Chiral perovskite-CdSe/ZnS QDs composites with high circularly polarized luminescence performance achieved through additive-solvent engineering.

Chiral perovskite materials are being extensively studied as one of the most promising candidates for circularly polarized luminescence (CPL)-related applications. Balancing chirality and photoluminescence (PL) properties is of great importance for enhancing the value of the dissymmetry factor (glum), and a higher glum value indicates better CPL. Chiral perovskite/quantum dot (QD) composites emerge as an effective strategy for overcoming the dilemma that achieving strong chirality and PL in chiral perovskite while at the same time achieving high glum in this composite is very crucial. Here, we choose diphenyl sulfoxide (DPSO) as an additive in the precursor solution of chiral perovskite to regulate the lattice distortion. How structural variation affects the chiral optoelectronic properties of the chiral perovskite has been further investigated. We find that chiral perovskite/CdSe-ZnS QD composites with strong CPL have been achieved, and the calculated maximum |glum| of the composites increased over one order of magnitude after solvent-additive modulation (1.55 × 10-3 for R-DMF/QDs, 1.58 × 10-2 for R-NMP-DPSO/QDs, -2.63 × 10-3 for S-DMF/QDs, and -2.65 × 10-2 for S-NMP-DPSO/QDs), even at room temperature. Our findings suggest that solvent-additive modulation can effectively regulate the lattice distortion of chiral perovskite, enhancing the value of glum for chiral perovskite/CdSe-ZnS QD composites.

Donor-Acceptor Copolymer with a Linear Backbone Induced Ordered and Robust Doping Morphology for Efficient and Stable Organic Electrochemical Devices.

Donor (D)-acceptor (A) copolymer-based organic mixed ionic-electronic conductors (OMIECs) exhibit intrinsic environmental stability for they have tailored energy levels. However, their figure-of-merit (µC*) is still falling behind the D-D polymers because of morphology deterioration during the electrochemical doping process. Herein, we developed two D-A copolymers with precisely regulated backbone curvature, namely PTBT-P and PTTBT-P. Compared to the curved PTBT-P and previously reported copolymers, PTTBT-P better keeps its backbone linear, leading to a long-range ordered doping morphology, which is revealed by the in operando X-ray technique. This optimized doping morphology enables a significantly improved operando charge mobility (µ) of 2.44 cm2 V-1 s-1 and a µC* value of 342 F cm-1 V-1 s-1, one of the highest values in D-A copolymer based on OECTs. Besides, we fabricated PTTBT-P-based electrochemical random-access memories and achieved ideal and robust conductance modulation. This study highlights the critical role of backbone curvature control in the optimization of doping morphology for efficient and robust organic electrochemical devices.

Operando Study Insights into Lithiation/Delithiation Processes in a Poly(ethylene oxide) Electrolyte of All-Solid-State Lithium Batteries by Grazing-Incidence X-ray Scattering.

Poly(ethylene oxide) (PEO)-based composite electrolytes (PCEs) are considered as promising candidates for next-generation lithium-metal batteries (LMBs) due to their high safety, easy fabrication, and good electrochemical stability. Here, we utilize operando grazing-incidence small-angle and wide-angle X-ray scattering to probe the correlation of electrochemically induced changes and the buried morphology and crystalline structure of the PCE. Results show that the two irreversible reactions, PEO-Li+ reduction and TFSI- decomposition, cause changes in the crystalline structure, array orientation, and morphology of the PCE. In addition, the reversible Li plating/stripping process alters the inner morphology, especially the PEO-LiTFSI domain radius and distance between PEO-LiTFSI domains, rather than causing crystalline structure and orientation changes. This work provides a new path to monitor a working battery in real time and to a detailed understanding of the Li+ diffusion mechanism, which is essential for developing highly transferable and interface-stable PCE-based LMBs.

The balancing act between high electronic and low ionic transport influenced by perovskite grain boundaries.

