Railway Axle Early Fatigue Crack Detection through Condition Monitoring Techniques.

The detection of cracks in rotating machinery is an unresolved issue today. In this work, a methodology for condition monitoring of railway axles is presented, based on crack detection by means of the automatic selection of patterns from the vibration signal measurement. The time waveforms were processed using the Wavelet Packet Transform, and appropriate alarm values for diagnosis were calculated automatically using non-supervised learning techniques based on Change Point Analysis algorithms. The validation was performed using vibration signals obtained during fatigue tests of two identical railway axle specimens, one of which cracked during the test while the other did not. During the test in which the axle cracked, the results show trend changes in the energy of the vibration signal associated with theoretical defect frequencies, which were particularly evident in the direction of vibration that was parallel to the track. These results are contrasted with those obtained during the test in which the fatigue limit was not exceeded, and the test therefore ended with the axle intact, verifying that the effects that were related to the crack did not appear in this case. With the results obtained, an adjusted alarm value for a condition monitoring process was established.

Railway Axle Condition Monitoring Technique Based on Wavelet Packet Transform Features and Support Vector Machines.

Railway axles are critical to the safety of railway vehicles. However, railway axle maintenance is currently based on scheduled preventive maintenance using Nondestructive Testing. The use of condition monitoring techniques would provide information about the status of the axle between periodical inspections, and it would be very valuable in the prevention of catastrophic failures. Nevertheless, in the literature, there are not many studies focusing on this area and there is a lack of experimental data. In this work, a reliable real-time condition-monitoring technique for railway axles is proposed. The technique was validated using vibration measurements obtained at the axle boxes of a full bogie installed on a rig, where four different cracked railway axles were tested. The technique is based on vibration analysis by means of the Wavelet Packet Transform (WPT) energy, combined with a Support Vector Machine (SVM) diagnosis model. In all cases, it was observed that the WPT energy of the vibration signals at the first natural frequency of the axle when the wheelset is first installed (the healthy condition) increases when a crack is artificially created. An SVM diagnosis model based on the WPT energy at this frequency demonstrates good reliability, with a false alarm rate of lower than 10% and defect detection for damage occurring in more than 6.5% of the section in more than 90% of the cases. The minimum number of wheelsets required to build a general model to avoid mounting effects, among others things, is also discussed.

Effective Crack Detection in Railway Axles Using Vibration Signals and WPT Energy.

Crack detection for railway axles is key to avoiding catastrophic accidents. Currently, non-destructive testing is used for that purpose. The present work applies vibration signal analysis to diagnose cracks in real railway axles installed on a real Y21 bogie working on a rig. Vibration signals were obtained from two wheelsets with cracks at the middle section of the axle with depths from 5.7 to 15 mm, at several conditions of load and speed. Vibration signals were processed by means of wavelet packet transform energy. Energies obtained were used to train an artificial neural network, with reliable diagnosis results. The success rate of 5.7 mm defects was 96.27%, and the reliability in detecting larger defects reached almost 100%, with a false alarm ratio lower than 5.5%.

New support roller profile design for railway wheel re-profiling process by under-floor lathes with a single cutting tool.

The wheel re-profiling is an important part of railway wheelset maintenance. Researchers and railway operators have been very concerned about how to minimize the loss of time during wheel re-profiling without decreasing safety. Avoiding wheelset disassembly means considerable time savings, while reducing wheel damage during operation. Underfloor wheel lathes are the most appropriate tool to achieve this double objective, and therefore the most used nowadays. Multi-cut tool lathes have the disadvantage of being extremely expensive. On the other hand, with single tool lathes, re-profiling is not smooth or safe enough when current convex profile support rollers are used. It is well known by the companies that during reprofiling the wheel suffers impacts/damaged. In this article, a methodology to optimize the profile of the support rollers used in underfloor single tool lathes for railway wheel re-profiling is proposed. This novel profile design will minimize damage and increase the safety of such lathes, since it proposes a greater smoothness in the process. Simulations of re-profiling process have been carried out by the finite element method showing that the designed roller profile reduces drastically the impact/damage during the operation. The impact generated between the re-profiling wheel and the rollers is avoided. Profile-optimized support rollers have been used in a real underfloor wheel lathe, showing good results.

Author Correction: Polycyclic aromatic chains on metals and insulating layers by repetitive [3+2] cycloadditions.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

Polycyclic aromatic chains on metals and insulating layers by repetitive [3+2] cycloadditions.

The vast potential of organic materials for electronic, optoelectronic and spintronic devices entails substantial interest in the fabrication of π-conjugated systems with tailored functionality directly at insulating interfaces. On-surface fabrication of such materials on non-metal surfaces remains to be demonstrated with high yield and selectivity. Here we present the synthesis of polyaromatic chains on metallic substrates, insulating layers, and in the solid state. Scanning probe microscopy shows the formation of azaullazine repeating units on Au(111), Ag(111), and h-BN/Cu(111), stemming from intermolecular homo-coupling via cycloaddition reactions of CN-substituted polycyclic aromatic azomethine ylide (PAMY) intermediates followed by subsequent dehydrogenation. Matrix-assisted laser desorption/ionization (MALDI) mass spectrometry demonstrates that the reaction also takes place in the solid state in the absence of any catalyst. Such intermolecular cycloaddition reactions are promising methods for direct synthesis of regioregular polyaromatic polymers on arbitrary insulating surfaces.