Recent Progress of Thin Crystal Engineering for Perovskite Solar Cells.

Metal halide perovskite single crystals hold promise for photovoltaics with high efficiency and stability due to their superior optoelectronic properties and weak bulk ion migration. The past several years have witnessed rapid development of single-crystal perovskite solar cells (PSCs) with efficiency rocketed from 6.5% to 24.3%, however, which still lags behind their polycrystalline counterparts. Moreover, the poor device stability under light illumination is contrary to the high ion migration barrier of perovskite single crystals. The key limiting factors should be the low crystalline quality and high surface defect density of solution-grown thin single crystals. Under this circumstance, a review paper summarizing the recent progress and challenges will be instructive for future development of this emerging field. In this manuscript, the crystal engineering used to enhance carrier transport and suppress carrier recombination in vertical single-crystal PSCs will be summarized initially, including crystal growth, component control, surface and interface modification. Subsequently, the application of perovskite single crystals in lateral single-crystal PSCs will be discussed and compared with the conventionally vertical structure. Finally, the challenges and proposed strategies for the development of single-crystal PSCs are provided.

Host Engineering of Deep-Blue-Fluorescent Organic Light-Emitting Diodes with High Operational Stability and Narrowband Emission.

The realization of highly operationally stable blue organic light-emitting diodes (OLEDs) is a challenge in both academia and industry. This paper describes the development of anthracene-dibenzofuran host materials, 2-(10-(naphthalen-1-yl)anthracen-9-yl)naphtho[2,3-b]benzofuran (Host 1) and 2-(10-([1,1'-biphenyl]-2-yl)anthracen-9-yl)naphtho[2,3-b]benzofuran (Host 2), namely for use in the emissive layer of an OLED stack. A multiple-resonance thermally activated delayed serves as the blue fluorescence emitter and exhibits an initial luminance of 1000 cd m-2 and long operational stability (i.e., time to decay to 90% of initial luminance) of 249 h. Furthermore, a deep-blue OLED with an optimized top-emitting architecture with a high current efficiency of 154.3 cd A-1, is fabricated and calibrated to a Commission International de l'Éclairage y chromaticity coordinate of 0.048. Moreover, the emission spectrum of this OLED has a narrowband peak at 476 nm with a full width at half maximum (FWHM) of 16 nm. This work provides valuable insights into the design of anthracene-based host materials and highlights the importance of host optimization in improving the operational stability of OLEDs.

Operational stability study of lactate biosensors: modeling, parameter identification, and stability analysis.

Introduction: This paper investigates the operational stability of lactate biosensors, crucial devices in various biomedical and biotechnological applications. We detail the construction of an amperometric transducer tailored for lactate measurement and outline the experimental setup used for empirical validation. Methods: The modeling framework incorporates Brown and Michaelis-Menten kinetics, integrating both distributed and discrete delays to capture the intricate dynamics of lactate sensing. To ascertain model parameters, we propose a nonlinear optimization method, leveraging initial approximations from the Brown model's delay values for the subsequent model with discrete delays. Results: Stability analysis forms a cornerstone of our investigation, centering on linearization around equilibrium states and scrutinizing the real parts of quasi-polynomials. Notably, our findings reveal that the discrete delay model manifests marginal stability, occupying a delicate balance between asymptotic stability and instability. We introduce criteria for verifying marginal stability based on characteristic quasi-polynomial roots, offering practical insights into system behavior. Discussion: Qalitative examination of the model elucidates the influence of delay on dynamic behavior. We observe a transition from stable focus to limit cycle and period-doubling phenomena with increasing delay values, as evidenced by phase plots and bifurcation diagrams employing Poincaré sections. Additionally, we identify limitations in model applicability, notably the loss of solution positivity with growing delays, underscoring the necessity for cautious interpretation when employing delayed exponential function formulations. This comprehensive study provides valuable insights into the design and operational characteristics of lactate biosensors, offering a robust framework for understanding and optimizing their performance in diverse settings.

Unified Crystal Phase Control with MACl for Inducing Single-Crystal-Like Perovskite Thin Films in High-Pressure Fusion Toward High Efficiency Perovskite Solar Cell Modules.

