Activity and stability of bifunctional perovskite/carbon-based electrodes for the removal of antipyrine by electro-Fenton process.

Bifunctional perovskite/carbon-black(CB)/polytetrafluoroethylene(PTFE) electrodes for electro-generation and catalytic decomposition of hydrogen peroxide to oxidizing hydroxyl radicals have been fabricated. These electrodes were tested for electroFenton (EF) removal of antipyrine (ANT) as a model antipyretic and analgesic drug. The influence of the binder loading (20 and 40 wt % PTFE) and type of solvent (1,3-dipropanediol and water) was studied for the preparation of CB/PTFE electrodes. The electrode prepared with 20 wt % PTFE and water exhibited a low impedance and remarkable H2O2 electro-generation (about 1 g/L after 240 min, a production rate of ca. 6.5 mg/h·cm2). The incorporation of perovskite on CB/PTFE electrodes was also studied following two different methods: i) direct deposition on the CB/PTFE electrode surface and ii) addition in the own CB/PTFE/water paste used for the fabrication. Physicochemical and electrochemical characterization techniques were used for the electrode's characterization. The dispersion of perovskite particles in the own electrode matrix (method ii) exhibited a higher EF performance than the immobilisation onto the electrode surface (method i). EF experiments at 40 mA/cm2 and pH 7 (non-acidified conditions) showed ANT and TOC removals of 30% and 17%, respectively. The increase of current intensity up to 120 mA/cm2 achieved the complete removal of ANT and 92% of TOC mineralisation in 240 min. The bifunctional electrode also proved high stability and durability after 15 h of operation.

Impact of phosphate dosing on the microbial ecology of drinking water distribution systems: Fieldwork studies in chlorinated networks.

Phosphate is routinely dosed to ensure regulatory compliance for lead in drinking water distribution systems. Little is known about the impact of the phosphate dose on the microbial ecology in these systems and in particular the endemic biofilms. Disturbance of the biofilms and embedded material in distribution can cause regulatory failures for turbidity and metals. To investigate the impact of phosphate on developing biofilms, pipe wall material from four independent pipe sections was mobilised and collected using two twin-flushing operations a year apart in a chlorinated UK network pre- and post-phosphate dosing. Intensive monitoring was undertaken, including turbidity and water physico-chemistry, traditional microbial culture-based indicators, and microbial community structure via sequencing the 16S rRNA gene for bacteria and the ITS2 gene for fungi. Whole metagenome sequencing was used to study shifts in functional characteristics following the addition of phosphate. As an operational consequence, turbidity responses from the phosphate-enriched water were increased, particularly from cast iron pipes. Differences in the taxonomic composition of both bacteria and fungi were also observed, emphasising a community shift towards microorganisms able to use or metabolise phosphate. Phosphate increased the relative abundance of bacteria such as Pseudomonas, Paenibacillus, Massilia, Acinetobacter and the fungi Cadophora, Rhizophagus and Eupenicillium. Whole metagenome sequencing showed with phosphate a favouring of sequences related to Gram-negative bacterium type cell wall function, virions and thylakoids, but a reduction in the number of sequences associated to vitamin binding, methanogenesis and toxin biosynthesis. With current faecal indicator tests only providing risk detection in bulk water samples, this work improves understanding of how network changes effect microbial ecology and highlights the potential for new approaches to inform future monitoring or control strategies to protect drinking water quality.

Niveles de anticuerpos anti nucleares por Fana y Ana-Lia en pacientes con enfermedades reumáticas sistémicas / Levels of anti-nuclear antibodies by Fana and Ana-Lia in systemic rheumatic diseases patients

