Fast and efficient extraction and determination of nonsteroidal anti-inflammatory drugs using poly(8-hydroxyquinoline)-coated magnetic graphene oxide nanocomposite prior to capillary electrophoresis analysis in wastewater, breast milk, and urine samples.

In this study, magnetic graphene oxide coated with poly(8-hydroxyquinoline) was successfully synthesized, characterized, and utilized as a novel sorbent for the ultrasonic-assisted dispersive magnetic solid-phase extraction of naproxen and ibuprofen. These analytes served as representative analytes for two nonsteroidal anti-inflammatory drugs in various real samples. Characterization techniques, such as IR, X-ray powder diffraction, field emission scanning electron microscopy, energy-dispersive X-ray-mapping, and Brunauer-Emmett-Teller (BET), were used to confirm the correctness synthesis and preparation of the nanocomposites. Effective parameters on the extraction efficiency were investigated to maximize the analytical performance of the developed method. The dynamic range (1-1000 µg L-1), coefficients of determination (R2 ≥ 0.997), the limits of detection (0.3-1.0 µg L-1), and limit of quantification (1.0-3.0 µg L-1), intra-day and inter-day precisions (3.5%-7.2%) were achieved. The method validation results showed extraction recovery ranging from 80.4% to 96.0% and preconcentration factors ranging from 137 to 140.

Dispersive magnetic solid phase extraction of triazole fungicides based on polybenzidine/magnetic nanoparticles in environmental samples.

A polybenzidine-modified Fe3O4@SiO2 nanocomposite was successfully synthesized through a chemical oxidation method and employed as a novel sorbent in dispersive magnetic solid phase extraction (DMSPE) for the preconcentration and determination of three triazole fungicides (TFs), namely diniconazole, tebuconazole, and triticonazole in river water, rice paddy soil, and grape samples. The synthesis method involved a polybenzidine self-assembly coating on Fe3O4@SiO2 magnetic composite. Characterization techniques such as FT-IR, XRD, FESEM, EDX, and VSM were used to confirm the correctness of the synthesized nano-sorbent. The target TFs were determined in actual samples using the synthesized nanocomposite sorbent in combination with gas chromatography-flame ionization detection (FID). Several variables were carefully optimized , including the sample pH, sorbent dosage, extraction time, ionic strength, and desorption condition (solvent type, volume, and time). Under the optimized experimental conditions, the method exhibited linearity in the concentration range 5-1000 ng mL-1 for triticonazole and 2-1000 ng mL-1 for diniconazole and tebuconazole. The limits of detection (LOD) for the three TFs were in the range 0.6-1.5 ng mL-1. The method demonstrated acceptable precision with intra-day and inter-day relative standard deviation (RSD) values of less than 6.5%. The enrichment factors ranged from 248 to 254. Finally, the method applicability was evaluated by determining TFs in river water, rice paddy soil, and grape samples with recoveries in the range 90.5-106, indicating that the matrix effect was negligible in the proposed DMSPE procedure.

Gelatin microsphere coated Fe3O4@graphene quantum dots nanoparticles as a novel magnetic sorbent for ultrasound-assisted dispersive magnetic solid-phase extraction of tricyclic antidepressants in biological samples.

Gelatin microsphere-coated Fe3O4@graphene quantum dots (Fe3O4@GQD@GM) were designed and synthesized as a novel sorbent via ultrasonic-assisted dispersive magnetic solid-phase extraction (UA-DMSPE) method. The synthesized sorbent was identified and confirmed by FT-IR, XRD, VSM, and SEM techniques. UA-DMSPE was combined with corona discharge ion mobility spectrometry for trace determination of desipramine, sertraline, and citalopram. Effective parameters were considered and optimized. The proposed method, under optimal conditions, showed excellent linearity in different concentration ranges (2-700 ng mL-1, R2 > 0.995), repeatability (RSD < 5.1%), good sensitivity (LODs in the range 0.6-1.5 ng mL-1), high preconcentration factor (PF = 207-218), and acceptable relative recoveries (93.5-101.8%). Eventually, this method was used to determine tricyclic antidepressants in various biological samples. Schematic presentation of the microextraction and monitoring of TCAs by ultrasonic-assisted dispersive magnetic solid phase microextraction-ion mobility spectrometry producer.