A better understanding of the materials' fundamental physical processes is necessary to push hybrid perovskite photovoltaic devices towards their theoretical limits. The role of the perovskite grain boundaries is essential to optimise the system thoroughly. The influence of the perovskite grain size and crystal orientation on physical properties and their resulting photovoltaic performance is examined. We develop a novel, straightforward synthesis approach that yields crystals of a similar size but allows the tuning of their orientation to either the (200) or (002) facet alignment parallel to the substrate by manipulating dimethyl sulfoxide (DMSO) and tetrahydrothiophene-1-oxide (THTO) ratios. This decouples crystal orientation from grain size, allowing the study of charge carrier mobility, found to be improved with larger grain sizes, highlighting the importance of minimising crystal disorder to achieve efficient devices. However, devices incorporating crystals with the (200) facet exhibit an s-shape in the current density-voltage curve when standard scan rates are used, which typically signals an energetic interfacial barrier. Using the drift-diffusion simulations, we attribute this to slower-moving ions (mobility of 0.37 × 10-10 cm2 V-1 s-1) in combination with a lower density of mobile ions. This counterintuitive result highlights that reducing ion migration does not necessarily minimise hysteresis.

Ammonium Sulfate to Modulate Crystallization for High-Performance Rigid and Flexible Perovskite Solar Cells.

Perovskite solar cells (PSCs) are attracting widespread research and attention as highly promising candidates in the field of electronic photovoltaics owing to their exceptional power conversion efficiency (PCE). However, rigid or flexible PSCs still face challenges in preparing full-coverage and low-defect perovskite films, as well as achieving highly reproducible and highly stable devices. Herein, a multifunctional additive 2-aminoethyl hydrogen sulfate (AES) is designed to regulate the film crystallization and thereby form flat and pinhole-free perovskite films. It is found that the introduction of AES can effectively passivate defects, restrain charge carrier recombination, and then achieve a higher fill factor. As seen with grazing incidence wide-angle X-ray scattering (GIWAXS), this approach does not affect the crystal orientation distribution. It is observed that AES addition shows a universality across different perovskite components since the PCE is improved up to 20.7% for FA0.97MA0.03Pb(I0.97Br0.03)3-AES, 22.85% for Cs0.05FA0.95PbI3-AES, 22.23% for FAPbI2.7Br0.3-AES, and 23.32% for FAPI-AES rigid devices. Remarkably, the non-encapsulated flexible Cs0.05 (FA0.85MA0.15)0.95Pb(I0.85Br0.15)3 device with AES additive delivers a PCE of 20.1% and maintains over 97% of its initial efficiency under ambient conditions (25 ± 5% relative humidity) over 2280 h of aging.

Enhanced UV protection in silk fibroin based electrospun fabrics realized via orientation induced high efficiency of azobenzene isomerization.

Due to the poor UV protection capability, natural silk fabrics not only suffer from easy damage by sunshine but also induce possible sunburn in the human body. Efficient azobenzene isomerization and enhanced UV shielding are realized by replacing the natural silk with natural protein silk fibroin (SF) and electrospinning together with light-responsive copolymer P(MEO2-co-OEG300-co-AHMA). Compared to a solution cast film, the absorption peak intensity at 355 nm is 60 % higher in UV-Vis spectra of the electropsun SF/P(MEO2-co-OEG300-co-AHMA) fabrics. This improvement is related to the highly oriented chains, inducing more space and higher efficiency for azobenzene isomerization. Only exposure to visible light for 20 min, the absorption peak corresponding to the trans- state at 355 nm recovers to 92.5 % in the electrospun fabrics, which is at least 100 % faster than that in the solution cast film (50 min). It is related to the zip effect of the isomerization in the oriented chain structure. Thus, not only the absorption of UV radiation, but also the isomerization rate is enhanced. Based on these unique absorption and recovery capabilities, the SF based electrospun fabrics can be used to replace the natural silk fabrics for UV shielding in summer, especially for cyclic use.

