RESUMEN
Quasi-two-dimensional (quasi-2D) layered perovskites with mixed dimensions offer a promising avenue for stable and efficient solar cells. However, randomly distributed three-dimensional (3D) perovskites near the film surface limit the device performance of quasi-2D perovskites due to increased nonradiative recombination and ion migration. Herein, we construct a 2D (n = 4 top)-3D-2D (n = 2 bottom) heterostructure of quasi-2D perovskites by using 3-chlorobenzylamine iodine, which can effectively reduce defect density and restrain ion migration. A champion efficiency of 22.22% for quasi-2D perovskite solar cells is achieved due to remarkably reduced nonradiative voltage loss and increased electron extraction. Additionally, the 2D-3D-2D perovskite solar cells also exhibit excellent thermal and humidity stabilities, retaining over 90 and 85% of the initial efficiencies after 2000 h under a heat stress of 65 °C and at air ambient of â¼50% humidity, respectively. Our results provide a general approach to tune perovskite films for suppressing ion migration and achieving high-performance perovskite solar cells.
RESUMEN
Variation in the condition of marine sediments provides selective preservation milieus, which act as a key determinant for the abundance and distribution of dinoflagellate resting cysts in natural sediments. Microbial degradation is an understudied biological factor of potential importance in the processes. However, gaps remain in our knowledge about the fundamental information of the bacterial consortia associated with dinoflagellate resting cysts both in laboratory cultures and in the field. Here we used Scrippsiella acuminata as a representative of cyst-producing dinoflagellates to delineate the diversity and composition of bacterial microbiomes co-existing with the laboratory-cultured resting cysts, and to explore possible impacts of low temperature, darkness, and anoxia (the mock conditions commonly observed in marine sediments) on the associated bacterial consortia. Bacterial microbiome with high diversity were revealed associated with S. acuminata at resting stage. The mock conditions could significantly shift bacterial community structure and exert notably inhibitory effects on growth-promoting bacteria. Resting cysts under conditions typically observed in marine sediments fostered bacterial microbiomes with more diverse trophic strategies, characteristic of prominently enriched anaerobic chemotrophic bacteria generating energy via respiration with several different terminal electron acceptors, which yielded more acidic milieu unfavorable for the preservation of calcareous resting cysts. Our findings suggest that there is complex and dynamic interaction between dinoflagellates resting cysts and the associated bacterial consortia in natural sediments. This intrinsic interaction may influence the maintenance and/or accumulation of dinoflagellate resting cysts with potential of germination and initiation blooms in the field.
RESUMEN
In the wake of the COVID-19 pandemic, respiratory tract infections have emerged as a significant global threat, yet their impact on public health was previously underappreciated. This study investigated the antiviral efficacy of the nano-coating agent BARRIER90, composed of silicon-quaternary ammonium compound and a naturally derived biopolymer, against three distinct respiratory viruses: Influenza A (H1N1), Adenovirus Type 1, and Enterovirus-Coxsackie B1. BARRIER90 exhibited robust and sustained virucidal activity, persisting up to 90 days post-coating, against the enveloped virus, Influenza A, with significant reduction in viral plaques. Contrastingly, its efficacy against non-enveloped viruses revealed transient activity against Enterovirus-Coxsackie B1, with almost no antiviral activity observed against Adenovirus Type 1. These findings indicate the potential of antimicrobial coatings in mitigating viral transmission through contaminated surfaces (fomites), which harbour pathogenic viruses for longer periods. Antimicrobial coatings may facilitate infection control in various settings, including healthcare facilities and shared workspaces.
