Unlocking Direct Lithium Extraction in Harsh Conditions through Thiol-Functionalized Metal-Organic Framework Subnanofluidic Membranes.

Metal-organic framework (MOF) membranes with high ion selectivity are highly desirable for direct lithium-ion (Li+) separation from industrial brines. However, very few MOF membranes can efficiently separate Li+ from brines of high Mg2+/Li+ concentration ratios and keep stable in ultrahigh Mg2+-concentrated brines. This work reports a type of MOF-channel membranes (MOFCMs) by growing UiO-66-(SH)2 into the nanochannels of polymer substrates to improve the efficiency of MOF membranes for challenging Li+ extraction. The resulting membranes demonstrate excellent monovalent metal ion selectivity over divalent metal ions, with Li+/Mg2+ selectivity up to 103 since Mg2+ should overcome a higher energy barrier than Li+ when transported through the MOF pores, as confirmed by molecular dynamics simulations. Under dual-ion diffusion, as the Mg2+/Li+ mole ratio of the feed solution increases from 0.2 to 30, the membrane Li+/Mg2+ selectivity decreases from 1516 to 19, corresponding to the purity of lithium products between 99.9 and 95.0%. Further research on multi-ion diffusion that involves Mg2+ and three monovalent metal ions (K+, Na+, and Li+, referred to as M+) in the feed solutions shows a significant improvement in Li+/Mg2+ separation efficiency. The Li+/Mg2+ selectivity can go up to 1114 when the Mg2+/M+ molar concentration ratio is 1:1, and it remains at 19 when the ratio is 30:1. The membrane selectivity is also stable for 30 days in a highly concentrated solution with a high Mg2+/Li+ concentration ratio. These results indicate the feasibility of the MOFCMs for direct lithium extraction from brines with Mg2+ concentrations up to 3.5 M. This study provides an alternative strategy for designing efficient MOF membranes in extracting valuable minerals in the future.

Preclinical evaluation and phase 1 study of the PI3Kα/δ inhibitor TQ-B3525 in Chinese patients with advanced cancers.

BACKGROUND: Phosphatidylinositol 3-kinase (PI3K) inhibitors transformed management of various malignancies. This study preclinically characterized TQ-B3525 (dual PI3Kα/δ inhibitor) and assessed the recommended phase 2 dose (RP2D), safety, efficacy, and pharmacokinetics in relapsed or refractory (R/R) lymphoma or advanced solid tumors (STs). METHODS: Oral TQ-B3525 was given at eight dose levels on a 28-day cycle. Primary end points were dose-limiting toxicity (DLT), maximum tolerated dose (MTD), and safety. RESULTS: TQ-B3525 showed high selectivity and suppressed tumor growth. Between June 12, 2018, and November 18, 2020, 80 patients were enrolled (63 in dose-escalation cohort; 17 in dose-expansion cohort). Two DLTs occurred in two (two of 63, 3.2%) DLT-evaluable patients; MTD was not identified. TQ-B3525 at 20 mg once daily was selected as RP2D. Grade 3 or worse treatment-related adverse events mainly included hyperglycemia (16.3%), neutrophil count decreased (15.0%), and diarrhea (10.0%). Two (2.5%) treatment-related deaths were reported. Sixty patients with R/R lymphoma and 11 advanced STs demonstrated objective response rates of 68.3% and 9.1%, disease control rates of 91.7% and 54.6%, median progression-free survivals of 12.1 and 1.1 months; median overall survivals were not reached. CONCLUSION: TQ-B3525 exhibited rapid absorption and a nearly proportional increase in exposure. Acceptable safety and promising efficacy support further investigation of TQ-B3525 (20 mg once daily) for R/R lymphoma.

Mechano-growth factor regulates periodontal ligament stem cell proliferation and differentiation through Fyn-RhoA-YAP signaling.

