Reversible oxidation of ethylene on ferroelectric BaTiO3(001): An X-ray photoelectron spectroscopy study.

Adsorption and desorption of ethylene on BaO-terminated (001) barium titanate are investigated by X-ray photoelectron spectroscopy. Carbon is found in an oxidized state, at a binding energy similar to that resulting from CO adsorption on BaTiO3(001). The amount of carbon adsorbed on the surface is also similar to the case of CO/BaTiO3(001). Upon heating the substrate up to the loss of its ferroelectric polarization, the C 1s signal from the oxidized spectral region vanishes. At the same time, there was no noticeable oxygen depletion of the surface after repeated C2H4 adsorption and desorption. The substrate remains stable after repeated oxidative adsorption and desorption of ethylene. Desorption occurs at different temperatures, depending on the adsorption temperature, which suggests different adsorption geometries: non-dissociated adsorption at high temperature with ethylene bond on two surface oxygen atoms, and locally dissociated adsorption at lower temperatures, in "formaldehyde-like" local configurations.

Composite Photocatalysts with Fe, Co, and Ni Oxides on Supports with Tetracoordinated Ti Embedded into Aluminosilicate Gel during Zeolite Y Synthesis.

Ti-aluminosilicate gels were used as supports for the immobilization of Fe, Co, and Ni oxides (5%) by impregnation and synthesis of efficient photocatalysts for the degradation of ß-lactam antibiotics from water. Titanium oxide (1 and 2%) was incorporated into the zeolite network by modifying the gel during the zeolitization process. The formation of the zeolite Y structure and its microporous structure were evidenced by X-ray diffraction and N2 physisorption. The structure, composition, reduction, and optical properties were studied by X-ray diffraction, H2-TPR, XPS, Raman, photoluminescence, and UV-Vis spectroscopy. The obtained results indicated a zeolite Y structure for all photocatalysts with tetracoordinated Ti4+ sites. The second transitional metals supported by the post-synthesis method were obtained in various forms, such as oxides and/or in the metallic state. A red shift of the absorption edge was observed in the UV-Vis spectra of photocatalysts upon the addition of Fe, Co, or Ni species. The photocatalytic performances were evaluated for the degradation of cefuroxime in water under visible light irradiation. The best results were obtained for iron-immobilized photocatalysts. Scavenger experiments explained the photocatalytic results and their mechanisms. A different contribution of the active species to the photocatalytic reactions was evidenced.

Co- and Ni-Doped TiO2 Nanoparticles Supported on Zeolite Y with Photocatalytic Properties.

Zeolite Y samples with microporous and hierarchical structures containing Ti-Ni and Ti-Co oxides were obtained as active photocatalysts. Different Ti amounts (5, 10% TiO2) were supported, followed by the loading of Ni or Co oxides (5%). X-ray diffraction evidenced the presence of TiO2 as an anatase. N2 adsorption-desorption results showed type IV isotherms for hierarchical zeolite Y samples, and a combination of type IV and I isotherms for zeolite Y samples. UV-Vis diffuse reflectance spectra showed a shift in the absorption band to visible with increasing Ti loading and especially after Co and Ni addition. A significant effect of the support was evidenced for Ti and its interaction with Co/Ni species. The zeolite Y support stabilized Ti in the 4+ oxidation state while hierarchical zeolite Y support favored the formation of Ti3+ species, Ni0 and Ni2+ and the oxidation of Co to 3+ oxidation state. Photocatalytic activity, under UV and visible light irradiation, was evaluated by the degradation of amoxicillin, used as a model test. The photocatalytic mechanism was investigated using ethanol, p-benzoquinone and KI as ·OH and ·O2- radicals and hole (h+) scavengers. The best results were obtained for the immobilized Ni-Ti species on the hierarchical zeolite Y support.

Surface charge dynamics on air-exposed ferroelectric Pb(Zr,Ti)O3(001) thin films.

Probing of the free surface ferroelectric properties of thin polar films can be achieved either by estimating the band bending variance under the top-most layer or by studying the extent of the extrinsic charge accumulated outside the surface. Photoemitted or incoming low-energy electrons can be used to characterize locally both properties in a spectromicroscopic approach. Thin ferroelectric lead zirco-titanate (PZT) is investigated by combining low energy/mirror electron microscopy (LEEM/MEM) with photoemission electron microscopy (PEEM) and high-resolution photoelectron spectroscopy (XPS). Significant extrinsic negative compensation charge is proven to accumulate on the surface of the outward polarized thin film, indicated by high MEM-LEEM transition values, up to 15.3 eV, and is correlated with the surface electrostatic potential, which can be partially screened either by electrons interacting with the sample or by soft X-rays through the ejection of secondary electrons and generation of positive charge under the surface. A radiation-induced surface charge compensation effect is observed. The study indicates that air-exposed high quality ferroelectric thin films show large negative surface potentials, determined locally on the surface, which are nevertheless sensitive to beam damage and molecular desorption. These values represent a confirmation of previously estimated surface potential energy values determined from the LEED data on clean surfaces.