Electrospun terpolymeric nanofiber membrane for micro solid-phase extraction of diazinon and chlorpyrifos from aqueous samples.

The present study deals with the synthesis and electrospining of a new terpolymer nanofiber in order to determine the amount of diazinon and chlorpyrifos in water and fruit juice samples. The synthesized terpolymer and the prepared nanofiber were characterized using 1 H NMR spectroscopy, FTIR spectroscopy, scanning electron microscopy, and gel permeation chromatography. The performance of terpolymer nanofiber, prepared as a sorbent for micro solid phase extraction was investigated for the extraction of diazinon and chlorpyrifos from aquaeous media. Then, the target analytes were desorbed from the coating with an organic solvent and analyzed by gas chromatography with flame ionization detector. Extraction efficiencies were significant (>90%) under the optimum condition. The proposed method also demonstrated good linear dynamic ranges for diazinon and chlorpyrifos (3-250 and 5-200 µg/L), and low limit of detections (0.5 and 0.7 µg/L) respectively. Moreover, under optimum condition for extraction of diazinon and chlorpyrifos, square of correlation coefficients (R2 ) of 0.9978 and 0.9953 and relative standard deviations of 4.6 and 5.1% were achieved, respectively. The recoveries for diazinon and chlorpyrifos were in the range of 85-97%.

A mesoporous nanosorbent composed of silica, graphene, and palladium (II) for ultrasound-assisted dispersive solid-phase extraction of organophosphorus pesticides prior to their quantitation by ion mobility spectrometry.

A new ultrasonic-assisted dispersive solid-phase extraction method using mesoporous nanosorbent composed of silica, graphene, and palladium (II) (M S/G@-SH@Pd (II)), coupled with corona discharge ion mobility spectrometry, was developed for trace determination of organophosphorus pesticides. Initially, the M S/G@-SH@Pd (II) nanosorbent was synthesized and characterized. Then, the nanosorbent was used for the sorption and extraction of organophosphorus pesticides. Under the optimized conditions (pH = 7.0, 15 mg of sorbent, 3 min extraction time, ethanol as desorption agent, 3 min centrifuge time), the proposed technique provided good linearity (R2 > 0.994), repeatability (RSD < 4.6%), low limits of detection (0.15-0.30 ng mL-1), excellent preconcentration factor (PF = 472-478), and high recoveries (93-94%). The method was applied to the determination of organophosphorus pesticides in real water samples. The sorbent was reused in 5 cycles without any considerable loss of activity. Graphical abstract Schematic presentation of design and synthesis of mesoporous nanosorbent composed of silica, graphene, and palladium (II) for ultrasound-assisted dispersive solid-phase extraction of organophosphorus pesticides prior to their quantitation by ion mobility spectrometry.

Development and application of SBA-15 assisted electromembrane extraction followed by corona discharge ion mobility spectrometry for the determination of Thiabendazole in fruit juice samples.

A new sample preparation method based on SBA-15 assisted electromembrane extraction coupled with corona discharge ion mobility spectrometer was developed for the determination of Thiabendazole as a model basic pesticide in fruit juice samples. The addition of SBA-15 in the supported liquid membrane in electromembrane extraction system not only can lead to enhancement of the effective surface area, but also introducing the negatively charged silanol groups into supported liquid membrane might improve migration of positively charged analytes toward the supported liquid membrane and finally into the acceptor solution. To investigate the effect of the presence of SBA-15 in the supported liquid membrane on the extraction efficiency, a comparative study was carried out between the conventional electromembrane extraction and SBA-15/electromembrane extraction methods. Under the optimized conditions, SBA-15/electromembrane extraction method showed higher extraction efficiencies in comparison with conventional electromembrane extraction method. SBA-15/electromembrane extraction method exhibited a low limit of detection (0.9 ng/mL), high preconcentration factor (167) and high recovery (83%). Finally, the applicability of SBA-15/electromembrane extraction method was studied by the extraction and determination of Thiabendazole as a model basic pesticide in fruit juice samples.

Ultrasound assisted dispersive solid phase extraction of triazole fungicides by using an N-heterocyclic carbene copper complex supported on ionic liquid-modified graphene oxide as a sorbent.

