Shaping single crystalline BaTiO3nanostructures by focused neon or helium ion milling.

The realization of perovskite oxide nanostructures with controlled shape and dimensions remains a challenge. Here, we investigate the use of helium and neon focused ion beam (FIB) milling in an ion microscope to fabricate BaTiO3nanopillars of sub-500 nm in diameter starting from BaTiO3(001) single crystals. Irradiation of BaTiO3with He ions induces the formation of nanobubbles inside the material, eventually leading to surface swelling and blistering. Ne-FIB is shown to be suitable for milling without inducing surface swelling. The resulting structures are defect-free single crystal nanopillars, which are enveloped, on the top and lateral sidewalls, by a point defect-rich crystalline region and an outer Ne-rich amorphous layer. The amorphous layer can be selectively etched by dipping in diluted HF. The geometry and beam-induced damage of the milled nanopillars depend strongly on the patterning parameters and can be well controlled. Ne ion milling is shown to be an effective method to rapidly prototype BaTiO3crystalline nanostructures.

Probing photo-carrier collection efficiencies of individual silicon nanowire diodes on a wafer substrate.

Vertically aligned silicon nanowire (SiNW) diodes are promising candidates for the integration into various opto-electronic device concepts for e.g. sensing or solar energy conversion. Individual SiNW p-n diodes have intensively been studied, but to date an assessment of their device performance once integrated on a silicon substrate has not been made. We show that using a scanning electron microscope (SEM) equipped with a nano-manipulator and an optical fiber feed-through for tunable (wavelength, power using a tunable laser source) sample illumination, the dark and illuminated current-voltage (I-V) curve of individual SiNW diodes on the substrate wafer can be measured. Surprisingly, the I-V-curve of the serially coupled system composed of SiNW/wafers is accurately described by an equivalent circuit model of a single diode and diode parameters like series and shunting resistivity, diode ideality factor and photocurrent can be retrieved from a fit. We show that the photo-carrier collection efficiency (PCE) of the integrated diode illuminated with variable wavelength and intensity light directly gives insight into the quality of the device design at the nanoscale. We find that the PCE decreases for high light intensities and photocurrent densities, due to the fact that considerable amounts of photo-excited carriers generated within the substrate lead to a decrease in shunting resistivity of the SiNW diode and deteriorate its rectification. The PCE decreases systematically for smaller wavelengths of visible light, showing the possibility of monitoring the effectiveness of the SiNW device surface passivation using the shown measurement technique. The integrated device was pre-characterized using secondary ion mass spectrometry (SIMS), TCAD simulations and electron beam induced current (EBIC) measurements to validate the properties of the characterized material at the single SiNW diode level.

Large area fabrication of vertical silicon nanowire arrays by silver-assisted single-step chemical etching and their formation kinetics.

Vertically aligned silicon nanowire (SiNW) arrays have been fabricated over a large area using a silver-assisted single-step electroless wet chemical etching (EWCE) method, which involves the etching of silicon wafers in aqueous hydrofluoric acid (HF) and silver nitrate (AgNO3) solution. A comprehensive systematic investigation on the influence of different parameters, such as the etching time (up to 15 h), solution temperature (10-80 °C), AgNO3 (5-200 mM) and HF (2-22 M) concentrations, and properties of the multi-crystalline silicon (mc-Si) wafers, is presented to establish a relationship of these parameters with the SiNW morphology. A linear dependence of the NW length on the etch time is obtained even at higher temperature (10-50 °C). The activation energy for the formation of SiNWs on Si(100) has been found to be equal to ∼0.51 eV . It has been shown for the first time that the surface area of the Si wafer exposed to the etching solution is an important parameter in determining the etching kinetics in the single-step process. Our results establish that single-step EWCE offers a wide range of parameters by means of which high quality vertical SiNWs can be produced in a very simple and controlled manner. A mechanism for explaining the influence of various parameters on the evolution of the NW structure is discussed. Furthermore, the SiNW arrays have extremely low reflectance (as low as <3% for Si(100) NWs and <12% for mc-Si NWs) compared to ∼35% for the polished surface in the 350-1000 nm wavelength range. The remarkably low reflection surface of SiNW arrays has great potential for use as an effective light absorber material in novel photovoltaic architectures, and other optoelectronic and photonic devices.