RESUMEN
Microplastics (MPs) are widespread in agroecosystems and profoundly impact soil microbiome and nutrient cycling. However, the effects of MPs on soil autotrophic ammonium oxidization processes, including nitrification, complete ammonium oxidation (comammox), anaerobic ammonium oxidation (anammox), and anaerobic ammonium oxidation coupled to iron reduction (Feammox), remain unclear. These processes are the rate-limiting steps of nitrogen cycling in agroecosystems. Here, our work unveiled that exposures of polyethylene (PE), polypropylene (PP), polylactic acid (PLA), and polybutylene adipate terephthalate (PBAT) MPs significantly modulated ammonium oxidization pathways with distinct type- and dose-dependent effects. Nitrification remained the main contributor (56.4-70.7 %) to soil ammonium removal, followed by comammox (11.7-25.6 %), anammox (5.0-20.2 %) and Feammox (3.3-11.6 %). Compared with conventional nonbiodegradable MPs (i.e., PE and PP), biodegradable MPs (i.e., PLA and PBAT) exhibited more pronounced impacts on soil nutrient conditions and functional microbes, which collectively induced alterations in soil ammonium oxidation. Interestingly, low-dose PLA and PBAT remarkably enhanced the roles of anammox and Feammox in soil ammonium removal, contributing to the mitigation of soil acidification in agroecosystems. This study highlights the diverse responses of ammonium oxidization pathways to MPs, further deepening our understanding of how MPs affect biogeochemical cycling and enriching strategies for agricultural managements amid increasing MPs pollution.
RESUMEN
Nitrogen, phosphorus and potassium are essential for crop growth, which are abundant in urine. Although numerous studies have developed techniques to recover ammonium and phosphorus from urine, limited research made efforts on the recovery of potassium, which is a non-renewable resource with uneven global distribution. In this study, we explored the possibility of zeolite based mixed matrix membranes (MMMs) to selectively recover ammonium and potassium from urine, with minimal detention of sodium. The findings demonstrated that upon the pre-treatment of zeolites with sodium chloride solution, a 70 wt% zeolite loaded MMM could achieve 69.3 % recovery of potassium and almost full recovery of ammonium. By varying the desorption temperatures and MMMs production process, it was discovered that stepwise backwash at low temperature (276 K) greatly lowered sodium recovery whilst simultaneously enhancing the recovery of potassium and ammonium. This study demonstrates the potential of recovering potassium and ammonium from urine using zeolite-loaded MMMs, coupled with achieving low-sodium recovery.
RESUMEN
Didecyldimethylammonium chloride (DDAC), a toxic quaternary ammonium compound (QAC) linked to multidrug resistance, is used widely in households and hospitals and on swine farms to prevent disease transmission. However, little is known about its occurrence in watersheds receiving livestock wastewaters or manure. We monitored DDAC and tracers (veterinary and human drugs) once a season over a year at 14 sites in a Japanese watershed where swine outnumbered humans 1.2 to 1 and where both swine and human wastewaters were largely treated on site. DDAC concentrations in sewage-treatment-plant effluent (33-52 ng/L) were close to, whereas those in river waters (3.6-16,672 ng/L) far exceeded, those reported worldwide. DDAC mass flows at the catchment outlet (1692-3816 µg/s) were higher than those of any of the drugs. DDAC concentrations were significantly correlated with total concentrations of veterinary drugs (Spearman's correlation coefficient, 0.95, P < 0.01), indicating that the major pathway of DDAC entry to surface waters was via effluent discharge from swine farms. Comparison of observed and predicted mass flows implied that a substantial percentage of DDAC was washed from the barn floor into swine excrement. To our knowledge, this is the first study to demonstrate QAC hotspots attributable to animal husbandry.
RESUMEN
Anammox is recognized as a prospective alternative for future biological nitrogen removal technologies. However, the nitrate by-products produced by anammox bacteria limit its overall nitrogen removal efficiency below 88 %. This study introduced Fe(III) into the anammox bioreactor to enhance the nitrogen removal efficiency to approximately 95 %, surpassing the biochemical limit of 88 % imposed by anammox stoichiometry. Anammox sludge was demonstrated to utilize extracellular polymeric substances to reduce Fe(III) into Fe(II), and this process promoted the dominance of Ca. Brocadia. The iron addition improved the abundance of narGHI genes and facilitated the partial dissimilatory nitrate reduction to ammonium, with nitrite as the end product. The accumulated nitrite was then eliminated through the anammox pathway, along with the excess ammonium (30 mg/L) in the influent. Overall, this study deepens our understanding of the enhanced nitrogen removal triggered by Fe(III) in anammox sludge and offers an effective approach to boost anammox process.