Objetivo: Correlacionar los niveles de anticuerpos antinucleares obtenidos por las técnicas de inmunofluorescencia indirecta (FANA) e inmunoensayo lineal (ANA-LIA) en pacientes diagnosticados o con sospecha clínica de enfermedad autoinmune. Métodos: Se incluyeron 100 pacientes que dieron su consentimiento informado para participar en el estudio. Los ensayos e interpretación de los resultados de las pruebas de FANA y ANA-LIA se realizaron siguiendo las recomendaciones del fabricante. Resultados: el 97,4% de los pacientes estudiados eran de sexo femenino con edad promedio de 42 años, siendo la Artritis reumatoide, Poliartritis y Lupus Eritematoso Sistémico las enfermedades que con mayor frecuencia acompañaron la solicitud médica. Se observó que ambos métodos fueron positivos en el 21% de los casos y que el indice de correlaciòn de Kappa entre las pruebas fue moderado (k= 0,51; p< 0,05), la sensibilidad y especificidad de los métodos fue del 71,4% y 84,8% respectivamente, se observó también que para un determinado patrón fluorescente puede haber positividad de más de un antígeno de la prueba de ANA-LIA y viceversa. Conclusiones: FANA es el método de tamizaje aceptado en la práctica clínica para orientar hacia un diagnóstico clínico de enfermedad autoinmune más probable, debido a la subjetividad en la interpretación de sus resultados y necesidad de entrenamiento en la identificación de los patrones fluorescentes, se requiere del apoyo de otros métodos de laboratorio que permitan identificar con mayor precisión los antígenos reconocidos por los autoanticuerpos, ANA-LIA es una herramienta de laboratorio costo-efectiva de elevada sensibilidad y especificidad que se ajusta a este requerimiento.

Objective: To correlate levels of antinuclear antibodies obtained by indirect immunofluorescence techniques (FANA) and linear immunoassay (ANA-LIA) in patients diagnosed or with clinical suspicion of autoimmune disease. Methods: 100 patients who gave their informed consent to participate in the study were included. Assays and interpretation of results of FANA and ANA-LIA test were performed following the manufacturer's recommendations. Results: 97,4% of the patients studied were female with an average age of 42 years, being rheumatoid arthritis, polyarthritis and systemic lupus erythematosus the diseases that most frequently accompanied the medical request. It was observed that both methods were positive in 21% of the cases and that the Kappa correlation index was moderate between the tests (k = 0,51; p <0,05), the sensitivity and specificity of the methods was 71,4% and 84,8% respectively. It was also observed that for a given fluorescent pattern there may be positivity of more than one antigen of the ANA-LIA test and vice versa. Conclusions: FANA is the screening method accepted in the clinical practice to guide towards a more probable clinical diagnosis of autoimmune disease. Due to the subjectivity in the interpretation of its results and the need for training in the identification of fluorescent patterns, the support of other laboratory methods that allow the identification of antigens recognized by autoantibodies with greater precision is necessary, ANA-LIA is a cost-effective laboratory tool of high sensitivity and specificity that meets this requirement.

Insights into the role of phytohormones regulating pAtNIP5;1 activity and boron transport in Arabidopsis thaliana.

Aiming to counteract B deficiency impacts, plants have developed different strategies in order to reach an optimal growth in soils with limited B availability. These include B transport mechanisms that involves a facilitated transport, via channel proteins, and a high-affinity active transport driven by borate transporters. The AtNIP5;1 channel protein is a member of Major Intrinsic Protein family which facilitates B influx into the roots under low B supply. In order to explore the phytohormone-dependent regulation of AtNIP5;1, the effects of abscisic acid (ABA), ethylene, auxins and cytokinins on the activity of AtNIP5;1 promoter were evaluated using the reporter line pNIP5;1-GUS. The results show that ABA treatment increased pAtNIP5;1 activity. Besides, a larger B uptake was found following ABA treatment under B deficiency suggesting a role of ABA inducing B uptake. The ethylene precursor 1-aminocyclopropane-1-carboxylic acid (ACC) caused an induction of AtNIP5;1 expression although did not correlate with higher B concentrations nor with an improvement in root growth. On the contrary, auxins and cytokinins caused slight changes in pAtNIP5;1 induction. Altogether, these results show a regulatory role of phytohormones in AtNIP5;1 promoter what may affect B transport. The herein provided information may contribute to better understand the regulation of B transport in plants towards minimizing B deficiency impacts on agriculture.

Heterogeneous electro-Fenton as plausible technology for the degradation of imidazolinium-based ionic liquids.

