Hybrid argon plasma coagulation (HybridAPC) versus sharp excision for the treatment of endometriosis: a prospective randomized clinical trial.

PURPOSE: Endometriosis is a benign, but potentially serious gynaecological condition in terms of abdominal pain and impaired fertility. Laparoscopic excision techniques are considered the therapeutic standard. HybridAPC is presented as a novel technique for the non-contact thermal ablation of peritoneal endometriosis with simultaneous protection of the underlying thermosensitive structures by creating a needle-free elevated fluid cushion which enables a safer exposure and distance, as well as potentially improved peritoneal conditioning prior to APC. METHODS: In this prospective randomized clinical trial, 39 patients with 132 superficial endometriotic lesions in total were treated with HybridAPC or sharp excision in an initial laparoscopic procedure according to randomization. In a second-look laparoscopy, adhesion formation was rated macroscopically. Histologic samples were taken from previously treated areas for evaluation of eradication rate. RESULTS: The eradication rate was not significantly different between HybridAPC treatment and sharp excision (65 vs. 81%, p = .55). Adhesions formed in 5% of HybridAPC-treated lesions and in 10% after sharp excision (p = .49). HybridAPC treatment was significantly faster than sharp excision (69 vs. 106 s, p < .05). No intra- and postoperative complications were registered. CONCLUSION: This clinical trial demonstrates the feasibility of this novel surgical technique with a promising impact on adhesion prevention. Compared to sharp excision, HybridAPC is likely to be a safe, tissue-preserving, and fast method for the treatment of peritoneal endometriosis.

A new bipolar device for sealing and cutting: ex and in vivo studies for performance evaluation.

INTRODUCTION: A novel multipurpose bipolar radiofrequency instrument, the Erbe Dissector (EDS), which simultaneously seals and cuts tissue, was developed. Ex vivo sealing rate and time, burst pressure, jaw temperature and thermal spread were studied in porcine renal arteries. MATERIAL AND METHODS: In vivo, 13 surgical tasks were performed in two pigs: beside sealing rate and time, overall performance in sharp and blunt dissection, tissue sticking, hemostasis, precision, etc., were evaluated by four surgeons compared with ENSEAL G2 (EG2) using surveys on a Likert scale (1 = very poor; 5 = very good). RESULTS: Ex vivo, the EDS sealing rate was 91.7% (33/36 arteries) at an average sealing time of 2.1 s (range 1.7-2.8) and a burst pressure of 1040 ± 350 mmHg. The maximum jaw temperature was 87 ± 4 °C and the mean lateral thermal spread was 0.8 ± 0.2 mm. In vivo, the sealing rate for arteries and veins was 92.6% (50/54) and the median seal and cut time was 1.6 s (range: 1.3-2.9). The average EDS performance score across all tasks was 4.4 ± 0.6 Likert points. For five shared tasks, EDS was better than EG2 (4.4 ± 0.5 versus 3.4 ± 0.6 Likert points; p = 0.016). CONCLUSIONS: EDS seals and cuts arteries and veins rapidly with good safety and user-friendliness.

Rapid and precise delivery of cells in the urethral sphincter complex by a novel needle-free waterjet technology.

OBJECTIVES: To investigate the therapy of stress urinary incontinence in a preclinical setting cells were injected into the urethrae of minipigs; however, cells injected by William's needle were frequently misplaced or lost; thus, we investigated if needle-free cell injections using a novel waterjet technology facilitates precise injections in the urethral sphincter complex. MATERIALS AND METHODS: Porcine adipose tissue-derived stromal cells (pADSCs) were isolated from boars, expanded, labelled, and injected in the sphincter of female pigs by waterjet employing two different protocols. After incubation for 15 min or 3 days, the urethrae of the pigs were examined. Injected cells were visualised by imaging and fluorescence microscopy of tissue sections. DNA of injected male cells was verified by polymerase chain reaction (PCR) of the sex-determining region (SRY) gene. Cell injections by William's needle served as controls. RESULTS: The new waterjet technology delivered pADSCs faster and with better on-site precision than the needle injections. Bleeding during or after waterjet injection or other adverse effects, such as swelling or urinary retention, were not observed. Morphologically intact pADSCs were detected in the urethrae of all pigs treated by waterjet. SRY-PCR of chromosomal DNA and detection of recombinant green fluorescent protein verified the injection of viable cells. In contrast, three of four pigs injected by William's needle displayed no or misplaced cells. CONCLUSION: Transurethral injection of viable pADSCs by waterjet is a simple, fast, precise, and yet gentle new technology. This is the first proof-of-principle concept study providing evidence that a waterjet injects intact cells exactly in the tissue targeted in a preclinical in vivo situation. To further explore the clinical potential of the waterjet technology longer follow-up, as well as incontinence models have to be studied.

