Extremely anisotropic van der Waals thermal conductors.

The densification of integrated circuits requires thermal management strategies and high thermal conductivity materials1-3. Recent innovations include the development of materials with thermal conduction anisotropy, which can remove hotspots along the fast-axis direction and provide thermal insulation along the slow axis4,5. However, most artificially engineered thermal conductors have anisotropy ratios much smaller than those seen in naturally anisotropic materials. Here we report extremely anisotropic thermal conductors based on large-area van der Waals thin films with random interlayer rotations, which produce a room-temperature thermal anisotropy ratio close to 900 in MoS2, one of the highest ever reported. This is enabled by the interlayer rotations that impede the through-plane thermal transport, while the long-range intralayer crystallinity maintains high in-plane thermal conductivity. We measure ultralow thermal conductivities in the through-plane direction for MoS2 (57 ± 3 mW m-1 K-1) and WS2 (41 ± 3 mW m-1 K-1) films, and we quantitatively explain these values using molecular dynamics simulations that reveal one-dimensional glass-like thermal transport. Conversely, the in-plane thermal conductivity in these MoS2 films is close to the single-crystal value. Covering nanofabricated gold electrodes with our anisotropic films prevents overheating of the electrodes and blocks heat from reaching the device surface. Our work establishes interlayer rotation in crystalline layered materials as a new degree of freedom for engineering-directed heat transport in solid-state systems.

Odd-even effect on the thermal conductivity of liquid crystalline epoxy resins.

Rapid developments in high-performance computing and high-power electronics are driving needs for highly thermal conductive polymers and their composites for encapsulants and interface materials. However, polymers typically have low thermal conductivities of ∼0.2 W/(m K). We studied the thermal conductivity of a series of epoxy resins cured by one diamine hardener and seven diepoxide monomers with different precise ethylene linker lengths (x = 2-8). We found pronounced odd-even effects of the ethylene linker length on the liquid crystalline order, mass density, and thermal conductivity. Epoxy resins with even x have liquid crystalline structure with the highest density of 1.44 g/cm3 and highest thermal conductivity of 1.0 W/(m K). Epoxy resins with odd x are amorphous with the lowest density of 1.10 g/cm3 and lowest thermal conductivity of 0.17 W/(m K). These findings indicate that controlling precise linker length in dense networks is a powerful route to molecular design of thermally conductive polymers.

Ionic Peltier effect in Li-ion electrolytes.

The coupled transport of charge and heat provide fundamental insights into the microscopic thermodynamics and kinetics of materials. We describe a sensitive ac differential resistance bridge that enables measurements of the temperature difference on two sides of a coin cell with a resolution of better than 10 µK. We use this temperature difference metrology to determine the ionic Peltier coefficients of symmetric Li-ion electrochemical cells as a function of Li salt concentration, solvent composition, electrode material, and temperature. The Peltier coefficients Π are negative, i.e., heat flows in the direction opposite to the drift of Li ions in the applied electric field, large, -Π > 30 kJ mol-1, and increase with increasing temperature at T > 300 K. The Peltier coefficient is approximately constant on time scales that span the characteristic time for mass diffusion across the thickness of the electrolyte, suggesting that heat of transport plays a minor role in comparison to the changes in partial molar entropy of Li at the interface between the electrode and electrolyte. Our work demonstrates a new platform for studying the non-equilibrium thermodynamics of electrochemical cells and provides a window into the transport properties of electrochemical materials through measurements of temperature differences and heat currents that complement traditional measurements of voltages and charge currents.

Boosting Plant Photosynthesis with Carbon Dots: A Critical Review of Performance and Prospects.

