Effect of fibrous separators on the performance of lithium-sulfur batteries.

In this paper we systematically investigated effect of separator morphology on the performance of Li-S batteries. We tested two kinds of commercially available non-woven fibrous separators made of polypropylene in conjunction with trilayer PP/PE/PP porous separator. Among the non-woven separators, the fibers of the separator of first kind are rough and more acidic than the fibers of the separator of second art, which are smooth. It was found that batteries with smooth separator demonstrate higher Coulombic efficiency, higher charging/discharging capacity and better cycling stability. We attribute better performance of batteries with smooth fibers of separators to lower acidity than that of rough fibers. We believe that negatively charged polysulfides are unable to adsorb on more acidic rough fibers and diffuse readily to lithium electrode. In contrast, polysulfides are able to adsorb on the surface of less acidic smooth fibers that reduces their polysulfides shuttle and rapid decay of battery capacity. Strategic deployment of non-woven Freudenberg and Celgard separator in combination leads to high active mass utilization, superior wettability, reduced short circuit tendency caused by dendritic growth and slower capacity decay.

Functional polyelectrolyte multilayer membranes for water purification applications.

A diverse set of supported multilayer assemblies with controllable surface charge, hydrophilicity, and permeability to water and solute was fabricated by pressure driven permeation of poly(sodium 4-styrenesulfonate) (PSS) and poly(diallyldimethylammonium chloride) (PDDA) solution through poly(ethylene terephthalate) (PET) track-etched membranes. The polyelectrolyte multilayer fabrication was confirmed by means of FTIR, SEM, AFM, ellipsometry, zetapotential, and contact angle characterization. The prepared membranes were characterized in terms of their pure water permeability, flux recovery, and resistance to organic and biofouling properties. The antifouling behavior of the membranes was assessed in terms of protein adsorption and antibacterial behavior. Finally, the membranes were tested for rejection of selected water soluble dyes to establish their usefulness for organic contaminant removal from water. The membranes were highly selective and capable of nearly complete rejection of congo red with sufficiently high fluxes. The feasibility of regenerating the prepared membranes fouled by protein was also demonstrated and good flux recovery was obtained. In summary, the multilayer approach to surface and pore modification was shown to enable the design of membranes with the unique combination of desirable separation characteristics, regenerability of the separation layer, and antifouling behavior.

[Coat changes in castrated bitches - a review of the literature]. / Haarveränderung nach Kastration bei der Hündin. Eine Übersicht der Literatur.

OBJECT: Literature on veterinary medicine was searched for information on coat changes in castrated bitches. The data obtained was evaluated according to criteria of evidence-based veterinary medicine, to gain an objective basis for the evaluation of this undesired spaying-induced effect. MATERIAL AND METHODS: The literature search was carried out via the search function of PubMed and of the "Deutsche Nationalbibliothek" (DNB). Furthermore, German journals were surveyed for relevant papers. RESULTS: A total of 16 publications concerning the subject were found: ten expert opinions, three case series and three cohort studies. CONCLUSION: Publications on "coat changes in castrated bitches" are rare. The contemporary literature is predominantly comprised of expert opinions and is therefore of little evidentiary value. CLINICAL RELEVANCE: Because coat changes following spaying in bitches are often described, dog owners should be informed about these possible secondary effects after spaying. Analysis of frequency and promotive factors with high evidentiary value are still lacking. Consequently, it is difficult or impossible to predict the individual risk of a dog developing coat changes.

Antifouling and antibiofouling pH responsive block copolymer based membranes by selective surface modification.