Perovskite solar cells, recognized for their high photovoltaic conversion efficiency (PCE), cost-effectiveness, and simple fabrication, face challenges in PCE improvement due to structural defects in polycrystalline films. This study introduces a novel fabrication method for perovskite films using methylammonium chloride (MACl) to align grain orientation uniformly, followed by a high-pressure process to merge these grains into a texture resembling single-crystal perovskite. Employing advanced visual fluorescence microscopy, charge dynamics in these films are analyzed, uncovering the significant impact of grain boundaries on photo-generated charge transport within perovskite crystals. A key discovery is that optimal charge transport efficiency and speed occur in grain centers when the grain size exceeds 10 µm, challenging the traditional view that efficiency peaks when grain size surpasses film thickness to form a monolayer. Additionally, the presence of large-sized grains enhances ion activation energy, reducing ion migration under light and improving resistance to photo-induced degradation. In application, a perovskite solar cell module with large grains achieve a PCE of 22.45%, maintaining performance with no significant degradation under continuous white LED light at 100 mA cm-2 for over 1000 h. This study offers a new approach to perovskite film fabrication and insights into optimizing perovskite solar cell modules.

Low-Temperature Cross-Linked Hole Transport Layer for High-Performance Blue Quantum-Dot Light-Emitting Diodes.

Quantum-dot light-emitting diodes (QLEDs), a kind of promising optoelectronic device, demonstrate potential superiority in next-generation display technology. Thermal cross-linked hole transport materials (HTMs) have been employed in solution-processed QLEDs due to their excellent thermal stability and solvent resistance, whereas the unbalanced charge injection and high cross-linking temperature of cross-linked HTMs can inhibit the efficiency of QLEDs and limit their application. Herein, a low-temperature cross-linked HTM of 4,4'-bis(3-(((4-vinylbenzyl)oxy)methyl)-9H-carbazol-9-yl)-1,1'-biphenyl (DV-CBP) with a flexible styrene side chain is introduced, which reduces the cross-linking temperature to 150 °C and enhances the hole mobility up to 1.01 × 10-3 cm2 V-1 s-1. More importantly, the maximum external quantum efficiency of 21.35% is successfully obtained on the basis of the DV-CBP as a cross-linked hole transport layer (HTL) for blue QLEDs. The low-temperature cross-linked high-mobility HTL using flexible side chains could be an excellent alternative for future HTL development.

Bias-Switchable Dual-Mode Organic Photodetector with High Operational Stability Using Self-Trapped Cs3Cu2I5 Interfacial Layer.

Conventional photovoltaic (PV)-photodetectors are hard to detect fainted signals, while photomultiplication (PM)-capable devices indispensable for detecting weak light and are prone to degrade under strong light illumination and large bias, and it is urgent to realize highly efficient integrated detecting system with both PM and PV operation modes. In this work, one lead-free Cs3Cu2I5 nanocrystals with self-trapping exciton nature was introduced as interfacial layer adjacent to bulk and layer-by-layer heterojunction structure, and corresponding organic photodetectors with bias-switchable dual modes are demonstrated. The fabricated device exhibits low operating bias (0 V for PV mode and 0.8 V for PM mode), high specific detectivity (~1013 Jones), fast response speed as low as 1.59 µs, large bandwidth over 0.2 MHz and long-term operational stability last for 4 months in ambient condition. This synergy strategy also validated in different materials and device architectures, providing a convenient and scalable production process to develop highly efficient bias-switchable multi-functional organic optoelectrical applications.

Synergetic Electrostatic and Steric Effects in α-FAPbI3 Single Crystals For X-Ray Detection and Imaging.

It is still challenging to stabilize α-FAPbI3 perovskite for high performance optoelectrical devices. Herein, a novel strategy is proposed utilizing the synergetic electrostatic and steric effect to stabilize the α-FAPbI3 phase and suppress the ion migration. Dimethylamine (DMA+) cations are chosen as the dopant to fabricate FA0.96DMA0.04PbI3 single crystals (SCs). DFT calculations reveal that DMA+ cations can improve the stability of α-FAPbI3 phase in both thermodynamics (lower Gibbs free energy) and kinetics (higher defect formation and migration energy). The resulting SCs exhibit an environmental stability over 100 days and an extraordinary low dark current drift of 3.7 × 10-7 nA cm-1 s-1 V-1, comparable to 2D perovskite SCs. The X-ray detectors have also achieved the-state-of-the-art performance in X-ray detection and imaging. This work demonstrates the significance of electrostatic and steric effects in improving the phase and operational stability of perovskites.

