Highly Sensitive and Selective Graphene Nanoribbon Based Enzymatic Glucose Screen-Printed Electrochemical Sensor.

A simple, sensitive, cost effective, and reliable enzymatic glucose biosensor was developed and tested. Nitrogen-doped heat-treated graphene oxide nanoribbons (N-htGONR) were used for modification of commercially available screen-printed carbon electrodes (SPCEs), together with MnO2 and glucose oxidase. The resulting sensors were optimized and used to detect glucose in a wide linear range (0.05-5.0 mM) by a simple amperometric method, where the limit of detection was determined to be 0.008 mM. (lifetime), and reproducibility studies were also carried out and yielded favorable results. The sensor was then tested against potential interfering species present in food and beverage samples before its application to real matrix. Spiked beer samples were analyzed (with glucose recovery between 93.5 and 103.5%) to demonstrate the suitability of the developed sensor towards real food and beverage sample applications.

Highly Sensitive Amperometric Detection of Hydrogen Peroxide in Saliva Based on N-Doped Graphene Nanoribbons and MnO2 Modified Carbon Paste Electrodes.

Four different graphene-based nanomaterials (htGO, N-htGO, htGONR, and N-htGONR) were synthesized, characterized, and used as a modifier of carbon paste electrode (CPE) in order to produce a reliable, precise, and highly sensitive non-enzymatic amperometric hydrogen peroxide sensor for complex matrices. CPE, with their robustness, reliability, and ease of modification, present a convenient starting point for the development of new sensors. Modification of CPE was optimized by systematically changing the type and concentration of materials in the modifier and studying the prepared electrode surface by cyclic voltammetry. N-htGONR in combination with manganese dioxide (1:1 ratio) proved to be the most appropriate material for detection of hydrogen peroxide in pharmaceutical and saliva matrices. The developed sensor exhibited a wide linear range (1.0-300 µM) and an excellent limit of detection (0.08 µM) and reproducibility, as well as high sensitivity and stability. The sensor was successfully applied to real sample analysis, where the recovery values for a commercially obtained pharmaceutical product were between 94.3% and 98.0%. Saliva samples of a user of the pharmaceutical product were also successfully analyzed.

A Novel Reduced Graphene Oxide Modified Carbon Paste Electrode for Potentiometric Determination of Trihexyphenidyl Hydrochloride in Pharmaceutical and Biological Matrices.

A novel promising carbon paste electrode with excellent potentiometric properties was prepared for the analysis of trihexyphenidyl hydrochloride (THP), the acetylcholine receptor and an anticholinergic drug in real samples. It contains 10.2% trihexyphenidy-tetraphenylborate ionic pair as the electroactive material, with the addition of 3.9% reduced graphene oxide and 0.3% of anionic additive into the paste, which consists of 45.0% dibutylphthalate as the solvent mediator and 40.6% graphite. Under the optimized experimental conditions, the electrode showed a Nernstian slope of 58.9 ± 0.2 mV/decade with a regression coefficient of 0.9992. It exhibited high selectivity and reproducibility as well as a fast and linear dynamic response range from 4.0 × 10-7 to 1.0 × 10-2 M. The electrode remained usable for up to 19 days. Analytical applications showed excellent recoveries ranging from 96.8 to 101.7%, LOD was 2.5 × 10-7 M. The electrode was successfully used for THP analysis of pharmaceutical and biological samples.

Efficient Chitosan/Nitrogen-Doped Reduced Graphene Oxide Composite Membranes for Direct Alkaline Ethanol Fuel Cells.

Herein, we prepared a series of nanocomposite membranes based on chitosan (CS) and three compositionally and structurally different N-doped graphene derivatives. Two-dimensional (2D) and quasi 1D N-doped reduced graphene oxides (N-rGO) and nanoribbons (N-rGONRs), as well as 3D porous N-doped graphitic polyenaminone particles (N-pEAO), were synthesized and characterized fully to confirm their graphitic structure, morphology, and nitrogen (pyridinic, pyrrolic, and quaternary or graphitic) group contents. The largest (0.07%) loading of N-doped graphene derivatives impacted the morphology of the CS membrane significantly, reducing the crystallinity, tensile properties, and the KOH uptake, and increasing (by almost 10-fold) the ethanol permeability. Within direct alkaline ethanol test cells, it was found that CS/N rGONRs (0.07 %) membrane (Pmax. = 3.7 mWcm-2) outperformed the pristine CS membrane significantly (Pmax. = 2.2 mWcm-2), suggesting the potential of the newly proposed membranes for application in direct ethanol fuel cells.

Development of the New Fluoride Ion-Selective Electrode Modified with FexOy Nanoparticles.

