Thermo-responsible PNIPAM-grafted polystyrene microspheres for mesenchymal stem cells culture and detachment.

The preparation of cells is a critical step in cell therapy. To ensure the effectiveness of cells used for clinical treatments, it is essential to harvest adherent cells from the culture media in a way that preserves their high viability and full functionality. In this study, we developed temperature-responsive PNIPAM-grafted polystyrene microspheres using reversible addition-fragmentation chain transfer polymerization. These microspheres allow for the non-destructive harvesting of cultured cells through temperature changes. The composition and physicochemical properties of the PNIPAM-grafted polystyrene microspheres were confirmed using infrared spectroscopy, elemental analysis, dynamic light scattering, and thermogravimetric analysis. In vitro experiments demonstrated that these microspheres exhibit excellent biocompatibility, supporting the adhesion and proliferation of various cells. Moreover, the microspheres showed good temperature responsiveness in thermosensitive detachment experiments with GFP-HepG2 cells and umbilical cord mesenchymal stem cells (UC-MSCs). Additionally, through orthogonal experiments, we identified a cell detachment aid mixture that significantly improved the dispersibility of cells detached from the microspheres, enhancing the efficiency of thermosensitive cell detachment by approximately 40%. The harvested UC-MSCs retained their capacity for re-proliferation and trilineage differentiation. Consequently, the temperature-responsive microspheres developed in this study, combined with the cell detachment aid mixtures, hold great potential for large-scale culture and harvesting of therapeutic cells in clinical applications.

Triboelectric Nanogenerators Based on Transition Metal Carbo-Chalcogenide (Nb2S2C and Ta2S2C) for Energy Harvesting and Self-Powered Sensing.

With burgeoning considerations over energy issues and carbon emissions, energy harvesting devices such as triboelectric nanogenerators (TENGs) are developed to provide renewable and sustainable power. Enhancing electric output and other properties of TENGs during operation is the focus of research. Herein, two species (Nb2S2C and Ta2S2C) of a new family of 2D materials, Transition Metal Carbo-Chalcogenides (TMCCs), are first employed to develop TENGs with doping into Polydimethylsiloxane (PDMS). Compared with control samples, these two TMCC-based TENGs exhibit higher electric properties owing to the enhanced permittivity of PDMS composite, and the best performance is achieved at a concentration of 3 wt. ‰ with open circuit voltage (Voc) of 112 V, short circuit current (Isc) of 8.6 µA and charge transfer (Qsc) of 175 nC for Nb2S2C based TENG, and Voc of 127 V, Isc of 9.6 µA, and Qsc of 230 nC for Ta2S2C based TENGs. These two TENGs show a maximum power density of 1360 and 911 mW m-2 respectively. Moreover, the tribology performance is also evaluated with the same materials, revealing that the Ta2S2C/PDMS composite as the electronegative material presented a lower coefficient of friction (COF) than the Nb2S2C/PDMS composite. Their applications for energy harvesting and self-powered sensing are also demonstrated.

Early Experiences of Serbian Surgeons Using No-Touch Technique for Vein Conduits in CABG Patients: A Follow-Up Study with Multi-Slice CT Angiography.

Background and Objectives: The saphenous vein graft (SVG) remains the most frequently used conduit worldwide, despite its common disadvantage of early graft failure. To solve the problem and reduce the SVG damage, Souza implemented a new technique where a vein is harvested with surrounding fascia and fat tissue (the so-called no-touch technique). Materials and Methods. A prospective study conducted from February 2019 to June 2024 included 23 patients who underwent myocardial revascularization using a no-touch vein, with follow-up control examinations using computed tomographic angiography to detect graft stenosis or occlusion. Results. Of the entire patient group, 17 (73.9%) were male, with a mean age of 67.39 ± 7.71 years. The mean follow-up period was 25 months. There were no major adverse cardiovascular or cerebrovascular events (MACCEs) during hospitalization, although one patient died in the hospital. Another patient died due to malignancy, but no MACCEs occurred during the follow-up period. According to multi-slice CT coronary angiography, the results were impeccable, with an astonishing 100% patency observed in all 20 IMA grafts and 58 no-touch SVGs examined. Conclusions. The excellent patency rate during the early follow-up period confirmed that the no-touch technique is a good option for surgical revascularization.

Interactions between volatile air pollutants and atmospheric water production - Effects of chemical properties, mechanisms, and transfer processes.