Antifouling and antibacterial membranes are prepared by selective surface modification of pH responsive polystyrene-b-poly(4-vinylpyridine) (PS-P4VP) diblock copolymers by quaternization and zwitterionization reactions on a P4VP moiety. Nanoporous membranes based on the self-assembly of 2-(4'-hydroxybenzeneazo) benzoic acid (HABA)-PS-P4VP supramolecular complexes and nonsolvent induced phase separation are first prepared and the surfaces are functionalized by crosslinking with diiodobutane vapors and reacting with propane sultone vapors at moderate temperature and under vacuum conditions. Selective functionalization of surfaces is carried out to enhance the antifouling and antibiofouling properties of the membrane and to retain its pH switching behavior. The membranes are thoroughly characterized by various instrumental techniques such as Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, quartz crystal microbalance, contact angle, etc. Antifouling and antibacterial properties are proven by analyzing the adsorption of bovine serum albumin protein and bacterial cell attachment and killing efficiency. The actual membrane performance is assessed in terms of water flux under different pressures and pHs and Congo red dye rejection efficiency.

Effects of thiamethoxam seed treatments on soybean aphid (Hemiptera: Aphididae) feeding behavior.

Since its discovery in North America in 2000, the soybean aphid, Aphis glycines Matsumura (Hemiptera: Aphididae), has rapidly become an important pest of soybean [Glycine max (L.) Merrill], sometimes resulting in significant yield losses. Previous research has documented the toxicity of neonicotinoid seed treatments to soybean aphids, but control under field conditions has been inconsistent. Imidacloprid, a popular neonicotinoid insecticide, has been shown to exhibit antifeedant effects on aphids. Antifeedant activity has not been demonstrated for other neonicotinoids, including thiamethoxam. This research investigated the effects of a thiamethoxam seed treatment on soybean aphid feeding behavior by using electronic penetration graphs (EPG) to visualize stylet penetration behavior. Soybean aphid feeding behavior was assessed for 9 h on thiamethoxam-treated and untreated soybeans (V2 and V4 stages). Because results were inconclusive from initial experiments, a study was conducted to document the effects of thiamethoxam-treated soybeans on soybean aphid survival. The seed treatment was shown to negatively affect aphid survival at 4, 8, and 11 d after aphid introduction. A subsequent EPG study then was designed to document soybean aphid feeding behavior for 15 h, after an initial exposure of 9 h to thiamethoxam-treated soybeans. In this study, the exposed aphids exhibited significant differences in feeding behavior compared with those aphids feeding on untreated soybeans. Soybean aphids on thiamethoxam-treated soybeans spent significantly less time feeding in the sieve element phase, with a greater duration of nonprobing events. These studies suggest soybean aphids are unable to ingest phloem sap, which may be another important element in seed treatment protection.

Intelligent materials with adaptive adhesion properties based on comb-like polymer brushes.

We investigated the adaptive adhesion properties of comb-like random copolymer brushes made of poly(ethylene glycol) (PEG)-poly(dimethylsiloxane) (PDMS) grafted on flat and rough substrates. The properties of the brush layers were investigated using ARXPS, contact angle, electrokinetics, null ellipsometry, and adhesion measurements. It was found that hydrophobic PDMS segments segregate at the brush topmost layer in the dry state. However, hydrophilic PEG chains segregate at the brush topmost layer in the wet state. The adhesion properties of fabricated materials were tested using the AFM colloid probe technique and probe tack tester. It was found that the adhesive properties depend strongly on the mechanical properties (stiff/soft) and chemical functionality (hydrophobicity/hydrophilicity) of the applied adhesion tester as well as on the chemical composition, surface roughness, and thickness of the brush. In particular, hydrophobic PDMS and hydrophilic PEG adhere more strongly to hydrophobically modified and hydrophilic native colloid probes, respectively. Thick brushes are more adhesive than thin ones, and brushes grafted to flat substrates are stickier than those grafted to rough substrates when measured with a hard AFM probe. Unlike the results of adhesion measurements performed using hard AFM probes, the PDMS surface probed by soft pressure-sensitive adhesives (PSA) is almost nonadhesive. However, PEG is strongly adhesive, and the adhesion increases with the PEG fraction in the brush when probed by both hydrophilic and hydrophobic soft adhesives. The surfaces roughness also has a considerable effect on adhesion. Contrary to the adhesion measurements performed by hard AFM colloid probes, the adhesion of rough surfaces measured with a soft PAA or SIS tack tester is greater than that on the corresponding flat one.