Conventional water treatments are generally inadequate for degradation of emerging pollutants such as ionic liquids (ILs). The use of heterogeneous electro-Fenton (HEF) has attracted great interest, due to its ability to efficiently oxidize a wide range of organic pollutants operating in cycles or in continuous mode. In this study, the removal of a complex IL from the imidazolinium family (1,3-Bis(2,4,6-trimethylphenyl)imidazolinium chloride), by means of HEF using iron alginate spheres as catalyst has been investigated, resulting in significant TOC decay after 6 h. The optimization of the key process parameters (current, IL concentration and catalyst dosage) has been performed using a Box-Behnken experimental design and achieving 76.98% of TOC abatement in 2 h of treatment. Current proved to be a crucial parameter and high catalyst dosage is required to achieve the maximum removal. In addition, an insight about the availability of iron into the reactor and the evolution of several intermediates has been carried out by employing differential pulse voltammetry on screen-printed carbon electrodes. The evolution of the different voltammetric peaks confirmed the influence of iron release, and the generation of several iron complexes has permitted the comprehension of the degradation pathway, which has been validated by chromatographic techniques.

Effects of 25-hydroxycholecalciferol with two D3 vitamin levels on production and immunity parameters in broiler chickens.

This study was performed in Ross 308 chickens aged 1-21 days and aimed to evaluate whether the addition of 25-hydroxycholecalciferol (25(OH)D3 ) to broiler chicken diets affects their growth performance and immunity. A completely random 2 × 2 factorial arrangement was used with two levels of vitamin D3 and the absence or presence of 25(OH)D3 , corresponding to four treatments based on sorghum + soya bean diets: (i) 200 IU of vitamin D3 /kg of feed (Diet 1) (NRC, ), (ii) Diet 1 + 69 µg of 25(OH)D3 /kg of feed (Diet 2), (iii) 5,000 IU of vitamin D3 /kg of feed (Diet 3) and (iv) Diet 3 + 69 µg of 25(OH)D3 /kg of feed (Diet 4). Each treatment was conducted with six replicates of 10 chickens each. Water and feed was supplied ad libitum. The results showed significantly increased growth and tibia ash (p < .05) in the birds fed 5,000, IU of vitamin D3 /kg + 25(OH)D3 . Additionally, the cellular immune response increased significantly (p < .05) in both treatments with added 25(OH)D3. Based on the results obtained under the current test conditions, the addition of 25(OH)D3 at a rate of 69 µg/kg to diets containing vitamin D3 improved the cellular immune response and mineral deposition in the bones of broilers aged 1-21 days. Because these parameters are very important in modern poultry farming, these results indicate that supplementation with 25(OH)D3 should improve broiler production.

p-Nitrophenol degradation by electro-Fenton process: Pathway, kinetic model and optimization using central composite design.

The chemical process scale-up, from lab studies to industrial production, is challenging and requires deep knowledge of the kinetic model and the reactions that take place in the system. This knowledge is also useful in order to be employed for the reactor design and the determination of the optimal operational conditions. In this study, a model substituted phenol such as p-nitrophenol was degraded by electro-Fenton process and the reaction products yielded along the treatment were recorded. The kinetic model was developed using Matlab software and was based on main reactions that occurred until total mineralization which allowed predicting the degradation pathway under this advanced oxidation process. The predicted concentration profiles of p-nitrophenol, their intermediates and by-products in electro-Fenton process were validated with experimental assays and the results were consistent. Finally, based on the developed kinetic model the degradation process was optimized using central composite design taking as key parameters the ferrous ion concentration and current density.

Tamizaje de infecciones por virus Epstein Barr en muestras de sangre mediante el uso de una PCR en tiempo real previo a la cuantificación de la carga viral / Screening for Epstein Barr virus infections in blood samples using real-time PCR previous to viral load quantification