Regional water scarcity is among the most urgent challenges of global climate change. Atmospheric water harvesting is a promising method to mitigate these challenges, and the atmospheric water generator (AWG) is already an established technology. Although this method can produce over 10,000 L of water per day, the water's quality has not been studied in depth. Air pollutants, especially volatile organic compounds (VOCs), are potential contaminants of water produced from air. We evaluated the chemical and physical parameters of different VOCs that might influence their ability to be transferred from air to AWG water. Our findings strongly suggest that the ability to form hydrogen bonds is a key factor in this transfer. Henry's law constant, polarity, and intrinsic solubility were the main predictors of a VOC's transfer to AWG water. Hence, aliphatic or aromatic compounds (such as benzene or octane) were not found at significant concentrations in AWG water (e.g. above WHO guidelines), whereas ammonia and alcohol compounds were. This should be taken into consideration when analyzing potential contaminants in harvested atmospheric water. The condensation process itself was also found to enhance the transfer of VOCs into water droplets, and higher relative humidity (%RH) also increased VOC transfer. Gas-phase infrared spectrum analysis of VOCs at different %RH revealed possible interactions between water vapor and specific VOCs in the air. However, our main conclusion from this study is that VOC transfer from the air into AWG water occurs predominantly via dissolution in the condensed droplets, and strongly depends on their chemical properties of polarity and hydrogen-bond formation.

Quantification of biomass availability for wood harvesting and storage in the continental United States with a carbon cycle model.

BACKGROUND: Wood Harvesting and Storage (WHS) is a form of Biomass Carbon Removal and Storage (BiCRS) that utilizes a combined natural and engineered process to harvest woody biomass and put it into long term storage, most frequently in the form of subterranean burial. This paper aims to quantify the availability of woody biomass for the purposes of WHS in the continental United States using a carbon cycle modeling approach. Using a regional version of the VEGAS terrestrial carbon cycle model at 10 km resolution, this paper calculates the annual woody net primary production in the continental United States. It then applies a series of constraints to exclude woody biomass that is unavailable for WHS. These constraints include fine woody biomass, current land use, current wood utilization, land conservation, and topographical limitations. These results were then split into state by state and regional totals. RESULTS: In total, the model projects the continental United States could produce 1,274 MtCO2e (CO2 equivalent) worth of coarse woody biomass annually in a scenario with no anthropogenic land use or constraints. In a scenario with anthropogenic land use and constraints on wood availability, the model projects that 415 MtCO2e of coarse woody biomass is available for WHS annually. This is enough to offset 8.5% of the United States' 2020 greenhouse gas emissions. Of this potential, 20 MtCO2e is from the Pacific region, 77 MtCO2e is from the Western Interior, 91 MtCO2e is from the Northeast region, and 228 MtCO2e is from the Southeast region. CONCLUSION: There is enough coarse woody biomass available in the continental United States to make WHS a viable form of carbon removal and storage in the country. There is coarse woody biomass available across the continental United States. All four primary regions analyzed have enough coarse woody biomass available to justify investment in WHS projects.

Conceptual Piezoelectric-Based Energy Harvester from In Vivo Heartbeats' Cyclic Kinetic Motion for Leadless Intracardiac Pacemakers.

This paper studies the development of piezoelectric energy harvesting for self-powered leadless intracardiac pacemakers. The energy harvester fit inside the battery compartment, assuming that the energy harvester would replace the battery with a smaller rechargeable battery capacity. The power output analysis was derived from the three-dimensional finite element analysis and in vivo heart measurements. A Doppler laser at the anterior basal in the right ventricle directly measured the heart's kinetic motion. Piezoceramics in the cantilevered configuration were studied. The heart motion was periodic but not harmonic and shock-based. This study found that energy can be harvested by applying periodic bio-movements (cardiac motion). The results also showed that the energy harvester can generate 1.1 V voltage. The effect of various geometrical parameters on power generation was studied. This approach offers potential for self-powered implantable medical devices, with the harvested energy used to power devices such as pacemakers.

Enhanced Hybrid Nanogenerator Based on PVDF-HFP and PAN/BTO Coaxially Structured Electrospun Nanofiber.