Microfluidic emulsion separation-simultaneous separation and sensing by multilayer nanofilm structures.

Emulsion separation is of high relevance for filtration applications, liquid-liquid-partitioning of biomolecules like proteins and recovery of products from droplet microreactors. Selective interaction of various components of an emulsion with substrates is used to design microfluidic flow chambers for efficient separation of emulsions into their individual components. Our lab-on-a-chip device consists of an emulsion separation cell with an integrated silicon sensor chip, the latter allowing the detection of liquid motion via the field-effect signal. Thus, within our lab-on-a-chip device, emulsions can be separated while the separation process is monitored simultaneously. For emulsion separation a surface energy step gradient, namely a sharp interface between the hydrophobic and hydrophilic parts of the separation chamber, is used. The key component of the lab-on-a-chip system is a multilayer and multifunctional nanofilm structure which not only provides the surface energy step gradient for emulsion separation but also constitutes the functional parts of the field-effect transistors. The proof-of-principle was performed using a model emulsion consisting of immiscible aqueous and organic solvent components. Droplet coalescence was identified as a key aspect influencing the separation process, with quite different effects during separation on open surfaces as compared to slit geometry. For a detailed description of this observation, an analytical model was derived and lattice Boltzmann computer simulations were performed. By use of grazing incidence small angle x-ray scattering (GISAXS) interfacial nanostructures during gold nanoparticle deposition in a flow field were probed to demonstrate the potential of GISAXS for in situ investigations during flow.

Structure and flow of droplets on solid surfaces.

The structure and flow of droplets on solid surfaces is investigated with imaging and scattering techniques and compared to simulations. To access nanostructures at the liquid-solid interface advanced scattering techniques such as grazing incidence small-angle x-ray scattering (GISAXS) with micro- and nanometer-sized beams, GISAXS and in situ imaging ellipsometry and GISAXS tomography are used. Using gold nanoparticle suspensions, structures observed in the wetting area due to deposition are probed in situ during the drying of the droplets. After drying, nanostructures in the wetting area and inside the dried droplets are monitored. In addition to drying, a macroscopic movement of droplets is caused by body forces acting on an inclined substrate. The complexity of the solid surfaces is increased from simple silicon substrates to binary polymer brushes, which undergo a switching due to the liquid in the droplet. Nanostructures introduced in the polymer brush due to the movement of droplets are observed.

Stability and dynamics of droplets on patterned substrates: insights from experiments and lattice Boltzmann simulations.

The stability and dynamics of droplets on solid substrates are studied both theoretically and via experiments. Focusing on our recent achievements within the DFG-priority program 1164 (Nano- and Microfluidics), we first consider the case of (large) droplets on the so-called gradient substrates. Here the term gradient refers to both a change of wettability (chemical gradient) or topography (roughness gradient). While the motion of a droplet on a perfectly flat substrate upon the action of a chemical gradient appears to be a natural consequence of the considered situation, we show that the behavior of a droplet on a gradient of topography is less obvious. Nevertheless, if care is taken in the choice of the topographic patterns (in order to reduce hysteresis effects), a motion may be observed. Interestingly, in this case, simple scaling arguments adequately account for the dependence of the droplet velocity on the roughness gradient (Moradi et al 2010 Europhys. Lett. 89 26006). Another issue addressed in this paper is the behavior of droplets on hydrophobic substrates with a periodic arrangement of square shaped pillars. Here, it is possible to propose an analytically solvable model for the case where the droplet size becomes comparable to the roughness scale (Gross et al 2009 Europhys. Lett. 88 26002). Two important predictions of the model are highlighted here. (i) There exists a state with a finite penetration depth, distinct from the full wetting (Wenzel) and suspended (Cassie-Baxter, CB) states. (ii) Upon quasi-static evaporation, a droplet initially on the top of the pillars (CB state) undergoes a transition to this new state with a finite penetration depth but then (upon further evaporation) climbs up the pillars and goes back to the CB state again. These predictions are confirmed via independent numerical simulations. Moreover, we also address the fundamental issue of the internal droplet dynamics and the terminal center of mass velocity on a flat substrate.

