Psychological well-being in Europe after the outbreak of war in Ukraine.

The Russian invasion of Ukraine on February 24, 2022, has had devastating effects on the Ukrainian population and the global economy, environment, and political order. However, little is known about the psychological states surrounding the outbreak of war, particularly the mental well-being of individuals outside Ukraine. Here, we present a longitudinal experience-sampling study of a convenience sample from 17 European countries (total participants = 1,341, total assessments = 44,894, countries with >100 participants = 5) that allows us to track well-being levels across countries during the weeks surrounding the outbreak of war. Our data show a significant decline in well-being on the day of the Russian invasion. Recovery over the following weeks was associated with an individual's personality but was not statistically significantly associated with their age, gender, subjective social status, and political orientation. In general, well-being was lower on days when the war was more salient on social media. Our results demonstrate the need to consider the psychological implications of the Russo-Ukrainian war next to its humanitarian, economic, and ecological consequences.

Insights on the Synthesis of Al-MCM-41 with Optimized Si/Al Ratio for High-Performance Antibiotic Adsorption.

Studies indicate that approximately two-thirds of the rivers of the world are contaminated by pharmaceutical compounds, especially antibiotics and hormones. Data reported by the World Health Organization (WHO, 2015) revealed an increase of 65% in antibiotic consumption between 2000 and 2015, with a worldwide increase of 200% expected up to 2030. Environmental contamination by antibiotics and their metabolites can cause the alteration of bacterial genes, leading to the generation of superbacteria. In this work, adsorption was explored as a strategy to mitigate antibiotic contamination, proposing the use of the Al-MCM-41 mesoporous material as an efficient and high-capacity adsorbent. Evaluation of the influence of the synthesis parameters enabled understanding of the main variables affecting the adsorption capacity of Al-MCM-41 for the removal of a typical antibiotic, amoxicillin (AMX). It was found that the adsorbent composition and specific surface area were the main factors that should be optimized in order to obtain the highest AMX removal capacity. Using statistical tools, the best Si/Al ratio in Al-MCM-41 was found to be 10.5, providing an excellent AMX uptake of 132.2 mg per gram of adsorbent. The Si/Al ratio was the most significant factor affecting the adsorption. The cation-π interactions increased with an increase of the Al content, while the interactions involving silanols (Yoshida H-bonding and dipole-dipole hydrogen bridges) decreased.

Filament dynamics in vertical confined chemical gardens.

When confined to a Hele-Shaw cell, chemical gardens can grow as filaments, narrow structures with an erratic and tortuous trajectory. In this work, the methodology applied to studies with horizontal Hele-Shaw cells is adapted to a vertical configuration, thus introducing the effect of buoyancy into the system. The motion of a single filament tip is modeled by taking into account its internal pressure and the variation of the concentration of precipitate that constitutes the chemical garden membrane. While the model shows good agreement with the results, it also suggests that the concentration of the host solution of sodium silicate also plays a role in the growth of the structures despite being in stoichiometric excess.

Archimedean Spirals Form at Low Flow Rates in Confined Chemical Gardens.

We describe and study the formation of confined chemical garden patterns. At low flow rates of injection of cobalt chloride solution into a Hele-Shaw cell filled with sodium silicate, the precipitate forms with a thin filament wrapping around an expanding "candy floss" structure. The result is the formation of an Archimedean spiral structure. We model the growth of the structure mathematically. We estimate the effective density of the precipitate and calculate the membrane permeability. We set the results within the context of recent experimental and modeling work on confined chemical garden filaments.

Evaluation of antiplasmodial activity and cytotoxicity assays of amino acids functionalized magnetite nanoparticles: Hyperthermia and flow cytometry applications.