Nanogenerators have garnered significant interest as environmentally friendly and potential energy-harvesting systems. Nanogenerators can be broadly classified into piezo-, tribo-, and hybrid nanogenerators. The hybrid nanogenerator used in this experiment is a nanogenerator that uses both piezo and tribo effects. These hybrid nanogenerators have the potential to be used in wearable electronics, health monitoring, IoT devices, and more. In addition, the versatility of the material application in electrospinning makes it an ideal complement to hybrid nanogenerators. However, despite their potential, several experimental variables, biocompatibility, and harvesting efficiency require improvement in the research field. In particular, maximizing the output voltage of the fibers is a significant challenge. Based on this premise, this study aims to characterize hybrid nanogenerators (HNGs) with varied structures and material combinations, with a focus on identifying HNGs that exhibit superior piezoelectric- and triboelectric-induced voltage. In this study, several HNGs based on coaxial structures were fabricated via electrospinning. PVDF-HFP and PAN, known for their remarkable electrospinning properties, were used as the primary materials. Six combinations of these two materials were fabricated and categorized into homo and hetero groups based on their composition. The output voltage of the hetero group surpassed that of the homo group, primarily because of the triboelectric-induced voltage. Specifically, the overall output voltage of the hetero group was higher. In addition, the combination group with the most favorable voltage characteristics combined PVDF-HFP@PAN(BTO) and PAN hollow, boasting an output voltage of approximately 3.5 V.

Statistics of the Sum of Double Random Variables and Their Applications in Performance Analysis and Optimization of Simultaneously Transmitting and Reflecting Reconfigurable Intelligent Surface-Assisted Non-Orthogonal Multi-Access Systems.

For the future of sixth-generation (6G) wireless communication, simultaneously transmitting and reflecting reconfigurable intelligent surface (STAR-RIS) technology is emerging as a promising solution to achieve lower power transmission and flawless coverage. To facilitate the performance analysis of RIS-assisted networks, the statistics of the sum of double random variables, i.e., the sum of the products of two random variables of the same distribution type, become vitally necessary. This paper applies the statistics of the sum of double random variables in the performance analysis of an integrated power beacon (PB) energy-harvesting (EH)-based NOMA-assisted STAR-RIS network to improve its outage probability (OP), ergodic rate, and average symbol error rate. Furthermore, the impact of imperfect successive interference cancellation (ipSIC) on system performance is also analyzed. The analysis provides the closed-form expressions of the OP and ergodic rate derived for both imperfect and perfect SIC (pSIC) cases. All analyses are supported by extensive simulation results, which help recommend optimized system parameters, including the time-switching factor, the number of reflecting elements, and the power allocation coefficients, to minimize the OP. Finally, the results demonstrate the superiority of the proposed framework compared to conventional NOMA and OMA systems.

Development of artificial photosystems based on designed proteins for mechanistic insights into photosynthesis.

This review aims to provide an overview of the progress in protein-based artificial photosystem design and their potential to uncover the underlying principles governing light-harvesting in photosynthesis. While significant advances have been made in this area, a gap persists in reviewing these advances. This review provides a perspective of the field, pinpointing knowledge gaps and unresolved challenges that warrant further inquiry. In particular, it delves into the key considerations when designing photosystems based on the chromophore and protein scaffold characteristics, presents the established strategies for artificial photosystems engineering with their advantages and disadvantages, and underscores the recent breakthroughs in understanding the molecular mechanisms governing light-harvesting, charge separation, and the role of the protein motions in the chromophore's excited state relaxation. By disseminating this knowledge, this article provides a foundational resource for defining the field of bio-hybrid photosystems and aims to inspire the continued exploration of artificial photosystems using protein design.

Green Wearable Sensors and Antennas for Bio-Medicine, Green Internet of Things, Energy Harvesting, and Communication Systems.

