RESUMEN
OBJECTIVE: To report data from the first three years of operation of the RSNA-ACR 3D Printing Registry. METHODS: Data from June 2020 to June 2023 was extracted, including demographics, indications, workflow and user assessments. Clinical indications were stratified by 12 organ systems. Imaging modalities, printing technologies and number of parts per case were assessed. Effort data was analyzed, dividing staff into provider and non-provider categories. The opinions of clinical users were evaluated through a Likert-scale questionnaire, and estimates of procedure time saved were collected. RESULTS: A total of 20 sites and 2,637 cases were included, consisting of 1,863 anatomic models and 774 anatomic guides. Mean patient age for models and guides was 42.4 ± 24.5 years and 56.3 ± 18.5 years respectively. Cardiac models were the most common type of models (27.2%), and neurologic guides were the most common type of guides (42.4%). Material jetting, vat photopolymerization and material extrusion were the most common printing technologies used overall (85.6% of all cases). On average, providers spent 92.4 minutes and non-providers spent 335.0 minutes per case. Providers spent most time on consultation (33.6 minutes), while non-providers focused most on segmentation (148.0 minutes). Confidence in treatment plans increased after using 3D printing (p<.001). Estimated procedure time savings for 155 cases was 40.5 ± 26.1 minutes. CONCLUSION: 3D printing is performed in healthcare facilities for many clinical indications. The registry provides insight into the technologies and workflows used to create anatomic models and guides, and the data shows clinical benefits from 3D printing.
RESUMEN
INTRODUCTION: Mandibular resection and reconstruction are common but complex procedures in head and neck surgery. Resection with adequate margins is critical to the success of the procedure but technical training is restricted to real case experience. Here we describe our experience in the development and evaluation of a mandibular resection and reconstruction simulation module. METHODS: 3D printed (3DP) models of a mandible with a pathologic lesion were developed from imaging data from a patient with an ameloblastoma. During an educational conference, otolaryngology trainees participated in a simulation in which they reviewed a CT scan of the pathologic mandible and then planned their osteotomies before and after handling a 3DP model demonstrating the lesion. The adequacy of the osteotomy margins was assessed and components of the simulation were rated by participants with pre- and post-training surveys. RESULTS: 52 participants met criteria. After reviewing the CT scan, 34 participants (65.3 %) proposed osteotomies clear of the lesion. This proportion improved to 48 (92.3 %, p = 0.001) after handling the 3D model. Among those with initially adequate margins (n = 33), 45.5 % decreased their margins closer to the ideal, 27.2 % made no revision, 21.2 % widened their margins. 92 % of participants found the simulation beneficial for surgical planning and technical training. After the exercise, the majority of participants had increased confidence in conceptualizing the boundaries of the lesion (69.2 %) and their abilities to ablate (76.5 %). CONCLUSIONS: The structured mandibulectomy simulation using 3DP models was useful in the development of trainee experience in segmental mandible resection. LAY SUMMARY: This study presents the first mandibulectomy simulation module for trainees with the use of 3DP models. The use of a 3DP model was also shown to improve the quality of surgical training.
Asunto(s)
Reconstrucción Mandibular , Procedimientos de Cirugía Plástica , Humanos , Osteotomía Mandibular , Mandíbula/diagnóstico por imagen , Mandíbula/cirugía , Osteotomía/métodosRESUMEN
BACKGROUND: Three-dimensional (3D) printing has been increasingly utilized in the healthcare sector for many applications including guiding surgical procedures, creating medical devices, and producing custom prosthetics. As personalized medicine becomes more accessible and desired, 3D printed models emerge as a potential tool in providing patient-specific education. These personalized 3D models are at the intersection of technological innovation and medical education. Our study group utilized a modified Delphi process to create a comprehensive survey tool assessing patient experience with personalized 3D models in preoperative education. METHODS: A rigorous literature review was conducted of prior patient education survey tools in surgical cases across specialties involving personalized 3D printed models. Through categorization and mapping, a core study team reviewed individual questions, removed duplicates, and edited them into generalizable form. A modified Delphi process was then used to solicit feedback on question clarity and relevance from both 3D printing healthcare experts and patients to create a final survey. Results: 173 survey questions from the literature were evaluated by the core study team, yielding 31 unique questions for further review. After multiple rounds of feedback, a final survey containing 18 questions was developed. Conclusion: 3D printed models have the potential to be helpful tools in surgical patient education, and there exists a need to standardize the assessment of patient experience with these models. This survey provides a standardized, generalizable way to investigate the patient experience with personalized 3D-printed models.
