RESUMEN
This Letter presents what is to our knowledge a novel approach to reduce the digital signal processing (DSP) complexity in intensity modulation and direct detection (IM/DD) systems, which is critical for short-reach optical communication systems with severe bandwidth limitations. We propose a sub-baud rate sampling reception method utilizing a polyphase feedforward equalizer-based maximum likelihood sequence estimation (PFFE-MLSE), which could operate effectively under a sampling rate of 0.6 samples per symbol. This new architecture eliminates the need for resampling, allowing the adaptive equalizer to operate with significantly reduced complexity-over 60% compared to traditional FFE-MLSE. An offline experiment, transmitting a 100-Gbaud on-off keying (OOK) signal over a 5-km single-mode fiber (SMF) link, demonstrates the feasibility of our approach with bit error ratio (BER) meeting the KP4-forward error correction (KP4-FEC) threshold in the optical back-to-back (OBTB) scenario and 7% hard-decision FEC (HD-FEC) threshold in the 5-km SMF transmission.
RESUMEN
In this study, a novel magnetic Ni-Fe2O3-C catalyst combined with electromagnetic induction heating in biomass steam gasification was proposed to enhance H2 production. Better catalytic performance for H2 production was observed with the Ni-Fe2O3-C catalyst under induction heating, resulting in an increase in H2 yield from 735.1 to 2271.2 mL/g-biomass (a 209.1 % enhancement). SEM, TGA and XRD analysis demonstrated a significant decrease in coking deposition, caking, and particle agglomeration of the Ni-Fe2O3-C catalyst under induction heating, while maintaining more active sites. Importantly, the benefits of induction heating were also applicable to different magnetic catalysts like Ni-Al2O3-C, Ni-ZrO2-C, and Ni-MgO-C. Experimental results revealed a logarithmic correlation between the increase in H2 yields due to induction heating and the magnetic saturation (Ms) of the catalysts. The Ni-Fe2O3-C catalyst, with a high Ms of 50.9 emu/g, showed the highest catalytic activity for H2 production under induction heating in this study.
Asunto(s)
Biomasa , Compuestos Férricos , Hidrógeno , Níquel , Vapor , Catálisis , Hidrógeno/química , Níquel/química , Compuestos Férricos/química , Calor , Calefacción , Difracción de Rayos X , Fenómenos ElectromagnéticosRESUMEN
In this paper, the tribological characteristics of an oil-soluble magnetic fluid additive under mixed lubrication are studied by experiments and numerical simulation. [bmim][FeCl4] is dissolved in CF10W-40 lubricating oil as a magnetic liquid additive, and its friction coefficient is tested by a point contact friction tester at different temperatures, rotational speeds and magnetic field intensities. The transition condition of lubrication state is obtained through analyzing the Stribeck curves based on the experiments, and the strength model of boundary film is established accordingly. A mixed lubrication model is established by substituting the boundary film strength model and the surface roughness model into the hydrodynamic lubrication model based on Reynolds equation. The results show that the magnetic solution as an additive can obviously reduce friction and wear, and the effect is more obvious under the condition of magnetic field. The boundary film strength model can accurately reflect the transition characteristics of lubrication state in the presence of boundary film, and the mixed lubrication model based on boundary film strength model can more precisely reflect the tribological characteristics of friction pairs, so this study provides a new theoretical method for the related research on the influence of boundary film on lubrication characteristics.
RESUMEN
The optical fiber distributed strain sensor based on the optical frequency domain reflectometer (OFDR) preserves its dominant position in short-distance measurement fields with high spatial resolution, such as biomedical treatment, soft robot, etc. However, owing to the weak intensity of the Rayleigh backscattered signal (RBS) in the single-mode fiber (SMF) and complex computation, the large strain changes cannot be precisely and rapidly demodulated by the traditional cross-correlation method. In this work, the OFDR with backscattering enhanced optical fiber (BEOF) is proposed and demonstrated for fast and large strain measurement. By enhancing the RBS amplitude, the signal-to-noise ratio (SNR) is improved, resulting in a higher similarity between the reference signal and test signal, which is beneficial for the expansion of the strain measurement range. Moreover, the adaptive local feature extraction and matching (ALFEM) algorithm is presented and demonstrated, which replaces the traditional cross-correlation method for strain demodulation and fast measurement. On account of the enhancement ratio of BEOF, the dominant characteristic data segment can be extracted from whole wavelength data. In the experiments, the enhancing ratio of BEOF is designed as 10, resulting in the spatial resolution reaches 400µm and the strain measurement range is greatly increased to 4800µÉ. Further, the effectiveness of the ALFEM algorithm has been verified, in which the strain demodulation time is approximately 25% of that of the traditional method. This scheme fully exploits the enhancement characteristic of the BEOF and is also applicable to the systems based on other types of BEOF, different strain changes and sensing distances.