Novel Techniques to Improve Precise Cell Injection.

We noted recently that the injection of cells with a needle through a cystoscope in the urethral sphincter muscle of pigs failed to deposit them nearby or at the intended target position in about 50% of all animals investigated (n > 100). Increasing the chance for precise cell injection by shotgun approaches employing several circumferential injections into the sphincter muscle bears the risk of tissue injury. In this study, we developed and tested a novel needle-free technique to precisely inject cells in the urethral sphincter tissue, or other tissues, using a water-jet system. This system was designed to fit in the working channels of endoscopes and cystoscopes, allowing a wide range of minimally invasive applications. We analyze key features, including the physical parameters of the injector design, pressure ranges applicable for tissue penetration and cell injections and biochemical parameters, such as different compositions of injection media. Our results present settings that enable the high viability of cells post-injection. Lastly, the method is suitable to inject cells in the superficial tissue layer and in deeper layers, required when the submucosa or the sphincter muscle of the urethra is targeted.

Injection of Porcine Adipose Tissue-Derived Stromal Cells by a Novel Waterjet Technology.

Previously, we developed a novel, needle-free waterjet (WJ) technology capable of injecting viable cells by visual guided cystoscopy in the urethral sphincter. In the present study, we aimed to investigate the effect of WJ technology on cell viability, surface markers, differentiation and attachment capabilities, and biomechanical features. Porcine adipose tissue-derived stromal cells (pADSCs) were isolated, expanded, and injected by WJ technology. Cell attachment assays were employed to investigate cell-matrix interactions. Cell surface molecules were analyzed by flow cytometry. Cells injected by Williams Needle (WN), normal cannula, or not injected cells served as controls. Biomechanical properties were assessed by atomic force microscopy (AFM). pADSCs injected by the WJ were viable (85.9%), proliferated well, and maintained their in vitro adipogenic and osteogenic differentiation capacities. The attachment of pADSCs was not affected by WJ injection and no major changes were noted for cell surface markers. AFM measurements yielded a significant reduction of cellular stiffness after WJ injections (p < 0.001). WJ cell delivery satisfies several key considerations required in a clinical context, including the fast, simple, and reproducible delivery of viable cells. However, the optimization of the WJ device may be necessary to further reduce the effects on the biomechanical properties of cells.

A novel waterjet technology for transurethral cystoscopic injection of viable cells in the urethral sphincter complex.

AIMS: In a recent preclinical study, we noticed that injection of cells in the urethral sphincter by needle through a cystoscope under visual control frequently yielded in misplacement or loss of cells. We, therefore, investigated if a needle-free waterjet device delivers viable cells under defined settings, including injection volume and pressure, fluid velocity and transportation media, precisely through the urothelium and connective tissue close to the sphincter muscle without full penetration of the sphincter apparatus. METHODS: Mesenchymal stromal cells (MSCs) were prepared for needle-free waterjet injections. Upon injections into liquids cell viability and yield were investigated by trypan blue dye exclusion. Upon injection into cadaveric urethral tissue samples, cells were isolated from the urethrae and expanded to prove that this novel method delivered viable cells into the tissue. MSC injections by William's needle served as controls. RESULTS: Waterjet injections of MSCs into isotonic cell culture medium resulted in equal or better yields of viable cells when compared with needle injections. Upon injection in urethral tissue samples, the waterjet technology facilitated fast and precise injections of viable cells through urothelial, mucosal and submucosal layers to reach the sphincter muscle. By controlling the injection pressure, loss of cells due to insufficient thrust or unintended full penetration was avoided. CONCLUSIONS: Needle-free waterjet injections deliver cells in the urethra faster and more precisely when compared with needle injections without compromising their viability. This is the first proof-of-concept study providing evidence that a waterjet transports viable cells precisely into the targeted tissue.