This paper presents innovations in green electronic and computing technologies. The importance and the status of the main subjects in green electronic and computing technologies are presented in this paper. In the last semicentennial, the planet suffered from rapid changes in climate. The planet is suffering from increasingly wild storms, hurricanes, typhoons, hard droughts, increases in seawater height, floods, seawater acidification, decreases in groundwater reserves, and increases in global temperatures. These climate changes may be irreversible if companies, organizations, governments, and individuals do not act daily and rapidly to save the planet. Unfortunately, the continuous growth in the number of computing devices, cellular devices, smartphones, and other smart devices over the last fifty years has resulted in a rapid increase in climate change. It is severely crucial to design energy-efficient "green" technologies and devices. Toxic waste from computing and cellular devices is rapidly filling up landfills and increasing air and water pollution. This electronic waste contains hazardous and toxic materials that pollute the environment and affect our health. Green computing and electronic engineering are employed to address this climate disaster. The development of green materials, green energy, waste, and recycling are the major objectives in innovation and research in green computing and electronics technologies. Energy-harvesting technologies can be used to produce and store green energy. Wearable active sensors and metamaterial antennas with circular split ring resonators (CSSRs) containing energy-harvesting units are presented in this paper. The measured bandwidth of the matched sensor is around 65% for VSWR, which is better than 3:1. The sensor gain is 14.1 dB at 2.62 GHz. A wideband 0.4 GHz to 6.4 GHz slot antenna with an RF energy-harvesting unit is presented in this paper. The Skyworks Schottky diode, SMS-7630, was used as the rectifier diode in the harvesting unit. If we transmit 20 dBm of RF power from a transmitting antenna that is located 0.2 m from the harvesting slot antenna at 2.4 GHz, the output voltage at the output port of the harvesting unit will be around 1 V. The power conversion efficiency of the metamaterial antenna dipole with metallic strips is around 75%. Wearable sensors with energy-harvesting units provide efficient, low-cost healthcare services that contribute to a green environment and minimize energy consumption. The measurement process and setups of wearable sensors are presented in this paper.

Optoelectronics Interfaces for a VLC System for UHD Audio-Visual Content Transmission in a Passenger Van: HW Design.

This work aims to provide the hardware (HW) design of the optoelectronics interfaces for a visible-light communication (VLC) system that can be employed for several use cases. Potential applications include the transmission of ultra-high-definition (UHD) streaming video through existing reading lamps installed in passenger vans. In this use case, visible light is employed for the downlink, while infrared light is used for the uplink channel, acting as a remote controller. Two primary components -a Light Fidelity (LiFi) router and a USB dongle-were designed and implemented. The 'LiFi Router', handling the downlink channel, comprises components such as a visible Light-Emitting Diode (LED) and an infrared receiver. Operating at a supply voltage of 12 V and consuming current at 920 mA, it is compatible with standard voltage buses found in transport vehicles. The 'USB dongle', responsible for the uplink, incorporates an infrared LED and a receiver optimized for visible light. The USB dongle works at a supply voltage of 5 V and shows a current consumption of 1.12 A, making it well suited for direct connection to a universal serial bus (USB) port. The bandwidth achieved for the downlink is 11.66 MHz, while the uplink's bandwidth is 12.27 MHz. A system competent at streaming UHD video with the feature of being single-input multiple-output (SIMO) was successfully implemented via the custom hardware design of the optical transceivers and optoelectronics interfaces. To ensure the system's correct performance at a distance of 110 cm, the minimum signal-to-noise ratio (SNRmin) for both optical links was maintained at 10.74 dB. We conducted a proof-of-concept test of the VLC system in a passenger van and verified its optimal operation, effectively illustrating its performance in a real operating environment. Exemplifying potential implementations possible with the hardware system designed in this work, a bit rate of 15.2 Mbps was reached with On-Off Keying (OOK), and 11.25 Mbps was obtained with Quadrature Phase Shift Keying (QPSK) using Orthogonal Frequency-Division Multiplexing (OFDM) obtaining a bit-error rate (BER) of 3.3259 × 10-5 in a passenger van at a distance of 72.5 cm between the LiFi router and the USB dongle. As a final addition, a solar panel was installed on the passenger van's roof to power the user's laptop and the USB dongle via a power bank battery. It took 13.4 h to charge the battery, yielding a battery life of 22.3 h. This characteristic renders the user's side of the system entirely self-powered.

Evaluating the Piezoelectric Energy Harvesting Potential of 3D-Printed Graphene Prepared Using Direct Ink Writing and Fused Deposition Modelling.

This research aims to use energy harvested from conductive materials to power microelectronic components. The proposed method involves using vibration-based energy harvesting to increase the natural vibration frequency, reduce the need for battery replacement, and minimise chemical waste. Piezoelectric transduction, known for its high-power density and ease of application, has garnered significant attention. Additionally, graphene, a non-piezoelectric material, exhibits good piezoelectric properties. The research explores a novel method of printing graphene material using 3D printing, specifically Direct Ink Writing (DIW) and fused deposition modelling (FDM). Both simulation and experimental techniques were used to analyse energy harvesting. The experimental technique involved using the cantilever beam-based vibration energy harvesting method. The results showed that the DIW-derived 3D-printed prototype achieved a peak power output of 12.2 µW, surpassing the 6.4 µW output of the FDM-derived 3D-printed prototype. Furthermore, the simulation using COMSOL Multiphysics yielded a harvested output of 0.69 µV.