RESUMEN
Quaternary ammonium salt bactericides are broad-spectrum bactericides often used in oral care products because of their high antibacterial efficacy, strong penetration, and low toxicity. However, the excessive use of quaternary ammonium salt bactericides may cause contact dermatitis, scalding poisoning, and even death. Existing methods to determine quaternary ammonium salt bactericides are unable to meet current requirements owing to the lack of determination components. Therefore, establishing a simple and accurate method for the simultaneous detection of more quaternary ammonium salt bactericides is necessary. In this study, a method that couples sample pretreatment with high performance liquid chromatography-evaporative light-scattering detection (HPLC-ELSD) was developed for the simultaneous determination of quaternary ammonium salt bactericides in oral care products, including dodecyltrimethylammonium chloride, dodecyldimethylbenzylammonium chloride, benzethonium chloride, tetradecyl trimethyl ammonium chloride, tetradecyldimethylbenzylammonium chloride, N-hexadecyltrimethylammonium chloride, benzyldimethylhexadecylammonium chloride, trimethylstearylammonium chloride, stearyldimethylbenzylammonium chloride, and docosyltrimethylammonium chloride. Some of these bactericides do not absorb ultraviolet light, so a universal evaporative light-scattering detector was used owing to testing cost and stability concerns. The paste samples contained thickening agents, which are highly soluble in water but insoluble in organic solvents; these agents can seriously affect the results of sample pretreatment and damage the chromatographic column. Hence, sample dehydration was necessary. In this study, four dehydration methods were compared. Anhydrous sodium sulfate (Na2SO4) was selected, and the amount of Na2SO4 was optimized. Based on the solubility of the 10 target compounds and extraction efficiency, three extraction solvents were compared, and ethanol was selected. Ultrasonic extraction was the primary extraction process used in this study. The effects of different ultrasonication times, temperatures, and powers on the extraction recoveries were also investigated. Ultimately, the optimized conditions were as follows: extraction of the dehydrated paste and powder samples using ethanol at room temperature (25 â) for 20 min under 100 W ultrasound power, and dilution of the liquid sample with ethanol. After extraction, the samples were separated on an Acclaim Surfactant column (150 mm×4.6 mm, 5 µm) with 50 mmol/L ammonium acetate aqueous solution (pH=5.5) (A) and acetonitrile (B) as mobile phases. The gradient elution program were as follows: 0-5.0 min, 75%A-35%A, 5.0-15.0 min, 35%A-20%A, 15.0-20.0 min, 20%A, 20.0-21.0 min, 20%A-75%A, 21.0-25.0 min, 75%A. An external standard method was used for quantitative determination. The 10 compounds were analyzed within 25 min. Linear equations, correlation coefficients, and linear ranges were obtained by analyzing a series of mixed standard working solutions. The limits of detection (LODs, S/N=3) and quantification (LOQs, S/N=10) of the 10 components were determined. Stearyldimethylbenzylammonium chloride and docosyltrimethylammonium chloride showed good linear relationships in the range of 10-200 mg/L, while the other compounds demonstrated good linear relationships in the range of 5-100 mg/L. In all cases, correlation coefficients (R2) of no less than 0.9992 were obtained. The LODs and LOQs were in the range of 1.42-3.31 mg/L and 4.25-9.94 mg/L, respectively. Ten analytes were spiked in blank matrices, such as toothpaste (paste), mouthwash (liquid), and dentifrice powder (powder) at three levels, and the recoveries and precisions were calculated. The average recoveries were 87.9%-103.1%, and the corresponding relative standard deviations (RSDs) did not exceed 5.5% (n=6). The developed method was used to detect 109 oral care products. Benzyldimethylhexadecylammonium chloride and stearyldimethylbenzylammonium chloride revealed high detection rates. Moreover, the amount of stearyldimethylbenzylammonium chloride in one toothpaste sample exceeded regulatory requirements. Given its advantages of good precision and accuracy, the developed method is suitable for the quantitative analysis of the 10 aforementioned compounds in typical oral care products. The study findings can serve as a reference for the quality and safety monitoring of oral care products.