Evaluation of Efficacy of a New Cryoprobe for Transbronchial Cryobiopsy: A Randomized, Controlled in vivo Animal Study.

BACKGROUND: Forceps biopsy (FB) is still the most popular procedure for the bronchoscopic sampling of lung tissue. However, it has limitations like inadequate sample size and crush artifacts. Cryobiopsy (CB) has been introduced to obtain bronchoscopic biopsies with improved diagnostic yield compared to FB. Limitations of CB are the need to retract the cryoprobe en bloc with bronchoscope because samples are larger than the working channel and the variations of the freezing power of the reusable CB (rCB). Therefore, 3 new disposable cryoprobes (dCB) have been developed with different outer diameters: 1.1 mm (CB11-S) that can be retracted through the working channel of the bronchoscope, 1.7 mm (CB17) and 2.4 mm (CB24n), respectively. OBJECTIVES: The aim was to evaluate the new cryoprobes with regard to feasibility, specimen area, specimen quality and complications. METHODS: We compared biopsy samples of the new probes with those obtained by FB and by rCB in an in vivo (porcine) model. A flexible bronchoscope was used to perform biopsy at 4 different locations at the upper and lower lobes of the right and left lung, respectively. The biopsies were taken under fluoroscopic control. The biopsy tool and activation times were allocated randomly. Altogether 204 biopsy procedures were performed. RESULTS: The sample quality of the dCB was superior to that of FB (all p < 0.05) and not significantly different to the rCB sample quality. Mean specimen sample area of all CB was significantly larger compared to FB (p < 0.05). The sample area of the small cryoprobe (CB11-S) was significantly smaller compared to the other CB probes (p < 0.05). No severe bleedings occurred. Pneumothoraces were detected in 3 of the 7 pigs. CONCLUSION: We conclude that CB with the new single-use instruments are feasible and represent a viable option to improve the diagnostic accuracy of histopathological evaluation compared to FB.

Risk assessment of neuromuscular stimulation by energy-based transurethral resection devices: an ex vivo test standard.

BACKGROUND: During transurethral resection of bladder tumours (TURB), radio-frequency (RF) currents can lead to adverse neuromuscular stimulation (NMS). Here we present a novel ex vivo method to determine the risk of RF generators and their bipolar TURB modes to cause NMS. We aimed to develop an experimental platform for safety evaluation of new RF generators and their modes with a newly established test standard, suitable for replacement or reduction of animal testing. METHODS: We tested four contemporary RF generators with their bipolar modes for TURB in saline. A two-stage ex vivo approach was pursued: First, we recorded voltages at possible positions of the obturator nerve behind a porcine bladder wall in a TURB model using 18 RF applications per generator. Second, these voltage records were used as stimuli to evoke nerve compound action potentials (CAPs) in isolated porcine axillary nerves. The NMS potential was defined as the ratio between the observed area under the CAPs and the theoretical CAP area at maximum response and a firing rate of 250 Hz, which would reliably induce tetanic muscle responses in most human subjects. The measurement protocol was tailored to optimise reproducibility of the obtained NMS potentials and longevity of the nerve specimens. RESULTS: As prerequisite for the clinical translation of our results, the robustness of our test method and reproducibility of the NMS potential are demonstrated with an excellent correlation (r = 0.93) between two sets of identical stimuli (n = 72 each) obtained from 16 nerve segments with similar diameters (4.2 ± 0.37 mm) in the nerve model. The RF generators differed significantly (p < 0.0001) regarding NMS potential (medians: 0-3%). CONCLUSIONS: Our test method is suitable for quantifying the NMS potential of different electrosurgical systems ex vivo with high selectivity at a reasonable degree of standardization and with justifiable effort. Our results suggest that the clinical incidence of NMS is considerably influenced by the type of RF generator. Future generations of RF generators take advantage from the proposed test standard through higher safety and less animal testing. Health professionals and treated patients will benefit most from improved RF surgery using generators with a low NMS risk.

Safety and effectiveness of a novel generator algorithm for bipolar vessel sealing: a randomised controlled chronic animal study.