We report the synthesis of magnetite nanoparticles (MNP) and their functionalization with glycine (MNPGly), ß-alanine (MNPAla), L-phenylalanine (MNPPhAla), D-(-)-α-phenylglycine (MNPPhGly) amino acids. The functionalized nanoparticles were characterized by Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron paramagnetic resonance (EPR), vibrating sample magnetometry (VSM), Mössbauer spectroscopy (MS), magnetic hyperthermia (MH), dynamic light scattering and zeta potential. The functionalized nanoparticles had isoelectric points (IEP) at pH ≃ 4.4, 5.8, 5.9 and 6.8 for samples MNPGly, MNPAla, MNPPhGly and MNPPhAla, respectively, while pure magnetite had an IEP at pH 5.6. In the MH experiments, the samples showed specific absorption rate (SAR) of 64, 71, 74, 81 and 66 W/g for MNP, MNPGly, MNPAla, MNPPhGly, and MNPPhAla, respectively. We used a flow cytometric technique to determine the cellular magnetic nanoparticles plus amino acids content. Magnetic fractionation and characterization of Resovist® magnetic nanoparticles were performed for applications in magnetic particle imaging (MPI). We have also studied the antiproliferative and antiparasitic effects of functionalized MNPs. Overall, the data showed that the functionalized nanoparticles have great potential for using as environmental, antitumor, antiparasitic agents and clinical applications.

Filament dynamics in planar chemical gardens.

Filaments in a planar chemical garden grow following tortuous, erratic paths. We show from statistical mechanics that this scaling results from a self-organized dispersion mechanism. Effective diffusivities as high as 10-5 m2 s-1 are measured in 2D laboratory experiments. This efficient transport is four orders of magnitude larger than molecular diffusion in a liquid, and ensures widespread contact and exchange between fluids in the chemical-garden structure and its surrounding environment.

Electrochemical incineration of glyphosate wastewater using three-dimensional electrode.

Anodic oxidation of recalcitrant organic compounds is still challenging concerning to the anode material and mass transport limitations imposed by the low concentration. In this work, we studied the degradation of a real wastewater containing glyphosate using an electrode of PbO2 electrodeposited on a three-dimensional matrix of reticulated vitreous carbon (RVC). The high mass transfer rate provided by the RVC/PbO2 anode is demonstrated. A Box-Behnken factorial design was used for a systematic analysis of the effects of current density, flow rate and temperature on the degradation and mineralisation kinetics, current efficiency and specific energy consumption. The optimised degradation performance was achieved applying 30 mA cm-2, 3000 mL min-1 and 50°C. As the flow rate increases from 150 to 1500 mL min-1, the current efficiency increases from 18% to 65% and the energy consumption dropped from 72 to 33 kWh kg-1 due to the mass transfer enhancement promoted by the porous matrix. The efficacy of the electrochemical process for the treatment of real effluents using the three-dimensional PbO2 has been demonstrated.

A Simple, Long-Lasting Treatment for Concrete by Combining Hydrophobic Performance with a Photoinduced Superhydrophilic Surface for Easy Removal of Oil Pollutants.

Superhydrophobic surfaces present promising applications in the protection of building materials, such as the self-cleaning effect promoted by their high water-repellent properties. However, these surfaces easily lose their properties when exposed to oil contaminants. This is a critical weak point for their application in building facades, which are exposed to environmental pollutants such as hydrocarbons and vandalism (e.g., grafitti). A viable strategy to remove oils is to produce superhydrophilic surfaces, which present underwater superoleophobic behavior. In the case of buildings, the use of this strategy can be considered counterproductive because it promotes their interaction with water, the main vehicle of most decay agents. In this work, we have successfully combined the advantages of a superhydrophilic coating with a hydrophobic impregnation treatment, which prevents water ingress into the porous structure of the substrate. Specifically, a photoinduced superhydrophilic surface was produced on concrete by simple spraying of a starting sol containing TiO2NPs, which create a Cassie-Baxter state, a silica oligomer, producing a compatible matrix promoting good adhesion to the substrate and polydimethylsiloxane as a hydrophobic agent. After being exposed to sunlight, the treated surfaces switched from superhydrophobic (SCA 160°) to superhydrophilic (SCA < 10°). These surfaces presented underwater superoleophobicity (SCA 152° with CHCl3) and oil-contaminated dust was easily cleaned without employing detergents. The photoactivation does not alter the protection against water absorption (>85% reduction). The treatment showed suitable adhesion to the substrate and good resistance to rainfall and outdoor exposure due to the presence of the hydrophobic silica matrix in the concrete pore structure.

Long-Term Effectiveness, under a Mountain Environment, of a Novel Conservation Nanomaterial Applied on Limestone from a Roman Archaeological Site.