Dose-response relationships of clothianidin, imidacloprid, and thiamethoxam to Blissus occiduus (Hemiptera: Blissidae).

The western chinch bug, Blissus occiduus Barber (Hemiptera: Blissidae), has emerged as a serious pest of buffalograss, Buchlod dactyloides (Nuttall) Engelmann. In general, neonicotinoid insecticides effectively control a variety of turfgrass insects, particularly phloem-feeding pests. However, because of well documented inconsistencies in control, these compounds are generally not recommended for chinch bugs. This study was designed to document the contact and systemic toxicity of three neonicotinoid insecticides (clothianidin, imidacloprid, and thiamethoxam) to B. occiduus. In contact bioassays, thiamethoxam was approximately 20-fold less toxic than clothianidin or imidacloprid to B. occiduus nymphs and three-fold more toxic to adults. In adult systemic bioassays, thiamethoxam was up to five-fold more toxic than clothianidin or imidacloprid. Interestingly, thiamethoxam was significantly more toxic to adults than to nymphs in both contact and systemic bioassays. This was not observed with clothianidin or imidacloprid. Bifenthrin, used for comparative purposes, exhibited 1844-fold and 122-fold increase in toxicity to nymphs and adults, respectively. These results provide the first documentation of the relative toxicity of these neonicotinoid insecticides to B. occiduus.

[Experiences of career support and career obstacles in young physicians--results of a Swiss longitudinal study]. / Karriereförderliche und karrierehinderliche Erfahrungen in der Weiterbildungszeit junger Arztinnen und Arzte. Ergebnisse einer Schweizer Longitudinalstudie

BACKGROUND AND OBJECTIVES: Postgraduate education after medical school plays an important role in the career development of young doctors. This study investigated what supporting and obstructing factors help or hinder the of young doctors during their specialty training. METHODS: As part of a broader prospective study on determinants of career development of young doctors which had started in 2001, 529 participants were investigated in 2009 regarding the most important career-relevant factors experienced during their specialty training. Content analysis was used to assign the answers given to open questions to inductively defined categories RESULTS: The 1301 answers given about career-supporting factors and the 1047 answers given about career-hindering factors were assigned to 9 and 12 categories respectively. These categories were divided into internal and external career-relevant factors. Important factors relative to career enhancement were career support by superiors and high achievement motivation, followed by good professional qualifications and beneficial working conditions. The answers given in these four categories accounted for two thirds of all mentioned career supporting factors. Regarding career barriers, the four categories with the highest number of answers were lack of career support, unfavourable work-place conditions, extraprofessional concerns and labour market conditions. Significant gender differences were only be found regarding career-hindering factors: Female doctors mentioned more often mentioned concerns and gender-related barriers, while male doctors more often reported labour market conditions and unfavourable personality traits for influencing career advancement. CONCLUSIONS: Career promotion should be provided in a continuous, structured and institutionalized way to make better use of the potential of well trained doctors. The new generation of doctors should not only advocate better professional conditions but also be aware of barriers within themselves that have an impact on their career development.

Growing rate of gain on subsequent feedlot performance, meat, and carcass quality of beef steers.

