, three key requirements are needed simultaneously for neural devices, that is, low modulus, low specific interfacial impedance, and high electrical conductivity, to realize stable device/brain interfaces and high-quality transmission of neural signals. However, they always contradict each other in current material strategies. Here, a soft fiber neural device capable of stably tracking individual neurons in the deep brain of medium-sized animals under vigorous activity is reported. Inspired by the axon architecture, this fiber neural device is constructed with a conductive gel fiber possessing a network-in-liquid structure using conjugated polymers and liquid matrices and then insulated with soft fluorine rubber. This strategy reconciles the contradictions and simultaneously confers the fiber neural device with low modulus (300 kPa), low specific impedance (579 kΩ µm2), and high electrical conductivity (32 700 S m-1) - ≈1-3 times higher than hydrogels. Stable single-unit spike tracking in running cats, which promises new opportunities for neuroscience is demonstrated.
RESUMEN
Gross anatomy and neuroanatomy are fundamental subjects in medical education. However, learning different anatomical terms and understanding the complexity of the subjects are often challenging for medical students. At National Taiwan University, the 2020-2021 cohort adopted a face-to-face (F2F) learning strategy for gross anatomy and neuroanatomy lecture and laboratory courses until May 17, 2021. After the aforementioned date, the same cohort learned the rest of the gross anatomy and neuroanatomy courses via asynchronous online learning. This study aimed to evaluate the benefits of and students' preferences for F2F and asynchronous online learning strategies in learning gross anatomy and neuroanatomy. A survey with closed-ended and open-ended questions was used to quantitatively and qualitatively explore medical students' learning preferences for two teaching strategies in gross anatomy and neuroanatomy. The results identified different learning preferences among students in learning gross anatomy and neuroanatomy-satisfied with both learning strategies, satisfied with only F2F learning strategy, satisfied with only asynchronous online learning strategy, and satisfied with neither learning strategy. The survey results with closed-ended and open-ended questions showed that medical students preferred F2F learning for anatomical laboratory courses but favored asynchronous online learning for neuroanatomical laboratory courses. In addition, medical students considered peer discussion more critical in learning gross anatomy than neuroanatomy. These findings provide valuable information about medical students' preference for gross anatomy and neuroanatomy courses, which anatomy teachers can consider when planning to enhance their curriculum in the future.
RESUMEN
BACKGROUND: The Oka varicella vaccine strain remains neurovirulent and can establish lifelong latent infection, raising safety concerns about vaccine-related herpes zoster. In this study, we aimed to evaluate the immunogenicity and safety of a skin-attenuated and neuro-attenuated varicella vaccine candidate (v7D vaccine). METHODS: We did this randomised, double-blind, controlled, phase 2a clinical trial in Jiangsu, China. Healthy children aged 3-12 years with no history of varicella infection or vaccination were enrolled and randomly assigned (1:1:1:1) to receive a single subcutaneous injection of the v7D vaccine at 3·3 log10 plaque forming units (PFU; low-dose v7D group), 3·9 log10 PFU (medium-dose v7D group), and 4·2 log10 PFU (high-dose v7D group), or the positive control varicella vaccine (vOka vaccine group). All the participants, laboratory personnel, and investigators other than the vaccine preparation and management staff were masked to the vaccine allocation. The primary outcome was assessment of the geometric mean titres (GMTs) and seroconversion rates of anti-varicella zoster virus immunoglobulin G (IgG) induced by different dose groups of v7D vaccine at 0, 42, 60, and 90 days after vaccination in the per-protocol set for humoral immune response analysis. Safety was a secondary outcome, focusing on adverse events within 42 days post-vaccination, and serious adverse events within 6 months after vaccination. This study was registered on Chinese Clinical Trial Registry, ChiCTR2000034434. FINDINGS: On Aug 18-21, 2020, 842 eligible volunteers were enrolled and randomly assigned