BACKGROUND: Mechano-growth factor (MGF), which is a growth factor produced specifically in response to mechanical stimuli, with potential of tissue repair and regeneration. Our previous research has shown that MGF plays a crucial role in repair of damaged periodontal ligaments by promoting differentiation of periodontal ligament stem cells (PDLSCs). However, the molecular mechanism is not fully understood. This study aimed to investigated the regulatory effect of MGF on differentiation of PDLSCs and its molecular mechanism. METHODS: Initially, we investigated how MGF impacts cell growth and differentiation, and the relationship with the activation of Fyn-p-YAPY357 and LATS1-p-YAPS127. Then, inhibitors were used to interfere Fyn phosphorylation to verify the role of Fyn-p-YAP Y357 signal after MGF stimulation; moreover, siRNA was used to downregulate YAP expression to clarify the function of YAP in PDLSCs proliferation and differentiation. Finally, after C3 was used to inhibit the RhoA expression, we explored the role of RhoA in the Fyn-p-YAP Y357 signaling pathway in PDLSCs proliferation and differentiation. RESULTS: Our study revealed that MGF plays a regulatory role in promoting PDLSCs proliferation and fibrogenic differentiation by inducing Fyn-YAPY357 phosphorylation but not LATS1-YAP S127 phosphorylation. Moreover, the results indicated that Fyn could not activate YAP directly but rather activated YAP through RhoA in response to MGF stimulation. CONCLUSION: The research findings indicated that the Fyn-RhoA-p-YAPY357 pathway is significant in facilitating the proliferation and fibrogenic differentiation of PDLSCs by MGF. Providing new ideas for the study of MGF in promoting periodontal regenerative repair.

Interacted Ternary Component Ensuring High-Security Eutectic Electrolyte for High Performance Sodium-Metal Batteries.

Due to the intrinsic flame-retardant, eutectic electrolytes are considered a promising candidate for sodium-metal batteries (SMBs). However, the high viscosity and ruinous side reaction with Na metal anode greatly hinder their further development. Herein, based on the Lewis acid-base theory, a new eutectic electrolyte (EE) composed of sodium bis(trifluoromethanesulfonyl)imide (NaTFSI), succinonitrile (SN), and fluoroethylene carbonate (FEC) is reported. As a strong Lewis base, the ─C≡N group of SN can effectively weaken the interaction between Na+ and TFSI-, achieving the dynamic equilibrium and reducing the viscosity of EE. Moreover, the FEC additive shows a low energy level to construct thicker and denser solid electrolyte interphase (SEI) on the Na metal surface, which can effectively eliminate the side reaction between EE and Na metal anode. Therefore, EE-1:6 + 5% FEC shows high ionic conductivity (2.62 mS cm-1) and ultra-high transference number of Na+ (0.96). The Na||Na symmetric cell achieves stable Na plating/stripping for 1100 h and Na||Na3V2(PO4)3/C cell shows superior long-term cycling stability over 2000 cycles (99.1% retention) at 5 C. More importantly, the Na||NVP/C pouch cell demonstrates good cycling performance of 102.1 mAh g-1 after 135 cycles at 0.5 C with an average coulombic efficiency of 99.63%.

Controlling nonlinear collapse of ellipticity and orientation of a co-variant vector optical field.

A vector optical field with inhomogeneous spatial polarization distribution offers what we believe to be a new paradigm to form controllable filaments. However, it is challenging to steer multiple performances (e.g. number, orientation, and interval) of filaments in transparent nonlinear media at one time. Herein, we theoretically self-design and generate a kind of believed to be novel ellipticity and orientation co-variant vector optical field to interact with Kerr medium to solve this issue. The collapsing behaviors of such a new hybrid vector optical field reveal that, by judiciously adjusting the inherent topological charge and initial phase of incident optical field, we are able to give access to stable collapsing filamentation with tunable numbers, orientations and interval. Additionally, the collapsing patterns presented are immune nearly to the extra random noise. The relevant mechanism behind the collapse of the vector optical field is elucidated as well. The findings in this work may have huge potential in optical signal processing, laser machining, and other related applications.

A case report on deficiency of adenosine deaminase 2 with relapse-remission course and analysis of genotype-phenotype correlation.

Deficiency of adenosine deaminase 2 (DADA2) is a monogenic disease caused by biallelic mutations in adenosine deaminase 2 (ADA2). The varying phenotypes of the disease often lead to delayed diagnosis or misdiagnosis. We report an 11-year-old boy with DADA2 and provide a preliminary analysis of genotype-phenotype correlation. The age of onset of the disease was 8 years old. The disease successively involved the brainstem, muscles, joints, and cerebrum. After three relapse-remission episodes over 3 years, the patient was finally diagnosed with DADA2 by whole-exome sequencing. Compound heterozygous variants in the ADA2 gene (NM_001282225.2: c.1072G>A, p.Gly358Arg; c.419dupC, p.Arg141Lysfs*37) were found in the patient. He did not receive anti-TNF therapy and had no relapse after a 8-month follow-up. We identified a novel variant of the ADA2 gene, and the associated disease course may follow a relapse-remission pattern. Homozygous mutations of p.Gly358Arg can cause pure red cell aplasia, whereas compound heterozygous variations may lead to different phenotypes. Variants in the catalytic domain and frameshift mutations may also cause relatively benign phenotypes besides causing hematological disorders. Further studies are needed to clarify the genotypic-phenotypic relationship of this disease.