BACKGROUND: Electrosurgical vessel sealers are gradually replacing conventional techniques such as ligation and clipping. Algorithms that control electrosurgical units (ESU), known as modes, are important for applications in different surgical disciplines. This chronic porcine animal study aimed to evaluate the safety and effectiveness of the novel thermoSEAL electrosurgical vessel sealing mode (TSM). The BiClamp® mode (BCM) of the renowned VIO® 300 D ESU served as control. BCM has been widely available since 2002 and has since been successfully used in many surgical disciplines. The TSM, for the novel VIO® 3 ESU, was developed to reduce sealing time and/or thermal lateral spread adjacent to the seal while maintaining clinical success rates. The primary aim of this study was to investigate the long-term and intraoperative seal quality of TSM. METHODS: The BiCision® device was used for vessel sealing with TSM and BCM in ten German Landrace pigs which underwent splenectomy and unilateral nephrectomy during the first intervention of the study. The seals were cut with the BiCision® knife. Ninety-nine arteries, veins and vascular bundles were chronically sealed for 5 or 21 days. Thereafter, during the second and terminal intervention of the study, 97 additional arteries and veins were sealed. The carotid arteries were used for histological evaluation of thermal spread. RESULTS: After each survival period, no long-term complications occurred with either mode. The intraoperative seal failure rates, i.e. vessel leaking or residual blood flow after the first sealing activation, were 2% with TSM versus 6% with BCM (p = 0.28). The sealing time was significantly shorter with TSM (3.5 ± 0.69 s vs. 7.3 ± 1.3 s, p < 0.0001). The thermal spread and burst pressure of arteries sealed with both modes were similar (p = 0.18 and p = 0.61) and corresponded to the histological evaluation. The measured tissue sticking parameter was rare with both modes (p = 0.33). Tissue charring did not occur. Regarding the cut quality, 97% of the seals were severed in the first and 3% in the second attempt (both with TSM and BCM). CONCLUSIONS: The novel TSM seals blood vessels twice as fast as the BCM while maintaining excellent tissue effect and clinical success rates. TRIAL REGISTRATION: Not applicable.

Gastric mucosal devitalization is safe and effective in reducing body weight and visceral adiposity in a porcine model.

BACKGROUND AND AIMS: The early improvement in metabolic profile after sleeve gastrectomy (SG) indicates that the significant benefits of metabolic surgery are gastric in origin. We have previously demonstrated that devitalization of the gastric mucosa (without a reduction in gastric volume) in metabolically disturbed obese rats results in an improvement of obesity and its associated comorbidities. The aims of this study were to assess the technical feasibility, efficacy, and safety of gastric mucosal devitalization (GMD) in a large animal (porcine) model. METHODS: A 3-arm (GMD versus SG versus sham [SH]) prospective randomized controlled trial with an 8-week follow-up period was performed. The primary endpoint was relative weight loss. Secondary endpoints were absolute body weight, abdominal visceral adiposity, abdominal subcutaneous adiposity, organ lipid content, and serum ghrelin level. RESULTS: GMD resulted in a significant relative weight loss of 36% over SH at 8 weeks (P < .05). There was no significant difference in relative weight loss between GMD and SG at 4 weeks; however, SG resulted in a 29% superior relative weight loss at 8 weeks (P < .05). With regard to visceral adiposity, there was a significant benefit of GMD over SH at 8 weeks. Despite differences in relative weight loss, there was no significant difference in visceral adiposity between SG and GMD at 8 weeks. Significant improvements in GMD over SH were noted with regard to skeletal and heart muscle lipid content. GMD pigs at 8 weeks demonstrated regeneration of the gastric mucosa without ulceration or significant scarring. Despite mucosal regeneration, the abundance of serum ghrelin was significantly lower in the GMD cohort compared with the SG and SH cohorts. CONCLUSIONS: GMD was technically feasible and resulted in relative weight loss and an improvement in visceral adiposity. The benefits noted were out of proportion to what would be expected with weight loss alone.

Evaluation of a novel electrosurgical sealing mode in an ex vivo and in vivo porcine model.