Eighty Angus and Angus x Simmental steer calves were used in a completely random design to determine the effect of rate of BW gain during the backgrounding period on subsequent feedlot performance, carcass characteristics, Warner-Bratzler shear force (WBSF), and sensory analysis. Animals were stratified by BW and allotted randomly to 1 of 10 pens (5 pens/treatment). Dietary treatments were formulated for an ADG of 0.91 kg/d [low BW gain (LG), 1.06 Mcal of NE(g)/kg] diets and 1.25 kg/d [high BW gain (HG), 1.19 Mcal of NE(g)/kg]. Steers were fed 70 d during the growing period. The LG diet consisted of 52.5% barley silage, 39.0% whole shell corn, and 8.5% supplement, whereas the HG diet contained 43.9% barley silage, 47.4% whole shell corn, and 8.7% supplement (DM basis). Initial BW (226 kg) was not different (P = 0.70) between treatments. Steers fed the HG diet had increased ADG (1.67 vs. 1.40 kg/d; P < 0.001) compared with steers fed LG diet. Dry matter intake was greater (9.49 vs. 8.35 kg/d; P < 0.001) for steers fed the HG vs. LG diet. Total backgrounding cost ($/animal) was less (P < 0.001) for those steers fed LG diet compared with HG diet ($126.00 vs. $140.35, respectively); however, total cost per kilogram of BW gain was not different (P = 0.24; $0.485/kg of BW gain). After the backgrounding period, steers were fed a common finishing diet for 135 d. During the finishing period, LG steers had similar (P = 0.12; 10.73 vs. 10.35 kg/d) DMI compared with those fed HG diets; however, ADG was not different (1.55 kg; P = 0.72) among treatments. Hot carcass weight, marbling score, 12th-rib fat, LM area, and USDA yield grade were not different (P > 0.12) between treatments and averaged 363 kg, Sm(30), 1.33 cm, 83.8 cm(2), and 2.7, respectively. There were no differences (P = 0.77; 3.63 +/- 0.12 kg) in WBSF tenderness of rib-eye steaks. Percent cooking loss was increased in LG diets (P = 0.017). No differences were observed in consumer sensory analysis of tenderness, juiciness, and flavor intensity (P > or = 0.276; 5.43 +/- 0.12, 5.07 +/- 0.13, and 5.17 +/- 0.05, respectively). These data suggest that feeding steers diets that differ in energy concentration and result in ADG of 1.4 and 1.7 kg/d during the growing period results in minimal changes in subsequent finishing performance and does not affect meat quality.

[Future family physicians - reasons for their specialty choice and crucial professional skills]. / Zukünftige Hausärztinnen und Hausärzte - Gründe für die Berufswahl und berufliche Kernkompetenzen.

PURPOSE: The aim of the present study was to investigate the motivation of young physicians to work in family medicine/general practice and the skills to be acquired during residency. METHODS: As part of a prospective study on career determinants in young physicians starting in 2001, 84 future family physicians at the end of their residency were asked about their motivation for specialty choice and about core competencies in general practice. Content analysis was applied to assign the answers given to open questions to inductively defined categories. RESULTS: The 254 answers concerning the motivation for specialty choice of general medicine or general internal medicine, and the 375 answers concerning core competencies of a family physician were assigned to eleven categories. The most frequently named motives fall into the categories <>, <>, <>, <> and <>. The most frequently named core competencies fall into the categories <>, <> and <>. CONCLUSION: Motivation for working in general practice and the core competencies to be acquired stand for a patient centered conception of the medical profession. They also imply personal responsibility and latitude in medical practice.

[Work stress, health and satisfaction of life in young doctors. Results of a longitudinal study in Switzerland]. / Arbeitsstress, Gesundheit und Lebenszufriedenheit junger Arztinnen und Arzte. Ergebnisse einer Schweizer Longitudinalstudie.