Geometry, mechanics and actuation of intrinsically curved folds.

We combine theory and experiments to explore the kinematics and actuation of intrinsically curved folds (ICFs) in otherwise developable shells. Unlike origami folds, ICFs are not bending isometries of flat sheets, but arise via non-isometric processes (growth/moulding) or by joining sheets along curved boundaries. Experimentally, we implement both, first making joined ICFs from paper, then fabricating flat liquid crystal elastomer (LCE) sheets that morph into ICFs upon heating/swelling via programmed metric changes. Theoretically, an ICF's intrinsic geometry is defined by the geodesic curvatures on either side, κgi. Given these, and a target 3D fold-line, one can construct the entire surface isometrically, and compute the bending energy. This construction shows ICFs are bending mechanisms, with a continuous family of isometries trading fold angle against fold-line curvature. In ICFs with symmetric κgi, straightening the fold-line culminates in a fully-folded flat state that is deployable but weak, while asymmetric ICFs ultimately lock with a mechanically strong finite-angle. When unloaded, freely-hinged ICFs simply adopt the (thickness t independent) isometry that minimizes the bend energy. In contrast, in LCE ICFs a competition between flank and ridge selects a ridge curvature that, unusually, scales as t-1/7. Finally, we demonstrate how multiple ICFs can be combined in one LCE sheet, to create a versatile intrinsically curved gripper that lifts a heavy weight.

Suppressing the Thermal Quenching Effect via a Cluster Conformer in Copper(I)-Iodide Coordination Polymeric Phosphors for High-Power White LED Lighting.

High-power LED lighting is a crucial challenge due to the notorious thermal quenching (TQ) effect of traditional phosphors at high operating currents, which would result in poor device performance and hamper practical optoelectronic application. Herein, we demonstrate ligand engineering of a cubane- versus staircase-like [Cu4I4] conformer as a node in coordination polymers, which remarkably suppresses the TQ effect of cluster-based photoluminescence. For complex 1 (the formula [Cu4I4(bbimb)2]n) with the cubane-like [Cu4I4] conformer as a node, the metallophilicity interaction enables ultrabright triplet emission with a photoluminescence quantum yield over 82%, and the phonon-assisted detrapping process of excitons effectively suppresses the TQ effect in the wide temperature range. In contrast, the staircase-like [Cu4I4] conformer as a node in complex 2 (the formula [Cu4I4(bbtmb)2]n) exhibits a serious TQ effect over the investigated temperature. Phosphor-converted white LEDs (pc-wLEDs) were fabricated by integrating the cluster-based coordination polymers as a color converter, and their electroluminescence performances were investigated under high bias currents. The prototype pc-wLED device by incorporating the phosphor with the suppressed TQ effect exhibits a continuous rise in brightness under a high bias current of 300 mA. The results demonstrate that ligand engineering of the cluster conformer via suppressing the TQ effect proves efficient in designing an ideal color converter for high-power pc-wLED lighting.

Neuroprotection by tetramethylpyrazine and its synthesized analogues for central nervous system diseases: a review.

BACKGROUND: Due to the global increase in aging populations and changes in modern lifestyles, the prevalence of neurodegenerative diseases, cerebrovascular disorders, neuropsychiatrcic conditions, and related ailments is rising, placing an increasing burden on the global public health system. MATERIALS AND METHODS: All studies on tetramethylpyrazine (TMP) and its derivatives were obtained from reputable sources such as PubMed, Elsevier, Library Genesis, and Google Scholar. Comprehensive data on TMP and its derivatives was meticulously compiled. RESULTS: This comprehensive analysis explains the neuroprotective effects demonstrated by TMP and its derivatives in diseases of the central nervous system. These compounds exert their influence on various targets and signaling pathways, playing crucial roles in the development of various central nervous system diseases. Their multifaceted mechanisms include inhibiting oxidative damage, inflammation, cell apoptosis, calcium overload, glutamate excitotoxicity, and acetylcholinesterase activity. CONCLUSION: This review provides a brief summary of the most recent advancements in research on TMP and its derivatives in the context of central nervous system diseases. It involves synthesizing analogs of TMP and evaluating their effectiveness in models of central nervous system diseases. The ultimate goal is to facilitate the practical application of TMP and its derivatives in the future treatment of central nervous system diseases.