BACKGROUND: Bipolar vessel sealing has been successfully introduced in a variety of procedures like prostatectomy, hysterectomy, and nephrectomy. In this study, we evaluated a new sealing mode-the thermoSEAL® mode (TSM)-operated with the VIO3 generator in an ex vivo and in vivo animal study and compared the results with the commercially available BiClamp mode (BCM), operated with the VIO300D generator. Two different instruments were used in combination with both modes, BiCision® and BiClamp® 201T (Erbe Elektromedizin GmbH). METHODS: In the ex vivo experiment, the sealing of renal arteries was evaluated using both instruments and modes. For the in vivo study, different types of arteries and veins were sealed using both modes and instruments in a side-by-side comparison for acute complications in a total of four animals. RESULTS: Mean burst pressure was in all cases significantly above 360 mmHg (p < 0.001). Sealing time during the ex vivo setting was significantly shorter for TSM compared to BCM: BiCision® (3.7 ± 0.4 vs. 7.1 ± 0.3 s; p < 0.0001); BiClamp® 201T (3.9 ± 0.3 vs. 5.1 ± 1.1 s; p < 0.0015). Lateral thermal damage was more pronounced for BCM: BiCision® (TSM 1.4 ± 0.3 mm vs. BCM 1.9 ± 0.2 mm; p < 0.0001); BiClamp® 201T (TSM 1.9 ± 0.6 mm vs. BCM 3.1 ± 0.6 mm; p < 0.0001). The sealing time during the in vivo study was significantly shorter for TSM in combination with BiCision® for arteries [TSM 3.0 ± 0.7 s vs. BCM 6.5 ± 1.3 s, (p < 0.0001) and veins 3.2 ± 1.1 vs. 5.8 ± 1.8 s, (p < 0.0001)]. No significant differences were seen for the two modes used with BiClamp® 201T [artery: TSM 3.3 ± 0.7 s vs. BCM 3.4 ± 0.9 s, (p = 0.891)]. High sealing rates for arteries (100%) and veins (>90%) were noted for both instruments and modes. CONCLUSIONS: While both modes used with two different instruments reveal high safety characterized by a high burst pressure, low thermal damage (ex vivo) zones, and high sealing rates (in vivo), the thermoSEAL® mode convinces by its fast sealing speed probably helping to reduce operation time.

A prospective randomized experimental study to investigate the peritoneal adhesion formation after waterjet injection and argon plasma coagulation (HybridAPC) in a rat model.

BACKGROUND: This prospective, randomized, controlled, single-blinded study investigates the peritoneal adhesion formation of HybridAPC (waterjet elevation of the peritoneum with subsequent argon plasma coagulation) versus only waterjet (elevation with the same instrument, but without subsequent argon plasma coagulation) in a rat model (24 female Wistar rats). MATERIALS AND METHODS: Bilateral lesions were created on the abdominal wall with HybridAPC on one sidewall and waterjet elevation on the other sidewall of the peritoneum in a standard fashion. After 10 days, the rats were euthanized to evaluate the peritoneal trauma sites. MAIN OUTCOME MEASURE(S): Adhesion incidence, quantity, and quality were scored 10 days postoperatively and studied histopathologically. RESULT(S): Incidence of adhesion formation was 2.3% for HybridAPC; no adhesions occurred for peritoneal elevation with saline (p = 1.00). Histologic evaluation revealed no acute inflammation in both groups. An overall moderate degree of granulation tissue formation and myonecrosis was observed in the HybridAPC group, whereas no chronic inflammation and myonecrosis occurred after elevation without thermal ablation (p < 0.0001). CONCLUSION(S): This study investigates the effect of waterjet elevation of the peritoneum with and without subsequent thermal ablation on adhesion formation in a rat model for the first time. Peritoneal waterjet elevation with saline does not provide any risk of adhesion formation. Thermal coagulation with APC after waterjet elevation of the peritoneum creates advantageous peritoneal conditions due to a permanent moist tissue surface and the cooling effect of the injected solution, resulting in no significant difference in adhesion formation compared to peritoneal elevation without thermal ablation. HybridAPC can thus be regarded as a beneficial coagulation method with only minor adhesion formation due to positive tissue effects of the combined waterjet.

A randomised trial of endoscopic submucosal dissection versus endoscopic mucosal resection for early Barrett's neoplasia.