A novel alkoxysilane-based product was applied on limestone samples from a Roman archaeological site. The study consisted of an initial phase to evaluate site environmental conditions in order to choose the most suitable product type to be applied. The decay that was produced in the site is mainly caused by natural action, with water being the main vehicle for the decay agents. Thus, the effectiveness of an innovative product with hydrophobic/consolidant properties and two commercial products (consolidant and hydrophobic agent) were evaluated on limestone from Acinipo site, under laboratory conditions. Next, the long-term effectiveness of the three products under study was evaluated by the exposure of limestone samples in the archaeological site for a period of three years. Since the recognized incompatibility between alkoxysilanes and pure carbonate stones, the interaction between the products and the limestones was widely investigated. The results that were obtained allow for it to be concluded that the innovative product presents adequate compatibility and adherence to the limestone under study, producing a long-term effective, homogeneous, and continuous coating with a depth of penetration of up to 10 mm. However, the commercial products produced discontinuous aggregates on the limestone surface, did not penetrate into its porous structure and it did not produce long-lasting effects.

Primary and Secondary Stability of Single Short Implants.

PURPOSE: This prospective cohort study assessed the effect of bone quality on the primary and secondary stability of single short implants placed in the posterior region. MATERIALS AND METHODS: A total of 39 short implants (4.1 × 6-mm long) were placed in the posterior region of the maxilla or mandible in 18 patients. Bone quality was classified into type I, II, III, or IV as assessed intrasurgically. Primary implant stability was measured with insertion torque, damping capacity (PTV values), and resonance frequency analysis (ISQ values). Secondary stability was measured by ISQ and PTV at abutment installation. Data were analyzed by using repeated-measures ANOVA and Tukey's test, Kruskall-Wallis test, and Spearman correlation tests. RESULTS: Implants placed in bone type IV had significant lower insertion torque and ISQ values as well as higher PTV values than in bone types I to II (P < 0.05). The mean ISQ values were higher at abutment installation than at implant placement (P < 0.05), regardless the bone type. The assessment methods of implant stability showed a moderate correlation. CONCLUSIONS: Bone quality influences both the primary and secondary stability of single short implants in the posterior region.

Foil Strain Gauges Using Piezoresistive Carbon Nanotube Yarn: Fabrication and Calibration.

Carbon nanotube yarns are micron-scale fibers comprised by tens of thousands of carbon nanotubes in their cross section and exhibiting piezoresistive characteristics that can be tapped to sense strain. This paper presents the details of novel foil strain gauge sensor configurations comprising carbon nanotube yarn as the piezoresistive sensing element. The foil strain gauge sensors are designed using the results of parametric studies that maximize the sensitivity of the sensors to mechanical loading. The fabrication details of the strain gauge sensors that exhibit the highest sensitivity, based on the modeling results, are described including the materials and procedures used in the first prototypes. Details of the calibration of the foil strain gauge sensors are also provided and discussed in the context of their electromechanical characterization when bonded to metallic specimens. This characterization included studying their response under monotonic and cyclic mechanical loading. It was shown that these foil strain gauge sensors comprising carbon nanotube yarn are sensitive enough to capture strain and can replicate the loading and unloading cycles. It was also observed that the loading rate affects their piezoresistive response and that the gauge factors were all above one order of magnitude higher than those of typical metallic foil strain gauges. Based on these calibration results on the initial sensor configurations, new foil strain gauge configurations will be designed and fabricated, to increase the strain gauge factors even more.

Producing lasting amphiphobic building surfaces with self-cleaning properties.

Nowadays, producing building surfaces that prevent water and oil uptake and which present self-cleaning activity is still a challenge. In this study, amphiphobic (superhydrophobic and oleophobic) building surfaces were successfully produced. A simple and low-cost process was developed, which is applicable to large-scale building surfaces, according the following procedure: (1) by spraying a SiO2 nanocomposite which produces a closely-packed nanoparticle uniform topography; (2) by functionalizing the previous coating with a fluorinated alkoxysilane, producing high hydrophobicity and oleophobicity. The formation of a Cassie-Baxter regime, in which air pockets could be trapped between the aggregates of particles, was confirmed by topographic study. The building surface demonstrated an excellent self-cleaning performance. Finally, the surface presented lasting superhydrophobicity with high stability against successive attachment/detachment force cycles. This high durability can be explained by the effective grafting of the silica nanocomposite coating skeleton with the substrate, and with the additional fluorinated coating produced by condensation reactions.