An ultrasound-assisted method is described for dispersive solid phase extraction of trace levels of triazole fungicides. A sorbent was prepared from an N-heterocyclic carbene copper complex that was supported on ionic liquid-modified graphene oxide. The sorbent was characterized by scanning electron microscopy, transmission electron microscopy, Raman and FT-IR spectroscopy, energy-dispersive X-ray spectroscopy and elemental mapping. The capability of sorption and extraction is mainly based on complexation with Cu (I) ions. The variables affecting extraction were optimized. Following desorption with ethanol, the fungicides were quantified by corona discharge ion mobility spectrometry. Under optimized conditions (solution pH value: 7.0; amount of sorbent: 10 mg; extraction time: 3 min; desorption agent: ethanol), the technique provides good linearity (>0.994), repeatability (RSD < 4.1%), low limits of detection (0.18 ng.mL-1), excellent preconcentration factors (468-476) and high recoveries from spiked environmental water samples (92-94%). The sorbent can be reused over five cycles without significant loss of its activity. Graphical abstract Schematic presentation of design and synthesis of the N-heterocyclic carbene copper complex supported on ionic liquid-modified graphene oxide as a sorbent for triazole fungicides and its application in ultrasound-assisted dispersive solid phase extraction with ion mobility spectrometric detection.

Evaluation of the synergistic effect with amino acids for enantioseparation of basic drugs using capillary electrophoresis.

The synergistic effect of two acidic amino acids, aspartic and glutamic acid, on the electrophoretic enantioseparation of four basic drugs was evaluated in the BGE containing a CD and at different pHs. Chlorpheniramine, hydroxyzine, propranolol and tramadol were used as the basic model drugs. However, no enantioseparations were achieved with a BGE containing sole amino acid, but the combined use of an acidic amino acid and a CD showed improved enantioseparations (synergistic effect) compared with the single CD system. The results demonstrated that at optimized pH, the electrostatic interactions of the anionic amino acids with the positively charged basic drugs could result in a decrease of the analyte migration velocity and it consequently improved the enantioseparation. The effective parameters such as the amino acid and chiral selector type and concentration, buffer pH, applied voltage, and capillary temperature were optimized. Favorable enantiomeric resolution and migration times of the model drugs were achieved with a 100 mM phosphate buffer solution (pH 3.0) containing 5.0 mM HP-α-CD/HP-ß-CD and 20 mM aspartic acid with an 18 kV applied voltage at 25°C. 1 H NMR experiments were also carried out in a mixture of an analyte and CD in the absence and presence of aspartic acid. The NMR results were consistent with the results obtained by CE which showed the synergistic effect of amino acid.

Simultaneous chiral separation of tramadol and methadone in tablets, human urine, and plasma by capillary electrophoresis using maltodextrin as the chiral selector.

The stereoselective analysis and separation of racemic drugs play an important role in pharmaceutical industry to eliminate the unwanted isomer and find the right therapeutic control for the patient. Present study suggests a maltodextrin-modified capillary electrophoresis method for a single-run chiral separation of two closely similar opiate pain relief drugs: tramadol (TRA) and methadone (MET). The best separation method possible for the both enantiomers was achieved on an uncoated fused-silica capillary at 25°C using 100 mM phosphate buffer (pH 8.0) containing 20% (w v-1 ) maltodextrin with dextrose equivalent of 4-7 and an applied voltage of 16 kV. Under optimal conditions, the baseline resolution of TRA and MET enantiomers was obtained in less than 12 minutes. The relative standard deviations (n = 3) of 20 µg mL-1 TRA and MET were 2.28% and 3.77%, respectively. The detection limits were found to be 2 µg mL-1 for TRA and 1.5 µg mL-1 for MET. This method was successfully applied to the measurement of drugs concentration in their tablets, urine, and plasma samples.

Surfactant-assisted electromembrane extraction combined with cyclodextrin-modified capillary electrophoresis for the separation and quantification of Tranylcypromine enantiomers in biological samples.