[Clinical Characteristics Analysis of 1051 Cases of Cleft Lip With/Without Cleft Palate in the Ethnic Tibetan Population]. / 1051ä¾‹è—æ—å”‡è ­è£‚æ‚£è€ ä¸´åºŠç‰¹å¾åˆ†æž.

Objective: To examine the characteristics of the prevalence of congenital cleft lip with/without cleft palate in the ethnic Tibetan population and to provide support for the precise prevention and treatment of cleft lip with/without cleft palate in the Tibetan population. Methods: The clinical data of Tibetan patients with cleft lip with/without cleft palate were collected and the clinical characteristics of the patients were analyzed. The patients' age ranged from 2 months to 51 years old. All the subjects were admitted to West China Stomatology Hospital, Sichuan University for the treatment of cleft lip with/without cleft palate between January 2016 and August 2023. Most of the subjects came from Sichuan Province and the Tibet Autonomous Region. Results: A total of 1051 patients were enrolled and children aged under 12 months (460 cases) accounted for the largest proportion. Among the subjects, 383 had cleft lip only (36.44%), 140 had cleft palate only (13.32%), and 528 had cleft lip with cleft palate (50.24%). The male-to-female ratios of patients with cleft lip only (0.99∶1), cleft palate only (0.54∶1), and cleft lip with cleft palate (1.67∶1) exhibited significant differences (P<0.001). However, there was no significant difference in the male-to-female ratio in patients with cleft lip only or those with cleft lip with cleft palate when the subjects were divided into two groups according to whether they had unilateral or bilateral cleft lip with/without cleft palate. Most of the patients with bilateral cleft lip were female, while most of the patients with unilateral cleft lip and unilateral or bilateral cleft lip with cleft palate were male. The unilateral cleft lip with/without cleft palate was located predominantly on the left side. Syndromic cleft lip with/without cleft palate accounted for 3.43% of all the cases and the most common concomitant deformity was congenital heart disease. 3.81% (40 cases) of the patients had a family history. In the patients with cleft lip only and those with cleft palate only, the proportion of patients having parents with corresponding phenotypes was higher than those of other phenotypes of cleft lip with/without cleft palate. Regarding the birth time distribution of the children with cleft lip with/without cleft palate, Spring saw the highest number of births of these children (311 cases, 29.59%), while Winter saw the lowest number of births (231 cases, 21.98%). Conclusion: The cases of cleft lip with/without cleft palate in the ethnic Tibetan population are predominantly cleft lip and palate. Unilateral cleft lip only or cleft lip with palate is predominantly located on the left side. Lip disease phenotypes may be more heritable.

[Distribution of ABO and Rh Blood Groups in Tibetan and Han Populations With Cleft Lip and Palate in a Tertiary Hospital in Western China]. / ä¸­å›½è¥¿éƒ¨æŸä¸‰ç”²åŒ»é™¢è—æ—ä¸Žæ±‰æ—å”‡è ­è£‚æ‚£è€ ABO血型及Rhè¡€åž‹åˆ†å¸ƒç ”ç©¶.