Modular slot-die coater for in situ grazing-incidence x-ray scattering experiments on thin films.

Multimodal in situ experiments during slot-die coating of thin films pioneer the way to kinetic studies on thin-film formation. They establish a powerful tool to understand and optimize the formation and properties of thin-film devices, e.g., solar cells, sensors, or LED films. Thin-film research benefits from time-resolved grazing-incidence wide- and small-angle x-ray scattering (GIWAXS/GISAXS) with a sub-second resolution to reveal the evolution of crystal structure, texture, and morphology during the deposition process. Simultaneously investigating optical properties by in situ photoluminescence measurements complements in-depth kinetic studies focusing on a comprehensive understanding of the triangular interdependency of processing, structure, and function for a roll-to-roll compatible, scalable thin-film deposition process. Here, we introduce a modular slot-die coater specially designed for in situ GIWAXS/GISAXS measurements and applicable to various ink systems. With a design for quick assembly, the slot-die coater permits the reproducible and comparable fabrication of thin films in the lab and at the synchrotron using the very same hardware components, as demonstrated in this work by experiments performed at Deutsches Elektronen-Synchrotron (DESY). Simultaneous to GIWAXS/GISAXS, photoluminescence measurements probe optoelectronic properties in situ during thin-film formation. An environmental chamber allows to control the atmosphere inside the coater. Modular construction and lightweight design make the coater mobile, easy to transport, quickly extendable, and adaptable to new beamline environments.

INSIGHT: in situ heuristic tool for the efficient reduction of grazing-incidence X-ray scattering data.

INSIGHT is a Python-based software tool for processing and reducing 2D grazing-incidence wide- and small-angle X-ray scattering (GIWAXS/GISAXS) data. It offers the geometric transformation of the 2D GIWAXS/GISAXS detector image to reciprocal space, including vectorized and parallelized pixel-wise intensity correction calculations. An explicit focus on efficient data management and batch processing enables full control of large time-resolved synchrotron and laboratory data sets for a detailed analysis of kinetic GIWAXS/GISAXS studies of thin films. It processes data acquired with arbitrarily rotated detectors and performs vertical, horizontal, azimuthal and radial cuts in reciprocal space. It further allows crystallographic indexing and GIWAXS pattern simulation, and provides various plotting and export functionalities. Customized scripting offers a one-step solution to reduce, process, analyze and export findings of large in situ and operando data sets.

Multifunctional Umbrella: In Situ Interface Film Forming on the High-Voltage LiCoO2 Cathode by a Tiny Amount of Nanoporous Polymer Additives for High-Energy-Density Li-Ion Batteries.

The LiCoO2 (LCO) cathode is foreseen for extensive commercial applications owing to its high specific capacity and stability. Therefore, there is considerable interest in further enhancing its specific capacity by increasing the charging voltage. However, single-crystal LCO suffers from a significant capacity degradation when charged to 4.5 V due to the irreversible phase transition and unstable structure. Herein, an ultra-small amount (0.5% wt. in the electrode) of multi-functional PIM-1 (a polymer with intrinsic microporosity) additive is utilized to prepare a kind of binder-free electrode. PIM-1 modulates the solvation structure of LiPF6 due to its unique structure, which helps to form a stable, robust, and inorganic-rich cathod-eelectrolyte interphase (CEI) film on the surface of LCO at a high voltage of 4.5 V. This reduces the irreversible phase transition of LCO, thereby enhancing the cyclic stability and improving the rate performance, providing new perspectives for the electrodes fabrication and improving LCO-based high-energy-density cathodes.

Triple-junction solar cells with cyanate in ultrawide-bandgap perovskites.