Pattern-Matched Polymer Ligands Toward Near-Perfect Synergistic Passivation for High-Performance and Stable Br/Cl Mixed Perovskite Light-Emitting Diodes.

Mixed Br/Cl perovskite nanocrystals (PeNCs) exhibit bright pure-blue emission benefiting for fulfilling the Rec. 2100 standard. However, phase segregation remains a significant challenge that severely affects the stability and emission spectrum of perovskite light-emitting diodes (PeLEDs). Here, we demonstrate the optimization of the spacing between polydentate functional groups of polymer ligands to match the surface pattern of CsPbBr1.8Cl1.2 PeNCs, resulting in effective synergistic passivation effect and significant improvements in PeLED performances. The block and alternating copolymers with different inter-functional group spacing are facilely synthesized as ligands for PeNCs. Surprisingly, block copolymers with a higher functional group density do not match PeNCs, while alternating copolymers enable efficient PeNCs with the high photoluminescence intensity, low non-radiative recombination rate and high exciton binding energy. Density functional theory calculations clearly confirm the almost perfect match between alternating copolymers and PeNCs. Finally, pure-blue PeLEDs are achieved with the emission at 467 nm and Commission Internationale de l'Eclairage (CIE) coordinates of (0.131, 0.071), high external quantum efficiency (9.1 %) and record spectral and operational stabilities (~80 mins) in mixed-halide PeLEDs. Overall, this study contributes to designing the polymer ligands and promoting the development of high-performance and stable pure-color PeLEDs towards display applications.

Metal-Halide Perovskite Submicrometer-Thick Films for Ultra-Stable Self-Powered Direct X-Ray Detectors.

Metal-halide perovskites are revolutionizing the world of X-ray detectors, due to the development of sensitive, fast, and cost-effective devices. Self-powered operation, ensuring portability and low power consumption, has also been recently demonstrated in both bulk materials and thin films. However, the signal stability and repeatability under continuous X-ray exposure has only been tested up to a few hours, often reporting degradation of the detection performance. Here it is shown that self-powered direct X-ray detectors, fabricated starting from a FAPbBr3 submicrometer-thick film deposition onto a mesoporous TiO2 scaffold, can withstand a 26-day uninterrupted X-ray exposure with negligible signal loss, demonstrating ultra-high operational stability and excellent repeatability. No structural modification is observed after irradiation with a total ionizing dose of almost 200 Gy, revealing an unexpectedly high radiation hardness for a metal-halide perovskite thin film. In addition, trap-assisted photoconductive gain enabled the device to achieve a record bulk sensitivity of 7.28 C Gy-1 cm-3 at 0 V, an unprecedented value in the field of thin-film-based photoconductors and photodiodes for "hard" X-rays. Finally, prototypal validation under the X-ray beam produced by a medical linear accelerator for cancer treatment is also introduced.

Dynamic Reversible Oxidation-Reduction of Iodide Ions for Operationally Stable Perovskite Solar Cells under ISOS-L-3 Protocol.

Despite rapid advancements in the photovoltaic efficiencies of perovskite solar cells (PSCs), their operational stability remains a significant challenge for commercialization. This instability mainly arises from light-induced halide ion migration and subsequent oxidation into iodine (I2). The situation is exacerbated when considering the heat effects at elevated temperatures, leading to the volatilization of I2 and resulting in irreversible device degradation. Mercaptoethylammonium iodide (ESAI) is thus incorporated into perovskite as an additive to inhibit the oxidation of iodide anion (I-) and  the light-induced degradation pathway of FAPbI3→FAI+PbI2. Additionally, the formation of a thiol-disulfide/I--I2 redox pair within the perovskite film provides a dynamic mechanism for the continuous reduction of I2 under light and thermal stresses, facilitating the healing of iodine-induced degradations. This approach significantly enhances the operational stability of PSCs. Under the ISOS-L-3 testing protocol (maximum power point (MPP) tracking in an environment with relative humidity of ≈50% at ≈65 °C), the treated PSCs maintain 97% of their original power conversion efficieney (PCE) after 300 h of aging. In contrast, control devices exhibit almost complete degradation, primarily due to rapid thermal-induced I2 volatilization. These results demonstrate a promising strategy to overcome critical stability challenges in PSCs, particularly in scenarios involving thermal effects.