Objective: Congenital cleft lip and palate is a common birth defect that seriously affects the lives of the afflicted children and their families. Previously, no research has been done to investigate the pathogenic characteristics of cleft lip and palate among ethnic minorities, for example, Tibetans, a minority ethnic group with a large population in China. This study aims to investigate the relationship between the occurrence of cleft lip and palate in Tibetans and Han Chinese in western China and the distribution of ABO blood groups and Rh blood groups to provide a theoretical basis for the precise prevention and treatment of cleft lip and palate. Methods: In this study, statistics on Tibetan patients with cleft lip and palate, some Han patients with cleft lip and palate, and normal controls from western China were retrospectively collected. All participants were patients from West China Stomatology Hospital, Sichuan University. All patients with cleft lip and palate received treatment at the hospital between January 2016 and September 2023. The normal controls were outpatients or inpatients who did not have cleft lip and palate, and who received treatment at the hospital between January 2020 and October 2023. Information on the A, B, O, and AB blood groups and Rh positive and negative blood groups of the patients was collected and compared with that of the normal controls. The incidence of different phenotypes, including cleft lip alone, cleft palate alone, and cleft lip with cleft palate, in patients of blood groups A, B, O and AB were statistically analyzed by Chi-square test. Results: A total of 1227 Tibetan patients with cleft lip and palate, 4064 Han patients with cleft lip and palate, and 5360 normal controls were included in the study. Among all the patients with cleft lip and palate, 1863 had cleft lip alone, 1425 had cleft palate alone, and 2003 had cleft lip with cleft palate. The ABO blood group distribution of Tibetan patients with cleft lip and palate was characterized as O>B>A>AB, with Rh positive blood group accounting for 100%, blood type O accounting for 41.15%, and blood type B accounting for 30.64%. The blood group distribution of the Han patients with cleft lip and palate was characterized as O>A>B>AB, with Rh positive blood group accounting for 99.58%, blood type O accounting for 35.78%, and type A accounting for 30.54%. There was a significant difference in ABO blood groups between Tibetan and Han patients with cleft lip and palate (P<0.005), but no significant difference in Rh blood groups. The ABO blood group distribution of the Tibetan patients with cleft lip and palate showed an obvious difference from that of the control group, while those of the Han patients with cleft lip and cleft palate and the control group did not show obvious differences. In the analysis of the subtypes, it was found that the blood group distribution in the subtypes of cleft lip alone, cleft palate alone, and cleft lip with cleft palate in the Tibetan population was O>B>A>AB, while that in the Han Chinese population was O>A>B>AB. There were differences in blood group distribution between Tibetans and Hans of the subtypes of cleft lip alone and cleft lip with cleft palate (P<0.001), but there was no difference in blood group distribution in the population of cleft palate-only subtype. The proportion of blood type O in Tibetan patients with cleft lip and palate was significantly higher than that in the Han patients with cleft lip and palate. The blood group distribution of Tibetan patients with cleft lip and palate in Sichuan Province, Xizang Autonomous Region, and Qinghai Province was always O>B>A>AB. Tibetan patients from Shiqu County and Baiyu County, Ganzi Tibetan Autonomous Prefecture and Chaya County, Qamdo City were predominantly of blood type B, and those from other regions were mainly of blood type O. Conclusion: There were significant differences in the phenotype composition and ABO blood group distribution between the Tibetan and Han populations with cleft lip and palate in western China. The distribution of blood group O in the population with cleft lip and palate was higher than that in the normal population, and the same trend was observed for different phenotypes. However, differences between Tibetan and Han populations in ABO blood group distribution were only found in the phenotypes of cleft lip only and cleft lip with palate. Tibetans with blood type O are more prone to cleft lip deformity than Han people, and the effect in the phenotype of cleft lip with palate is less pronounced than that in the phenotype of cleft lip only.

Surface Instability in a Nematic Elastomer.

Liquid crystal elastomers (LCEs) are soft phase-changing solids that exhibit large reversible contractions upon heating, Goldstone-like soft modes, and resultant microstructural instabilities. We heat a planar LCE slab to isotropic, clamp the lower surface, then cool back to nematic. Clamping prevents macroscopic elongation, producing compression and microstructure. We see that the free surface destabilizes, adopting topography with amplitude and wavelength similar to thickness. To understand the instability, we numerically compute the microstructural relaxation of a "nonideal" LCE energy. Linear stability reveals a Biot-like scale-free instability, but with oblique wave vector. However, simulation and experiment show that, unlike classic elastic creasing, instability culminates in a crosshatch without cusps or hysteresis, and is constructed entirely from low-stress soft modes.

Optimization-informed Rule Extraction for HVAC system: A Case Study of Dedicated Outdoor Air System Control in a Mixed-Humid Climate Zone.

