High-resolution X-ray diffraction with no sample preparation.

It is shown that energy-dispersive X-ray diffraction (EDXRD) implemented in a back-reflection geometry is extremely insensitive to sample morphology and positioning even in a high-resolution configuration. This technique allows high-quality X-ray diffraction analysis of samples that have not been prepared and is therefore completely non-destructive. The experimental technique was implemented on beamline B18 at the Diamond Light Source synchrotron in Oxfordshire, UK. The majority of the experiments in this study were performed with pre-characterized geological materials in order to elucidate the characteristics of this novel technique and to develop the analysis methods. Results are presented that demonstrate phase identification, the derivation of precise unit-cell parameters and extraction of microstructural information on unprepared rock samples and other sample types. A particular highlight was the identification of a specific polytype of a muscovite in an unprepared mica schist sample, avoiding the time-consuming and difficult preparation steps normally required to make this type of identification. The technique was also demonstrated in application to a small number of fossil and archaeological samples. Back-reflection EDXRD implemented in a high-resolution configuration shows great potential in the crystallographic analysis of cultural heritage artefacts for the purposes of scientific research such as provenancing, as well as contributing to the formulation of conservation strategies. Possibilities for moving the technique from the synchrotron into museums are discussed. The avoidance of the need to extract samples from high-value and rare objects is a highly significant advantage, applicable also in other potential research areas such as palaeontology, and the study of meteorites and planetary materials brought to Earth by sample-return missions.

European consensus on the concepts and measurement of the pathophysiological neuromuscular responses to passive muscle stretch.

BACKGROUND AND PURPOSE: To support clinical decision-making in central neurological disorders, a physical examination is used to assess responses to passive muscle stretch. However, what exactly is being assessed is expressed and interpreted in different ways. A clear diagnostic framework is lacking. Therefore, the aim was to arrive at unambiguous terminology about the concepts and measurement around pathophysiological neuromuscular response to passive muscle stretch. METHODS: During two consensus meetings, 37 experts from 12 European countries filled online questionnaires based on a Delphi approach, followed by plenary discussion after rounds. Consensus was reached for agreement ≥75%. RESULTS: The term hyper-resistance should be used to describe the phenomenon of impaired neuromuscular response during passive stretch, instead of for example 'spasticity' or 'hypertonia'. From there, it is essential to distinguish non-neural (tissue-related) from neural (central nervous system related) contributions to hyper-resistance. Tissue contributions are elasticity, viscosity and muscle shortening. Neural contributions are velocity dependent stretch hyperreflexia and non-velocity dependent involuntary background activation. The term 'spasticity' should only be used next to stretch hyperreflexia, and 'stiffness' next to passive tissue contributions. When joint angle, moment and electromyography are recorded, components of hyper-resistance within the framework can be quantitatively assessed. CONCLUSIONS: A conceptual framework of pathophysiological responses to passive muscle stretch is defined. This framework can be used in clinical assessment of hyper-resistance and will improve communication between clinicians. Components within the framework are defined by objective parameters from instrumented assessment. These parameters need experimental validation in order to develop treatment algorithms based on the aetiology of the clinical phenomena.

Abnormality of standing posture improves in patients with bilateral spastic cerebral palsy following lower limb surgery.

OBJECTIVES: The degree of abnormality of the gait pattern of children with bilateral spastic cerebral palsy (BSCP) can be reduced by lower limb orthopaedic surgery. However, little attention is paid to the effects of surgery on standing posture. Here, we investigated the abnormality of standing posture in young people with BSCP as well as the effects of surgery on standing posture. METHODS: We have developed an index of standing posture, the Standing Posture Score (SPS), which is similar in composition to the gait profile score (GPS). We applied SPS retrospectively to 32 typically developing children and 85 children with BSCP before and after surgery to the lower limbs aimed at improving gait. We investigated the relationship between SPS and GPS before surgery and also the relationship between changes in these variables before and after surgery. RESULTS: SPS is significantly higher in young people with BSCP. SPS reduces after surgery and this reduction is correlated with the reduction in GPS. INTERPRETATION: Successful surgery improves the alignment of the lower limbs in BSCP in standing and may have a positive impact on the activities of daily living which depend on a stable and efficient standing posture.