treatment. After three participants withdrew, 839 received a low dose (n=211), middle dose (n=210), or high dose (n=210) of v7D vaccine, or the vOka vaccine (n=208). In the per-protocol set for humoral immune response analysis, the anti-varicella zoster virus IgG antibody response was highest at day 90. At day 90, the seroconversion rates of the low-dose, medium-dose, and high-dose groups of v7D vaccine and the positive control vOka vaccine group were 100·0% (95% CI 95·8-100·0; 87 of 87 participants), 98·9% (93·8-100·0; 87 of 88 participants), 97·8% (92·4-99·7; 91 of 93 participants), and 96·4% (89·8-99·2; 80 of 83 participants), respectively; the GMTs corresponded to values of 30·8 (95% CI 26·2-36·0), 31·3 (26·7-36·6), 28·2 (23·9-33·2), and 38·5 (31·7-46·7). The v7D vaccine, at low dose and medium dose, elicited a humoral immune response similar to that of the vOka vaccine. However, the high-dose v7D vaccine induced a marginally lower GMT compared with the vOka vaccine at day 90 (p=0·027). In the per-protocol set, the three dose groups of the v7D vaccine induced a similar humoral immune response at each timepoint, with no statistically significant differences. The incidence of adverse reactions in the low-dose, medium-dose, and high-dose groups of v7D vaccine was significantly lower than that in the vOka vaccine group (17% [35 of 211 participants], 20% [41 of 210 participants], and 13% [27 of 210 participants] vs 24% [50 of 208 participants], respectively; p=0·025), especially local adverse reactions (10% [22 of 211 participants], 14% [30 of 210 participants] and 9% [18 of 210 participants] vs 18% [38 of 208 participants], respectively; p=0·016). None of the serious adverse events were vaccine related. INTERPRETATION: The three dose groups of the candidate v7D vaccine exhibit similar humoral immunogenicity to the vOka vaccine and are well tolerated. These findings encourage further investigations on two-dose vaccination schedules, efficacy, and the potential safety benefit of v7D vaccine in the future. FUNDING: The National Natural Science Foundation of China, CAMS Innovation Fund for Medical Sciences, the Fundamental Research Funds for the Central Universities, and Beijing Wantai. TRANSLATION: For the Chinese translation of the abstract see Supplementary Materials section.
Asunto(s)
Anticuerpos Antivirales , Vacuna contra la Varicela , Varicela , Vacunas Atenuadas , Humanos , Vacuna contra la Varicela/inmunología , Vacuna contra la Varicela/administración & dosificación , Vacuna contra la Varicela/efectos adversos , Método Doble Ciego , Vacunas Atenuadas/inmunología , Vacunas Atenuadas/administración & dosificación , Vacunas Atenuadas/efectos adversos , Masculino , Femenino , Preescolar , Niño , Anticuerpos Antivirales/sangre , Varicela/prevención & control , Varicela/inmunología , China , Herpesvirus Humano 3/inmunología , Inmunogenicidad Vacunal , Vacunación/métodosRESUMEN
Replacement of liquid electrolytes with polymer gel electrolytes is recognized as a general and effective way of solving safety problems and achieving high flexibility in wearable batteries1-6. However, the poor interface between polymer gel electrolyte and electrode, caused by insufficient wetting, produces much poorer electrochemical properties, especially during the deformation of the battery7-9. Here we report a strategy for designing channel structures in electrodes to incorporate polymer gel electrolytes and to form intimate and stable interfaces for high-performance wearable batteries. As a demonstration, multiple electrode fibres were rotated together to form aligned channels, while the surface of each electrode fibre was designed with networked channels. The monomer solution was effectively infiltrated first along the aligned channels and then into the networked channels. The monomers were then polymerized to produce a gel electrolyte and form intimate and stable interfaces with the electrodes. The resulting fibre lithium-ion battery (FLB) showed high electrochemical performances (for example, an energy density of about 128 Wh kg-1). This strategy also enabled the production of FLBs with a high rate of 3,600 m h-1 per winding unit. The continuous FLBs were woven into a 50 cm × 30 cm textile to provide an output capacity of 2,975 mAh. The FLB textiles worked safely under extreme conditions, such as temperatures of -40 °C and 80 °C and a vacuum of -0.08 MPa. The FLBs show promise for applications in firefighting and space exploration.