Enhancing Stability and Performance in Tin-Based Perovskite Field-Effect Transistors Through Hydrogen Bond Suppression of Organic Cation Migration.

Ion migration poses a substantial challenge in perovskite transistors, exerting detrimental effects on hysteresis and operational stability. This study focuses on elucidating the influence of ion migration on the performance of tin-based perovskite field-effect transistors (FETs). It is revealed that the high background carrier density in FASnI3 FETs arises not only from the oxidation of Sn2+ but also from the migration of FA+ ions. The formation of hydrogen bonding between FA+ and F- ions efficiently inhibits ion migration, leading to a reduction in background carrier density and an improvement in the operational stability of the transistors. The strategy of hydrogen bond is extended to fluorine-substituted additives to improve device performance. The incorporation of 4-fluorophenethylammonium iodide additives into FETs significantly minimizes the shift of turn-on voltage during cyclic measurements. Notably, an effective mobility of up to 30 cm2 V-1 s-1 with an Ion/off ratio of 107 is achieved. These findings hold promising potential for advancing tin-based perovskite technology in the field of electronics.

Application of a water-energy-carbon coupling index to evaluate the long-term operational stability of the anaerobic-anoxic-oxic-membrane bioreactor (A2/O-MBR) process under the influence of rainstorms.

In the context of global climate change, sudden rainstorms and typhoons induce fluctuations in hydraulic shocks to wastewater treatment plants (WWTPs) in coastal areas, causing two challenges of stable effluent quality and low-carbon operation. We established a quantitative evaluation method for resistance of wastewater treatment processes to hydraulic shocks based on the water-energy-carbon nexus using operational data from a WWTP in southeast coastal China from July 2018 to December 2022. The effects of hydraulic shocks on the operational stability of the anaerobic-anoxic-oxic-membrane bioreactor (A2/O-MBR) process were analyzed following five steps. The results showed that the gray water footprint (GWF) of the process was 9.3% lower than that of the A2/O process. The energy footprint (ENF) and carbon footprint (CF) were approximately 2.1 times and 1.7 times higher than those of the A2/O process, respectively. The resistance to hydraulic shocks of the A2/O-MBR process is approximately 5.5 times higher than that of the A2/O process. In conclusion, the A2/O-MBR process exhibits higher process operational stability when subjected to hydraulic shocks, which is more conducive to the efficient and stable operation of WWTPs in rainstorm and typhoon-prone areas. The evaluation methodology provides qualitative technical support for selecting upgrading processes for WWTPs in different regions.

Bright and Stable Red Perovskite LEDs under High Current Densities.

Perovskite LEDs (PeLEDs) have emerged as a next-generation light-emitting technology. Recent breakthroughs were made in achieving highly stable near-infrared and green PeLEDs. However, the operational lifetimes (T50) of visible PeLEDs under high current densities (>10 mA cm-2) remain unsatisfactory (normally <100 h), limiting the possibilities in solid-state lighting and AR/VR applications. This problem becomes more pronounced for mixed-halide (e.g., red and blue) perovskite emitters in which critical challenges such as halide segregation and spectral instability are present. Here, we demonstrate bright and stable red PeLEDs based on mixed-halide perovskites, showing measured T50 lifetimes of up to ∼357 h at currents of ≥25 mA cm-2, a record for the operational stability of visible PeLEDs under high current densities. The devices produce intense and stable emission with a maximum luminance of 28,870 cd m-2 (radiance: 1584 W sr-1 m-2), which is record-high for red PeLEDs. Key to this demonstration is the introduction of sulfonamide, a dipolar molecular stabilizer that effectively interacts with the ionic species in the perovskite emitters. It suppresses halide segregation and migration into the charge-transport layers, resulting in enhanced stability and brightness of the mixed-halide PeLEDs. These results represent a substantial step toward bright and stable PeLEDs for emerging applications.

Uracil Induced Simultaneously Strengthening Grain Boundaries and Interfaces Enables High-Performance Perovskite Solar Cells with Superior Operational Stability.