Does sex influence outcome in ambulant children with bilateral spastic cerebral palsy?

To investigate the effect of sex on the phenotype of bilateral spastic cerebral palsy (CP) we reviewed the gait analysis data of 116 children (78 males, mean age 8 y 1 mo [SD 3 y 1 mo] and 38 females, mean age 8 y 9 mo [3 y 1 mo]) with bilateral spastic CP (Gross Motor Function Classification System [GMFCS] Levels I [four males, six females]; II [41 males, 19 females]; III [26 males, 12 females]; and IV [7 males, 1 female]) who had been referred for gait analysis to inform treatment. Although there were no differences between males and females in terms of gestational age, chronological age, or GMFCS level, males were more likely to have had nonoperative intervention before the referral (p=0.024), had a greater degree of knee flexion in stance phase when walking (p=0.003), and had a higher Gillette Gait Index (p<0.001) when compared with females. Males were also more likely to have surgery recommended on the basis of gait analysis (p<0.001). Sex seems to influence the development of the musculoskeletal system and mobility in ambulant children with bilateral spastic CP, and this may need to be considered when planning intervention or when assessing the outcome of intervention.

The outcome of surgical intervention for early deformity in young ambulant children with bilateral spastic cerebral palsy.

We reviewed the outcome in 24 children with bilateral spastic cerebral palsy aged seven years or younger for whom surgery was recommended between 1999 and 2005 following gait analysis. A total of 13 children (operative group) had surgery and the remaining 11 (control group) did not, for family or administrative reasons. The operative group had at least two post-operative gait analyses at yearly intervals, with eight children having a third and six children a fourth. The control group had a second analysis after a mean interval of 1.5 years (95% confidence interval 1.1 to 1.9). In the operative group, the Gillette gait index, the ranges of movement in the lower limb joint and knee extension in stance improved following surgery, and this was maintained overall at the second post-operative analysis. The minimum knee flexion in stance in the control group increased between analyses. These results suggest that surgical intervention in selected children can result in improvements in gait and function in the short to medium term compared with non-operative management.

The effect of serial casting on gait in children with cerebral palsy: preliminary results from a crossover trial.

Serial casting aims to improve an equinus gait pattern in children with spastic cerebral palsy (SCP). We evaluated the effect of short-term stretch casting on gait in children with SCP, compared to the natural history. A crossover trial, consisting of a control phase and a casting phase, was conducted with children randomised into two groups. Both groups were assessed clinically, and using 3D gait analysis, at 0, 5 and 12 weeks. Subjects in one group had the 3 month casting phase first and in the other had the 3 month control period first. Casts were changed weekly and set at maximum available ankle dorsiflexion. The mean changes at 5 weeks and 12 weeks from baseline measurements in the casting phase were compared with the change within the same time interval in the control phase. Significant improvements in passive ankle dorsiflexion (knee flexed) were found at 5 and 12 weeks. Passive ankle dorsiflexion (knee extended), ankle dorsiflexion in single support, ankle dorsiflexion in swing and minimum hip flexion in stance improved significantly at 5 weeks but not at 12 weeks from baseline. Other kinematic parameters, the score on the Gillette Functional Assessment Questionnaire, and maximum reported walking distance were not changed by casting. Casting to improve range appears to improve passive and dynamic ankle dorsiflexion, but the changes are small, short lived and do not appear to affect function.

Botulinum toxin and cerebral palsy: time for reflection?