Perovskite bandgap tuning without quality loss makes perovskites unique among solar absorbers, offering promising avenues for tandem solar cells1,2. However, minimizing the voltage loss when their bandgap is increased to above 1.90 eV for triple-junction tandem use is challenging3-5. Here we present a previously unknown pseudohalide, cyanate (OCN-), with a comparable effective ionic radius (1.97 Å) to bromide (1.95 Å) as a bromide substitute. Electron microscopy and X-ray scattering confirm OCN incorporation into the perovskite lattice. This contributes to notable lattice distortion, ranging from 90.5° to 96.6°, a uniform iodide-bromide distribution and consistent microstrain. Owing to these effects, OCN-based perovskite exhibits enhanced defect formation energy and substantially decreased non-radiative recombination. We achieved an inverted perovskite (1.93 eV) single-junction device with an open-circuit voltage (VOC) of 1.422 V, a VOC × FF (fill factor) product exceeding 80% of the Shockley-Queisser limit and stable performance under maximum power point tracking, culminating in a 27.62% efficiency (27.10% certified efficiency) perovskite-perovskite-silicon triple-junction solar cell with 1 cm2 aperture area.

Microstrain and Crystal Orientation Variation within Naked Triple-Cation Mixed Halide Perovskites under Heat, UV, and Visible Light Exposure.

The instability of perovskite absorbers under various environmental stressors is the most significant obstacle to widespread commercialization of perovskite solar cells. Herein, we study the evolution of crystal structure and microstrain present in naked triple-cation mixed CsMAFA-based perovskite films under heat, UV, and visible light (1 Sun) conditions by grazing-incidence wide-angle X-ray scattering (GIWAXS). We find that the microstrain is gradient distributed along the surface normal of the films, decreasing from the upper surface to regions deeper within the film. Moreover, heat, UV, and visible light treatments do not interfere with the crystalline orientations within annealed polycrystalline films. However, when subjected to heat, the naked perovskite films exhibit a rapid component decomposition, induced by phase separation and ion migration. Conversely, under exposure to UV and 1 Sun light soaking, the naked perovskite films undergo a self-optimization structure evolution during degradation and develop into smoother films with reduced surface potential fluctuations.

Synergistic Effect of Dual Phases to Improve Lithium Storage Properties of Nb2O5.

Niobium pentoxides (Nb2O5) present great potential as next-generation anode candidates due to exceptional lithium-ion intercalation kinetics, considerably high capacity, and reasonable redox potential. Although four phases of Nb2O5 including hexagonal, orthorhombic, tetragonal, and monoclinic polymorphs show diverse characteristics in electrochemical performance, stable lifetime, high specific capacity, and fast intercalation properties cannot be delivered simultaneously with a single phase. Herein, this issue is addressed by generating a homogeneous mixture of orthorhombic and monoclinic crystals at the nanoscale. Reversible lithium-ion intercalation/deintercalation of the monoclinic phase is achieved, and exceptional lithium storage sites are created at the interface of the two phases. As a result, electrochemical features of stable lifetime from the orthorhombic phase and high specific performance from the monoclinic phase are harmoniously combined. This dual-phase Nb2O5/C nanohybrids deliver as high as 380 mA h g-1 (0.01-3.0 V) and 184 mA h g-1 (1.0-3.0 V) after 200 cycles. The essential principle of property enhancement is further confirmed through in situ XRD measurements and DFT calculations. The dual-phase concept can be further applied on electrodes with multiphases to achieve high electrochemical performance.

Dendritic Copper Current Collectors as a Capacity Boosting Material for Polymer-Templated Si/Ge/C Anodes in Li-Ion Batteries.