RESUMEN
BACKGROUND: Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), the virus that causes coronavirus disease 2019 (COVID-19), can be detected in respiratory samples by real-time reverse transcriptase polymerase chain reaction (RT-PCR) or other molecular methods. Accessibility of diagnostic testing for COVID-19 has been limited by intermittent shortages of supplies required for testing, including flocked nasopharyngeal (FLNP) swabs. METHODS: We developed a 3-dimensional printed nasopharyngeal (3DP) swab as a replacement of the FLNP swab. The performance of 3DP and FLNP swabs were compared in a clinical trial of symptomatic patients at 3 clinical sites (nâ =â 291) using 3 SARS-CoV-2 emergency use authorization tests: a modified version of the Centers for Disease Control and Prevention (CDC) RT-PCR Diagnostic Panel and 2 commercial automated formats, Roche Cobas and NeuMoDx. RESULTS: The cycle threshold-C(t)-values from the gene targets and the RNase P gene control in the CDC assay showed no significant differences between swabs for both gene targets (Pâ =â .152 and Pâ =â .092), with the RNase P target performing significantly better in the 3DP swabs (Pâ <â .001). The C(t) values showed no significant differences between swabs for both viral gene targets in the Roche cobas assay (Pâ =â .05 and Pâ =â .05) as well as the NeuMoDx assay (Pâ =â .401 and Pâ =â .484). The overall clinical correlation of COVID-19 diagnosis between all methods was 95.88% (Kappa 0.901). CONCLUSIONS: The 3DP swabs were equivalent to standard FLNP in 3 testing platforms for SARS-CoV-2. Given the need for widespread testing, 3DP swabs printed onsite are an alternate to FLNP that can rapidly scale in response to acute needs when supply chain disruptions affect availability of collection kits.
Asunto(s)
Prueba de COVID-19 , COVID-19 , Humanos , Nasofaringe , Impresión Tridimensional , SARS-CoV-2 , Manejo de EspecímenesAsunto(s)
Farmacia/métodos , Educación en Farmacia/métodos , Humanos , Farmacéuticos , Estudiantes de FarmaciaRESUMEN
Born from the world of product and service innovation, design thinking is gaining popularity as a method for introducing creative problem solving into the education of health professionals. Mindsets developed through practicing design thinking can help learners and educators address complex healthcare issues in a whole new way. This article aims to introduce the concepts of design thinking to the pharmacy educator, give examples of its use in pharmacy education, and discuss the value of including it in pharmacy education from both an educator and a student's perspective.
RESUMEN
Anterior shoulder dislocations are the most common, large joint dislocations that present to the emergency department (ED). Numerous studies support the use of intraarticular local anesthetic injections for the safe, effective, and time-saving reduction of these dislocations. Simulation training is an alternative and effective method for training compared to bedside learning. There are no commercially available ultrasound-compatible shoulder dislocation models. We utilized a three-dimensional (3D) printer to print a model that allows the visualization of the ultrasound anatomy (sonoanatomy) of an anterior shoulder dislocation. We utilized an open-source file of a shoulder, available from embodi3D® (Bellevue, WA, US). After approximating the relative orientation of the humerus to the glenoid fossa in an anterior dislocation, the humerus and scapula model was printed with an Ultimaker-2 Extended+ 3D® (Ultimaker, Cambridge, MA, US) printer using polylactic acid filaments. A 3D model of the external shoulder anatomy of a live human model was then created using Structure Sensor®(Occipital, San Francisco, CA, US), a 3D scanner. We aligned the printed dislocation model of the humerus and scapula within the resultant external shoulder mold. A pourable ballistics gel solution was used to create the final shoulder phantom. The use of simulation in medicine is widespread and growing, given the restrictions on work hours and a renewed focus on patient safety. The adage of "see one, do one, teach one" is being replaced by deliberate practice. Simulation allows such training to occur in a safe teaching environment. The ballistic gel and polylactic acid structure effectively reproduced the sonoanatomy of an anterior shoulder dislocation. The 3D printed model was effective for practicing an in-plane ultrasound-guided intraarticular joint injection. 3D printing is effective in producing a low-cost, ultrasound-capable model simulating an anterior shoulder dislocation. Future research will determine whether provider confidence and the use of intraarticular anesthesia for the management of shoulder dislocations will improve after utilizing this model.
RESUMEN
PURPOSE: A case of subacute combined degeneration (SCD) of the spinal cord manifesting as severe ataxia and urinary retention in a patient with a history of heavy nitrous oxide abuse and self-supplementation with cyanocobalamin is reported. SUMMARY: A 27-year-old woman was treated in the emergency department for complaints of abdominal pain and inability to urinate for about 12 hours. The patient also complained of worsening lower-extremity weakness for 10 days and a "pins and needles" sensation in the lower extremities for approximately 1 year. She reported nitrous oxide abuse over 3 years (an average of 100-200 "whippit" cartridges daily on 3 or 4 days per week), as well as long-term self-medication with oral and i.m. cyanocobalamin for the purpose of preventing nitrous oxide-induced neurologic symptoms. Results of magnetic resonance imaging (MRI) were highly suggestive of SCD, which is typically seen in primary vitamin B12 deficiency but has been reported in the context of chronic nitrous oxide exposure. Treatment was initiated with cyanocobalamin 1000 µg i.m. daily, to be continued for 5 days and followed by a four-week regimen of 1000 µg i.m. weekly. The patient was discharged after 3 days, despite continued symptoms, with instructions to obtain ongoing care but was lost to follow-up. CONCLUSION: A patient who abused nitrous oxide chronically developed ataxia, paresthesia, and urinary retention while self-medicating with cyanocobalamin. A diagnosis of SCD was supported by MRI findings, symptoms, and the known relationship between nitrous oxide exposure and vitamin B12 deficiency.