Surfactant-assisted electromembrane extraction coupled with cyclodextrin-modified capillary electrophoresis was developed for the separation and determination of Tranylcypromine enantiomers in biological samples. This combination would provide a new strategy for selective and sensitive determination of target analytes. The addition of surfactant in the donor solution improved the analyte transport into the lumen of hollow fiber that resulted in an enhancement in the analytes migration into acceptor solution. Optimization of the variables, affecting proposed method, was carried out and best results were achieved with a 175 V potential as driving force of the electromembrane extraction, 2-nitrophenyloctylether as the supported liquid membrane, donor solution containing 0.2 mM Triton X-100 with pH 3 and 0.1 M HCl for acceptor solution. Then, the extract was analyzed using cyclodextrin-modified capillary electrophoresis method for separation of Tranylcypromine enantiomers. The best results were obtained with a phosphate running buffer (100 mM, pH 2.0) containing 7% w/v hydroxypropyl-α-cyclodextrin. Under the optimum conditions, a low limit of detection (3.03 ng/mL), good linearity (R2  > 0.9953), and relative standard deviations below 4.0% (n = 5) were obtained. Finally, this procedure was applied to determine the concentration of Tranylcypromine enantiomers in urine samples with satisfactory results.

All-in-one solid-phase microextraction: Development of a selective solid-phase microextraction fiber assembly for the simultaneous and efficient extraction of analytes with different polarities.

In the present work, for the first time, an all-in-one solid-phase microextraction technique was developed for the simultaneous and efficient extraction of analytes within a vast polarity range. A novel fiber assembly composed of two different steel components each coated with different coatings (polydimethylsiloxane and polyethylene glycol) in terms of polarity by sol-gel technology was employed for the extraction of model compounds of different polarity in a single run followed by gas chromatography with mass spectrometry. Effective parameters in the extraction step and gas chromatography with mass spectrometry analysis were optimized for all model compounds. The detection limits of the developed method for model compounds were below 0.2 ng/L. The repeatability and reproducibility of the proposed method, explained by relative standard deviation, varied between 7.22 and 9.15% and between 7.95 and 14.90 (n = 5), respectively. Results showed that, under random conditions, compared to separate extractions performed by two other differently end-coated components that had not been assembled as the final dual fiber, as two individual fibers; simultaneous, efficient and relatively selective extraction of all model compounds was obtained in a single run by the proposed all-in-one technique. Finally, the optimized procedure was applied to extraction and determination of the model compounds in spiked water samples.

Evaluation of sulfated maltodextrin as a novel anionic chiral selector for the enantioseparation of basic chiral drugs by capillary electrophoresis.

Introducing a new class of chiral selectors is an interesting work and this issue is still one of the hot topics in separation science and chirality. In this study, for the first time, sulfated maltodextrin (MD) was synthesized as a new anionic chiral selector and then it was successfully applied for the enantioseparation of five basic drugs (amlodipine, hydroxyzine, fluoxetine, tolterodine, and tramadol) as model chiral compounds using CE. This chiral selector has two recognition sites: a helical structure and a sulfated group which contribute to three corresponding driving forces; inclusion complexation, electrostatic interaction, and hydrogen binding. Under the optimized condition (buffer solution: 50 mM phosphate (pH 3.0) and 2% w/v sulfated MD; applied voltage: 18 kV; temperature: 20°C), baseline enantioseparation was observed for all mentioned chiral drugs. When instead of sulfated MD neutral MD was used under the same condition, no enantioseparation was observed which means the resolution power of sulfated MD is higher than neutral MD due to the electrostatic interaction between sulfated groups and protonated chiral drugs. Also, the countercurrent mobility of negatively charged MD (sulfated MD) allows more interactions between the chiral selector and chiral drugs and this in turn results in a successful resolution for the enantiomers. Furthermore, a higher concentration of neutral MD (approximately five times) is necessary to achieve the equivalent resolution compared with the negatively charged MD.

Surfactant-assisted electromembrane extraction combined with capillary electrophoresis as a novel technique for the determination of acidic drugs in biological fluids.

In this paper, for the first time, surfactant-assisted electromembrane extraction coupled with capillary electrophoresis with UV detector was introduced for the extraction of acidic drugs from biological fluids. In this technique, in the presence of the nonionic surfactant in the donor phase, tendency of analyte ions into the supported liquid membrane (SLM) was increased. Naproxen and diclofenac were selected as model acidic drugs. In order to obtain the best extraction efficiency, several factors influencing the extraction efficiency were investigated. Optimal extractions were accomplished with 1-octanol as the SLM, 15 Volt dc potential as the driving force, pH 12 in acceptor solution, and 0.2 mmol/L Triton X-100 with pH 7.4 in donor solution. Equilibrium extraction conditions were obtained after 15 min of operation where the whole assembly agitated at 1000 rpm. Under the optimized conditions, preconcentration factors in the range of 176-184 and recoveries in the range of 88-92% were obtained. The applied method offers acceptable linearity with correlation coefficients higher than 0.9992. Limits of detection of 1.51 ng/mL and 2.42 ng/mL were obtained for naproxen and diclofenac, respectively. Finally, the developed method was successfully applied for the determination of naproxen and diclofenac in different matrices including plasma and urine samples.