Asunto(s)
Compuestos de Amonio Cuaternario , Compuestos de Amonio Cuaternario/química , Compuestos de Amonio Cuaternario/análisis , Cromatografía Líquida de Alta Presión , Antibacterianos/análisis , Luz , Dispersión de RadiaciónRESUMEN
Quaternary ammonium compounds (QACs) are widely detected in the aquatic environment due to their extensive use in a wide array of antibacterial products during the pandemic. In the current study, UV/monochloramine (UV/NH2Cl) was used to degrade three typical QACs, namely benzalkonium compounds (BACs), dialkyl dimethyl ammonium compounds (DADMACs), and alkyl trimethyl ammonium compounds (ATMACs). This process achieved high efficiency in removing BACs from water samples. The transformation products of QACs treated with UV/NH2Cl were identified and characterized using a high-resolution mass spectrometer, and transformation pathways were proposed. The formation of N-nitroso-N-methyl-N-alkylamines (NMAs) and N-nitrosodimethylamine (NDMA) were observed during QAC degradation. The molar formation yield of NDMA from C12-BAC was 0.04 %, while yields of NMAs reached 1.05 %. The ecotoxicity of NMAs derived from QACs was predicted using ECOSAR software. The increased toxicity could be attributed to the formation of NMAs with longer alkyl chains; these NMAs, exhibited a one order of magnitude increase in toxicity compared to their parent QACs. This study provides evidence that QACs are the specific and significant precursors of NMAs. Greater attention should be given to NMA formation and its potential threat to the ecosystem, including humans.
RESUMEN
Manganese(IV) (Mn(IV)) reduction coupled to anaerobic ammonium (NH4+-N) oxidation (Mnammox) is a recently identified metal oxide-mediated nitrogen (N) loss pathway, holding potential value for the efficient removal of NH4+-N from wastewater. However, little is known about the application of Mnammox in wastewater treatment. Here, a novel Mnammox bacterium Aromatoleum evansii (strain MAY27) was screened. Strain MAY27 can utilize MnO2 as an electron acceptor to achieve NH4+-N removal under a low C/N condition (C/N = 0.5). The influencing factors in the Mnammox process and the Mn(IV) reduction driving effect on NH4+-N oxidation were investigated. The physiological characteristics of strain MAY27 and differential metabolic pathways were identified through whole-genome sequencing and metabolomic analyses. A significant up-regulation of several key pathways upon the addition of MnO2, including glycolysis/gluconeogenesis, transmembrane transporter activity, and oxidoreductase activity. This study contributes to the advancement of biotechnological approaches for treating N-containing wastewater.
RESUMEN
Ammonium polyphosphate (APP) and self-made nickel phytate (PANi) were used as modified materials to prepare green biomass rigid polyurethane foam (RPUF). The flame retardancy, thermal stability, smoke toxicity and mechanical properties of the modified RPUF were investigated by limiting oxygen index (LOI), a cone calorimetry (CONE) test, thermogravimetric analysis and a compression test. The results showed that the RPUF with 10 wt% APP (PANi/APP10) had the highest LOI of 26.5%. Its peak heat release rate (PHRR) and total heat release (THR) were reduced by 29.64% and 24.05% compared with PANi/APP0 without APP. And its smoke production rate (SPR) and total smoke release (TSR) decreased by 33.14% and 19.88%, respectively. Compared with pure RPUF, the compressive strength of PANi/APP10 was increased by 50%, mainly because APP itself was an ultra-fine powder, which was better compatible with the matrix and improved the hardness of the material. The results showed that the synergistic effect of the gas phase and the condensed phase mechanism could effectively improve the flame-retardant effect. The current research results provided a new strategy for the preparation of green and low-toxicity RPUF.
