RESUMEN
Fingerprint orientation field (OF) estimation is important for basic fingerprint image processing and impacts the accuracy of fingerprint image enhancements, such as Gabor filters. In this article, we introduce an OF estimation algorithm based on differential values of grayscale intensity and examine the accuracy and reliability of the proposed algorithm by applying it to fingerprint images processed using Gaussian blurring and the Gaussian white noise process. The experimental results indicate that the OF estimation reliability of the proposed algorithm is higher than the gradient-based method and the power spectral density (PSD) based method in low quality fingerprints. The proposed algorithm is especially useful in noisy fingerprint images, where the OF estimation reliability of the algorithm is 6.46% and 32.93% higher than the gradient-based method and the PSD-based method, respectively.
RESUMEN
The thermal stability of (Mg0.95Ni0.05)2TiO4 dielectric ceramics has been improved by mixing with CaTiO3 phases owing to higher positive temperature coefficients. The pure (Mg0.95Ni0.05)2TiO4 and the mixture phase systems of CaTiO3-modified (Mg0.95Ni0.05)2TiO4 were verified by XRD diffraction patterns to ensure the crystallite of different phases. The microstructures of the CaTiO3-modified (Mg0.95Ni0.05)2TiO4 were observed by SEM and EDS to investigate the relation between element ratios and grains. As a result, it can be seen that the thermal stability of the CaTiO3-modified (Mg0.95Ni0.05)2TiO4 can be effectively enhanced, compared with the pure (Mg0.95Ni0.05)2TiO4. Moreover, the radio frequency dielectric performances of CaTiO3-modified (Mg0.95Ni0.05)2TiO4 dielectric ceramics are strongly dependent upon the density and the morphology of the specimens. The champion sample with the ratio of (Mg0.95Ni0.05)2TiO4 and CaTiO3 of 0.92:0.08 showed an εr value of 19.2, an Qf value of 108,200 GHz, and a τf value of -4.8 ppm/°C, which may encourage (Mg0.95Ni0.05)2TiO4 ceramics to broaden the range of novel applications and match the requirements of 5G or next-generation communication systems.
RESUMEN
The microstructures and microwave dielectric properties of (Mg0.6Zn0.4)0.95Ni0.05TiO3 with Ca0.6La0.8/3TiO3 and Ca0.8Sm0.4/3TiO3 additions prepared by the solid-state method has been investigated. The crystallization and microstructures of these two mixed dielectrics were checked by XRD, EDX, BEI, and SEM to demonstrate two phase systems. Furthermore, the tunable dielectric properties can be achieved by adjusting the amounts of Ca0.6La0.8/3TiO3 and Ca0.8Sm0.4/3TiO3 additions, respectively. After optimization of processed parameters, a new dielectric material system 0.88(Mg0.6Zn0.4)0.95Ni0.05TiO3-0.12Ca0.6La0.8/3TiO3 possesses a permittivity (εr) of 24.7, a Qf value of 106,000 (GHz), and a τf value of 3.8 (ppm/°C), with sintering temperature at 1225 °C for 4 h. This dielectric system with a near-zero temperature coefficient and appropriate microwave properties revealed a high potential for high-quality substrates adopted in wireless communication devices.
RESUMEN
Mg0.95Ni0.05TiO3 ceramics were prepared by traditional solid-state route using sintering temperatures between 1300 and 1425 °C and holding time of 2-8 h. The sintered samples were characterized for their phase composition, micro-crystalline structure, unit-cell constant, and dielectric properties. A two-phase combination region was identified over the entire compositional range. The effect of sintering conditions was analyzed for various properties. Both permittivity (εr) and Q factor (Qf) were sensitive to sintering temperatures and holding times, and the optimum performance was found at 1350 °C withholding time of 4 h. The temperature coefficient of resonant frequency (τf) in a range from -45.2 to -52 (ppm/°C) and unit-cell constant were not sensitive to both the sintering temperature and holding time. An optimized Q factor of 192,000 (GHz) related with a permittivity (εr) of 17.35 and a temperature coefficient (τf) of -47 (ppm/°C) was realized for the specimen sintered at 1350 °C withholding time of 4 h. For applications of 5G communication device (filter, antennas, etc.), Mg0.95Ni0.05TiO3 is considered to be a suitable candidate for substrate materials.