BACKGROUND: For endoscopic resection of early GI neoplasia, endoscopic submucosal dissection (ESD) achieves higher rates of complete resection (R0) than endoscopic mucosal resection (EMR). However, ESD is technically more difficult and evidence from randomised trial is missing. OBJECTIVE: We compared the efficacy and safety of ESD and EMR in patients with neoplastic Barrett's oesophagus (BO). DESIGN: BO patients with a focal lesion of high-grade intraepithelial neoplasia (HGIN) or early adenocarcinoma (EAC) ≤3 cm were randomised to either ESD or EMR. Primary outcome was R0 resection; secondary outcomes were complete remission from neoplasia, recurrences and adverse events (AEs). RESULTS: There were no significant differences in patient and lesion characteristics between the groups randomised to ESD (n=20) or EMR (n=20). Histology of the resected specimen showed HGIN or EAC in all but six cases. Although R0 resection defined as margins free of HGIN/EAC was achieved more frequently with ESD (10/17 vs 2/17, p=0.01), there was no difference in complete remission from neoplasia at 3 months (ESD 15/16 vs EMR 16/17, p=1.0). During a mean follow-up period of 23.1±6.4 months, recurrent EAC was observed in one case in the ESD group. Elective surgery was performed in four and three cases after ESD and EMR, respectively (p=1.0). Two severe AEs were recorded for ESD and none for EMR (p=0.49). CONCLUSIONS: In terms of need for surgery, neoplasia remission and recurrence, ESD and EMR are both highly effective for endoscopic resection of early BO neoplasia. ESD achieves a higher R0 resection rate, but for most BO patients this bears little clinical relevance. ESD is, however, more time consuming and may cause severe AE. TRIAL REGISTRATION NUMBER: NCT1871636.

Standard needle versus needleless injection modality: animal study on different fluids for submucosal elevation.

BACKGROUND AND AIMS: Submucosal injection is currently used in GI endoscopy to reduce resection risks and to perform submucosal dissection; it is usually performed via an injection needle or a needleless device. The aim of the study was to compare 2 submucosal injection modalities (needle-assisted vs needleless) by using substances with different viscosities. METHODS: Needle and needleless injections were compared by assessing the efficacy of tissue elevation with 5 different substances in an ex vivo porcine model. The height of the submucosal elevation was measured 0(t0), 10(t1), and 30 minutes after injection (t2). Viscosity of the solution was also measured. RESULTS: For both stomach and rectum, at t0, t1, and t2 no difference in the height of the elevation was found between the needle and needleless technique, irrespective of the substance. Tissue elevation in the stomach was similar between the 2 techniques at t0 (9.9 ± 1.58 vs 9.4 ± 1.3 mm, P = .3), t1 (7.2 ± 1.56 vs 6.9 ± 1.4 mm, P =. 26), and t2 (6 ± 1.6 vs 5.5 ± 1.3 mm, P = .18). No difference was found in the rectum at t1 and t2, whereas a slightly higher elevation with the needle-assisted technique was observed at t0 (t0: 12.4 ± 1.3 vs 11.2 ± 1.6 mm, P = .003; t1: 8.7 ± 1.3 vs 8.3 ± 1.5 mm; P = .32; t2: 7.0 ± 1.4 vs 7.2 ± .76 mm; P = .75). When comparing the substances with normal saline solution, more viscous solutions showed a significantly higher elevation at t0, t1, and t2 irrespective of the injection modalities and the location. CONCLUSIONS: No differences were found in the height of submucosal injection or in the persistence of such elevation when comparing needleless with needle-assisted injection, with the only minor exception of the initial elevation in the rectum, which does not appear to be clinically relevant. Viscous solutions resulted in higher and more persistent elevations as compared with normal saline solution.

In silico evaluation of geometry variations with respect to the thermal spread during coagulation of egg white using bipolar vessel sealing instruments.