RESUMEN
An innovative circular economy (CE) system was implemented at the wastewater treatment plant (WWTP) in Brunswick. The performance of the CE system was evaluated for 4 years: the thermal pressure hydrolysis enhanced the methane production by 18% and increased the digestate dewaterability by 14%. Refractory COD formed in thermal hydrolysis and increased the COD concentration in the WWTP effluent by 4 mg L-1 while still complying with the legal threshold. Struvite production reached high phosphorus recovery rates of >80% with a Mg:P molar ratio ≥0.8. Nitrogen was successfully recovered as ammonium sulfate with high recovery rates of 85-97%. The chemical analyses of secondary fertilizers showed a low pollutant content, posing low risks to soil and groundwater ecosystems. The total carbon footprint of the WWTP decreased due to enhanced biogas production, the recovery of renewable fertilizers and a further reduction of nitrous oxide emissions. Using green energy will be crucial to reach carbon neutrality for the entire WWTP.
Asunto(s)
Biocombustibles , Aguas del Alcantarillado , Aguas del Alcantarillado/química , Carbono/química , Alemania , Eliminación de Residuos Líquidos/métodos , Fertilizantes , Aguas Residuales/química , Fósforo/química , Nitrógeno/químicaRESUMEN
East African lakes, especially soda lakes, are home habitats for massive numbers of wildlife such as flamingos, mammals, and fishes. These lakes are known for their high primary production due to local high temperatures, light intensities, and alkalinity (inorganic carbon). However, these lakes, normally within remote areas, receive low nutrient inputs. Ammonium (NH4+) recycling and/or nitrogen fixation can become the major N supply mechanisms for phytoplankton. However, the driving forces on microbial N nutrition in lakes with minimal anthropogenic disturbance remain poorly understood. Using stable isotope tracer techniques, NH4+ recycling rates were measured in 18 lakes and reservoirs in East Africa (Tanzania and Kenya) during the dry season in early 2020. Three functional genes (nifH, gdh, and ureC) relating to microbial N nutrition were also measured. The regeneration of NH4+ supported up to 71 % of the NH4+ uptake. Positive community biological NH4+ demands (CBAD) for all lakes and reservoirs indicate an obvious N demand from microbial community. Our study provides clear evidence that microbial NH4+ uptake rates linked closely to the dissolved organic matter (DOM) properties (e.g., the absorption coefficient at 254 nm, percents of total fluorescence intensity contributed by microbial humic-like and protein-like components) and that water residence time drives microbial NH4+ recycling by regulating the duration of in-lake DOM processing and influencing algal growth. Phytoplankton, especially those of Cyanophyceae, showed maximum biomass and higher NH4+ recycling rates at a certain range of water residence time (e.g., 5-8 years). However, CBAD showed a decreasing trend with longer water residence time, which may be influenced by changes in the algal community composition (e.g., % Cyanophyceae vs. % Bacillariophyceae). These results indicate that DOM dynamics and the water residence time have the potential to facilitate the understanding of microbial nitrogen supply status in East African lakes.
RESUMEN
The optimization of hydrogel structure is crucial for adsorption capacity, mechanical stability, and reusability. Herein, a chitosan and laponite-XLS co-doped poly(acrylic acid-co-acrylamide) hydrogel (CXAA) with honeycomb-like porous structures is synthesized by cooperative cross-linking of 2-hydroxypropyltrimethyl ammonium chloride chitosan (HACC) and laponite-XLS in reticular frameworks of acrylic acid (AAc) and acrylamide (AM). The CXAA exhibits extraordinary mechanical performances including tough tensile strength (3.36 MPa) and elasticity (2756 %), which facilitates recycling in practical adsorption treatment and broadens potential applications. Since the regular porous structures can fully expose numerous adsorption sites and electronegative natures within polymer materials, CXAA displays efficient and selective adsorption properties for cationic dyes like methylene blue (MB) and malachite green (MG) from mixed pollutants and can reach record-high values (MB = 6886 mg g-1, MG = 11,381 mg g-1) compared with previously reported adsorbents. Therefore, CXAA exhibits promising potential for separating cationic and anionic dyes by their charge disparities. Mechanism studies show that the synergistic effects of HACC, laponite-XLS, and functional groups in monomers promote highly efficient adsorption. Besides, the adsorption capacity of CXAA remains stable even after undergoing five cycles of regeneration. The results confirm that CXAA is a promising adsorbent for effectively removing organic dyes in wastewater.