Botulinum toxin A (BTX-A) is increasingly being used in early management of spasticity in ambulant children with cerebral palsy (CP), with the aim of improving function, promoting muscle growth, and delaying the need for surgical intervention. However, there is a lack of evidence about the long-term outcome of BTX-A injections. The focus on spasticity as the predominant problem in younger children with spastic CP may not fully consider the associated muscle weakness. It also raises concern that although BTX-A may improve function in the short term, it has the potential to affect muscle growth and function adversely in the long term. A cautious approach to the early use of BTX-A, with the use of objective outcome measures within a specialized multidisciplinary setting, is recommended, particularly in ambulant children with spastic diplegic CP, until further evidence is available on the long-term outcome of early BTX-A injections in children with CP.

Three-dimensional realisation of muscle morphology and architecture using ultrasound.

Two-dimensional B-mode ultrasound imaging and motion tracking were combined to generate three-dimensional reconstructions of the medial gastrocnemius. Architectural and morphological features of this muscle could be visualised. The length of the gastrocnemius belly was measured in normally (ND) developing children and in children with spastic diplegic cerebral palsy (SDCP) who had plantarflexion contractures. Using a random effects linear model we demonstrated that the gastrocnemius muscle bellies of children with SDCP were shorter than those of ND children (P = 0.001) even when corrected for ankle position. The technique described could be used to evaluate muscular deformity before and after an intervention.

Lower limb extensor moments in children with spastic diplegic cerebral palsy.

In this retrospective study, we quantified the mean extensor moment at the ankle, knee and hip over the stance period in a group of independently ambulant children with spastic diplegia (n = 90; 167 limbs) and in a group of normally-developing (ND) children (n = 22; 22 limbs). The mean knee extensor moment and the mean support moment demonstrated greater variance in children with diplegia than in normally-developing children (P < 0.0001 and P < 0.001). This was explained by a strong relationship between the mean knee extensor moment and minimum knee flexion in stance (r2 = 0.615; P < 0.0001) in the affected group with a positive mean knee extensor moment for all those children who walked in greater than 20 degrees of knee flexion. We also found a linear relationship between the support moment and knee flexion (r2 = 0.805; P < 0.0001). Our data supported the biomechanical analysis of Hof [Gait Posture, 12 (2000) 196] who suggested that his modified support moment should be a linear function with eccentricity at the knee. Extensor moments at the ankle (r2 = 0.001376; P = 0.641) and hip (r2 = 0.0860; P = 0.000168) bore weak relationships with increasing knee flexion even though there was a strong positive relationship between minimum knee flexion and minimum hip flexion (r2 = 0.316; P < 0.0001). We conclude that children with spastic diplegic cerebral palsy (SDCP) who walk with a crouch gait rely on their knee extensors to prevent collapse of the lower limbs. Intervention directed at redistributing extensor moments between the joints of the lower limbs may slow the increase in knee flexion and prolong reasonable walking function in this group.

Haemodynamic considerations in the design of a skeletal muscle ventricle.

Skeletal muscle ventricles (SMVs) configured to operate as diastolic counterpulsators show promise as cardiac assist devices. In four pigs, SMVs were connected to the aorta by a single-limbed conduit and activated during every third cardiac diastole. During the assisted beats, mean diastolic aortic pressure increased by 30.3 +/- 2.2%, peak diastolic aortic pressure increased by 38.5 +/- 2.7%, the endocardial viability ratio increased by 42.3 +/- 3.4%, and mean left anterior descending coronary artery flow increased by 61.6 +/- 4.5%. Although there are major advantages to making the connection to the aorta by a single-limb conduit, the lack of separation between inlet and outlet means that such devices must be designed carefully to avoid thrombogenesis under chronic conditions. Design rules were developed for this configuration, based on earlier in vitro studies. They addressed the problem of stasis by promoting the development of a propagating vortex that travels the length of the ventricle and ensured proper exchange of blood with the circulation by limiting the volume of the connecting conduit. An SMV compatible with these rules was connected in a pig. At elective termination 1 week later, activation of the SMV increased peak diastolic pressure by 20.1% and reduced left-ventricular stroke work in the post-assisted beat by 10.1%. The SMV was free from thrombus.