Copper-/Zinc-Doped TiO2 Nanopowders Synthesized by Microwave-Assisted Sol-Gel Method.

Using the microwave-assisted sol-gel method, Zn- and Cu-doped TiO2 nanoparticles with an anatase crystalline structure were prepared. Titanium (IV) butoxide was used as a TiO2 precursor, with parental alcohol as a solvent and ammonia water as a catalyst. Based on the TG/DTA results, the powders were thermally treated at 500 °C. XRD and XRF revealed the presence of a single-phase anatase and dopants in the thermally treated nanoparticles. The surface of the nanoparticles and the oxidation states of the elements were studied using XPS, which confirmed the presence of Ti, O, Zn, and Cu. The photocatalytic activity of the doped TiO2 nanopowders was tested for the degradation of methyl-orange (MO) dye. The results indicate that Cu doping increases the photoactivity of TiO2 in the visible-light range by narrowing the band-gap energy.

Photocatalytic and Antibacterial Properties of Doped TiO2 Nanopowders Synthesized by Sol-Gel Method.

For environmental applications, nanosized TiO2-based materials are known as the most important photocatalyst and are intensively studied for their advantages such as their higher activity, lower price, and chemical and photoresist properties. Zn or Cu doped TiO2 nanoparticles with anatase crystalline structure were synthesized by sol-gel process. Titanium (IV) butoxide was used as a TiO2 precursor, with parental alcohol as a solvent, and a hydrolysing agent (ammonia-containing water) was added to obtain a solution with pH 10. The gels were characterized by TG/DTA analysis, SEM, and XPS. Based on TG/DTA results, the temperature of 500 °C was chosen for processing the powders in air. The structure of the samples thermally treated at 500 °C was analysed by XRD and the patterns show crystallization in a single phase of TiO2 (anatase). The surface of the samples and the oxidation states was investigated by XPS, confirming the presence of Ti, O, Zn and Cu. The antibacterial activity of the nanoparticle powder samples was verified using the gram-positive bacterium Staphylococcus aureus. The photocatalytic efficiency of the doped TiO2 nanopowders for degradation of methyl orange (MO) is here examined in order to evaluate the potential applications of these materials for environmental remediation.

Palladium/palladium oxide coated electrospun fibers for wearable sweat pH-sensors.

The work describes the development of a flexible, hydrogel embedded pH-sensor that can be integrated in inexpensive wearable and non-invasive devices at epidermal level for electrochemical quantification of H+ ions in sweat. Such a device can be useful for swift, real time diagnosis and for monitoring specific conditions. The sensors' working electrodes are flexible poly(methyl methacrylate) electrospun fibers coated with a thin gold layer and electrochemically functionalized with nanostructured palladium/palladium oxide. The response to H+ ions is investigated by cyclic voltammetry and electrochemical impedance spectroscopy while open circuit potential measurements show a sensitivity of aprox. -59 mV per pH unit. The modification of the sensing interface upon basic and acid treatment is characterized by scanning and transmission electron microscopy and the chemical composition by X-ray photoelectron spectroscopy. In order to demonstrate the functionality of the pH-sensor at epidermal level, as a wearable device, the palladium/palladium oxide working electrode and silver/silver chloride reference electrode are embedded within a pad of polyacrylamide hydrogel and measurements in artificial sweat over a broad pH range were performed. Sensitivity up to -28 mV/pH unit, response time below 30 s, temperature dependence of approx. 1 mV/°C as well as the minimum volume to which the sensor responses of 250 nanoliters were obtained for this device. The proposed configuration represents a viable alternative making use of low-cost and fast fabrication processes and materials.

Direct Immobilization of Biomolecules through Magnetic Forces on Ni Electrodes via Ni Nanoparticles: Applications in Electrochemical Biosensors.

The present work describes a new simple procedure for the direct immobilization of biomolecules on Ni electrodes using magnetic Ni nanoparticles (NiNPs) as biomolecule carriers. Ni electrodes were fabricated by electroplating, and NiNPs were chemically synthesized. The chemical composition, crystallinity, and granular size of Ni electrodes, NiNP, and NiNP-modified Ni electrodes (NiNP/Ni) were determined by X-ray diffraction, scanning electron microscopy, and X-ray photoelectron spectroscopy (XPS). The electrochemical characterization of Ni electrodes by cyclic voltammetry and electrochemical impedance spectroscopy confirmed the existence of nickel oxides, hydroxides, and oxohydroxide films at the surface of Ni. Magnetic characterization and micromagnetic simulations were performed in order to prove that the magnetic force is responsible for the immobilization process. Further, Ni electrodes were employed as amperometric sensors for the detection of hydrogen peroxide because it is an important performance indicator for a material to be applied in biosensing. The working principle for magnetic immobilization of the enzyme-functionalized NiNP, without the use of external magnetic sources, was demonstrated for glucose oxidase (GOx) as a model enzyme. XPS results enabled to identify the presence of GOx attached to the NiNP (GOx-NiNP) on Ni electrodes. Finally, glucose detection and quantification were evaluated with the newly developed GOx-NiNP/Ni biosensor by amperometry at different potentials, and control experiments at different electrode materials in the presence and absence of NiNP demonstrated their importance in the biosensor architecture.