Dendritic copper offers a highly effective method for synthesizing porous copper anodes due to its intricate branching structure. This morphology results in an elevated surface area-to-volume ratio, facilitating shortened electron pathways during aqueous and electrolyte permeation. Here, we demonstrate a procedure for a time- and cost-efficient synthesis routine of fern-like copper microstructures as a host for polymer-templated Si/Ge/C thin films. Dissolvable Zintl clusters and sol-gel chemistry are used to synthesize nanoporous coating as the anode. Cyclic voltammetry (CV) with KOH as the electrolyte is used to estimate the surface area increase in the dendritic copper current collectors (CCs). Half cells are assembled and tested with battery-related techniques such as CV, galvanostatic cycling, and electrochemical impedance spectroscopy, showing a capacity increase in the dendritic copper cells. Energy-dispersive X-ray spectroscopy is used to estimate the removal of K in the bulk after oxidizing the Zintl phase K12Si8Ge9 in the polymer/precursor blend with SiCl4. Furthermore, scanning electron microscopy images are provided to depict the thin films after synthesis and track the degradation of the half cells after cycling, revealing that the morphological degradation through alloying/dealloying is reduced for the dendritic Cu CC anodes as compared with the bare reference. Finally, we highlight this time- and cost-efficient routine for synthesizing this capacity-boosting material for low-mobility and high-capacity anode coatings.

Boosting the photo-switchability of double-responsive water-soluble polymers by incorporating arylazopyrazole dyes.

Dual thermo- and light-responsive water-soluble copolymers that respond to exclusively non-invasive triggers are obtained by functionalising poly(N,N-dimethylacrylamide) with arylazopyrazole side chains. The light-induced E-Z (trans-Z) photo isomerisation of these dyes provides an exceptionally effective photo-switch, which can reversibly shift the LCST-type phase transition temperatures by almost 25 K.

A Practical Approach Toward Highly Reproducible and High-Quality Perovskite Films Based on an Aging Treatment.

Solution processing of hybrid perovskite semiconductors is a highly promising approach for the fabrication of cost-effective electronic and optoelectronic devices. However, challenges with this approach lie in overcoming the controllability of the perovskite film morphology and the reproducibility of device efficiencies. Here, a facile and practical aging treatment (AT) strategy is reported to modulate the perovskite crystal growth to produce sufficiently high-quality perovskite thin films with improved homogeneity and full-coverage morphology. The resulting AT-films exhibit fewer defects, faster charge carrier transfer/extraction, and suppressed non-radiative recombination compared with reference. The AT-devices achieve a noticeable improvement in the reproducibility, operational stability, and photovoltaic performance of devices, with the average efficiency increased by 16%. It also demonstrates the feasibility and scalability of AT strategy in optimizing the film morphology and device performance for other perovskite components including MAPbI3 , (MAPbBr3 )15 (FAPbI3 )85 , and Cs0.05 (MAPbBr3 )0.17 (FAPbI3 )0.83 . This method opens an effective avenue to improve the quality of perovskite films and photovoltaic devices in a scalable and reproducible manner.

In Situ Surface Reconstruction toward Planar Heterojunction for Efficient and Stable FAPbI3 Quantum Dot Solar Cells.

Pure-phase α-FAPbI3 quantum dots (QDs) are the focus of an increasing interest in photovoltaics due to their superior ambient stability, large absorption coefficient, and long charge-carrier lifetime. However, the trap states induced by the ligand-exchange process limit the photovoltaic performances. Here, a simple post treatment using methylamine thiocyanate is developed to reconstruct the FAPbI3 -QD film surface, in which a MAPbI3 capping layer with a thickness of 6.2 nm is formed on the film top. This planar perovskite heterojunction leads to a reduced density of trap-states, a decreased band gap, and a facilitated charge carrier transport. As a result, a record high power conversion efficiency (PCE) of 16.23% with negligible hysteresis is achieved for the FAPbI3 QD solar cell, and it retains over 90% of the initial PCE after being stored in ambient environment for 1000 h.

Trace Water in Lead Iodide Affecting Perovskite Crystal Nucleation Limits the Performance of Perovskite Solar Cells.