RESUMEN
It can be difficult for some students to learn three-dimensional anatomical structure concepts. While virtual reality (VR) systems have been reported as helpful for learning, there has been scarce research on either VR teaching strategies or the influence of visually induced motion sickness (VIMS) in the context of large anatomy classes (i.e., over 100 students). The study thus aimed to (1) establish a VR anatomy instruction video for a large class; (2) determine how many students experience VIMS when watching a VR anatomy instruction video; (3) evaluate the influence of VIMS on VR anatomy video-based learning; and (4) examine whether a small screen size alleviates VIMS. Laboratory course students viewing a VR anatomy instruction video about the vascular system were invited to participate in the questionnaire survey. Anatomy faculty and staff participated in an experimental trial to determine whether small screen size could alleviate VIMS. The Likert scale survey revealed that students reported the VR strategy as advantageous and appropriate for large classes, but that it cannot replace practical dissection. Of the total participants, 32% reported experiencing VIMS, and 40% of those experiencing VIMS agreed that this could negatively impact their learning through a VR anatomy instruction video. Adjusting the screen size from large to small significantly delayed the onset of VIMS. In conclusion, the VR anatomy instruction video strategy is feasible and helpful for large classes, but educators should consider VIMS when planning their use of this teaching approach.
Asunto(s)
Anatomía , Educación de Pregrado en Medicina , Estudiantes de Medicina , Realidad Virtual , Humanos , Anatomía/educación , Proyectos Piloto , Estudiantes de Medicina/psicología , Estudiantes de Medicina/estadística & datos numéricos , Femenino , Masculino , Educación de Pregrado en Medicina/métodos , Adulto Joven , Encuestas y Cuestionarios , Adulto , Aprendizaje , Instrucción por Computador/métodos , CurriculumRESUMEN
Introduction: Changes in vision that occur in normal healthy aging can be seen in fundamental measures of monocular vision. However, the nature of the changes in binocular vision with age remain unclear. Methods: A total of 28 older (53-66 years) and 28 younger adults (20-31 years) were enrolled in this study. We performed a battery of tests to assess differences in monocular contrast thresholds and various binocular visual functions including dichoptic masking weight and strength, the binocular balance point for fused stimuli, and stereoacuity in the aging and control groups. Results: Aging significantly increased monocular contrast thresholds (p < 0.001). Although this suggests that aging reduces the effective "input gain" to vision, we also found a significantly elevated contribution of those weaker signals to interocular suppression (p < 0.001). Consequently, there was no significant net difference in the strength of interocular suppression (p = 0.065). We did not find a significant difference of absolute balance point between the two groups (p = 0.090). Lastly, the mean stereoacuity was worse in the older group compared to the younger group (p = 0.002). Discussion: Our findings confirm previous results showing differences in contrast sensitivity and stereoacuity with aging. Furthermore, we find a change in interocular suppression that is a possible consequence of the change in contrast sensitivity. It is suggestive of a cortical system that maintains a homeostatic balance in interocular suppression across the lifespan.
RESUMEN
Transmission and processing of sensory information in the visual system takes time. For motion perception, our brain can overcome this intrinsic neural delay through extrapolation mechanisms and accurately predict the current position of a continuously moving object. But how does the system behave when the motion abruptly changes and the prediction becomes wrong? Here we address this question by studying the perceived position of a moving object with various abrupt motion changes by human observers. We developed a task in which a bar is monotonously moving horizontally, and then motion suddenly stops, reverses, or disappears-then-reverses around two vertical stationary reference lines. Our results showed that participants overestimated the position of the stopping bar but did not perceive an overshoot in the motion reversal condition. When a temporal gap was added at the reverse point, the perceptual overshoot of the end point scaled with the gap durations. Our model suggests that the overestimation of the object position when it disappears is not linear as a function of its speeds but gradually fades out. These results can thus be reconciled in a single process where there is an interplay of the cortical motion prediction mechanisms and the late sensory transient visual inputs.