Polarization landscape effects in soft X-ray-induced surface chemical decomposition of lead zirco-titanate, evidenced by photoelectron spectromicroscopy.

The stability of thin films of lead zirco-titanate (PZT) under intense soft X-ray beams is investigated by time-resolved photoelectron spectromicroscopy with a lateral resolution below 1 micrometer. Surface dissociation is observed when samples are irradiated with intense (5 × 1023 photons per s per m2) soft X-rays, with promotion of reduced lead on the surface. On areas exhibiting outwards polarization (P(+)), the reduced lead is formed at the expense of P(+)-PZT. On areas presenting co-existing P(+) states with areas without out-of-plane polarization (P(0)), the reduced lead is formed at the expense of the P(0)-PZT component, while the P(+)-PZT remains constant. The main dissociation mechanism was found to be triggered by 'hot' electrons in the conduction band, with energies exceeding the surface dissociation energies. Dissociation occurs basically when the electron affinity is larger than the dissociation energy of PbO (for P(+) areas) or PbO- (for P(0) areas). Such mechanisms may be adapted for dissociation of other molecules on surfaces of ferroelectric thin films or for quantifying the stability of ferroelectric surfaces interacting with other radiation, with applications in the fields of photocatalysis or photovoltaic devices.

Unveiling the Mechanisms Leading to H2 Production Promoted by Water Decomposition on Epitaxial Graphene at Room Temperature.

By means of a combination of surface-science spectroscopies and theory, we investigate the mechanisms ruling the catalytic role of epitaxial graphene (Gr) grown on transition-metal substrates for the production of hydrogen from water. Water decomposition at the Gr/metal interface at room temperature provides a hydrogenated Gr sheet, which is buckled and decoupled from the metal substrate. We evaluate the performance of Gr/metal interface as a hydrogen storage medium, with a storage density in the Gr sheet comparable with state-of-the-art materials (1.42 wt %). Moreover, thermal programmed reaction experiments show that molecular hydrogen can be released upon heating the water-exposed Gr/metal interface above 400 K. The Gr hydro/dehydrogenation process might be exploited for an effective and eco-friendly device to produce (and store) hydrogen from water, i.e., starting from an almost unlimited source.

Epitaxial growth of a single-domain hexagonal boron nitride monolayer.

We investigate the structure of epitaxially grown hexagonal boron nitride (h-BN) on Ir(111) by chemical vapor deposition of borazine. Using photoelectron diffraction spectroscopy, we unambiguously show that a single-domain h-BN monolayer can be synthesized by a cyclic dose of high-purity borazine onto the metal substrate at room temperature followed by annealing at T=1270 K, this method giving rise to a diffraction pattern with 3-fold symmetry. In contrast, high-temperature borazine deposition (T=1070 K) results in a h-BN monolayer formed by domains with opposite orientation and characterized by a 6-fold symmetric diffraction pattern. We identify the thermal energy and the binding energy difference between fcc and hcp seeds as key parameters in controlling the alignment of the growing h-BN clusters during the first stage of the growth, and we further propose structural models for the h-BN monolayer on the Ir(111) surface.

Room Temperature Ferromagnetic, Anisotropic, Germanium Rich FeGe(001) Alloys.

Ferromagnetic FexGe1-x with x = 2%-9% are obtained by Fe deposition onto Ge(001) at high temperatures (500 °C). Low energy electron diffraction (LEED) investigation evidenced the preservation of the (1 × 1) surface structure of Ge(001) with Fe deposition. X-ray photoelectron spectroscopy (XPS) at Ge 3d and Fe 2p core levels evidenced strong Fe diffusion into the Ge substrate and formation of Ge-rich compounds, from FeGe3 to approximately FeGe2, depending on the amount of Fe deposited. Room temperature magneto-optical Kerr effect (MOKE) evidenced ferromagnetic ordering at room temperature, with about 0.1 Bohr magnetons per Fe atom, and also a clear uniaxial magnetic anisotropy with the in-plane easy magnetization axis. This compound is a good candidate for promising applications in the field of semiconductor spintronics.