RESUMEN
Here, we present the electrochemical determination of ammonium in water samples, emphasizing the importance of accurate and precise assessment of its concentration. The modified electrode used in this study was fabricated through the anodic polymerization of 1-aminoanthraquinone (1-AAQ) and deposition of silver particles into a carbon paste electrode. The fabrication process involved cyclic voltammetry in a 0.1 M HCl solution, followed by the application of a potential of 0.2 V for 75 s. The resulting Ag/poly-1-AAQ/CPE exhibited remarkable electrochemical properties, as confirmed by scanning electron spectroscopy (SEM), energy-dispersive X-ray analysis (EDX), and elemental mapping. The successful deposition of silver at percentages of 12.07% on Ag/CPE and 0.75% on Ag/poly-1-AAQ/CPE was observed. The Ag/poly-1-AAQ/CPE was employed for impedimetric determination of ammonium in a solution of 0.1 M Na2SO4. The charge transfer resistance) output from the fitting of the experimental impedimetric data of ammonium determination exhibited good linearity over a concentration range of 5 µM to 200 µM NH4+, with a detection limit of 3.3 µM NH4+. The precision of the modified electrode over ten replicate measurements were conducted at three concentration levels (a low of 5 µM NH4+, a medium of 50 µM NH4+, and a high of 200 µM NH4+). The obtained relative standard deviation (RSD) values of 18%, 12% and 7%, respectively, indicating good precision.
RESUMEN
Due to their excellent properties, antimicrobial fiber membranes are widely applied in bioprotective materials. This work addresses the preparation of thermoplastic polyurethane (TPU)-based fiber membranes with active antimicrobial properties. 2-hydroxypropyl trimethyl ammonium chloride-terminated hyperbranched polymer (HBP-HTC) was synthesized and used as an antimicrobial agent. The fiber membranes were obtained by electrospinning a mixed solution of HBP-HTC and TPU. Different electrospinning conditions were investigated, such as the spinning voltage and drum rotation speed. The fiber membrane prepared under a 22 kV anode voltage and 100 rpm rotation speed had an average fiber diameter of 1.66 µm with a concentrated diameter distribution. Antibacterial tests showed that when the fiber membrane was loaded with 1500 mg/kg of HBP-HTC, the antibacterial rates of E. coli as well as S. aureus both reached 99.99%, exhibiting excellent proactive antimicrobial performance. Moreover, the protective performance of the fiber membrane was outstanding, with a filtration efficiency of 99.9%, a hydrostatic pressure resistance greater than 16,758 Pa, and a moisture permeability of 2711.0 gâ (m2â d)-1.
RESUMEN
In this study, facile construction engineering of Pr6O11@C with efficient photocatalytic activity was established. Taking advantage of the flocculation of Pr3+ in the base medium, acid red 14 (AR14) was flocculated together with Pr(OH)3 precipitate, in which Pr(OH)3 and AR14 mixed highly uniformly. Calcinated at high temperature in N2, a novel Pr6O11@C was successfully synthesized. The resulting materials were characterized by XRD, SEM, FT-IR, Raman, and XPS techniques. The results show that the cubic Pr6O11@C with Fm3m space group, similar to that of Pr6O11, was obtained. From the results of the photodegradation of AR14, it is found that the photocatalytic efficiency of Pr6O11@C is higher than that of pure Pr6O11 due to the formation of abundant carbon bonds and oxygen vacancies. Compared with pure Pr6O11 and other carbon-based composites, the acid resistance of Pr6O11@C is greatly improved due to the highly uniform dispersion of Pr6O11 and C, which lays a solid foundation for the practical application of Pr6O11@C. Moreover, the role of NH3·H2O and NaOH used as precipitants for the photocatalytic efficiency of Pr6O11 was investigated in detail.