Maltodextrins as chiral selectors in CE: molecular structure effect of basic chiral compounds on the enantioseparation.

Prediction of chiral separation for a compound using a chiral selector is an interesting and debatable work. For this purpose, in this study 23 chiral basic drugs with different chemical structures were selected as model solutes and the influence of their chemical structures on the enantioseparation in the presence of maltodextrin (MD) as chiral selector was investigated. For chiral separation, a 100-mM phosphate buffer solution (pH 3.0) containing 10% (w/v) MD with dextrose equivalent (DE) of 4-7 as chiral selector at the temperature of 25°C and voltage of 20 kV was used. Under this condition, baseline separation was achieved for nine chiral compounds and partial separation was obtained for another six chiral compounds while no enantioseparation was obtained for the remaining eight compounds. The results showed that the existence of at least two aromatic rings or cycloalkanes and an oxygen or nitrogen atom or -CN group directly bonded to the chiral center are necessary for baseline separation. With the obtained results in this study, chiral separation of a chiral compound can be estimated with MD-modified capillary electrophoresis before analysis. This prediction will minimize the number of preliminary experiments required to resolve enantiomers and will save time and cost.

Application of maltodextrin as chiral selector in capillary electrophoresis for quantification of amlodipine enantiomers in commercial tablets.

Maltodextrin was investigated as a chiral selector in capillary electrophoresis (CE) analysis of amlodipine (AM) enantiomers. For development of a stereoselective CE method, various effective parameters on the enantioseparation were optimized. The best results were achieved on an uncoated fused silica capillary at 20 °C using phosphate buffer (100 mM, pH 4) containing 10% w/v maltodextrin (dextrose equivalent value 4-7). The UV detector was set at 214 nm and a constant voltage of 20 kV was applied. The range of quantitation was 2.5-250 µg/mL (R(2) > 0.999) for both enantiomers. Intra- (n = 5) and interday (n = 3) relative standard deviation (RSD) values were less than 7%. The limits of quantitation and detection were 1.7 µg/mL and 0.52 µg/mL, respectively. Recoveries of R(+) and S(-) enantiomers from tablet matrix were 97.2% and 97.8%, respectively. The method was applied for the quantification of AM enantiomers in commercial tablets. Also, the enantioseparation capability of heparin was evaluated and the results showed that heparin did not have any chiral selector activity in this study.

Electrically assisted liquid-phase microextraction combined with capillary electrophoresis for quantification of propranolol enantiomers in human body fluids.

In this study, electromembrane extraction (EME) combined with cyclodextrin (CD)-modified capillary electrophoresis (CE) was applied for the extraction, separation, and quantification of propranolol (PRO) enantiomers from biological samples. The PRO enantiomers were extracted from aqueous donor solutions, through a supported liquid membrane (SLM) consisting of 2-nitrophenyl octyl ether (NPOE) impregnated on the wall of the hollow fiber, and into a 20-µL acidic aqueous acceptor solution into the lumen of hollow fiber. Important parameters affecting EME efficiency such as extraction voltage, extraction time, pH of the donor and acceptor solutions were optimized using a Box-Behnken design (BBD). Then, under these optimized conditions, the acceptor solution was analyzed using an optimized CD-modified CE. Several types of CD were evaluated and best results were obtained using a fused-silica capillary with ammonium acetate (80 mM, pH 2.5) containing 8 mM hydroxypropyl-ß-CD as a chiral selector, applied voltage of 18 kV, and temperature of 20°C. The relative recoveries were obtained in the range of 78-95%. Finally, the performance of the present method was evaluated for the extraction and determination of PRO enantiomers in real biological samples.

Development of carbon-nanotube-assisted electromembrane extraction in the two-phase mode combined with GC for the determination of basic drugs.