Asunto(s)
Encéfalo , Percepción de Movimiento , Humanos , Ácido Dioctil Sulfosuccínico , Movimiento (Física) , FenolftaleínaRESUMEN
Calcium-oxygen (Ca-O2) batteries can theoretically afford high capacity by the reduction of O2 to calcium oxide compounds (CaOx) at low cost1-5. Yet, a rechargeable Ca-O2 battery that operates at room temperature has not been achieved because the CaOx/O2 chemistry typically involves inert discharge products and few electrolytes can accommodate both a highly reductive Ca metal anode and O2. Here we report a Ca-O2 battery that is rechargeable for 700 cycles at room temperature. Our battery relies on a highly reversible two-electron redox to form chemically reactive calcium peroxide (CaO2) as the discharge product. Using a durable ionic liquid-based electrolyte, this two-electron reaction is enabled by the facilitated Ca plating-stripping in the Ca metal anode at room temperature and improved CaO2/O2 redox in the air cathode. We show the proposed Ca-O2 battery is stable in air and can be made into flexible fibres that are weaved into textile batteries for next-generation wearable systems.
RESUMEN
Rechargeable calcium (Ca) metal batteries are promising candidates for sustainable energy storage due to the abundance of Ca in Earth's crust and the advantageous theoretical capacity and voltage of these batteries. However, the development of practical Ca metal batteries has been severely hampered by the current cathode chemistries, which limit the available energy and power densities, as well as their insufficient capacity retention and low-temperature capability. Here, we describe the rechargeable Ca/Cl2 battery based on a reversible cathode redox reaction between CaCl2 and Cl2, which is enabled by the use of lithium difluoro(oxalate)borate as a key electrolyte mediator to facilitate the dissociation and distribution of Cl-based species and Ca2+. Our rechargeable Ca/Cl2 battery can deliver discharge voltages of 3 V and exhibits remarkable specific capacity (1000 mAh g-1) and rate capability (500 mA g-1). In addition, the excellent capacity retention (96.5% after 30 days) and low-temperature capability (down to 0 °C) allow us to overcome the long-standing bottleneck of rechargeable Ca metal batteries.
RESUMEN
Rechargeable lithium (Li) metal batteries face challenges in achieving stable cycling due to the instability of the solid electrolyte interphase (SEI). The Li-ion solvation structure and its desolvation process are crucial for the formation of a stable SEI on Li metal anodes and improving Li plating/stripping kinetics. This research introduces an interfacial desolvation coating technique to actively modulate the Li-ion solvation structure at the Li metal interface and regulate the participation of the electrolyte solvent in SEI formation. Through experimental investigations conducted using a carbonate electrolyte with limited compatibility to Li metal, the optimized desolvation coating layer, composed of 12-crown-4 ether-modified silica materials, selectively displaces strongly coordinating solvents while simultaneously enriching weakly coordinating fluorinated solvents at the Li metal/electrolyte interface. This selective desolvation and enrichment effect reduce solvent participation to SEI and thus facilitate the formation of a LiF-dominant SEI with greatly reduced organic species on the Li metal surface, as conclusively verified through various characterization techniques including XPS, quantitative NMR, operando NMR, cryo-TEM, EELS, and EDS. The interfacial desolvation coating technique enables excellent rate cycling stability (i.e., 1C) of the Li metal anode and prolonged cycling life of the Li||LiCoO2 pouch cell in the conventional carbonate electrolyte (E/C 2.6 g/Ah), with 80% capacity retention after 333 cycles.
RESUMEN
Chlorine (Cl)-based batteries such as Li/Cl2 batteries are recognized as promising candidates for energy storage with low cost and high performance. However, the current use of Li metal anodes in Cl-based batteries has raised serious concerns regarding safety, cost, and production complexity. More importantly, the well-documented parasitic reactions between Li metal and Cl-based electrolytes require a large excess of Li metal, which inevitably sacrifices the electrochemical performance of the full cell. Therefore, it is crucial but challenging to establish new anode chemistry, particularly with electrochemical reversibility, for Cl-based batteries. Here we show, for the first time, reversible Si redox in Cl-based batteries through efficient electrolyte dilution and anode/electrolyte interface passivation using 1,2-dichloroethane and cyclized polyacrylonitrile as key mediators. Our Si anode chemistry enables significantly increased cycling stability and shelf lives compared with conventional Li metal anodes. It also avoids the use of a large excess of anode materials, thus enabling the first rechargeable Cl2 full battery with remarkable energy and power densities of 809â Wh kg-1 and 4,277â W kg-1 , respectively. The Si anode chemistry affords fast kinetics with remarkable rate capability and low-temperature electrochemical performance, indicating its great potential in practical applications.