Artificially augmented photosynthesis in nano-bionic plants requires tunable nano-antenna structures with physiochemical and optoelectronic properties, as well as unique light conversion capabilities. The use of nanomaterials to promote light capture across photosystems, primarily by carbon dots, has shown promising results in enhancing photosynthesis through tunable uptake, translocation, and biocompatibility. Carbon dots possess the ability to perform both down and up-light conversions, making them effective light promoters for harnessing solar energy beyond visible light wavelengths.This review presents and discusses the recent progress in fabrication, chemistry, and morphology, as well as other properties such as photoluminescence and energy conversion efficiency of nano-antennas based on carbon dots. The performance of artificially boosted photosynthesis is discussed and then correlated with the conversion properties of carbon dots and how they are applied to plant models. The challenges related to the nanomaterial delivery and the performance evaluation practices in modified photosystems, consideration of the reliability of this approach, and the potential avenues for performance improvements through other types of nano-antennas based on alternative nanomaterials are also critically evaluated. It is anticipated that this review will stimulate more high-quality research in plant nano-bionics and provide avenues to enhance photosynthesis for future agricultural applications.

Graphene as a nano-delivery vehicle in agriculture - current knowledge and future prospects.

Graphene has triggered enormous interest in, and exploration of, its applications in diverse areas of science and technology due to its unique properties. While graphene has displayed great potential as a nano-delivery system for drugs and biomolecules in biomedicine, its application as a nanocarrier in agriculture has only begun to be explored. Conventional fertilizers and agricultural delivery systems have a number of disadvantages, such as: fast release of the active ingredient, low delivery efficiency, rapid degradation and low stability that often leads to their over-application and consequent environmental problems. Advanced nano fertilizers with high carrier efficiency and slow and controlled release are now considered the gold standard for promoting agricultural sustainability while protecting the environment. Graphene's attractive properties include large surface area, chemical stability, mechanical stability, tunable surface chemistry and low toxicity making it a promising material on which to base agricultural delivery systems. Recent research has demonstrated considerable success in the use of graphene for agricultural applications, including its utilization as a delivery vehicle for plant nutrients and crop protection agents, as well as in post-harvest management of crops. This review, therefore, presents a comprehensive overview of the current status of graphene-based nanocarriers in agriculture. Additionally, the review outlines the surface functionalization methods used for effective molecular delivery, various strategies for nano-vehicle design and the underlying features necessary for a graphene-based agro-delivery system. Finally, the review discusses directions for further research in optimization of graphene-based nanocarriers.

Prospects of chloroplast metabolic engineering for developing nutrient-dense food crops.

Addressing nutritional deficiencies in food crops through biofortification is a sustainable approach to tackling malnutrition. Biofortification is continuously being attempted through conventional breeding as well as through various plant biotechnological interventions, ranging from molecular breeding to genetic engineering and genome editing for enriching crops with various health-promoting metabolites. Genetic engineering is used for the rational incorporation of desired nutritional traits in food crops and predominantly operates through nuclear and chloroplast genome engineering. In the recent past, chloroplast engineering has been deployed as a strategic tool to develop model plants with enhanced nutritional traits due to the various advantages it offers over nuclear genome engineering. However, this approach needs to be extended for the nutritional enhancement of major food crops. Further, this platform could be combined with strategies, such as synthetic biology, chloroplast editing, nanoparticle-mediated rapid chloroplast transformation, and horizontal gene transfer through grafting for targeting endogenous metabolic pathways for overproducing native nutraceuticals, production of biopharmaceuticals, and biosynthesis of designer nutritional compounds. This review focuses on exploring various features of chloroplast genome engineering for nutritional enhancement of food crops by enhancing the levels of existing metabolites, restoring the metabolites lost during crop domestication, and introducing novel metabolites and phytonutrients needed for a healthy daily diet.

Designer nanoparticles for plant cell culture systems: Mechanisms of elicitation and harnessing of specialized metabolites.

Plant cell culture systems have become an attractive and sustainable approach to produce high-value and commercially significant metabolites under controlled conditions. Strategies involving elicitor supplementation into plant cell culture media are employed to mimic natural conditions for increasing the metabolite yield. Studies on nanoparticles (NPs) that have investigated elicitation of specialized metabolism have shown the potential of NPs to be a substitute for biotic elicitors such as phytohormones and microbial extracts. Customizable physicochemical characteristics allow the design of monodispersed-, stimulus-responsive-, and hormone-carrying-NPs of precise geometries to enhance their elicitation capabilities based on target metabolite/plant cell culture type. We contextualize advances in NP-mediated elicitation, especially stimulation of specialized metabolic pathways, the underlying mechanisms, impacts on gene regulation, and NP-associated cytotoxicity. The novelty of the concept lies in unleashing the potential of designer NPs to enhance yield, harness metabolites, and transform nanoelicitation from exploratory investigations to a commercially viable strategy.