El desorden linfoproliferativo postrasplante es una de las complicaciones más importantes producidas por el virus Epstein Barr (EBV) en pacientes trasplantados de órganos sólidos y de médula ósea ya que afecta la sobrevida del paciente y del injerto. En estos pacientes se han reportado altos niveles de carga viral en sangre periférica que preceden al desarrollo del desorden linfoproliferativo postrasplante. Por esto el monitoreo de la carga viral (CV) permite detectar pacientes en riesgo a desarrollar esta patología para iniciar una terapia preventiva. El objetivo de este trabajo fue desarrollar una técnica de PCR en tiempo real cualitativa (RT PCR) que permitiera ser utilizada como prueba de tamizaje previo a la determinación de CV EBV. De esta manera se podrían minimizar el costo que implicaría la utilización de un método cuantitativo comercial para todas las muestras que ingresaran al monitoreo viral. Teniendo en cuenta el desempeño de la RT PCR desarrollada, se estableció Ct ≤ 37 como valor límite para evitar amplificación inespecífica y seleccionar las muestras candidatas a la determinación de CV EBV. Dicho punto de corte presentó una sensibilidad diagnóstica relativa de 80%, una especificidad diagnóstica relativa de 85%, un valor predictivo positivo (VPP) de 53% y un valor predictivo negativo (VPN) de 95%. Para ello se consideró que valores de CV EBV< 4000 copias/ml sangre eran bajas o no presentaban riesgo de desarrollar complicaciones. El límite de detección LoD 95% fue de 280 copias de EBV/ml sangre (66 ­ 1184, IC 95%). Esta técnica demostró tener una buena performance analítica, ser de fácil implementación y el punto de corte seleccionado nos permitió realizar un buen tamizaje de muestras de pacientes trasplantados que resultaban ser candidatas a la determinación de CV, con la consiguiente disminución de costos (AU)

Post-transplant lymphoproliferative disorder is one of the main complications caused by the Epstein Barr virus (EBV) in solidorgan and bone-marrow transplantation patients affecting survival of both the patient and the graft. High levels of viral load (VL) in peripheral blood preceding the development of posttransplant lymphoproliferative disorder have been reported in these patients. Therefore, VL monitoring allows detection of patients who are at risk of developing this disease to start preventive treatment. The aim of this study was to develop a qualitative real-time PCR technique to use as an early screening test to determine EBV VL. This test may minimize costs related to the use of a commercial quantitative method for all the samples that enter for viral screening. Considering the performance of the RT PCR method developed, a Ct ≤ 37 was established as the cut-off limit to avoid unspecific amplification and select the samples that are candidates for EBV VL determination. This cut-off point had a relative diagnostic sensitivity of 80%, a relative diagnostic specificity of 85%, a positive predictive value (PPV) of 53% and a negative predictive value (NPV) of 95%. Thus, an EBV VL< 4000 copies/ml blood was considered to be low and not to be a risk for developing complications. The 95% limit of detection was 280 copies of EBV/ml blood (66­1184, 95%CI). The technique showed to be of good analytical performance and easy implementation. The cut-off point allowed a good screening of the samples of transplanted patients to detect those who are candidates for VL determination at a lower cost (AU)

A method for thermal diffusivity measurement in fluids.

A technique is proposed for thermal diffusivity measurement in fluids. It is based on the Angstrom method, but with excitation of thermal waves by electromagnetic energy absorption and pyroelectric detection. The good agreement between measured thermal diffusivity of air and some test liquids with literature values shows the validity of the method. It is free of some limitations of conventional photopyroelectric technique with length scanning because it is free of moving parts inside the sample and because it avoids problems associated with the non-parallelism between thermal wave generator surface and sensor. It does not require any data normalization procedure or special sample preparation.

Optimisation of decolourisation and degradation of Reactive Black 5 dye under electro-Fenton process using Fe alginate gel beads.

The aim of this work was to improve the ability of the electro-Fenton process using Fe alginate gel beads for the remediation of wastewater contaminated with synthetic dyes and using a model diazo dye such as Reactive Black 5 (RB5). Batch experiments were conducted to study the effects of main parameters, such as voltage, pH and iron concentration. Dye decolourisation, reduction of chemical oxygen demand (COD) and energy consumption were studied. Central composite face-centred experimental design matrix and response surface methodology were applied to design the experiments and to evaluate the interactive effects of the three studied parameters. A total of 20 experimental runs were set, and the kinetic data were analysed using first-order and second-order models. In all cases, the experimental data were fitted to the empirical second-order model with a suitable degree for the maximum decolourisation of RB5, COD reduction and energy consumption by electro-Fenton-Fe alginate gel beads treatment. Working with the obtained empirical model, the optimisation of the process was carried out. The second-order polynomial regression model suggests that the optimum conditions for attaining maximum decolourisation, COD reduction and energy consumption are voltage, 5.69 V; pH 2.24 and iron concentration, 2.68 mM. Moreover, the fixation of iron on alginate beads suggests that the degradation process can be developed under this electro-Fenton process in repeated batches and in a continuous mode.