RESUMEN
Silicon (Si) anode has attracted broad attention because of its high theoretical specific capacity and low working potential. However, the severe volumetric changes of Si particles during the lithiation process cause expansion and contraction of the electrodes, which induces a repeatedly repair of solid electrolyte interphase, resulting in an excessive consuming of electrolyte and rapid capacity decay. Clearly known the deformation and stress changing at µÎµ resolution in the Si-based electrode during battery operation provides invaluable information for the battery research and development. Here, an in operando approach is developed to monitor the stress evolution of Si anode electrodes via optical fiber Bragg grating (FBG) sensors. By implanting FBG sensor at specific locations in the pouch cells with different Si anodes, the stress evolution of Si electrodes has been systematically investigated, and Δσ/areal capacity is proposed for stress assessment. The results indicate that the differences in stress evolution are nested in the morphological changes of Si particles and the evolution characteristics of electrode structures. The proposed technique provides a brand-new view for understanding the electrochemical mechanics of Si electrodes during battery operation.
RESUMEN
As a pivotal element in market mechanisms, carbon trading is increasingly recognized as crucial for achieving China's Carbon Peaking and Carbon Neutrality Goals. This study introduces a comprehensive dynamic model, integrating carbon trading, emissions, economic growth, and green technology innovation, to offer a holistic understanding of the interplay between these domains. Utilizing principles from nonlinear dynamics and chaos theory, the model is adept at simulating various scenarios and assessing the effectiveness of government policies in stabilizing these complex systems. In-depth analysis provided by this research sheds light on the nuanced impact of carbon trading policies on sustainable development. Key findings highlight (1) Carbon trading's essential role as a catalyst in propelling sustainable and high-quality growth. (2) A strong positive relationship is observed between the sophistication of the carbon trading mechanism and its effectiveness in stimulating green technology innovation and fostering high-quality green development. Notably, carbon trading's influence on green technology innovation markedly enhances the efficacy of carbon emission reduction strategies. (3) Government regulations are instrumental in augmenting carbon prices, thus incentivizing increased corporate participation in emission reduction and enhancing the overall impact of carbon emission reduction. Nevertheless, the study identifies a critical threshold in regulatory intensity, beyond which there is a risk of system destabilization ( a 3 ≥ 0.032 ). These findings underscore the imperative for developing an integrated national carbon emission trading market, prioritizing sustainable growth strategies and diligently pursuing China's environmental objectives.
Asunto(s)
Carbono , Desarrollo Económico , Gobierno , Regulación Gubernamental , Dinámicas no Lineales , ChinaRESUMEN
A fiber Bragg grating (FBG) displacement sensor based on synchronous sensing is developed for real-time monitoring of a tunnel lining. The sensing principle and mechanical structure of the proposed sensor are analyzed and simulated, and its sensitization effectiveness and temperature compensation are verified. Equivalent model tests show that the sensor has a good linear sensitivity of 19.48 pm/mm and an excellent precision of 5.13×10-2 m m in the displacement range of 0-25 mm, which is basically consistent with the simulation results. The key traffic parameters of the train were successfully obtained by real-time monitoring of the tunnel lining in a field trial, which shows the superior capability of micro-displacement measurement of the sensor. Furthermore, good stability and excellent creep resistance have also been demonstrated. Our results provide theoretical guidance for the fabrication and package of the FBG displacement sensor, which is valuable for structure health monitoring (SHM) in civil engineering applications.
RESUMEN
Mode-locked lasers with ultra-narrow spectral widths and durations of hundreds of picoseconds can be versatile light sources for a variety of newly emergent applications. However, less attention seems to be given to mode-locked lasers that generate narrow spectral bandwidths. We demonstrate a passively mode-locked erbium-doped fiber laser (EDFL) system that relies on a standard fiber Bragg grating (FBG) and the nonlinear polarization rotation (NPR) effect. This laser achieves the longest reported pulse width (to the best of our knowledge) of 143 ps based on NPR and an ultra-narrow spectral bandwidth of 0.017â nm (2.13â GHz) under Fourier transform-limited conditions. The average output power is 2.8â mW, and the single-pulse energy is 0.19 nJ at a pump power of 360â mW.