The experimental replicability of highly efficient perovskite solar cells (PSCs) is a persistent challenge faced by laboratories worldwide. Although trace impurities in raw materials can impact the experimental reproducibility of high-performance PSCs, the in situ study of how trace impurities affect perovskite film growth is never investigated. Here, light is shed on the impact of inevitable water contamination in lead iodide (PbI2 ) on the replicability of device performance, mainly depending on the synthesis methods of PbI2 . Through synchrotron-based structure characterization, it is uncovered that even slight additions of water to PbI2 accelerate the crystallization process in the perovskite layer during annealing. However, this accelerated crystallization also results in an imbalance of charge-carrier mobilities, leading to a degradation in device performance and reduced longevity of the solar cells. It is also found that anhydrous PbI2 promotes a homogenous nucleation process and improves perovskite film growth. Finally, the PSCs achieve a remarkable certified power conversion efficiency of 24.3%. This breakthrough demonstrates the significance of understanding and precisely managing the water content in PbI2 to ensure the experimental replicability of high-efficiency PSCs.

Multifunctional Buried Interface Modification Enables Efficient Tin Perovskite Solar Cells.

Tin perovskite solar cells (PSCs) are considered promising candidates to promote lead-free perovskite photovoltaics. However, their power conversion efficiency (PCE) is limited by the easy oxidation of Sn2+ and low quality of tin perovskite film. Herein, an ultra-thin 1-carboxymethyl-3-methylimidazolium chloride (ImAcCl) layer is used to modify the buried interface in tin PSCs, which can induce multifunctional improvements and remarkably enhance the PCE. The carboxylate group (CO) and the hydrogen bond donor (NH) in ImAcCl can interact with tin perovskites, thus significantly suppressing the oxidation of Sn2+ and reducing the trap density in perovskite films. The interfacial roughness is reduced, which contributes to a high-quality tin perovskite film with increased crystallinity and compactness. In addition, the buried interface modification can modulate the crystal dimensionality, favoring the formation of large bulk-like crystals instead of low-dimensional ones in tin perovskite films. Therefore, the charge carrier transport is effectively promoted and the charge carrier recombination is suppressed. Eventually, tin PSCs show a remarkably enhanced PCE from 10.12% to 12.08%. This work highlights the importance of buried interface engineering and provides an effective way to realize efficient tin PSCs.

Precise Methylation Yields Acceptor with Hydrogen-Bonding Network for High-Efficiency and Thermally Stable Polymer Solar Cells.

Utilizing intermolecular hydrogen-bonding interactions stands for an effective approach in advancing the efficiency and stability of small-molecule acceptors (SMAs) for polymer solar cells. Herein, we synthesized three SMAs (Qo1, Qo2, and Qo3) using indeno[1,2-b]quinoxalin-11-one (Qox) as the electron-deficient group, with the incorporation of a methylation strategy. Through crystallographic analysis, it is observed that two Qox-based methylated acceptors (Qo2 and Qo3) exhibit multiple hydrogen bond-assisted 3D network transport structures, in contrast to the 2D transport structure observed in gem-dichlorinated counterpart (Qo4). Notably, Qo2 exhibits multiple and stronger hydrogen-bonding interactions compared with Qo3. Consequently, PM6 : Qo2 device realizes the highest power conversion efficiency (PCE) of 18.4 %, surpassing the efficiencies of devices based on Qo1 (15.8 %), Qo3 (16.7 %), and Qo4 (2.4 %). This remarkable PCE in PM6 : Qo2 device can be primarily ascribed to the enhanced donor-acceptor miscibility, more favorable medium structure, and more efficient charge transfer and collection behavior. Moreover, the PM6 : Qo2 device demonstrates exceptional thermal stability, retaining 82.8 % of its initial PCE after undergoing annealing at 65 °C for 250 hours. Our research showcases that precise methylation, particularly targeting the formation of intermolecular hydrogen-bonding interactions to tune crystal packing patterns, represents a promising strategy in the molecular design of efficient and stable SMAs.