RESUMEN
In ion chromatography studies, the matrix effect of other inorganic ions present in the sample is a well-known phenomenon. In this work, the behavior of inorganic and organic ions was studied in a system overloaded with ammonium ions. The ammonium ions came from a solution of ammonium hydroxide in various concentrations (0.25-1.25%). In this system, which was significantly overloaded with ammonium ions, the behavior of three ions were tested (lithium, tris, and sodium cations). The measurements were performed at different eluent concentrations (6-17 mM), chromatographic column temperatures (25-40 °C), and injected volumes (15-40 µL). The retention times of sodium and lithium ions increased with increasing amounts of injected ammonium, while tris remained essentially unchanged, indicating that the resolution of these ions can be influenced by varying the concentration of the matrix. The results suggested that the observed effect was due to a combination of the pH change caused by the injected matrix, the dissociation of tris ions, the dissociation of the carbocylic ion-exchange groups of stationary phase, the change in buffer capacity, and the amount of ammonium ion introduced. It has been shown that in a well-designed experiment, the addition of ammonium hydroxide to the sample at concentrations greater than 1% can improve the efficiency of organic and inorganic cation separation. It was found that 8 mM methanesulfonic acid eluent, 30 °C, 1% ammonium hydroxide matrix concentration, and 25 µL injection were optimal for the baseline separation of tris and sodium ions on the high-capacity Dionex CS16 column. These ions could not be separated on this column without the presence of the ammonium matrix.
RESUMEN
Perchlorate (ClO4-) mainly exists in the form of ammonium perchlorate in industrial production. However, the degradation mechanisms of different concentrations of ammonium nitrogen (NH4+-N) and ClO4- mixed pollutants in the environment are not well understood. This study aims to explore the potential of different types of carbon sources for ClO4- and NH4+-N biodegradation. Experimental results showed that the concentration and type of carbon sources are decisive to simultaneous removal of NH4+-N and ClO4-. Under condition of C(COD)/C(ClO4-) ratio of 21.15 ± 4.40, the simultaneously removal efficiency of ClO4- and NH4+-N in acetate (Ace) was relatively higher than that in methanol (Met). C(NH4+-N)/C(ClO4-) ratio of 9.66 ± 0.51 and C(COD)/C(ClO4-) ratio of 2.51 ± 0.87 promoted ClO4- reduction in glucose-C (Glu-C). However, high concentration of Glu could cause pH decrease (from 7.57 to 4.59), thereby inhibiting ClO4- reduction. High-throughput sequencing results indicated that Proteobacteria and Bacteroidetes have made a major contribution to the simultaneous removal of NH4+-N and ClO4-. They are two representative bacterial phyla for participating in both ClO4- reduction and denitrification. Notably, the abundance of main ClO4- degrading bacteria (such as Proteobacteria, Chloroflexi, and Firmicutes) significantly increased by 528.57 % in Glu-C. It can be inferred that the concentration of carbon source and NH4+-N were the most important factors determining the removal efficiency of ClO4- by influencing changes in the core microbial community. This study will provide new techniques and mechanistic insights for the simultaneous removal of mixed ClO4- and nitrogen pollutants, which can also provide theoretical support for innovation in future biological treatment processes.
RESUMEN
Miniaturization and mass-production of potentiometric sensor systems is paving the way towards distributed environmental sensing, on-body measurements and industrial process monitoring. Inkjet printing is gaining popularity as a highly adaptable and scalable production technique. Presented here is a scalable and low-cost route for flexible solid-contact ammonium ion-selective electrode fabrication by inkjet printing. Utilization of inkjet-printed melamine-intercalated graphene nanosheets as the solid-contact material significantly improved charge transport, while evading the detrimental water-layer formation. External polarization was investigated as a means of improving the inter-electrode reproducibility: the standard deviations of E0 values were reduced after electrode polarization, the linear region of the response was extended to the range 10-1-10-6 M of NH4Cl and LODs reduced to 0.88 ± 0.17 µM. Finally, we have shown that the electrodes are adequate for measurements in a complex real sample: ammonium concentration was determined in landfill leachate water, with less than 4 % deviation from the reference method.