RESUMEN
Although parthenogenesis is widespread in nature and known to have close relationships with bisexuality, the transitional mechanism is poorly understood. Artemia is an ideal model to address this issue because bisexuality and "contagious" obligate parthenogenesis independently exist in its congeneric members. In the present study, we first performed chromosome spreading and immunofluorescence to compare meiotic processes of Artemia adopting two distinct reproductive ways. The results showed that, unlike conventional meiosis in bisexual Artemia, meiosis II in parthenogenic Artemia is entirely absent and anaphase I is followed by a single mitosis-like equational division. Interspecific comparative transcriptomics showed that two central molecules in homologous recombination (HR), Dmc1 and Rad51, exhibited significantly higher expression in bisexual versus parthenogenetic Artemia. qRT-PCR indicated that the expression of both genes peaked at the early oogenesis and gradually decreased afterward. Knocking-down by RNAi of Dmc1 in unfertilized females of bisexual Artemia resulted in a severe deficiency of homologous chromosome pairing and produced univalents at the middle oogenesis stage, which was similar to that of parthenogenic Artemia, while in contrast, silencing Rad51 led to no significant chromosome morphological change. Our results indicated that Dmc1 is vital for HR in bisexual Artemia, and the deficiency of Dmc1 may be correlated with or even possibly one of core factors in the transition from bisexuality to parthenogenesis.
Asunto(s)
Artemia , Recombinasas , Animales , Femenino , Recombinasas/genética , Artemia/genética , Artemia/metabolismo , Bisexualidad , Meiosis , Proteínas de Ciclo Celular/genética , Proteínas de Ciclo Celular/metabolismo , Partenogénesis/genética , Recombinasa Rad51/genética , Recombinasa Rad51/metabolismoRESUMEN
To survive under harsh environments, embryonic development of Artemia was arrested at the gastrula stage and released as the diapause embryo. Cell cycle and metabolism were highly suppressed in this state of quiescence. However, cellular mechanisms underlying diapause remain largely unclear. In this study, we found that the expression level of a CT10 regulator of kinase-encoding gene (Ar-Crk) in diapause embryos was significantly lower than non-diapause embryos at the early embryogenetic stage of Artemia. Knockdown of Ar-Crk by RNA interference induced formation of diapause embryos, while the control group produced nauplii. Western blot analysis and metabolic assays revealed that the diapause embryos produced by Ar-Crk-knocked-down Artemia had similar characteristics of diapause markers, arrested cell cycle, and suppressed metabolism with those diapause embryos produced by natural oviparous Artemia. Transcriptomic analysis of Artemia embryos revealed knockdown of Ar-Crk induced downregulation of the aurora kinase A (AURKA) signaling pathway, as well as energetic and biomolecular metabolisms. Taken together, we proposed that Ar-Crk is a crucial factor in determining the process of diapause in Artemia. Our results provide insight into the functions of Crk in fundamental regulations such as cellular quiescence.
Asunto(s)
Artemia , Diapausa , Animales , Artemia/genética , Regulación hacia Abajo , Diapausa/genética , División Celular , Ciclo Celular , Embrión no Mamífero/metabolismoRESUMEN
For the influence of boundary film on the lubrication state of sliding friction pairs, a boundary film strength model was proposed that can comprehensively reflect the influences of film thickness, pressure, shear stress and temperature. The model parameters were obtained through fitting the test results. Then, a mixed lubrication model considering boundary film strength was established by coupling the boundary film strength model with the hydrodynamic lubrication model and the asperity contact model. The calculation program was developed using the Fortran language, which can effectively capture the tribological characteristics and action ratios of the fluid, boundary film and dry friction components. Simultaneously, the mixed lubrication model was applied to the journal bearing. A parametric analysis was performed to investigate the influences of different working conditions on lubrication performance. Under current operating conditions, the results show that: when the speed is above 200 r/min or the viscosity is higher than 0.09 Pa·s, the boundary film breakdown rate is almost 0 and the friction coefficient is lower than 0.02; when the roughness is reduced from 1.8 µm to 0.8 µm, the ultimate load of the journal bearing rises from 27 MPa to 36 MPa, an increase of about 33%; when the load exceeds 36 MPa or the temperature is higher than 100 °C, more than 25% of the boundary film breaks and the dry friction component accounts for more than 60% of the total friction, which leads to a sudden increase in the friction coefficient. Hence, the study of mixed lubrication considering boundary film strength provides theoretical guidance for accurately reflecting the actual lubrication state and improving the mechanical energy efficiency of friction pairs.