In the era of post-Coronavirus Disease 2019, the dedicated outdoor air system (DOAS), which provides 100% outdoor air for the building, is widely acknowledged as it can ensure acceptable indoor air quality by delivering fresh outdoor air to occupied space. The DOAS with a proper design and operation can provide sufficient ventilation and dehumidification while achieving energy efficiency. Nonetheless, there is limited guidance in determining the optimal control sequence of the DOAS for the designers and operators to implement in practice. Accordingly, in practice, a number of issues have been acknowledged in the design and control phases of DOAS, including insufficient ventilation and dehumidification, and increasing supply air dry-bulb temperature in fear of over-cooling, which might cause significant discomfort and energy waste. There have been efforts to develop high-performing DOAS controls for better energy efficiency. However, such controls are often complex, or difficult to interpret, for building designers and operators to consider in practice. In this regard, this paper explores a simulation-based framework for generating a supply air temperature control sequence of the DOAS not only to ensure improved energy-saving potential but also to guarantee the implement-ability of the control logic. The U.S Department of Energy prototype primary school with dynamic occupancy profiles was modeled with a whole building simulation program, EnergyPlus. The model consists of a DOAS with an exhaust air energy recovery system for ventilation and fan-coil units for space cooling and heating. Then, a Genetic Algorithm was adopted to find the true optimal supply air temperature control sequence in terms of minimizing the energy cost of the heating, ventilation, and air conditioning system operation. Lastly, Decision Tree was adopted to extract rules out of the optimums to derive an implementable sequence of operation for the DOAS supply air temperature. A total of 12 week-simulation including four weeks of heating, cooling, and shoulder seasons, separately, under the weather condition of New York City was conducted for the case study. This case study identified that the optimization-informed rule extraction-based control, when compared to conventional outdoor air temperature-based reset control, could save about 13% of energy cost and 25% of energy consumption throughout the heating, cooling, and shoulder seasons. It is notable that the energy-saving was mainly achieved by reducing the heating energy consumption. Importantly, it nearly corresponds to the true optimal control result, which reduces approximately 14% of energy cost and 27% of energy consumption. From the results, it can be highlighted that the optimization-informed rule extraction can be as energy effective as the optimal control, while significantly reducing the complexity of the control.

Ferroptosis and Pyroptosis in Epilepsy.

Epilepsy is sudden, recurrent, and transient central nervous system dysfunction caused by abnormal discharge of neurons in the brain. Ferroptosis and pyroptosis are newly discovered ways of programmed cell death. One of the characteristics of ferroptosis is the oxidative stress generated by lipid peroxides. Similarly, pyroptosis has unique pro-inflammatory properties. As both oxidative stress and neuroinflammation are significant contributors to the pathogenesis of epilepsy, increasing evidence shows that ferroptosis and pyroptosis are closely related to epilepsy. This article reviews the current comprehension of ferroptosis and pyroptosis and elucidates potential mechanisms by which ferroptosis and pyroptosis may contribute to epilepsy. In addition, we also highlight the possible interactions between ferroptosis and pyroptosis because they reportedly coexist in many diseases, and increasing studies have demonstrated the convergence of pathways between the two. This is of great significance for explaining the occurrence and development of epilepsy and provides a new therapeutic perspective for the treatment of epilepsy.

Data aggregation algorithm for wireless sensor networks with different initial energy of nodes.

Data aggregation plays a critical role in sensor networks for efficient data collection. However, the assumption of uniform initial energy levels among sensors in existing algorithms is unrealistic in practical production applications. This discrepancy in initial energy levels significantly impacts data aggregation in sensor networks. To address this issue, we propose Data Aggregation with Different Initial Energy (DADIE), a novel algorithm that aims to enhance energy-saving, privacy-preserving efficiency, and reduce node death rates in sensor networks with varying initial energy nodes. DADIE considers the transmission distance between nodes and their initial energy levels when forming the network topology, while also limiting the number of child nodes. Furthermore, DADIE reconstructs the aggregation tree before each round of data transmission. This allows nodes closer to the receiving end with higher initial energy to undertake more data aggregation and transmission tasks while limiting energy consumption. As a result, DADIE effectively reduces the node death rate and improves the efficiency of data transmission throughout the network. To enhance network security, DADIE establishes secure transmission channels between transmission nodes prior to data transmission, and it employs slice-and-mix technology within the network. Our experimental simulations demonstrate that the proposed DADIE algorithm effectively resolves the data aggregation challenges in sensor networks with varying initial energy nodes. It achieves 5-20% lower communication overhead and energy consumption, 10-20% higher security, and 10-30% lower node mortality than existing algorithms.