Accurate measurement of muscle belly length in the motion analysis laboratory: potential for the assessment of contracture.

Two-dimensional ultrasound imaging was combined with motion analysis technology to measure distances between remote anatomical landmarks. The length of the belly of the medial gastrocnemius muscle in five normal adults (nine limbs) was estimated using this technique. Our results in vivo were similar to the reported data for the lengths of muscles in cadavers, and were consistent with the expected relationship between muscle belly length and ankle joint angle. Experiments in vitro demonstrated that the accuracy of the device was better than 2 mm over 20 cm. Measurements on the same subject on different occasions showed that the results were repeatable in vivo. Rendering of the reconstructed volume of a foam phantom gave results comparable to photographic images. This validated technique could be used to measure muscle lengths in children with spastic cerebral palsy and indicate which muscles had fixed shortening, and to what extent.

Architecture of the medial gastrocnemius in children with spastic diplegia.

Ultrasound images were obtained of the medial gastrocnemius at different ankle joint positions with the knee extended. Fascicle length and deep fascicle angle were measured in five normally developing adults (mean age 33 years, age range 24 to 36 years) and in five normally developing children (mean age 7.8 years, age range 7 to 11 years), and in seven children with spastic diplegia (mean age 10 years, age range 6 to 13 years). These architectural variables were similar in the groups of normally developing adults and children. Importantly, no statistical difference could be found between the normally developing children and those with diplegia for fascicle length. Deep fascicle angles were reduced significantly in the clinical group at a particular ankle joint angle but not at the resting angles. The difference in deep fascicle angles is explained as a function of resting muscle length and is not attributed any clinical importance. Our results do not explain the structural origin of muscle contracture explicitly. However, they do indicate that most of the fixed shortness in the medial gastrocnemii of ambulant children with spastic diplegia is not due to reduced muscle fascicle length. We suggest that muscle contracture may be better explained in terms of shortness of the aponeuroses of pennate muscles, such as the medial gastrocnemius, through reduced muscle fascicle diameter.

Functional assessment of skeletal muscle ventricles after pumping for up to four years in circulation.

BACKGROUND: The successful treatment of cardiac failure by heart transplantation is severely limited by the shortage of donor organs, and alternative surgical approaches are needed. An experimental approach that holds considerable promise is the skeletal muscle ventricle (SMV), an auxiliary blood pump formed from a pedicled graft of latissimus dorsi muscle and connected to the circulation in a cardiac assist configuration. Adaptive transformation, or conditioning, by electrical stimulation enables the skeletal muscle to perform a significant proportion of cardiac work indefinitely without fatigue. METHODS: In 10 dogs, SMVs were constructed from the latissimus dorsi muscle, lined internally with pericardium, and conditioned by electrical stimulation to induce fatigue resistant properties. The SMVs were connected to the descending thoracic aorta via two 12-mm Gore-Tex conduits and the aorta was ligated between the two grafts. The SMV was stimulated to contract during the diastolic phase of alternate cardiac cycles. The animals were monitored at regular intervals. RESULTS: At initial hemodynamic assessment, SMV contraction augmented mean diastolic blood pressure by 24.6% (from 61 +/- 7 to 76 +/- 9 mm Hg). Presystolic pressure was reduced by 15% (from 60 +/- 8 to 51 +/- 7 mm Hg) after an assisted beat. Four animals died early, 1 from a presumed arrhythmia, and 3 during propranolol-induced hypotension. The other 6 animals survived for 273, 596, 672, 779, 969, 1,081, and 1,510 days. Diastolic augmentation was 27.4% at 1 year (93 +/- 9 vs 73 +/- 6 mm Hg; n = 5), 34.7% at 2 years (85 +/- 6 vs 63 +/- 7 mm Hg; n = 3), 21.2% (89 +/- 10 vs 73 +/- 8 mm Hg; n = 2) at 3 years, and 34.5% (78 vs 58 mm Hg; n = 1) after 4 years in circulation. After 4 years, the isolated SMV was able to maintain a pressure of over 80 mm Hg while ejecting fluid at 20 mL/s. No animal showed evidence of SMV rupture or thromboembolism. CONCLUSIONS: The SMVs in this study provided effective and stable hemodynamic assistance over an extended period of time. There was no evidence that the working pattern imposed on the muscular wall of the SMV compromised its viability. Areas of fibrofatty degeneration were suggestive of early damage that future protocols should seek to minimize.