RESUMEN
Rechargeable lithium metal batteries (LMBs) using high-voltage cathodes have been attractive in delivering high-energy density, but it is still challenging to reach excellent cycling performance for practical applications due to the notorious reactivity of metallic lithium as well as the unstable nature of the cathode. Here, we demonstrate a formulated carbonated-based electrolyte with LiPF6 that supports the most commercial aggressive and high-voltage cathode with the combination of cosolvent, diluent, and additives to address the issue in LMBs by providing a stable interface/interphase on both the anode and cathode. The electrolyte's solvation structure is adjusted to reduce free carbonate solvents in the decomposition and contribution to the solid-electrolyte interphase (SEI) formation. The thin LiF-rich SEI and achieved uniform Li deposition afforded a high Coulombic efficiency of 99.5% for Li|Cu half cells and good cycling stability in Li||NMC811 full cells. The Li||NMC811 full cells showed good cycling life with a capacity retention of â¼80% over 280 cycles at an areal capacity of 4.0 mAh cm-2, the lean electrolyte of 5 µL mAh-1, and a thin 50 µm Li metal, demonstrating its advantage toward practical applications.
RESUMEN
Towards the difficulties of traditional processing technology in loading high-concentration functional fillers to realize the target electromagnetic interference shielding (EMI SE) performance, and constructing the arbitrary-designated architectures for serving advanced electronics, this work innovatively formulated a functional multi-walled carbon nanotubes@cellulose nanofibers (MWCNT@OCNF) ink for direct ink writing (DIW) 3D printing, which not only possessed high freedom on the proportion of functional particles, but also imparted to the ideal rheological performance for 3D printing. Based on the pre-programmed printing trajectories, a series of porous scaffolds featuring exceptional functionalities were architected. Particularly for the electromagnetic waves (EMWs) shielding behaviors, the optimized one with "full-mismatched" architecture posed the ultralight structure (0.11 g/cm3) and superior SE performance (43.5 dB) in the X-band frequency region. More encouragingly, the 3D-printed scaffold with hierarchical pores possessed the ideal electromagnetic compatibility on EMWs signal, where the radiation intensity generated by EMWs signal fluctuated in a step pattern in 0 and 1500 µT/cm2 as loading and unloading scaffolds. Overall, this study paved a novel path for the formulation of functional inks to print lightweight, multi-structure, and high-efficiency EMI SE scaffolds for the next-generation shielding elements.
RESUMEN
Anode-free lithium (Li) metal batteries are desirable candidates in pursuit of high-energy-density batteries. However, their poor cycling performances originated from the unsatisfactory reversibility of Li plating/stripping remains a grand challenge. Here we show a facile and scalable approach to produce high-performing anode-free Li metal batteries using a bioinspired and ultrathin (250â nm) interphase layer comprised of triethylamine germanate. The derived tertiary amine and Lix Ge alloy showed enhanced adsorption energy that significantly promoted Li-ion adsorption, nucleation and deposition, contributing to a reversible expansion/shrinkage process upon Li plating/stripping. Impressive Li plating/stripping Coulombic efficiencies (CEs) of ≈99.3 % were achieved for 250â cycles in Li/Cu cells. In addition, the anode-free LiFePO4 full batteries demonstrated maximal energy and power densities of 527â Wh kg-1 and 1554â W kg-1 , respectively, and remarkable cycling stability (over 250â cycles with an average CE of 99.4 %) at a practical areal capacity of ≈3â mAh cm-2 , the highest among state-of-the-art anode-free LiFePO4 batteries. Our ultrathin and respirable interphase layer presents a promising way to fully unlock large-scale production of anode-free batteries.