Performance Analysis of Ferronickel Slag-Ordinary Portland Cement Pervious Concrete.

It is unknown whether Ferronickel slag (FNS)-ordinary Portland cement (OPC)-based pervious concrete (FOPC) is feasible. To this end, a feasibility study was conducted on FOPC. Firstly, a detailed microscopic examination of the FNS powder was conducted, encompassing analyses of its particle size distribution, SEM, EDS, and chemical composition. These analyses aimed to establish the suitability of a composite of FNS and OPC as a composite cementitious material. Subsequent experimentation focused on evaluating the compressive strength of the composite paste material with varying mixed proportions, revealing a slight reduction in strength as the FNS substitution rate increased. Furthermore, the study designed eighteen different mix proportions of FOPC to investigate the key physical properties, including porosity, density, compressive strength, and the coefficient of permeability. Findings indicated that increases in the cementitious material proportion correlate with enhanced concrete strength, where the ratio of cementitious to aggregate increased by 6.7% and 16.5%, and the strength of FOPC increased by 10-13% and 30-50%, respectively. Conversely, a rise in the FNS substitution rate led to a reduction in compressive strength across different mix ratios. Additionally, the ratio of paste material to aggregate was found to significantly influence the permeability coefficient. These comprehensive performance evaluations suggest that incorporating FNS into OPC for pervious concrete applications is a feasible approach, offering valuable insights for the promotion of waste reuse and the advancement of energy conservation and emissions reduction efforts.

[Start-up and Recovery Performance of ANAMMOX Reactors Under Long-term Starvation].

The application of ANAMMOX technology is constrained by sluggish growth and difficulty in enriching ANAMMOX bacteria. Long-term starvation of functioning bacteria due to limited substrate supply makes the steady operation of ANAMMOX reactors more difficult. Re-examining the start-up and recovery performance of the ANAMMOX reactor and identifying its resistance mechanism are important from the standpoint of long-term starvation. By inoculating nitrifying and denitrifying sludge under various operating circumstances, the ANAMMOX reactors were successfully started. Under various start-up procedures, the tolerance mechanism and recovery performance were examined. The outcomes demonstrated that the denitrifying sludge-inoculated reactor operated steadily with a high substrate concentration and low flow rate. After 85 days of operation, the removal efficiencies of NH4+-N, NO2--N, and total nitrogen reached 98.7%, 99.3%, and 89.3%, respectively. After 144 days of starvation and 30 days of recovery, the better nitrogen removal performance was achieved at a low substrate concentration and high flow rate, and the removal efficiencies were 99.8% （NH4+-N）, 99.8% （NO2--N）, and 93.6% （total nitrogen）. During the starvation, extracellular polymeric substances wrapped the ANAMMOX bacteria and kept them intact to resist long-term starvation stress. The expression of nirS, hzsA, and hdh genes ensured the synthesis of nitrite/nitric oxide oxidoreductase, hydrazine synthase, and hydrazine dehydrogenase to maintain ANAMMOX activity. There was no significant difference in the relative abundance of ANAMMOX bacteria before and after starvation recovery. Candidatus Kuenenia had better anti-hunger ability, and the relative abundance increased by more than 86% after 30 days of recovery, confirming its tolerance to long-term starvation.

An anoikis-related lncRNA signature may predict the prognosis, immune infiltration, and drug sensitivity in esophageal cancer.

Background: Esophageal cancer (EC) is a prevalent malignancy with heterogeneous outcomes. This study explores the significance of anoikis-related long non-coding RNAs (lncRNAs) in EC, aiming to unravel their molecular roles and clinical implications. Methods: Transcriptome and clinical data were obtained from TCGA database for EC samples. We identified anoikis-related genes and lncRNAs by Pearson correlation analysis. The risk score model hinged on prognostic lncRNAs filtered from multiple steps. Risk scores were calculated using the derived formula, and categorized patients into low- and high-risk groups. Model robustness was assessed through Kaplan-Meier (KM) survival analysis and Receiver Operating Characteristic (ROC) curve, with clinical utility achieved via a constructed nomogram. We also explored the interplay between the risk score and immune cell infiltration, and investigated drug sensitivity. Results: We identified 2365 anoikis-related lncRNAs through co-expression analysis, including 1415 significant lncRNAs differentially expressed between normal and tumor samples. A risk score model was constructed from ten prognostic lncRNAs. The risk score model effectively stratified patients based on the median score, and its predictive capacity was validated through KM survival, ROC curve analyses, and the external GSE53622 dataset. The nomogram provided a practical tool for individualized prognosis evaluation. We unveiled significant correlations between specific immune cell subsets and the risk score. Eosinophils and common lymphoid progenitors exhibited positive associations, while endothelial cells and myeloid dendritic cells showed negative correlations. Drug sensitivity analysis revealed potential sensitive drugs for EC treatment that aligned with the risk subgroups. Conclusion: This study established an anoikis-related lncRNAs risk score model that may predict the prognosis, immune infiltration, and drug sensitivity in EC, in hope of facilitating tailored patient management.