Metabolites derived from fungi and bacteria suppress in vitro growth of Gnomoniopsis smithogilvyi, a major threat to the global chestnut industry.

INTRODUCTION: Chestnut rot caused by the fungus Gnomoniopsis smithogilvyi is a disease present in the world's major chestnut growing regions. The disease is considered a significant threat to the global production of nuts from the sweet chestnut (Castanea sativa). Conventional fungicides provide some control, but little is known about the potential of biological control agents (BCAs) as alternatives to manage the disease. OBJECTIVE: Evaluate whether formulated BCAs and their secreted metabolites inhibit the in vitro growth of G. smithogilvyi. METHODS: The antifungal potential of BCAs was assessed against the pathogen through an inverted plate assay for volatile compounds (VOCs), a diffusion assay for non-volatile compounds (nVOCs) and in dual culture. Methanolic extracts of nVOCs from the solid medium were further evaluated for their effect on conidia germination and were screened through an LC-MS-based approach for antifungal metabolites. RESULTS: Isolates of Trichoderma spp., derived from the BCAs, significantly suppressed the pathogen through the production of VOCs and nVOCs. The BCA from which Bacillus subtilis was isolated was more effective in growth inhibition through the production of nVOCs. The LC-MS based metabolomics on the nVOCs derived from the BCAs showed the presence of several antifungal compounds. CONCLUSION: The results show that G. smithogilvyi can be effectively controlled by the BCAs tested and that their use may provide a more ecological alternative for managing chestnut rot. The in vitro analysis should now be expanded to the field to assess the effectiveness of these alternatives for chestnut rot management.

Recreating in vitro tripartite mycorrhizal associations through functional bacterial biofilms.

Arbuscular mycorrhizal fungi (AMF) and beneficial bacteria are found naturally associated with most terrestrial plant roots. While it is now well known that bacteria colonize AMF and can form aggregates and biofilms, little is known about how interactions between bacterial communities and AMF take place under both in situ and in vitro conditions. We investigated the impact of inoculation with AMF-associated bacteria (AABs) of AMF by in vitro recreation of the interaction on synthetic growth media in a two-compartment Petri plate system. The inoculated AABs were found to be associated with the mycorrhizal co-culture and were found to migrate along growing AMF hyphae and to be associated with the spore surface. AABs differentially influenced the growth of the AMF and their functional capability demonstrated by analysis of phosphate solubilization, nitrogen fixation, and biofilm formation. We have thus characterized these important interactions adding to a further understanding of the synergistic relationship between the two cross-kingdom microbial partners. KEY POINTS: • An in vitro assay was utilized to recreate functional biofilms with AMF-associated bacteria. • AMF-associated bacteria formed a biofilm and enhanced sporulation of Rhizophagus irregularis. • AMF-bacterial interactions through biofilm formation influence the functional capability of both partners.

Light-triggered thermal conductivity switching in azobenzene polymers.

Materials that can be switched between low and high thermal conductivity states would advance the control and conversion of thermal energy. Employing in situ time-domain thermoreflectance (TDTR) and in situ synchrotron X-ray scattering, we report a reversible, light-responsive azobenzene polymer that switches between high (0.35 W m-1 K-1) and low thermal conductivity (0.10 W m-1 K-1) states. This threefold change in the thermal conductivity is achieved by modulation of chain alignment resulted from the conformational transition between planar (trans) and nonplanar (cis) azobenzene groups under UV and green light illumination. This conformational transition leads to changes in the π-π stacking geometry and drives the crystal-to-liquid transition, which is fully reversible and occurs on a time scale of tens of seconds at room temperature. This result demonstrates an effective control of the thermophysical properties of polymers by modulating interchain π-π networks by light.