RESUMEN
Lithium-sulfur all-solid-state batteries using inorganic solid-state electrolytes are considered promising electrochemical energy storage technologies. However, developing positive electrodes with high sulfur content, adequate sulfur utilization, and high mass loading is challenging. Here, to address these concerns, we propose using a liquid-phase-synthesized Li3PS4-2LiBH4 glass-ceramic solid electrolyte with a low density (1.491 g cm-3), small primary particle size (~500 nm) and bulk ionic conductivity of 6.0 mS cm-1 at 25 °C for fabricating lithium-sulfur all-solid-state batteries. When tested in a Swagelok cell configuration with a Li-In negative electrode and a 60 wt% S positive electrode applying an average stack pressure of ~55 MPa, the all-solid-state battery delivered a high discharge capacity of about 1144.6 mAh g-1 at 167.5 mA g-1 and 60 °C. We further demonstrate that the use of the low-density solid electrolyte increases the electrolyte volume ratio in the cathode, reduces inactive bulky sulfur, and improves the content uniformity of the sulfur-based positive electrode, thus providing sufficient ion conduction pathways for battery performance improvement.
RESUMEN
Fiber lithium-ion batteries represent a promising power strategy for the rising wearable electronics. However, most fiber current collectors are solid with vastly increased weights of inactive materials and sluggish charge transport, thus resulting in low energy densities which have hindered the development of fiber lithium-ion batteries in the past decade. Here, a braided fiber current collector with multiple channels was prepared by multi-axial winding method to not only increase the mass fraction of active materials, but also to promote ion transport along fiber electrodes. In comparison to typical solid copper wires, the braided fiber current collector hosted 139 % graphite with only 1/3 mass. The fiber graphite anode with braided current collector delivered high specific capacity of 170â mAh g-1 based on the overall electrode weight, which was 2 times higher than that of its counterpart solid copper wire. The resulting fiber battery showed high energy density of 62â Wh kg-1 .
RESUMEN
PURPOSE: Noninvasive coronary CT angiography (CCTA) was used to retrospectively analyze the characteristics of coronary artery disease (CAD) in patients with thoracic tumors and the impact of the results on clinical surgery decision-making, thus increasing the understanding of perioperative cardiac risk evaluation. METHOD: A total of 779 patients (age 68.6 ± 6.6 years) with thoracic tumor (lung, esophageal, and mediastinal tumor) scheduled for non-cardiac surgery were retrospectively enrolled. Patients were divided into two groups: accepted or canceled surgery. Clinical data and CCTA results were compared between the two groups, and multivariate logistic regression analysis was performed to determine predictors of the events of cancellations of scheduled surgeries. RESULTS: 634 patients (81.4%) had non-significant CAD and 145 patients (18.6%) had significant CAD. Single, 2, and 3 vessel disease was found in 173 (22.2%), 93 (11.9%) and 50 (6.4%) patients, respectively. 500 (64.2%), 96 (12.3%), 96 (12.3%), 56 (7.2%) and 31 (4.0%) patients were rated as CACS 0, 1-99, 100-399, 400-999 and > 1000, respectively. Cancellations of scheduled procedures continue to increase based on the severity of the stenosis and the number of major coronary artery stenosis. The degree of stenosis and the number of vascular stenosis were independent predictors of cancelling scheduled surgery. CONCLUSIONS: For patients with thoracic tumors scheduled for non-cardiac surgery, the results suggested by CCTA significantly influenced surgery planning and facilitated to reduce perioperative cardiovascular events.
Asunto(s)
Enfermedad de la Arteria Coronaria , Estenosis Coronaria , Neoplasias Torácicas , Humanos , Persona de Mediana Edad , Anciano , Angiografía por Tomografía Computarizada , Estudios Retrospectivos , Constricción Patológica , Angiografía Coronaria/métodos , Enfermedad de la Arteria Coronaria/diagnóstico por imagen , Enfermedad de la Arteria Coronaria/cirugía , Valor Predictivo de las Pruebas , Neoplasias Torácicas/diagnóstico por imagen , Neoplasias Torácicas/cirugíaRESUMEN
Correction for 'Virtual microwells for digital microfluidic reagent dispensing and cell culture' by Irwin A. Eydelnant et al., Lab Chip, 2012, 12, 750-757, https://doi.org/10.1039/C2LC21004E.