In this work, carbon-nanotube-assisted electromembrane extraction in the two-phase mode combined with GC was developed for the preconcentration and determination of basic drugs in body fluids. The multiwalled carbon nanotubes dispersed in organic solvent are held in the pores of the porous fiber wall by capillary forces and sonification. The membrane with immobilized carbon nanotubes acts as a sorbent and provides an additional pathway for analyte transport. This study demonstrates that the immobilization of carbon nanotubes in the supported liquid membrane is an excellent approach to enhance the performance of the extraction. Optimization of the variables affecting this method was carried out in order to achieve the best extraction efficiency. Optimal extractions were accomplished with octanol as the extraction solvent, 50 V as the driving force and pH 7.4 in the sample solution with the whole assembly agitated at 1000 rpm for 20 min. Under the optimized extraction conditions, the proposed technique provided good linearity (R(2) > 0.9990), repeatability (3.5-3.8%), low LODs (1.5 ng/mL), good preconcentration factors (292-316) and high recoveries (80-87%). Finally, this method was successfully used for the determination of tramadol and methadone in different body fluids including plasma and urine samples.

Facile extraction and determination of organophosphorus pesticides using poly (8-hydroxyquinoline) functionalized magnetic multi-walled carbon nanotubes nanocomposite in water, fruits, and vegetables samples.

This study presents a dispersive micro-solid phase extraction (D-µ-SPE) approach for extracting and determining of two organophosphorus pesticides (OPPs), including diazinon and chlorpyrifos as model analytes in various samples. For this purpose, we synthesized, characterized, and utilized magnetic multi-walled carbon nanotubes coated with poly 8-hydroxyquinoline (MWCNTs/Fe3O4@PHQ) as a novel sorbent. The impact of various parameters, including sorbent type, sample pH, sample volume, sorbent amount, desorption solvent (type and volume), extraction time, and ionic strength on the extraction efficiency was investigated and optimized. Following the extraction, the desorbed pesticides in acetone were analyzed using gas chromatography with an FID detector. Under the optimized experimental conditions, the proposed method showed excellent linearity in the range of 3-1000 µg/L, low detection limit (0.9-1.5 µg/L), good relative recoveries (86-101.5 %), and high precision (RSD < 6.5 %). Finally, the applicability of this method was evaluated by analyzing the target OPPs in a variety of real samples, and obtained satisfactory results.

Dextrin-assisted gel electromembrane extraction of chiral drugs: Improving the extraction efficiency and investigation of enantioselectivity of extraction.

The present study investigates the use of dextrins (maltodextrin, ß-cyclodextrin, and hydroxypropyl-ß-cyclodextrin) to improve the efficiency of the agarose-based gel electromembrane extraction technique for extracting chiral basic drugs (citalopram, hydroxyzine, and cetirizine). Additionally, it examines the enantioselectivity of the extraction process for these drugs. To achieve these, dextrins were incorporated into either the sample solution, the membrane, or the acceptor solution, and then the extraction procedure was performed. Enantiomers were separated and analyzed using a capillary electrophoresis device equipped with a UV detector. The results obtained under the optimal extraction conditions (sample solution pH: 4.0, acceptor solution pH: 2.0, gel membrane pH: 3.0, agarose concentration: 3 % w/v, stirring rate: 1000 rpm, gel thickness: 4.4 mm, extraction voltage: 62.3 V, and extraction time: 32.1 min) indicated that incorporating dextrins into either the sample solution, membrane or the acceptor solution enhances extraction efficiency by 17.3-23.1 %. The most significant increase was observed when hydroxypropyl-ß-cyclodextrin was added to the acceptor solution. The findings indicated that the inclusion of hydroxypropyl-ß-cyclodextrin in the sample solution resulted in an enantioselective extraction, yielding an enantiomeric excess of 6.42-7.14 %. The proposed method showed a linear range of 5.0-2000 ng/mL for enantiomers of model drugs. The limit of detection and limit of quantification for all enantiomers were found to be < 4.5 ng/mL and <15.0 ng/mL, respectively. Intra- and inter-day RSDs (n = 4) were less than 10.8 %, and the relative errors were less than 3.2 % for all the enantiomers. Finally, the developed method was successfully applied to determine concentrations of enantiomers in a urine sample with relative recoveries of 96.8-99.2 %, indicating good reliability of the developed method.