BACKGROUND: Bipolar vessel sealing is an efficient electrosurgical procedure for the occlusion of blood vessels particularly during minimally invasive surgery. Reliable knowledge of the thermal spread is crucial for a safe application of bipolar vessel sealing instruments when operating close to thermo-sensitive structures, such as nerves. The evolution of the thermal spread over time and space depends on a variety of parameters, such as the biological tissue, the energy applied to the tissue, and the geometry of the vessel sealing instrument. Mathematical modeling has proven useful for the prediction of the thermal spread. It is, thus, a promising tool for the systematic analysis of the influence of geometrical changes on the thermal spread. RESULTS: We present an experimentally validated in silico study to evaluate the impact of geometry variations on the progression of chicken egg white coagulation and the final shape of coagulated egg white as an approximation of the temporal and spatial evolution of the thermal spread during bipolar vessel sealing. Egg white has similar thermal and electrical properties to human tissue, with the advantage being that the spatial and temporal evolution of the thermal spread can be visually gauged. The simulations were performed using a mathematical model based on the finite element analysis of chicken egg white. The progression of egg white coagulation was predicted for two different peak voltages and various electrode geometries. Starting with two planar electrodes, one electrode was gradually changed to adopt a wedge shape. These changes to the geometry showed a distinct influence on the progression of egg white coagulation in the simulations. The predictions were successfully validated using an experimental setup with two different electrodes representing the extreme geometries. DISCUSSION: The predicted spatial temperature distributions were experimentally validated for two geometries. Our simulation study shows that the geometry has a pronounced influence on the thermal spread and, thus, is a suitable parameter to reduce thermal damage. The in silico optimization of instrument designs is a suitable tool to accelerate the development of new vessel sealing instruments, with only a few promising designs having to be tested as prototypes.

A Prospective Randomized Experimental Study to Investigate the Eradication Rate of Endometriosis after Surgical Resection versus Aerosol Plasma Coagulation in a Rat Model.

PURPOSE: To investigate the eradication rate of endometriosis after surgical resection (SR) vs. thermal ablation with aerosol plasma coagulation (AePC) in a rat model. METHODS: In this prospective, randomized, controlled, single-blinded animal study endometriosis was induced on the abdominal wall of 34 female Wistar rats. After 14 days endometriosis was either removed by SR or ablated by AePC. 14 days later the rats were euthanized to evaluate the eradication rate histopathologically. Intervention times were recorded. RESULTS: Eradication rate of endometriosis after 14 days did not significantly differ between AePC and SR (p=0.22). Intervention time per endometrial lesion was 22.1 s for AePC and 51.8 s for SR (p<0.0001). CONCLUSIONS: This study compares the eradication rate of the new aerosol plasma coagulation device versus standard surgical resection of endometriosis in a rat model. Despite being a thermal method, AePC showed equality towards SR regarding eradication rate but with significantly shorter intervention time.

A New Tool for Transbronchial Cryobiopsies in the Lung: An Experimental Feasibility ex vivo Study.

BACKGROUND: Transbronchial cryobiopsy (TBCB) is a minimally invasive procedure to establish a diagnosis of interstitial lung disease though with the disadvantage that samples have to be extracted together with the bronchoscope. OBJECTIVES: The aim of the present study was to evaluate the feasibility of a new cryoprobe with which biopsy samples can be obtained through the working channel of the flexible bronchoscope. METHODS: The feasibility of obtaining transbronchial specimens with TBCB was tested and the technique was compared to transbronchial forceps biopsy (TBFB) in a prospectively randomized ex vivo animal study using a standard flexible bronchoscopy technique. The rate of successful biopsies and the duration of the sampling procedure were recorded for both methods. Size and quality of the biopsies were histologically evaluated and measured. RESULTS: Biopsy samples could be obtained in 93.3% of TBCB and in 79.0% of TBFB procedures (p = 0.182). Sampling procedure time did not differ in any clinically relevant manner between the two methods. The mean specimen area of TBCB samples was significantly higher compared to that of TBFB samples (8.08 ± 5.80 vs. 2.61 ± 2.14 mm2; p < 0.0001). TBCB specimens showed less artifacts and a significantly higher percentage of alveolar tissue (53.57 vs. 25.42%; p = 0.0285) than TBFB specimens. CONCLUSIONS: It is feasible to retrieve TBCB samples of good quality and size with the new mini cryoprobe through the working channel of the bronchoscope, while the bronchoscope remains within the central airways throughout the whole procedure. Further studies are necessary to evaluate the safety and efficacy in an in vivo setting.

Bipolar vessel sealing: instrument contamination and wear have little effect on seal quality and success in a porcine in vitro model.