Marker counter-selection via CRISPR/Cas9 co-targeting for efficient generation of genome edited avian cell lines and germ cells.

Efficient isolation of genetically modified cells that are phenotypically indistinguishable from the unmodified cells remains a major technical barrier for the broader utilization of CRISPR/Cas9. Here, we report a novel enrichment approach to select the genome engineered cells by co-targeting a genomically integrated GFP gene along with the endogenous gene of interest (GOI). Using this co-targeting approach, multiple genomic loci were successfully targeted in chicken (DF1) and quail (CEC-32) fibroblast cell lines by transient transfection of Cas9 and guide RNAs (gRNAs). Clonal isolation of co-targeted DF1 cells showed 75% of cell clones had deletion of GFP and biallelic deletion of the GOI. To assess the utility of this approach to generate genome modified animals, we tested it on chicken primordial germ cells (PGCs) expressing GFP by co-targeting with gRNAs against GFP and endogenous ovomucoid (OVM) gene. PGCs enriched for loss of GFP and confirmed for OVM deletion, derived by co-targeting, were injected into Hamburger and Hamilton stage 14-15 chicken embryos, and their ability to migrate to the genital ridge was confirmed. This simple, efficient enrichment approach could easily be applied to the creation of knock-out or edited cell lines or animals.

Role of Thin Film Adhesion on Capillary Peeling.

The capillary force can peel off a substrate-attached film if the adhesion energy (Gw) is low. Capillary peeling has been used as a convenient, rapid, and nondestructive method for fabricating free-standing thin films. However, the critical value of Gw, which leads to the transition between peeling and sticking, remains largely unknown. As a result, capillary peeling remains empirical and applicable to a limited set of materials. Here, we investigate the critical value of Gw and experimentally show the critical adhesion (Gw,c) to scale with the water-film interfacial energy (≈0.7γfw), which corresponds well with our theoretical prediction of Gw,c = γfw. Based on the critical adhesion, we propose quantitative thermodynamic guidelines for designing thin film interfaces that enable successful capillary peeling. The outcomes of this work present a powerful technique for thin film transfer and advanced nanofabrication in flexible photovoltaics, battery materials, biosensing, translational medicine, and stretchable bioelectronics.

Good Solid-State Electrolytes Have Low, Glass-Like Thermal Conductivity.

Thermal management in Li-ion batteries is critical for their safety, reliability, and performance. Understanding the thermal conductivity of the battery materials is crucial for controlling the temperature and temperature distribution in batteries. This work provides systemic quantitative measurements of the thermal conductivity of three important classes of solid electrolytes (SEs) over the temperature range 150 < T < 350 K. Studies include the oxides Li1.5 Al0.5 Ge1.5 (PO4 )3 and Li6.4 La3 Zr1.4 Ta0.6 O12 , sulfides Li2 S-P2 S5 , Li6 PS5 Cl, and Na3 PS4 , and halides Li3 InCl6 and Li3 YCl6 . Thermal conductivities of sulfide and halide SEs are in the range 0.45-0.70 W m-1  K-1 ; thermal conductivities of Li6.4 La3 Zr1.4 Ta0.6 O12 and Li1.5 Al0.5 Ge1.5 (PO4 )3 are 1.4 and 2.2 W m-1  K-1 , respectively. For most of the SEs studied in this work, the thermal conductivity increases with increasing temperature, that is, the thermal conductivity has a glass-like temperature dependence. The measured room-temperature thermal conductivities agree well with the calculated minimum thermal conductivities indicating that the phonon mean-free-paths in these SEs are close to an atomic spacing. The low, glass-like thermal conductivity of the SEs investigated is attributed to the combination of their complex crystal structures and the atomic-scale disorder induced by the materials processing methods that are typically needed to produce high ionic conductivities.

Induction of spermatogenesis in men with hypogonadotropic hypogonadism.