BACKGROUND AND OBJECTIVES: Based on the Effort-Reward-Imbalance Model by Siegrist a study was undertaken to find out (a) in what way young doctors assess effort and reward during their specialist training; (b) whether there are certain job stress patterns over time; and (c) what the correlations are, if any, between perceived job stress, health and satisfaction with life. METHODS: Within the framework of a prospective study (2001 - 2007) 370 doctors who had just qualified and were residents in the German-speaking part of Switzerland were assessed four times by means of anonymized questionnaires. Job stress, measured by the Effort-Reward-Imbalance scale, as well as health and satisfaction with life were assessed in these doctors' 2nd (T2), 4th (T3), and 6th (T4) year of specialist training ("residents"). Stress patterns of the participants were evaluated, based on the effort and reward scale values at T2, T3, and T4, by two-step cluster analysis. Gender differences between the clusters were calculated by the 2 test and differences in the continuous variables by analysis of variance with repeated measurements. RESULTS: During residency the percentage of doctors who experienced an Effort-Reward-Imbalance (ratio between effort and reward ERI > 1) increased from 18% at T2 to 20 % at T3 to 25 % at T4. The cluster analysis revealed two clusters: Type 1 (67%) with effort values below average and reward values above average (ER balance) across the three measurement points, and type 2 (33 %) with effort values above average and reward values below average (ER imbalance). Subjects in cluster 2 showed unfavorable values, when compared with those in cluster 1, in overcommitment, in workload and in the health variables (anxiety, depression, physical and psychological well-being), as well as in their assessed satisfaction with life at all three measurement points. CONCLUSIONS: One third of the doctors experienced stress at work, caused by an effort-reward imbalance. This had a negative impact on their health and satisfaction with life. Regular supervision and goal-oriented career counselling provided by senior physicians could contribute to young doctors not feeling so much stressed at work, feeling well and being more content with their work.

Switchable photoluminescence of CdTe nanocrystals by temperature-responsive microgels.

In the present study, we report a method for preparing a fluorescent thermosensitive hybrid material based on monodisperse, thermosensitive poly( N-isopropyl acrylamide) (PNIPAM) microgels covered with CdTe nanocrystals of 3.2 nm diameter. The CdTe nanocrystals were covalently immobilized on the surface of PNIPAM microgels. The chemical environment around the CdTe nanocrystals was modified by changing the temperature and inducing the microgel volume-phase transition. This change provoked a steep variation in the nanocrystal photoluminescence (PL) intensity in such a way that when the temperature was under the low critical solution temperature (LCST) of the polymer (36 degrees C) the PL of the nanocrystals was strongly quenched, whereas above the LCST the PL intensity was restored.

[Young physicians' view on factors that increase the attractiveness of general practice]. / Möglichkeiten zur Attraktivitätssteigerung der Hausarztmedizin aus der Sicht junger Arztinnen und Arzte.

PURPOSE: The objectives of this study are to investigate young physicians' career plans at the end of their residency, and to assess what factors contribute in their view to improve the image of family medicine/general practice and make it an attractive career goal. METHODS: As part of a prospective study on career determinants in young physicians, begun in 2001, 534 residents were asked in 2007 about their aspired to professional career, their planned model of private practice, arguments against or for family medicine/general practice, respectively, and factors to improve the attractiveness of the latter. RESULTS: Of the study sample, 84 participants (42% men, 58% women) decided on family medicine (60% specialise in primary care, 40% in general internal medicine), 450 specialise in other medical specialties. Of the 534 study participants, 208 plan to work in a private practice, mostly in a group practice (88%). Of the future family physicians, 49% want to open their practice in an urban area, of the future specialists the respective number is 77%. Main reasons not to decide on family medicine are the uncertain development in health policy and the low income. The diversity of work, the broad spectrum of patients and the continuity in the doctor-patient relationship are named as factors in favour of family medicine. The possibility to run interdisciplinary group practices and better financial conditions are crucial factors to make family medicine an attractive career goal for young physicians. CONCLUSIONS: Family medicine is still assessed as an interesting field, however, the conditions of work as a family physician/general practitioner have a deterrent effect on young physicians.

Self-supported particle-track-etched polycarbonate membranes as templates for cylindrical polypyrrole nanotubes and nanowires: an X-ray scattering and scanning force microscopy investigation.