PURPOSE: The aim of this study is to systematically investigate under standardized experimental conditions the effects of instrument contamination and wear on the quality of bipolar vessel sealing (BVS) achieved using a reusable instrument. METHODS: The study was designed as a prospective, randomized, and controlled in vitro study and conducted in an academic research environment. Reusable bipolar coagulation forceps (BiClamp® 200 C, ERBE Elektromedizin) were used to apply sealing pressures of 300-1,100 mN/mm(2) to 239 renal arteries from commercially slaughtered female pigs (Swabian-Hall Swine). Forceps jaws were coated with porcine blood, blood and collagen, or blood, collagen, and fat to simulate instrument contamination with biological material during surgery. Clinical wear was mimicked by sandpaper abrasion. The main outcome measures were seal success (resistance to 250 mmHg intraluminal pressure for 2 min) and seal stability (burst pressure). RESULTS: Sealing pressure had a significant impact, with 800 mN/mm(2) producing the best sealing results. Seal success increased with total energy applied to the tissue, a higher maximum temperature, and longer coagulation as indicated by desiccation time. Experimental contamination had no significant impact on seal success and only a limited effect on seal stability. Similarly, abrasive wear also had no significant effect on either seal quality or seal strength. CONCLUSIONS: The impact of bipolar forceps contamination and wear on seal success and quality was negligible in our in vitro model. To achieve high-quality seals, it is essential to use adequate sealing pressures. Our findings could have direct implications for the design and clinical handling of BVS instruments.

A Prospective Experimental Study to Investigate the Peritoneal Adhesion Formation of Argon Plasma Coagulation (APC) Versus a Novel Aerosol Plasma in a Rat Model.

BACKGROUND: This is a prospective, randomized, controlled, single-blinded study to investigate peritoneal adhesion formation of standard argon plasma coagulation (APC) versus aerosol plasma coagulation in a rat model. METHODS: Bilateral lesions were created on the abdominal wall of 16 female Wistar rats with standard and aerosol plasma coagulation APC energy in a standard fashion. After 10 days, the rats were killed humanely to evaluate the peritoneal trauma sites. Adhesion incidence, quantity, and quality were scored 10 days postoperatively and studied histopathologically. RESULTS: Average energy intake was 97.7 ± 3.1 J for APC and 93.8 ± 4.2 J for aerosol plasma coagulation. Incidence of adhesion formation was 74.2% for standard APC and 16.1% for aerosol plasma coagulation (P < .0001). Standard APC mainly results in dense adhesions. Histological evaluation revealed no significant difference with regard to the average depth of lesions created by APC and aerosol plasma coagulation (P = 0.21) at day 10; both groups showed an identical morphology of necrosis and granulation tissue formation. CONCLUSIONS: This study compares adhesion formation of standard APC versus aerosol plasma coagulation in a rat model. Standard APC produced significantly more adhesions. Aerosol plasma coagulation creates fewer adhesions, which are of lower grade, which seems to be achieved mainly by improved peritoneal conditioning in this animal model.

Application of Deep Learning for Real-Time Ablation Zone Measurement in Ultrasound Imaging.

BACKGROUND: The accurate delineation of ablation zones (AZs) is crucial for assessing radiofrequency ablation (RFA) therapy's efficacy. Manual measurement, the current standard, is subject to variability and potential inaccuracies. AIM: This study aims to assess the effectiveness of Artificial Intelligence (AI) in automating AZ measurements in ultrasound images and compare its accuracy with manual measurements in ultrasound images. METHODS: An in vitro study was conducted using chicken breast and liver samples subjected to bipolar RFA. Ultrasound images were captured every 15 s, with the AI model Mask2Former trained for AZ segmentation. The measurements were compared across all methods, focusing on short-axis (SA) metrics. RESULTS: We performed 308 RFA procedures, generating 7275 ultrasound images across liver and chicken breast tissues. Manual and AI measurement comparisons for ablation zone diameters revealed no significant differences, with correlation coefficients exceeding 0.96 in both tissues (p < 0.001). Bland-Altman plots and a Deming regression analysis demonstrated a very close alignment between AI predictions and manual measurements, with the average difference between the two methods being -0.259 and -0.243 mm, for bovine liver and chicken breast tissue, respectively. CONCLUSION: The study validates the Mask2Former model as a promising tool for automating AZ measurement in RFA research, offering a significant step towards reducing manual measurement variability.