PURPOSE: We compared our clinical experience to international standards, assessed by response to treatment and pregnancy rates to ensure our results were comparable. METHODS: Men presenting with azoospermia related to hypogonadism were recruited into a treatment programme which was managed by one person over 8 years in a secondary care facility. Treatment followed published management plans using urinary gonadotropins. Data were collected on success rates in spermatogenesis, as well as variables which might predict success, and costs. Statistical analysis used non-parametric methods. RESULTS: Of 16 men with HH, 14 achieved spermatogenesis, and 9 had sperm cryopreserved. Of those 14, 6 were successful in achieving a pregnancy with their partner from assisted conception (including ICSI) and one after natural conception. Factors identified to identify men likely to be successful in treatment were whether testicular volume was larger at onset of gonadotropins (median 10 mL) with a trend towards greater success if the cause developed after puberty. Mean treatment costs per man treated amounted to GP£4379/UD$5377 (figures for September 2020). Success rates from this treatment should exceed 70% in most clinical settings. The likelihood of success improves when testicular volume exceeded 10 mL at initiation of treatment and a trend exists whereby success is more likely whereby when hypogonadism developed after puberty. Treatment costs are at a level likely to benefit quality of life, supporting the delivery of this treatment and where necessary and possible, funding it in line with other fertility treatments. This treatment should be available much more widely as a management option for men with hypogonadism, allowing them to father a biological child, rather than using donor sperm.

Condensation Induced Blistering as a Measurement Technique for the Adhesion Energy of Nanoscale Polymer Films.

Polymeric coatings having micro-to-nanoscale thickness show immense promise for enhancing thermal transport, catalysis, energy conversion, and water collection. Characterizing the work of adhesion (G) between these coatings and their substrates is key to understanding transport physics as well as mechanical reliability. Here, we demonstrate that water vapor condensation blistering is capable of in situ measurement of work of adhesion at the interface of polymer thin films with micrometer spatial resolution. We use our method to characterize adhesion of interfaces with controlled chemistry such as fluorocarbon/fluorocarbon (CFn/CFm, n, m = 0-3), fluorocarbon/hydrocarbon (CFn/CHm), fluorocarbon/silica (CFn/SiO2), and hydrocarbon/silica (CHn/SiO2) interfaces showing excellent agreement with adhesion energy measured by the contact angle approach. We demonstrate the capability of our condensation blister test to achieve measurement spatial resolutions as low as 10 µm with uncertainties of ∼10%. The outcomes of this work establish a simple tool to study interfacial adhesion.

Oxidative Catabolism of (+)-Pinoresinol Is Initiated by an Unusual Flavocytochrome Encoded by Translationally Coupled Genes within a Cluster of (+)-Pinoresinol-Coinduced Genes in Pseudomonas sp. Strain SG-MS2.

Burkholderia sp. strain SG-MS1 and Pseudomonas sp. strain SG-MS2 have previously been found to mineralize (+)-pinoresinol through a common catabolic pathway. Here, we used comparative genomics, proteomics, protein semipurification, and heterologous expression to identify a flavoprotein from the vanillyl alcohol oxidase/p-cresol methyl hydroxylase (VAO/PCMH) enzyme family in SG-MS2 that carries out the initial hydroxylation of (+)-pinoresinol at the benzylic carbon. The cognate gene is translationally coupled with a downstream cytochrome gene, and the cytochrome is required for activity. The flavoprotein has a unique combination of cofactor binding and cytochrome requirements for the VAO/PCMH family. The heterologously expressed enzyme has a Km of 1.17 µM for (+)-pinoresinol. The enzyme is overexpressed in strain SG-MS2 upon exposure to (+)-pinoresinol, along with 45 other proteins, 22 of which were found to be encoded by genes in an approximately 35.1-kb cluster also containing the flavoprotein and cytochrome genes. Homologs of 18 of these 22 genes, plus the flavoprotein and cytochrome genes, were also found in a 38.7-kb cluster in SG-MS1. The amino acid identities of four of the other proteins within the SG-MS2 cluster suggest they catalyze conversion of hydroxylated pinoresinol to protocatechuate and 2-methoxyhydroquinone. Nine other proteins upregulated in SG-MS2 on exposure to (+)-pinoresinol appear to be homologs of proteins known to comprise the protocatechuate and 2-methoxyhydroquinone catabolic pathways, but only three of the cognate genes lie within the cluster containing the flavoprotein and cytochrome genes.IMPORTANCE (+)-Pinoresinol is an important plant defense compound, a major food lignan for humans and some other animals, and the model compound used to study degradation of the ß-ß' linkages in lignin. We report a gene cluster, in one strain each of Pseudomonas and Burkholderia, that is involved in the oxidative catabolism of (+)-pinoresinol. The flavoprotein component of the α-hydroxylase which heads the pathway belongs to the 4-phenol oxidizing (4PO) subgroup of the vanillyl alcohol oxidase/p-cresol methyl hydroxylase (VAO/PCMH) enzyme family but constitutes a novel combination of cofactor and electron acceptor properties for the family. It is translationally coupled with a cytochrome gene whose product is also required for activity. The work casts new light on the biology of (+)-pinoresinol and its transformation to other bioactive molecules. Potential applications of the findings include new options for deconstructing lignin into useful chemicals and the generation of new phytoestrogenic enterolactones from lignans.