RESUMEN
Doublesex (DSX) proteins are members of the Doublesex/mab-3-related (DMRT) protein family and play crucial roles in sex determination and differentiation among the animal kingdom. In the present study, we identified two Doublesex (Dsx)-like mRNA isoforms in the brine shrimp Artemia franciscana (Kellogg 1906), which are generated by the combination of alternative promoters, alternative splicing and alternative polyadenylation. The two transcripts exhibited sex-biased enrichment, which we termed AfrDsxM and AfrDsxF. They share a common region which encodes an identical N-terminal DNA-binding (DM) domain. RT-qPCR analyses showed that AfrDsxM is dominantly expressed in male Artemia while AfrDsxF is specifically expressed in females. Expression levels of both isoforms increased along with the developmental stages of their respective sexes. RNA interference with dsRNA showed that the knockdown of AfrDsxM in male larvae led to the appearance of female traits including an ovary-like structure in the original male reproductive system and an elevated expression of vitellogenin. However, silencing of AfrDsxF induced no clear phenotypic change in female Artemia. These results indicated that the male AfrDSXM may act as inhibiting regulator upon the default female developmental mode in Artemia. Furthermore, electrophoretic mobility shift assay analyses revealed that the unique DM domain of AfrDSXs can specifically bind to promoter segments of potential downstream target genes like AfrVtg. These data show that AfrDSXs play crucial roles in regulating sexual development in Artemia, and further provide insight into the evolution of sex determination/differentiation in sexual organisms.
Asunto(s)
Artemia , Isoformas de ARN , Animales , Masculino , Femenino , Artemia/genética , Isoformas de ARN/metabolismo , Empalme Alternativo , Isoformas de Proteínas/genética , Isoformas de Proteínas/metabolismo , Diferenciación Sexual/genéticaRESUMEN
Online weight-loss communities (OWCs) have become increasingly popular for weight management; they enable individuals to monitor (i.e. self-monitoring) and discuss (i.e. social interaction) their weight-loss experiences. This study investigates the relationship between prior weight-loss experiences (success and failure), online social support, and subsequent weight-loss outcome in the context of OWCs and based on self-determination theory. We collected the data of 1465 users from one popular OWC and deployed two logit regression models to estimate the effects of prior weight-loss experiences on subsequent weight-loss success as well as the moderating role of social support. The results revealed that prior successful weight-loss experiences were positively related to subsequent weight-loss outcome, while the relationship between prior failed weight-loss experiences and subsequent weight-loss outcome was negative. Meanwhile, online social support can not only be positively related to subsequent weight-loss outcome, but also buffer the negative role of prior failed weight-loss experiences. Nevertheless, social support had no significant moderating role in the relationship between prior successful weight-loss experiences and subsequent weight-loss outcome. This study contributes to the literature on prior experiences and online social support in the context of OWCs and provides valuable insights to improve participants' engagement and their weight-loss success.
Asunto(s)
Apoyo Social , Pérdida de Peso , Humanos , Modelos LogísticosRESUMEN
Nowadays, early defect detection plays a significant role for the railway safety warning. However, the existing methods cannot satisfy the requirements of real-time and high-precision detection. Here, a high-precision, distributed and on-line method for detecting rail defect is proposed and demonstrated. When a train goes through defects, the instantaneous elastic waves will be excited by the wheel-rail interaction, which will further propagate along railway tracks bidirectionally. Through mounting the backscattering enhanced optical fiber on the railway as sensors, the fiber optic distributed acoustic sensing system can record the propagation trace precisely. Further, the acoustic propagation fitting method is applied onto the propagation data to detect and locate defects along the long-distance railway. Especially, the dual-frequency joint-processing algorithm is proposed to improve the location accuracy. The field test proves that multiple defects along the railway can be successfully identified and located with a standard deviation of 0.314m. To the best of our knowledge, this work is the first report of distributed rail defect detection, which will bring a breakthrough for high-precision structural damage detection in the infrastructures such as the railway, pipeline and tunnel.