A New Paradigm on Waste-to-Energy Applying Hydrovoltaic Energy Harvesting Technology to Face Masks.

The widespread use of single-use face masks during the recent epidemic has led to significant environmental challenges due to waste pollution. This study explores an innovative approach to address this issue by repurposing discarded face masks for hydrovoltaic energy harvesting. By coating the face masks with carbon black (CB) to enhance their hydrophilic properties, we developed mask-based hydrovoltaic power generators (MHPGs). These MHPGs were evaluated for their hydrovoltaic performance, revealing that different mask configurations and sizes affect their efficiency. The study found that MHPGs with smaller, more structured areas exhibited better energy output, with maximum open-circuit voltages (VOC) reaching up to 0.39 V and short-circuit currents (ISC) up to 65.6 µA. The integration of CB improved water absorption and transport, enhancing the hydrovoltaic performance. More specifically, MHPG-1 to MHPG-4, which represented different sizes and features, presented mean VOC values of 0.32, 0.17, 0.19 and 0.05 V, as well as mean ISC values of 16.57, 15.59, 47.43 and 3.02 µA, respectively. The findings highlight the feasibility of utilizing discarded masks in energy harvesting systems, offering both environmental benefits and a novel method for renewable energy generation. Therefore, this work provides a new paradigm for waste-to-energy (WTE) technologies and inspires further research into the use of unconventional waste materials for energy production.

Simultaneous low-frequency vibration isolation and energy harvesting via attachable metamaterials.

In this study, we achieved energy localization and amplification of flexural vibrations by utilizing the defect mode of plate-attachable locally resonant metamaterials, thereby realizing compact and low-frequency vibration energy suppression and energy harvesting with enhanced output performance. We designed a cantilever-based metamaterial unit cell to induce local resonance inside a periodic supercell structure and form a bandgap within the targeted low-frequency range of 300-450 Hz. Subsequently, a defect area was created by removing some unit cells to break the periodicity inside the metamaterial, which led to the isolation and localization of the vibration energy. This localized vibration energy was simultaneously converted into electrical energy by a piezoelectric energy harvester coupled with a metamaterial inside the defect area. Consequently, a substantially enhanced energy harvesting output power was achieved at 360 Hz, which was 43-times higher than that of a bare plate without metamaterials. The proposed local resonant metamaterial offers a useful and multifunctional platform with the capability of vibration energy isolation and harvesting, while exhibiting easy handling via attachable designs that can be tailored in the low-frequency regime.

Biomimetic Adaptive Building Façade Modeling for Sustainable Urban Freshwater Ecosystems: Integration of Nature's Water-Harvesting Strategy into Sun-Breakers.

Urban freshwater ecosystems have many critical functions, such as providing water to all living things and supporting biodiversity. Factors such as water pollution, increased water consumption, habitat loss, climate change, and drought threaten the health of urban freshwater ecosystems. Looking for solutions to these challenges, this article aims to recycle water and return it to its life cycle using a climate-sensitive water collection strategy. The model focuses on the biomimetic method as a basic strategy. In this regard, the concept of water-harvesting has been examined in detail by conducting a deep literature review, including architecture and engineering disciplines. With all these data obtained, a synthesis/integration study was carried out by developing a model proposal based on adaptive building façade elements to solve the water problems experienced in cities. The model proposal, which is directly related to the titles of "Clean Water and Sanitation (SDG 6)" and "Sustainable Cities and Communities (SDG 11)", which are among the Sustainable Development Goals (SDGs), aims to provide different perspectives on the disciplines with its superficial and functional features. In this context, it is anticipated that the article will become an indispensable resource for other researchers working on the subject.

Recent Advances in Wearable Textile-Based Triboelectric Nanogenerators.

We review recent results on textile triboelectric nanogenerators (T-TENGs), which function both as harvesters of mechanical energy and self-powered motion sensors. T-TENGs can be flexible, breathable, and lightweight. With a combination of traditional and novel manufacturing methods, including nanofibers, T-TENGs can deliver promising power output. We review the evolution of T-TENG device structures based on various textile material configurations and fabrication methods, along with demonstrations of self-powered systems. We also provide a detailed analysis of different textile materials and approaches used to enhance output. Additionally, we discuss integration capabilities with supercapacitors and potential applications across various fields such as health monitoring, human activity monitoring, human-machine interaction applications, etc. This review concludes by addressing the challenges and key research questions that remain for developing viable T-TENG technology.