Ultralow thermal conductivity of turbostratically disordered MoSe2 ultra-thin films and implications for heterostructures.

Films containing 8, 16, 24, 32 and 64 MoSe2 layers were synthesized using the modulated elemental reactants method. X-ray reflectivity patterns showed that the annealed films were the targeted number of MoSe2 layers thick with atomically smooth interfaces. In-plane x-ray diffraction (XRD) scans contained only hk0 reflections for crystalline MoSe2 monolayers. Specular XRD patterns contained only 00l reflections, also indicating that the hk0 plane of the MoSe2 layers are parallel to the substrate. Both XRD and electron microscopy techniques indicated that the hk0 planes are rotationally disordered with respect to one another, with all orientations equally probable for large areas. The rotational disorder between MoSe2 layers is present even when analyzed spots are within 10 nm of one another. Cross-plane thermal conductivities of 0.07-0.09 W m-1 K-1 were measured by time domain thermoreflectance, with the thinnest films exhibiting the lowest conductivity. The structural analysis suggests that the ultralow thermal conductivity is a consequence of rotational disorder, which increases the separation between MoSe2 layers. The bonding environment of the Se atoms also becomes significantly distorted from C 3v symmetry due to the rotational disorder between layers. This structural disorder efficiently reduces the group velocity of the transverse phonon modes but not that of longitudinal modes. Since rotational disorder between adjacent layers in heterostructures is expected if the constituents have incommensurate lattices, this study indicates that these heterostructures will have very low cross-plane thermal conductivity.

Isolation of the (+)-Pinoresinol-Mineralizing Pseudomonas sp. Strain SG-MS2 and Elucidation of Its Catabolic Pathway.

Pinoresinol is a dimer of two ß-ß'-linked coniferyl alcohol molecules. It is both a plant defense molecule synthesized through the shikimic acid pathway and a representative of several ß-ß-linked dimers produced during the microbial degradation of lignin in dead plant material. Until now, little has been known about the bacterial catabolism of such dimers. Here we report the isolation of the efficient (+)-pinoresinol-mineralizing Pseudomonas sp. strain SG-MS2 and its catabolic pathway. Degradation of pinoresinol in this strain is inducible and proceeds via a novel oxidative route, which is in contrast to the previously reported reductive transformation by other bacteria. Based on enzyme assays and bacterial growth, cell suspension, and resting cell studies, we provide conclusive evidence that pinoresinol degradation in strain SG-MS2 is initiated by benzylic hydroxylation, generating a hemiketal via a quinone methide intermediate, which is then hydrated at the benzylic carbon by water. The hemiketal, which stays in equilibrium with the corresponding keto alcohol, undergoes an aryl-alkyl cleavage to generate a lactone and 2-methoxyhydroquinone. While the fate of 2-methoxyhydroquinone is not investigated further, it is assumed to be assimilated by ring cleavage. The lactone is further metabolized via two routes, namely, lactone ring cleavage and benzylic hydroxylation via a quinone methide intermediate, as described above. The resulting hemiketal again exists in equilibrium with a keto alcohol. Our evidence suggests that both routes of lactone metabolism lead to vanillin and vanillic acid, which we show can then be mineralized by strain SG-MS2.IMPORTANCE The oxidative catabolism of (+)-pinoresinol degradation elucidated here is fundamentally different from the reductive cometabolism reported for two previously characterized bacteria. Our findings open up new opportunities to use lignin for the biosynthesis of vanillin, a key flavoring agent in foods, beverages, and pharmaceuticals, as well as various new lactones. Our work also has implications for the study of new pinoresinol metabolites in human health. The enterodiol and enterolactone produced through reductive transformation of pinoresinol by gut microbes have already been associated with decreased risks of cancer and cardiovascular diseases. The metabolites from oxidative metabolism we find here also deserve attention in this respect.