Self-supported particle-track-etched polycarbonate membranes with nearly perfect cylindrical pores are used for the preparation of similarly perfect cylindrical polypyrrole nanowires and nanotubes. A complete investigation of the structural properties that result at different stages of the preparation route of polypyrrole nanowires and nanotubes is based on a combination of real and reciprocal space techniques. Nanoporous membranes with nominal pore size ranging from 5 to 150 nm and pore density up to 10(9) pores/cm(2) made from 21-microm-thick polycarbonate films are used. Polypyrrole nanotubes or nanowires are synthesized inside the pores. A real-space picture of the nanomaterial results from scanning force microscopy (SFM) on ultrathin sections made in two directions to obtain structures in the sample surface as well as perpendicular to the surface. From a model-based fit to the small-angle and ultra-small-angle X-ray scattering (SAXS/USAXS) data, the geometric pore structure is obtained and compared to values determined with scanning electron microscopy (SEM). Nanopores, nanowires, and nanotubes are described by uniform solid cylinders or hollow tubes, which are oriented highly parallel to each other and exhibit a small size distribution. Below a critical pore diameter, solid nanowires are produced whereas above this limit hollow nanotubes result.

Supported particle track etched polyimide membranes: a grazing incidence small-angle X-ray scattering study.

Particle track etched polyimide membranes on silicon substrates covered with a native oxide layer are investigated. Preparation steps similar to the common classical particle track etched membrane production, giving rise to free-standing membranes, are successfully applied to the supported membranes. Polyimide films are used as a starting material for a template preparation based on high energy ion irradiation. The film/membrane structure is probed at different length scales by grazing incidence small-angle X-ray scattering at each individual preparation step. In addition, characterization with atomic force microscopy, variable-angle spectroscopic ellipsometry, Fourier transform infrared transmission, and attenuated total reflection spectroscopy is performed. An amount of 6 +/- 1 vol % pores inside the polyimide film is detected. The pores are oriented perpendicular to the substrate surface and have a conical shape, yielding a slightly reduced pore size at the substrate/film interface.

Contact angle hysteresis: study by dynamic cycling contact angle measurements and variable angle spectroscopic ellipsometry on polyimide.

The phenomenon of contact angle hysteresis was studied on smooth films of polyimide, a polymer type used in the microelectronic industry, by dynamic cycling contact angle measurements based on axisymmetric drop shape analysis-profile in combination with variable angle spectroscopic ellipsometry (VASE). It was found that both advancing and receding contact angles became smaller with increasing the number of cycles and are, therefore, not a property of the dry solid alone. The changes of the wetting behavior during these dynamic cycling contact angle measurements are attributed mainly to swelling and/or liquid retention. To reveal the water-induced changes of the polymer film, the polyimide surface was studied before and after the contact with a water droplet by VASE. Both the experimental ellipsometric spectrum for Delta and that for Psi as well as the corresponding simulations show characteristic shifts due to the contact with water. The so-called effective medium approximation was applied to recover information about the thickness and effective optical constants of the polymer layer from the ellipsometrically measured values of Delta and Psi. On the basis of these results, the swelling and retention behavior of the polyimide films in contact with water droplets were discussed.

Dependence of young female volleyballers' performance on their body build, physical abilities, and psycho-physiological properties.

AIM: The aim of the study was to establish which anthropometric characteristics, physical abilities and psycho-physiological properties determine the success of adolescent female volleyballers at competitions. METHODS: For this purpose we studied 32 female volleyballers aged 13-16 years. The anthropometric examination included 43 measurements, 7 tests of physical fitness, and 4 series of computerised psycho-physiological tests (n=21). The performance of game elements was measured empirically during championship games using the original computer program "Game". RESULTS: The proficiency of performing volleyball elements - serve, reception, feint, block and spike - was calculated by regression models from the 14 anthropometric measurements, 4 physical fitness and 7 psychophysiological test results, which showed significant correlation with proficiency in the game. The predictive power of the models was at least 32% and in average 56%. The anthropometric factor was significant in the performance of all the elements of the game, being most essential (71-83%) for attack, block and feint. Good results in physical ability tests granted success in serve, attack and reception. CONCLUSION: It was possible to predict the efficiency of reception (44%) by endurance, flexibility and speed measuring tests. Medicine ball throwing test was essential for attack (22%). Psycho-physiological tests were significant for the performance of block (98%), attack (80%), feint (60%) and reception (39%).