Electro-Fenton decolourisation of dyes in an airlift continuous reactor using iron alginate beads.

In this study, electro-Fenton dye degradation was performed in an airlift continuous reactor configuration by harnessing the catalytic activity of Fe alginate gel beads. Electro-Fenton experiments were carried out in an airlift reactor with a working volume of 1.5 L, air flow of 1.5 L/min and 115 g of Fe alginate gel beads. An electric field was applied by two graphite bars connected to a direct current power supply with a constant potential drop. In this study, Lissamine Green B and Reactive Black 5 were selected as model dyes. Fe alginate gel beads can be used as an effective heterogeneous catalyst for the degradation of organic dyes in the electro-Fenton process, as they are more efficient than the conventional electrochemical techniques. At optimal working conditions (3 V and pH 2), the continuous process was performed. For both dyes, the degree of decolourisation increases when the residence time augments. Taking into account hydrodynamic and kinetic behaviour, a model to describe the reactor profile was obtained, and the standard deviation between experimental and theoretical data was lower than 6%. The results indicate the suitability of the electro-Fenton technique to oxidise polluted effluents in the presence of Fe alginate gel beads. Moreover, the operation is possible in a continuous airlift reactor, due to the entrapment of iron in the alginate matrix.

Decolourisation of dyes under electro-Fenton process using Fe alginate gel beads.

This study focuses on the application of electro-Fenton technique by use of catalytic activity of Fe alginate gel beads for the remediation of wastewater contaminated with synthetic dyes. The Fe alginate gel beads were evaluated for decolourisation of two typical dyes, Lissamine Green B and Azure B under electro-Fenton process. After characterization of Fe alginate gel beads, the pH effect on the process with Fe alginate beads and a comparative study of the electro-Fenton process with free Fe and Fe alginate bead was done. The results showed that the use of Fe alginate beads increases the efficiency of the process; moreover the developed particles show a physical integrity in a wide range of pH (2-8). Around 98-100% of dye decolourisation was obtained for both dyes by electro-Fenton process in successive batches. Therefore, the process was performed with Fe alginate beads in a bubble continuous reactor. High color removal (87-98%) was attained for both dyes operating at a residence time of 30 min, without operational problems and maintaining particle shapes throughout the oxidation process. Consequently, the stable performance of Fe alginate beads opens promising perspectives for fast and economical treatment of wastewater polluted by dyes or similar organic contaminants.

Isolation of novel benzo[a]anthracene-degrading microorganisms and continuous bioremediation in an expanded-bed bioreactor.

In the present work, several samples from lab waste containers polluted with polycyclic aromatic hydrocarbons (PAHs) and heavy metals were investigated as potential sources of PAH-degrading microorganisms. After isolating, two fungal strains were selected as the best degrading microorganisms. Genetic identification by sequencing was carried out and they were identified as Trichoderma longibrachiatum and Byssochlamys spectabilis. Their degradation ability was determined in liquid cultures with 100 µM of benzo[a]anthracene. T. longibrachiatum cultures showed highest degradation values (around 97%) after 9 days, furthermore in a second batch the time was reduced to 6 days. To analyse the viability of industrial application, a continuous treatment in an expanded-bed bioreactor was developed operating at different residence times with T. longibrachiatum immobilised on cubes of nylon sponge. It is noticeable that the bioreactor working in continuous mode was able to operate without operational problems and attaining high degradation levels depending on the residence time.

Application of central composite face-centered design and response surface methodology for the optimization of electro-Fenton decolorization of Azure B dye.