The operational stability is a huge obstacle to further commercialization of perovskite solar cells. To address this critical issue, in this work, uracil is introduced as a "binder" into the perovskite film to simultaneously improve the power conversion efficiency (PCE) and operational stability. Uracil can efficiently passivate defects and strengthen grain boundaries to enhance the stability of perovskite films. Moreover, the uracil also strengthens the interface between the perovskite and the Tin oxide (SnO2 ) electron transport layer to increase the binding force. The uracil-modified devices deliver a champion PCE of 24.23% (certificated 23.19%) with negligible hysteresis at active area of 0.0625 cm2 . In particular, the optimal device exhibits over 90% of its initial PCE after tracking for ≈6000 h at its maximum power point under continuous light, indicating its superior operational stability. Moreover, the devices also show great reproducibility in both PCE and operational stability.

B-N Covalent Bond Embedded Double Hetero-[n]helicenes for Pure Red Narrowband Circularly Polarized Electroluminescence with High Efficiency and Stability.

Chiral B/N embedded multi-resonance (MR) emitters open a new paradigm of circularly polarized (CP) organic light-emitting diodes (OLEDs) owing to their unique narrowband spectra. However, pure-red CP-MR emitters and devices remain exclusive in literature. Herein, by introducing a B-N covalent bond to lower the electron-withdrawing ability of the para-positioned B-π-B motif, the first pair of pure-red double hetero-[n]helicenes (n = 6 and 7) CP-MR emitter peaking 617 nm with a small full-width at half-maximum of 38 nm and a high photoluminescence quantum yield of ≈100% in toluene is developed. The intense mirror-image CP light produced by the enantiomers is characterized by high photoluminescence dissymmetry factors (gPL ) of +1.40/-1.41 × 10-3 from their stable helicenes configuration. The corresponding devices using these enantiomers afford impressive CP electroluminescence dissymmetry factors (gEL ) of +1.91/-1.77 × 10-3 , maximum external quantum efficiencies of 36.6%/34.4% and Commission Internationale de I'Éclairage coordinates of (0.67, 0.33), exactly satisfying the red-color requirement specified by National Television Standards Committee (NTSC) standard. Notably a remarkable long LT95 (operational time to 95% of the initial luminance) of ≈400 h at an initial brightness of 10,000 cd m-2 is also observed for the same device, representing the most stable CP-OLED up to date.

Bilayer 2D-3D Perovskite Heterostructures for Efficient and Stable Solar Cells.

With a stacking-layered architecture, the bilayer two-dimensional-three-dimensional (2D-3D) perovskite heterostructure (PHS) not only eliminates surface defects but also protects the 3D perovskite matrix from external stimuli. However, these bilayer 2D-3D PHSs suffer from impaired interfacial charge carrier transport due to the relatively insulating 2D perovskite fragments with a random phase distribution. Over the past decade, substantial efforts have been devoted to pioneering molecular and structural designs of the 2D perovskite interlayers for improving their charge carrier mobility, which enables state-of-the-art perovskite solar cells with high power conversion efficiency and exceptional operational stability. Herein, this review offers a comprehensive and up-to-date overview on the recent progress of bilayer 2D-3D PHSs, encompassing advancements on spacer cation engineering, interfacial charge carrier modification, advanced deposition protocols, and characterization techniques. Then, the evolutionary trajectory of bilayer 2D-3D PHSs is outlined by summarizing its mainstream development trends, followed by a perspective discussion about its future research opportunities toward efficient and durable perovskite solar cells.

Interfacial Passivation Engineering for Highly Efficient Quantum Dot Light-Emitting Diodes via Aromatic Amine-Functionalized Dipole Molecules.

Blue quantum dot (QD) light-emitting diodes (QLEDs) exhibit unsatisfactory operational stability and electroluminescence (EL) properties due to severe nonradiative recombination induced by large numbers of dangling bond defects and charge imbalance in QD. Herein, dipolar aromatic amine-functionalized molecules with different molecular polarities are employed to regulate charge transport and passivate interfacial defects between QD and the electron transfer layer (ETL). The results show that the stronger the molecular polarity, especially with the -CF3 groups possessing a strong electron-withdrawing capacity, the more effective the defect passivation of S and Zn dangling bonds at the QD surface. Moreover, the dipole interlayer can effectively reduce electron injection into QD at high current density, enhancing charge balance and mitigating Joule heat. Finally, blue QLEDs exhibit a peak external quantum efficiency (EQE) of 21.02% with an operational lifetime (T50 at 100 cd m-2) exceeding 4000 h.