Mechanism Research of PZD Inhibiting Lung Cancer Cell Proliferation, Invasion, and Migration based on Network Pharmacology.

BACKGROUND: A classic Chinese medicine decoction, Pinellia ternata (Thunb.) Breit.-Zingiber officinale Roscoe (Ban-Xia and Sheng-Jiang in Chinese) decoction (PZD), has shown significant therapeutic effects on lung cancer. OBJECTIVE: This study aimed to explore and elucidate the mechanism of action of PZD on lung cancer using network pharmacology methods. METHODS: Active compounds were selected according to the ADME parameters recorded in the TCMSP database. Potential pathways related to genes were identified through GO and KEGG analysis. The compoundtarget network was constructed by using Cytoscape 3.7.1 software, and the core common targets were obtained by protein-protein interaction (PPI) network analysis. Batch molecular docking of small molecule compounds and target proteins was carried out by using the AutoDock Vina program. Different concentrations of PZD water extracts (10, 20, 40, 80, and 160 µg/mL) were used on lung cancer cells. Moreover, MTT and Transwell experiments were conducted to validate the prominent therapeutic effects of PZD on lung cancer cell H1299. RESULTS: A total of 381 components in PZD were screened, of which 16 were selected as bioactive compounds. The compound-target network consisting of 16 compounds and 79 common core targets was constructed. MTT experiment showed that the PZD extract could inhibit the cell proliferation of NCI-H1299 cells, and the IC50 was calculated as 97.34 ± 6.14 µg/mL. Transwell and wound-healing experiments showed that the PZD could significantly decrease cell migration and invasion at concentrations of 80 and 160 µg/mL, respectively. The in vitro experiments confirmed that PZD had significant therapeutic effects on lung cancer cells, mainly through the PI3K/AKT signaling pathway. CONCLUSION: PZD could inhibit the cell proliferation, migration, and invasion of NCI-H1299 cells partially through the PI3K/AKT signaling pathway. These findings suggested that PZD might be a potential treatment strategy for lung cancer patients.

The combined effect of carbon starvation and exogenous riboflavin accelerated the Pseudomonas aeruginosa-induced nickel corrosion.

The primary objective of this study is to elucidate the synergistic effect of an exogenous redox mediator and carbon starvation on the microbiologically influenced corrosion (MIC) of metal nickel (Ni) by nitrate reducing Pseudomonas aeruginosa. Carbon source (CS) starvation markedly accelerates Ni MIC by P. aeruginosa. Moreover, the addition of exogenous riboflavin significantly decreases the corrosion resistance of Ni. The MIC rate of Ni (based on corrosion loss volume) is ranked as: 10 % CS level + riboflavin > 100 % CS level + riboflavin > 10 % CS level > 100 % CS level. Notably, starved P. aeruginosa biofilm demonstrates greater aggressiveness in contributing to the initiation of surface pitting on Ni. Under CS deficiency (10 % CS level) in the presence of riboflavin, the deepest Ni pits reach a maximum depth of 11.2 µm, and the corrosion current density (icorr) peak at approximately 1.35 × 10-5 A·cm-2, representing a 2.6-fold increase compared to the full-strength media (5.25 × 10-6 A·cm-2). For the 10 % CS and 100 % CS media, the addition of exogenous riboflavin increases the Ni MIC rate by 3.5-fold and 2.9-fold, respectively. Riboflavin has been found to significantly accelerate corrosion, with its augmentation effect on Ni MIC increasing as the CS level decreases. Overall, riboflavin promotes electron transfer from Ni to P. aeruginosa, thus accelerating Ni MIC.