Computer aided design and fabrication of models for in vitro studies of vascular fluid dynamics.

An integrated computer aided design/computer aided manufacture system has been used to model the complex geometry of blood vessel anastomoses. Computer models are first constructed with key dimensions derived from radiological images of bypass grafts, and from casts of actual blood vessel anastomoses. Physical models are then fabricated in one of two ways: the surface geometry data can be used to control the movement of a three-axis milling machine; alternatively, the same data can be exported in a form that can be interpreted by a stereolithography apparatus. Both methods produce geometrically defined solid investments that can be used in a multistep casting process that yields high-quality physical models for vascular fluid dynamic studies. This technique is useful for parametric studies.

Development of a simulator for endovascular repair of abdominal aortic aneurysms.

The design and development of a simulator for endovascular repair of abdominal aortic aneurysm (AAA) is described. The simulator consists of an interchangeable model of a human AAA based on computed tomography data and is produced by means of computer-aided design and manufacture (CAD/CAM) techniques. The model has renal, iliac, and femoral arteries, and is perfused with a temperature controlled blood-analog fluid under simulated physiological flow conditions. "Fluoroscopic imaging" is simulated by a computerized imaging system that uses visible light. A movable video camera relays images in the antero-posterior and lateral planes of the AAA to a monitor. The imaging system allows "arteriography" and "road-mapping" to be performed so as to facilitate accurate deployment of endovascular stent-grafts. The system has been used for teaching and demonstrating endovascular techniques to clinicians, as well as the evaluation of new stent-graft devices. Its successful incorporation into endovascular workshops has demonstrated its role in the training of clinicians in endovascular repair of AAA.

Sodium channel protein expression enhances the invasiveness of rat and human prostate cancer cells.

Expression of Na+ channel protein was analysed in established cell lines of rat and human prostatic carcinoma origin by flow cytometry using a fluorescein-labelled polyclonal antibody. In many cell lines examined, the obtained frequency distribution profiles were bimodal and identified a subpopulation of cells which expressed high levels of Na+ channel protein. A significant positive correlation was demonstrated between the proportion of channel-expressing cells and the functional ability of individual cell lines to invade a basement membrane matrix in vitro. In addition, two transfectant cell lines containing rat prostate cancer genomic DNA were found to express significantly elevated levels of Na+ channel protein when compared with the original benign recipient cell line. Enhanced Na+ channel expression by two metastatic derivatives of these transfectant cells directly correlated with increased invasiveness in vitro. These studies strongly support the hypothesis that expression of Na+ channel protein and the metastatic behaviour of prostatic carcinoma cells are functionally related, either by endowing the membranes of these cells with specialised electrophysiological properties (e.g. enhancing their motility and/or secretory activities) and/or by perturbing endogenous mechanisms regulating ionic homeostasis within the cells.

Platelet reactions to modified surfaces under dynamic conditions.