Novel self-assembling conjugates as vectors for agrochemical delivery.

BACKGROUND: Modern agricultural practises rely on surfactant-based spray applications to eliminate weeds in crops. The wide spread and indiscriminate use of surfactants may result in a number of deleterious effects that are not limited to impacts on the crop and surrounding farm eco-system but include effects on human health. To provide a safer alternative to the use of surfactant-based formulations, we have synthesised a novel, self-assembling herbicide conjugate for the delivery of a broad leaf herbicide, picloram. RESULTS: The synthesized self-assembling amphiphile-picloram (SAP) conjugate has three extending arms: a lipophilic lauryl chain, a hydrophilic polyethylene glycol chain and the amphiphobic agrochemical active picloram. We propose that the SAP conjugate maintains its colloidal stability by quickly transitioning between micellar and inverse micellar phases in hydrophilic and lipophilic environments respectively. The SAP conjugate provides the advantage of a phase structure that enables enhanced interaction with the hydrophobic epicuticular wax surface of the leaf. We have investigated the herbicidal efficiency of the SAP conjugate compared against that of commercial picloram formulations using the model plant Arabidopsis thaliana and found that when tested at agriculturally relevant doses between 0.58 and 11.70 mM a dose-dependent herbicidal effect with comparable kill rates was evident. CONCLUSION: Though self-assembling drug carriers are not new to the pharmaceutical industry their use for the delivery of agrochemicals shows great promise but is largely unexplored. We have shown that SAP may be used as an alternative to current surfactant-based agrochemical formulations and has the potential to shift present practises towards a more sustainable approach.

Delivery of Abscisic Acid to Plants Using Glutathione Responsive Mesoporous Silica Nanoparticles.

An intracellular glutathione (GSH) responsive phytochemical delivery system based on thiol gated mesoporous silica nanoparticles (MSNs) was developed and tested on the model plant Arabidopsis thaliana. In the present study, monodispersed MSNs with particle diameters of ~20 nm and pore sizes of ~2.87 nm were synthesized and modified. Abscisic acid (ABA), a key phytohormone, was entrapped in the mesopores of MSNs and then the pore entrances of MSNs were covered with decanethiol gatekeepers through GSH-cleavable disulfide linkages. An in vitro release test of ABA from decanethiol gated MSNs proved that there was efficient loading and entrapment of phytochemicals in the absence of a GSH redox trigger. Most importantly, in planta experiments demonstrated that GSH-mediated release of ABA from the pores of MSNs significantly reduced the leaf stomatal aperture and inhibited water loss of treated plants. Moreover, compared with the usage of free ABA, the controlled release of the encapsulated phytohormone from MSNs markedly prolonged the expression of the ABA inducible marker gene (AtGALK2) and finally, improved the drought resistance ability of Arabidopsis seedlings under drought stress. Therefore, the concept of using short-chain molecules as gatekeepers to encapsulate biomolecules in MSNs was demonstrated. The application of MSNs with redox-responsive gatekeepers has been shown in this study to be a potential and efficient technique to deliver phytochemicals into plants and release them in a controllable fashion.