PURPOSE: The aim of this work was to improve the ability of electro-Fenton technique for the remediation of wastewater contaminated with synthetic dyes using a model azo dye such as Azure B. METHODS: Batch experiments were conducted to study the effects of main parameters, such as dye concentration, electrode surface area, treatment time, and voltage. In this study, central composite face-centered experimental design matrix and response surface methodology were applied to design the experiments and evaluate the interactive effects of the four studied parameters. A total of 30 experimental runs were set, and the kinetic data were analyzed using first- and second-order models. RESULTS: The experimental data fitted to the empirical second-order model of a suitable degree for the maximum decolorization of Azure B by electro-Fenton treatment. ANOVA analysis showed high coefficient of determination value (R(2) = 0.9835) and reasonable second-order regression prediction. Pareto analysis suggests that the variables, time, and voltage produce the largest effect on the decolorization rate. CONCLUSION: Optimum conditions suggested by the second-order polynomial regression model for attaining maximum decolorization were dye concentration 4.83 mg/L, electrode surface area 15 cm(2), voltage 14.19 V, and treatment time of 34.58 min.

Decontamination of soils containing PAHs by electroremediation: a review.

During the last years, the anthropogenic sources have contributed to organic compound penetration into the environment. One large group of persistent and toxic contaminants is the hydrophobic organic contaminants. Among them, polycyclic aromatic hydrocarbons (PAHs) have been recognized as a representative group of these pollutants with low solubility. In this paper, it is showed the electroremediation of soil contaminated with PAHs as an alternative, to organic compound removal. This technique, mainly used for heavy metal extraction, applies the electric current to promote the movement of contaminants. Nowadays the application of this technique alone or combined with other techniques as for example Fenton or bioremediation is taking fine results to PAHs removal. Although the PAHs soil decontamination by means of the electric field is in an initial stage, many researchers have demonstrated the treatment effectiveness. This paper describes the foremost principles to carry out the electroremediation of soils contaminated with PAHs, just like the different alternatives to improve the electroremediation of PAHs and also the new methodologies of PAHs removal by using hybrid technologies.

Influence of operational parameters on electro-Fenton degradation of organic pollutants from soil.

The combination of the Fenton's reagent with electrochemistry (the electro-Fenton process) represents an efficient method for wastewater treatment. This study describes the use of this process to clean soil or clay contaminated by organic compounds. Model soil of kaolinite clay polluted with the dye Lissamine Green B (LGB) was used to evaluate the capability of the electro-Fenton process. The effects of operating parameters such as electrode material and dye concentration were investigated. Operating in an electrochemical cell under optimized conditions while using electrodes of graphite, a constant potential difference of 5 V, pH 3, 0.2 mM FeSO(4). 7H(2)O, and electrolyte 0.1 M Na(2)SO(4), around 80% of the LGB dye on kaolinite clay was decolorized after 3 hours with an electric power consumption around 0.15 W h g(-1). Furthermore, the efficiency of this process for the remediation of a real soil polluted with phenanthrene, a typical polycyclic aromatic hydrocarbon, has been demonstrated.

Evolution in the resistance of Mycobacterium tuberculosis to anti-tuberculosis drugs in Nicaragua.

SETTING: Nicaragua, a country where the DOTS strategy has been successfully implemented since 1984. OBJECTIVE: To estimate the prevalence and trends of Mycobacterium tuberculosis resistance to first-line anti-tuberculosis drugs. DESIGN: A prospective national survey carried out in 2004 according to the standardised model developed by the World Health Organisation and the International Union Against Tuberculosis and Lung Disease. RESULTS: A total of 423 M. tuberculosis strains were studied. Among the 320 strains evaluated for initial resistance, 13.1% displayed resistance to any drug, lower than the 1998 figure of 15.6%. Overall initial resistance to isoniazid (INH), rifampicin (RMP) and multidrug resistance (MDR) was respectively 6.6%, 0.9% and 0.6%. Initial resistance was higher in older age groups. Overall acquired resistance was 35.9% (n = 103); resistance to INH was 29.3% and to RMP 8.9%, while MDR was 7.9%. The acquired MDR rate was clearly higher in Category I failures (44.4%) than in relapses (3.8%) and retrieved defaulters (2.7%). All resistance rates found in this study were lower than those detected in 1998. CONCLUSION: This study shows low rates of resistance and MDR and a downward trend in all rates, undoubtedly related to the proper implementation of the National Tuberculosis Programme.

Nitric oxide, polyamines and Cd-induced phytotoxicity in wheat roots.