New Nanophotonics Approaches for Enhancing the Efficiency and Stability of Perovskite Solar Cells.

Over the past decade, the power conversion efficiency (PCE) of perovskite solar cells (PSCs) has experienced a remarkable ascent, soaring from 3.8% in 2009 to a remarkable record of 26.1% in 2023. Many recent approaches for improving PSC performance employ nanophotonic technologies, from light harvesting and thermal management to the manipulation of charge carrier dynamics. Plasmonic nanoparticles and arrayed dielectric nanostructures have been applied to tailor the light absorption, scattering, and conversion, as well as the heat dissipation within PSCs to improve their PCE and operational stability. In this review, it is begin with a concise introduction to define the realm of nanophotonics by focusing on the nanoscale interactions between light and surface plasmons or dielectric photonic structures. Prevailing strategies that utilize resonance-enhanced light-matter interactions for boosting the PCE and stability of PSCs from light trapping, carrier transportation, and thermal management perspectives are then elaborated, and the resultant practical applications, such as semitransparent photovoltaics, colored PSCs, and smart perovskite windows are discussed. Finally, the state-of-the-art nanophotonic paradigms in PSCs are reviewed, and the benefits of these approaches in improving the aesthetic effects and energy-saving character of PSC-integrated buildings are highlighted.

Surface Modulation via Conjugated Bithiophene Ammonium Salt for Efficient Inverted Perovskite Solar Cells.

The metal halide perovskite absorbers are prone to surface defects, which severely limit the power conversion efficiencies (PCEs) and the operational stability of the perovskite solar cells (PSCs). Herein, trace amounts of bithiophene propylammonium iodide (bi-TPAI) are applied to modulate the surface properties of the gas-quenched perovskite. It is found that the bi-TPAI surface treatment has negligible impact on the perovskite morphology, but it can induce a defect passivation effect and facilitate the charge carrier extraction, contributing to the gain in the open-circuit voltage (Voc) and fill factor. As a result, the PCE of the gas-quenched sputtered NiOx-based inverted PSCs is enhanced from the initial 20.0% to 22.0%. Most importantly, the bi-TPAI treatment can largely alleviate or even eliminate the burn-in process during the maximum power point tracking measurement, improving the operational stability of the devices.

Highly Effective and Efficient Self-Assembled Multilayer-Based Electrode Passivation for Operationally Stable and Reproducible Electrolyte-Gated Transistor Biosensors.

To ensure the operational stability of transistor-based biosensors in aqueous electrolytes during multiple measurements, effective electrode passivation is crucially important for reliable and reproducible device performances. This paper presents a highly effective and efficient electrode passivation method using a facile solution-processed self-assembled multilayer (SAML) with excellent insulation property to achieve operational stability and reproducibility of electrolyte-gated transistor (EGT) biosensors. The SAML is created by the consecutive self-assembly of three different molecular layers of 1,10-decanedithiol, vinyl-polyhedral oligomeric silsesquioxane, and 1-octadecanethiol. This passivation enables EGT to operate stably in phosphate-buffered saline (PBS) during repeated measurements over multiple cycles without short-circuiting. The SAML-passivated EGT biosensor is fabricated with a solution-processed In2O3 thin film as an amorphous oxide semiconductor working both as a semiconducting channel in the transistor and as a functionalizable biological interface for a bioreceptor. The SAML-passivated EGT including In2O3 thin film is demonstrated for the detection of Tau protein as a biomarker of Alzheimer's disease while employing a Tau-specific DNA aptamer as a bioreceptor and a PBS solution with a low ionic strength to diminish the charge-screening (Debye length) effect. The SAML-passivated EGT biosensor functionalized with the Tau-specific DNA aptamer exhibits ultrasensitive, quantitative, and reliable detection of Tau protein from 1 × 10-15 to 1 × 10-10 M, covering a much larger range than clinical needs, via changes in different transistor parameters. Therefore, the SAML-based passivation method can be effectively and efficiently utilized for operationally stable and reproducible transistor-based biosensors. Furthermore, this presented strategy can be extensively adapted for advanced biomedical devices and bioelectronics in aqueous or physiological environments.