Structural and spectroscopic characterization of the peridinin-chlorophyll a-protein (PCP) complex from Heterocapsa pygmaea (HPPCP).

Light harvesting proteins are optimized to efficiently collect and transfer light energy for photosynthesis. In eukaryotic dinoflagellates these complexes utilize chlorophylls and a special carotenoid, peridinin, and arrange them for efficient excitation energy transfer. At the same time, the carotenoids protect the system by quenching harmful chlorophyll triplet states. Here we use advanced spectroscopic techniques and X-ray structure analysis to investigate excitation energy transfer processes in the major soluble antenna, the peridinin chlorophyll a protein (PCP) from the free living dinoflagellate Heterocapsa pygmaea. We determined the 3D-structure of this complex at high resolution (1.2 Å). For better comparison, we improved the reference structure of this protein from Amphidinium carterae to a resolution of 1.15 Å. We then used fs and ns time-resolved absorption spectroscopy to study the mechanisms of light harvesting, but also of the photoprotective quenching of the chlorophyll triplet state. The photoprotection site was further characterized by Electron Spin Echo Envelope Modulation (ESEEM) spectroscopy to yield information on water molecules involved in triplet-triplet energy transfer. Similar to other PCP complexes, excitation energy transfer from peridinin to chlorophyll is found to be very efficient, with transfer times in the range of 1.6-2.1 ps. One of the four carotenoids, the peridinin 614, is well positioned to quench the chlorophyll triplet state with high efficiency and transfer times in the range of tens of picoseconds. Our structural and dynamic data further support, that the intrinsic water molecule coordinating the chlorophyll Mg ion plays an essential role in photoprotection.

Triboelectric Nanogenerator Made with Stretchable, Antibacterial Hydrogel Electrodes for Biomechanical Sensing.

Triboelectric nanogenerators (TENGs) have attracted widespread attention as a promising candidate for energy harvesting due to their flexibility and high power density. To meet diverse application scenarios, a highly stretchable (349%), conductive (1.87 S m-1), and antibacterial electrode composed of carbon quantum dots/LiCl/agar-polyacrylamide (CQDs/LiCl/agar-PAAm) dual-network (DN) hydrogel is developed for wearable TENGs. Notably, the concentration of agar alters the pore spacing and pore size of the DN hydrogel, thereby impacting the network cross-linking density and the migration of conductive ions (Li+ and Cl-). This variation further affects the mechanical strength and conductivity of the hydrogel electrode, thus modulating the mechanical stability and electrical output performance of the TENGs. With the optimal agar content, the tensile strength and conductivity of the hydrogel electrode increase by 211 and 719%, respectively. This enhancement ensures the stable output of TENGs during continuous operation (6000 cycles), with open-circuit voltage, short-circuit current, and transferred charge increasing by 200, 530, and 155%, respectively. Additionally, doping with CQDs enables the hydrogel electrode to effectively inhibit the Gram-negative bacterium Escherichia coli. Finally, the TENGs are utilized as a self-power smart ring for efficient and concise information transmission via Morse code. Consequently, this study introduces a creative approach for designing and implementing multifunctional, flexible wearable devices.

Patterned Hybrid Surfaces for Efficient Dew Harvesting.

Dew harvesting, minimally influenced by climate and geographical locations, is an ideal method for addressing water shortage problems. Superhydrophilic surfaces, characterized by their highest affinity for water, are particularly attractive for this purpose as they can attract more water molecules via condensation. However, a significant challenge arises from the high surface capillary force that impedes water from sliding down and being effectively collected. The resulting water film on the superhydrophilic surface tends to stay around the edge of the water collection surface, leading to evaporation loss and reduced collection efficacy. To overcome this problem, triangular patterns with low surface adhesion to water were introduced at the edge of superhydrophilic surfaces. This modification, achieved through a wet chemical method and masked oxygen plasma treatment, has significantly improved the efficiency of water collection. Results indicate that the hybrid surface reduced the time for the first water droplet to slide down by half and increased water collection efficiency by 78% compared to uniform superhydrophilic surfaces and by 536% compared to uniform superhydrophobic surfaces under a relative humidity of 55% with a temperature difference of 15 °C. The underlying principles were elucidated through computational simulations, and the mechanisms driving the enhancement in collection efficiency were explained.