Modeling quasi-dark states with temporal coupled-mode theory.

Coupled resonators are commonly used to achieve tailored spectral responses and allow novel functionalities in a broad range of applications. The Temporal Coupled-Mode Theory (TCMT) provides a simple and general tool that is widely used to model these devices. Relying on TCMT to model coupled resonators might however be misleading in some circumstances due to the lumped-element nature of the model. In this article, we report an important limitation of TCMT related to the prediction of dark states. Studying a coupled system composed of three microring resonators, we demonstrate that TCMT predicts the existence of a dark state that is in disagreement with experimental observations and with the more general results obtained with the Transfer Matrix Method (TMM) and the Finite-Difference Time-Domain (FDTD) simulations. We identify the limitation in the TCMT model to be related to the mechanism of excitation/decay of the supermodes and we propose a correction that effectively reconciles the model with expected results. Our discussion based on coupled microring resonators can be useful for other electromagnetic resonant systems due to the generality and far-reach of the TCMT formalism.

Evaluation of physical properties of a nanocomposite after aging, bleaching and staining.

PURPOSE: The objective of the in vitro study was to assess the effect accelerated artificial aging, bleaching agents and coffee staining on the color, gloss, roughness and microhardness of a nanocomposite. MATERIALS AND METHODS: 120 (7 × 2 mm) were prepared and randomly divided into 2 groups (n = 60) depending on the aging. Each group was further subdivided into 6 subgroups (n = 10) according to the bleaching and staining as follows: 10% carbamide peroxide (10% CP), 10% CP + staining, 35% hydrogen peroxide (35% HP), 35% HP + staining, without bleaching treatment (WB) and WB + staining. Scanning electron microscopy was performed for qualitative analysis of the resin surface. Data were submitted to 3-way analysis of variance (ANOVA) and Tukey's test for multiple comparisons. As for ∆E, multiple comparisons were performed by using Tukey's and Dunnett's tests (α = 0.05). RESULTS: The bleaching reduced significantly the microhardness of the nanocomposite in without aging groups. All physical properties were found to be negatively changed after the aging process, with bleaching treatment with 10% CP increasing significantly the roughness and loss of gloss compared to the 35% HP. Staining reduced microhardness of both with and without aging nanocomposite as well as the color of the former (E>25), a significantly different result compared to controls. CONCLUSIONS: The bleaching reduced the microhardness of the nanocomposite, whereas the aging process changed all the properties studied. The bleaching favored extrinsic staining of the with aging nanocomposite.

Producing superhydrophobic roof tiles.

Superhydrophobic materials can find promising applications in the field of building. However, their application has been very limited because the synthesis routes involve tedious processes, preventing large-scale application. A second drawback is related to their short-term life under outdoor conditions. A simple and low-cost synthesis route for producing superhydrophobic surfaces on building materials is developed and their effectiveness and their durability on clay roof tiles are evaluated. Specifically, an organic-inorganic hybrid gel containing silica nanoparticles is produced. The nanoparticles create a densely packed coating on the roof tile surface in which air is trapped. This roughness produces a Cassie-Baxter regime, promoting superhydrophobicity. A surfactant, n-octylamine, was also added to the starting sol to catalyze the sol-gel process and to coarsen the pore structure of the gel network, preventing cracking. The application of ultrasound obviates the need to use volatile organic compounds in the synthesis, thereby making a 'green' product. It was also demonstrated that a co-condensation process effective between the organic and inorganic species is crucial to obtain durable and effective coatings. After an aging test, high hydrophobicity was maintained and water absorption was completely prevented for the roof tile samples under study. However, a transition from a Cassie-Baxter to a Wenzel state regime was observed as a consequence of the increase in the distance between the roughness pitches produced by the aging of the coating.

Spectral engineering with coupled microcavities: active control of resonant mode-splitting.