To further explore the biochemical basis of Cd toxicity in developing wheat seedlings, we studied the possible role of nitric oxide (NO) and polyamines as signaling molecules involved in metal-induced root growth inhibition. When used at 0.1 mM, sodium nitroprusside, a NO-releasing compound, inhibited root growth to a similar extent as Cd and enhanced the polyamine contents as Cd also did. Putrescine and spermidine treatments caused significant decreases in root growth with spermine giving the greatest level of inhibition (77% reduction). The simultaneous addition of Cd and inhibitors of putrescine biosynthesis (DFMA and DFMO) prevented increases in putrescine levels but did not restore normal root growth. NO content, as evidenced by the fluorescent probe DAF-FM diacetate, was found to be significantly increased in the roots of both Cd and polyamine treated plants, especially in those exposed to spermine. The effect was specific for NO since the NO scavenger cPTIO almost suppressed the fluorescent signal. Concerning the oxidative status of the root system, only Cd and spermine enhanced lipid peroxidation in roots. At the same time, all treatments led to a significant increase in levels of the non-enzymatic antioxidant defense glutathione. Our results strongly suggest that Cd and spermine treatments induce NO formation in wheat roots which, in turn, is involved in root growth inhibition.

Testosterone environment of splenocytes modifies the steroidogenesis of polycystic ovary in rats.

The functional relationship between the ovary and immune cells is well known. The modulation of ovarian steroidogenesis in adult rats with polycystic ovary (PCO) by secretions of cultured splenocytes treated with 10 (-6) M testosterone or 10 (-6) M testosterone plus 10 (-4) M flutamide, an androgen receptor antagonist, was investigated. Polycystic ovary was induced by estradiol valerate (2 mg/rat). Polycystic ovary splenocyte secretions decreased the release of androstenedione from PCO ovaries in contrast to the effect of non-PCO splenocyte secretions. This decrease was associated with a significant decrease in androgen receptor and IL-12 mRNA expression in PCO splenocytes. When splenocytes were treated with testosterone, their conditioned media further decreased androstenedione release from the ovary and had a greater inhibitory effect on PCO ovary compared with non-PCO ovary. This effect was reversed by flutamide. Polycystic ovary splenocytes showed a decrease in IL-1 beta mRNA expression. Their secretions scarcely affected progesterone release from non-PCO ovaries but significantly stimulated progesterone release from PCO ovary by an androgen-independent mechanism. The differential steroidogenic ability of splenocyte secretions from PCO rats is associated with the IN VITRO testosterone environment. Polycystic ovary splenocytes might exert a protective action against PCO effects through their secretions by inducing a low androstenedione response from the ovary.

Nutritional evaluation of commercial dry dog foods by near infrared reflectance spectroscopy.

Near infrared reflectance spectroscopy (NIRS) was used to predict the nutritional value of dog foods sold in Chile. Fifty-nine dry foods for adult and growing dogs were collected, ground and scanned across the visible/NIR range and subsequently analysed for dry matter (DM), crude protein (CP), crude fibre (CF), total fat, linoleic acid, gross energy (GE), estimated metabolizable energy (ME) and several amino acids and minerals. Calibration equations were developed by modified partial least squares regression, and tested by cross-validation. Standard error of cross validation (SE(CV)) and coefficient of determination of cross validation (SE(CV)) were used to select best equations. Equations with good predicting accuracy were obtained for DM, CF, CP, GE and fat. Corresponding values for and SE(CV) were 0.96 and 1.7 g/kg, 0.91 and 3.1 g/kg, 0.99 and 5.0 g/kg, 0.93 and 0.26 MJ/kg, 0.89 and 12.4 g/kg. Several amino acids were also well predicted, such as arginine, leucine, isoleucine, phenylalanine-tyrosine (combined), threonine and valine, with values for and SE(CV) (g/kg) of 0.89 and 0.9, 0.94 and 1.3, 0.91 and 0.5, 0.95 and 0.9, 0.91 and 0.5, 0.93 and 0.5. Intermediate values, appropriate for ranking purposes, were obtained for ME, histidine, lysine and methionine-cysteine. Tryptophan, minerals or linoleic acid were not acceptably predicted, irrespective of the mathematical treatment applied. It is concluded that NIR can be successfully used to predict important nutritional characteristics of commercial dog foods.