The influence of surfaces on the reactions of platelets in whole blood under laminar flow was investigated in a cone and plate viscometer. Citrated whole blood was exposed to steel, PMMA and PMMA modified with PEO at low (500 s(-1)) and high (4000 s(-1)) wall shear rates at room temperature for a period of 100 s. Treated blood samples were fixed with paraformaldehyde, stained with a monoclonal antibody for CD41 (platelet GPIIb/IIIa) conjugated with phycoerythrin and analyzed by flow cytometry. The reactions of platelets (microparticle generation and formation of platelet-platelet, platelet-red blood cell and red blood cell-microparticle aggregates) to these environments were quantified. Additionally, the size of platelet-platelet aggregates was assessed. The percentage platelet aggregation and numbers of microparticles generated were independent of surface type at any shear rate. The composition of the aggregates formed was influenced by the surface: at low and high shear rates PMMA caused the generation of platelet-platelet aggregates of the greatest size. The numbers of red blood cell-platelet and red blood cell-microparticle aggregates also varied depending on the surface. Fewer red blood cell-platelet aggregates were formed at higher shear rates, whereas the reverse was true for red blood cell-microparticle aggregates. It is concluded that these variations may help to explain the differential effects of surfaces to the induction of distant thrombotic events: microparticles may be protected from loss from the blood stream by their association with red blood cells at high shear rates.

Relation between muscle contraction speed and hydraulic performance in skeletal muscle ventricles.

BACKGROUND: The fatigue resistance and power-to-weight ratio of skeletal muscle that has been conditioned by electrical stimulation makes cardiac assistance from a graft of such muscle a realistic prospect. A skeletal muscle must be surgically reconfigured to act on the circulating blood, but little is known about the power losses that accompany such interventions. We investigated in acute experiments the hydraulic performance of approximately cylindrical pumps made from sheep latissimus dorsi (LD) muscles, having first characterized the performance of each muscle in situ. METHODS AND RESULTS: Force-length and force-velocity relations were measured in situ for LD that had received either 8 weeks of stimulation at 2 Hz or no chronic stimulation. Two sizes of skeletal muscle ventricle (SMV) were formed from the same muscles, and their hydraulic performance was measured. The hydraulic performance was also calculated from the linear data, models of the force-length and force-velocity curves, and a description of the stress distribution within the SMV wall. The model predicted well the isovolumetric function of the ventricles and the optimum afterload but overestimated the flow and therefore the power. In conditioned ventricles the performance was particularly poor because of the slow contractile properties of the muscles. CONCLUSIONS: If SMVs are to pump effectively against the arterial impedance, the pressure drop caused by flow (or the internal resistance) should be lower than that of the ventricles we constructed. Progress can be made through refinement of surgical technique and stimulation protocols that generate faster fatigue-resistant muscles.

Flow in a simple model skeletal muscle ventricle: comparison between numerical and physical simulations.

Flow patterns generated during ventricular filling have been investigated for three different combinations of flow rate and injection volume. The numerical solutions from a commercially available computational fluid dynamics package were compared with observations made under identical flow conditions in a physical model for the purpose of code validation. Particle pathlines were generated from the numerical velocity data and compared with corresponding flow-visualization pictures. A vortex formed at the inlet to the ventricle in both cases: During the filling phase, the vortex expanded and traveled toward the apex of the ventricle until, at the end of filling, the vortex occupied the full radial extent of the ventricle; the vortex continued to travel once the filling process had ended. The vortices in vitro were more circular in shape and occupied a smaller volume than those generated by the numerical model. Nevertheless, comparison of the trajectories of the vortex centres showed that there was good agreement for the three conditions studied. Postprocessing of velocity data from the numerical solution yielded wall shear-stress measurements and particle pathlines that clearly illustrate the mass-transport qualities of the traveling vortex structure. For the cases considered here, the vortex transit produced a time-dependent shear stress distribution that had a peak value of 20 dynes cm-2, with substantially lower levels of shear stress in those regions not reached by the traveling vortex. We suggest that vortex formation and travel could reduce the residence time of fluid within a skeletal muscle ventricle, provided that the vortex travels the complete length of the ventricle before fluid is ejected at the start of the next cycle.