Optical mode-splitting is an efficient tool to shape and fine-tune the spectral response of resonant nanophotonic devices. The active control of mode-splitting, however, is either small or accompanied by undesired resonance-shifts, often much larger than the resonance splitting. We report a control mechanism that enables reconfigurable and widely tunable mode splitting while efficiently mitigating undesired resonance shifts. This is achieved by actively controlling the excitation of counter-traveling modes in coupled resonators. The transition from a large splitting (80 GHz) to a single-notch resonance is demonstrated using low-power microheaters (35 mW). We show that the spurious resonance shift in our device is only limited by thermal crosstalk, and resonance-shift-free splitting control may be achieved.

Efficacy of tooth bleaching with the prior application of a desensitizing agent.

AIM: In the present study, we evaluated the efficacy of bleaching on enamel and opposite dentin surfaces using 35% hydrogen peroxide (HP) with the prior application of a desensitizing agent. METHODS: Thirty bovine dental fragments, with thicknesses of 1 mm enamel and 1.75 mm dentin, were stained in a solution of black tea. The fragments were randomly divided into three groups (n = 10) according to the following protocols: (a) 2% neutral fluoride + bleaching; (b) desensitizing agent + bleaching; and (c) without desensitizer + bleaching. The bleaching efficacy was evaluated four times: after staining with tea (baseline) and after each of the 3 weeks of bleaching, by means of the CIE Lab method using a reflectance spectrophotometer. The data coordinate L* was evaluated by an analysis of repeated measures with PROC MIXED and Tukey-Kramer's test. The ΔE values were subjected to anova and Tukey's test (α = 0.05). RESULTS: The 35% HP treatment showed greater efficacy on deep dentin after removal of the enamel stains, with increasing means during all times in all treatments. CONCLUSION: The use of a desensitizing agent prior to the bleaching session did not affect the mechanism of action of 35% HP with regard to tooth depth.

Embedded coupled microrings with high-finesse and close-spaced resonances for optical signal processing.

Single microring resonators have been used in applications such as wavelength multicasting and microwave photonics, but the dependence of the free spectral range with ring radius imposes a trade-off between the required GHz optical channel spacing, footprint and power consumption. We demonstrate four-channel all-optical wavelength multicasting using only 1 mW of control power, with converted channel spacing of 40-60 GHz. Our device is based on a compact embedded microring design fabricated on a scalable SOI platform. The coexistence of close resonance spacing and high finesse (205) in a compact footprint is possible due to enhanced quality factors (30,000) resulting from the embedded configuration and the coupling-strength dependence of resonance spacing, instead of ring size. In addition, we discuss the possibility of achieving continuously mode splitting from a single-notch resonance up to 40 GHz.

The descending branch of the lateral femoral circumflex artery is a good option in CABG with arterial grafts.

INTRODUCTION: The descending branch of the lateral femoral circumflex artery is an option for coronary artery bypass grafting. OBJECTIVE: To evaluate the early patency and adaptation of lumen diameter using multidetector computed angiotomography. METHODS: Thirty-two patients were selected to undergo coronary artery bypass grafting using the descending branch of the lateral circumflex artery, the internal thoracic artery, and other grafts. Evaluations were carried out through high resolution computed tomography performed on the 7th and 90th postoperative day. Diameters of the descending branch of the lateral circumflex artery and the left internal thoracic artery were measured 3 cm before the distal anastomosis, in the middle portion, and 3 cm after the proximal anastomosis. Diameters were compared using paired t-test (P<0.05). RESULTS: Descending branch of the lateral femoral circumflex artery wDescending branch of the lateral femoral circumflex artery was used in 26 patients, as its use was not viable in six patients (18%). It was used as composite graft in all cases. The anterior descending branch was revascularized by the left internal thoracic artery in all cases. Patency rates of the descending branch of the lateral femoral circumflex artery were 96% and 92%, respectively. No occlusions were observed in the left internal thoracic artery (LITA) and no ischemic events were observed in the descending branch of the lateral circumflex. Descending branch of the lateral femoral circumflex artery increased the lumen diameter in the middle (P=0.001) and distal portions (P=0.006); the left internal thoracic artery (LITA) increased in the middle portion (P=0.001). CONCLUSION: Similar to the left internal thoracic artery, the descending branch of the lateral femoral circumflex artery showed high patency rate and positive luminal adaptation. This early evaluation confirms the descending branch of the lateral femoral circumflex artery as a potential alternative for grafting. Due to anatomical variations, preoperative femoral angiographic evaluation appears to be mandatory.