RESUMEN
In order to suppress the noise of the coherent fiber distributed acoustic sensing (DAS) system, the spatio-temporal joint oversampling-downsampling technique is proposed. The spatial oversampling is used for artificially dense sampling, whose spacing is far less than the target spatial resolution. Then the spatial downsampling performed by the average of multiple differential sub-vectors is utilized to reduce the influence of noise vectors, which could completely eliminate the interfere fading without increasing any system complexity and introducing any crosstalk. Meanwhile, the temporal oversampling-downsampling is analyzed from the perspective of theory and simulation, demonstrating that the noise floor will decrease with the increase of downsampling coefficient. The temporal oversampling is carried out to expand the noise distribution bandwidth and ensure the correct quantization of the noise frequency. Then the temporal downsampling of differential phase reconstruction is utilized to recover the target bandwidth and reduce the out-of-band noise. The experimental results prove that the noise floor is inversely correlated with the spatiotemporal downsampling factors. The strain resolution of the DAS system with the proposed scheme can reach 2.58pε/âHz@100Hz-500Hz and 9.47pε/âHz@10Hz under the condition of DC-500Hz target bandwidth, as well as the probability of the large-noise sensing channels is greatly reduced from 44.32% to 0%. Moreover, the demodulated SNR of dynamic signal is improved by 20.8dB compared with the traditional method. Without any crosstalk, the noise floor is optimized 8dB lower than the averaging technique. Based on the proposed method, the high-performance DAS system has significant competitiveness in the applications with the demand of high-precision and high-sensitivity, such as passive-source seismic imaging and VSP exploration.
RESUMEN
A wavelength-tunable noise-like pulse (NLP) erbium-doped fiber laser incorporating PbS quantum dot (QD) polystyrene (PS) composite film as a saturable absorber (SA) is experimentally demonstrated. The wavelength tuning is implemented via a Lyot filter consisting of a segment of polarization-maintaining fiber (PMF) and a 45° tilted fiber grating. By adjusting the polarization state of the ring cavity, the laser can deliver NLP with a continuous wavelength-tunable range from 1550.21 to 1560.64 nm. During continuous wavelength tuning, the output power varies between a range of 30.88-48.8 mW. Worthwhile noting is that the output power of 48.8 mW is the reported highest output power for wavelength-tunable NLP operation in an erbium-doped fiber laser using composite film as a saturable absorber.
RESUMEN
We have numerically and experimentally presented the diffraction characteristics of radiated tilted fiber grating (RTFG) in terms of the spectrum, bandwidth, degree of polarization, angular dispersion, and temperature crosstalk. The theoretical and experimental results have shown that the polarization property, bandwidth, and dispersion of RTFG highly depended on the tilt angle of RTFG, and the RTFG has ultra-low temperature crosstalk. We have simulated the transmission spectrum of the RTFG with different tilt angles (25°, 31°, 38°, 45°, and 54°), in which the results show that the larger tilt angle has the wider bandwidth. The RTFGs with the tilt angle of 25°, 31°, 38°, 45°, and 54° have the 3dB bandwidth of 110 nm, 144 nm, 182 nm, 242 nm, and 301 nm, respectively. Besides, the degree of polarization (DOP) of the radiated light from RTFG with the different tilt angles are 0.876, 0.944, 0.967, 0.998, and 0.970, respectively, and the RTFG has the maximum DOP at the tilt angle of 45°, which could be used as single-polarization diffraction device. The experimental results show that with further increase or decrease of the tilt angle, the DOP of radiated light of RTFG would decrease. Both the theoretical and experimental results show that the smaller tilt angle could greatly improve the diffraction angular dispersion of RTFG, in which the 25°, 31°, 38°, and 45° RTFG have the angular dispersion of 0.2288 °/nm, 0.1026 °/nm, 0.0714 °/nm, and 0.0528 °/nm, respectively. Due to the broad working bandwidth, the diffraction angles of RTFG have ultra-low temperature crosstalk, where -0.00042, -0.00054, -0.00064, and -0.00099 degree / °C at the tilt angle of 25°, 31°, 38°, and 45°. Finally, we have demonstrated a miniaturized spectrometer integrated by a 25° RTFG, which has a high spectral resolution of 0.08 nm. The proposed RTFG would be an ideal in-fiber diffraction device and widely applied in spectral analysis, space optical communication, and Lidar areas.
RESUMEN
In this Letter, we have proposed an in-fiber duplex optical antenna based on a 45° radiated titled fiber grating (RTFG), in which the 45° RTFG not only radiates the light from the fiber core to the free space, but also harvests the light from the free space back into the fiber core. Using the finite difference time domain method, we have theoretically analyzed the light recoupling efficiency of the RTFG. The simulated results have shown that the RTFG-based optical antennas have a maximum coupling efficiency of 10%. The recoupling wavelength and efficiency are related to the grating period and horizontal incidence angle. Furthermore, we demonstrate a programmable spectral filtering system based on the 45° RTFG antennas, which could achieve filtering with arbitrary spectral shapes. The spectral resolution is 0.4â nm and the insertion loss is around 20â dB. The proposed programmable spectral filtering system has a compact structure compared with the traditional filter.