A new modified ion-selective electrode with membranes of LaF3 single crystals with different internal contacts (solid steel or electrolyte) and with FexOy nanoparticles as loading was developed. The best response characteristic with linear potential change was found in the fluoride concentration range from 10-1 to 3.98 × 10-7 M. The detection limit for the electrolyte contact was determined at 7.41 × 10-8 M with a regression coefficient of 0.9932, while the regression coefficient for the solid contact was 0.9969. The potential change per concentration decade ranged from 50.3 to 62.4 mV, depending on whether the contact was solid or electrolytic. The prepared modified electrode has a long lifetime, as well as the possibility of application in different positions (solid contact), and it can also be used for the determination of iron ions. The electrode characterization was performed with scanning electron microscopy and elemental analysis with the technique of electron-dispersive X-ray spectroscopy.

Design of active and stable Co-Mo-Sx chalcogels as pH-universal catalysts for the hydrogen evolution reaction.

Three of the fundamental catalytic limitations that have plagued the electrochemical production of hydrogen for decades still remain: low efficiency, short lifetime of catalysts and a lack of low-cost materials. Here, we address these three challenges by establishing and exploring an intimate functional link between the reactivity and stability of crystalline (CoS2 and MoS2) and amorphous (CoSx and MoSx) hydrogen evolution catalysts. We propose that Co(2+) and Mo(4+) centres promote the initial discharge of water (alkaline solutions) or hydronium ions (acid solutions). We establish that although CoSx materials are more active than MoSx they are also less stable, suggesting that the active sites are defects formed after dissolution of Co and Mo cations. By combining the higher activity of CoSx building blocks with the higher stability of MoSx units into a compact and robust CoMoSx chalcogel structure, we are able to design a low-cost alternative to noble metal catalysts for efficient electrocatalytic production of hydrogen in both alkaline and acidic environments.

The Synthesis of Diquinone and Dihydroquinone Derivatives of Calix[4]arene and Electrochemical Characterization on Au(111) surface.

Several new electroactive diquinone and dihydroquinone derivatives of calix[4]arene bearing anchor functional groups were designed, synthesized and characterized. A method for selective protection of the hydroquinone -OH groups with trimethylsilyl groups (TMS) either on lower-rim or on upper-rim was developed. Four selected molecules - with sulfide anchor groups and carboxylic anchor groups - were adsorbed onto Au(111) single crystal surface using ex-situ and insitu self-assembly methods. Adsorbed molecules were then electrochemically probed with cyclic voltammetry. All adsorbed molecules showed redox response which changed during cycling. After conditioning CVs stabilized and showed two distinct current peaks for all molecules. Synthesized and electrochemically probed molecules are of interest to: Li-ion batteries (as cathode materials and overcharge protection), beyond Li-ion batteries and redox-flow batteries.

Influence of the Electrode Deposition Method of Graphene-Based Catalyst Inks for ADEFC on Performance.

The utilization of graphene as a catalyst support has garnered significant attention due to its potential for enhancing fuel cell performance. However, a critical challenge in electrode production still lies in the electrode preparation technologies and the restacking of graphene sheets, which can greatly impact the fuel cell performance alongside with catalyst development. This study aimed to investigate the impact of different electrode deposition methods for N-rGO-based catalyst inks on catalyst layer morphology, with a specific focus on graphene sheet orientation and its influence on the performance of alkaline direct ethanol fuel cells (ADEFCs). The dispersion behavior and ink stability of the catalysts were assessed using ultraviolet-visible light (UV-vis), ζ potential, and dynamic light scattering techniques. The morphology and physical properties of the gas diffusion electrodes (GDEs) were analyzed through Brunauer-Emmett-Teller measurements, contact angle measurements and scanning electron microscopy (SEM) combined with energy-dispersive spectroscopy. The electrochemical behavior was evaluated both ex-situ, utilizing half-cell GDE measurements, and in situ, through single-cell tests. The N-rGO-based membrane electrode assembly, comprising Pt-free catalysts and a biobased membrane, exhibited outstanding performance in ADEFCs, as evidenced by high maximum power density values and long-term durability. The N-rGO-based membrane electrode assembly has demonstrated remarkable potential for high-performance fuel cells, presenting an exciting avenue for further exploration.

High performance chitosan/nanocellulose-based composite membrane for alkaline direct ethanol fuel cells.

Polysaccharide anion exchange membranes (AEMs) containing chitosan (CS), cellulose nanofibrils (CNFs) and CNFs quaternized with poly(diallyldimethylammonium chloride) (CNF(P)s) were developed for use in alkaline direct ethanol fuel cells (ADEFCs). The resulting composite membranes prepared by the solvent casting process based on an experimental design were comprehensively assessed for morphology, KOH uptake, swelling ratio, EtOH permeability, mechanical properties, ionic conductivity, and cell performance. The fabricated CS-based composite membranes with CNF(P) fillers were superior to the commercial Fumatech FAA-3-50 membrane in terms of Young's modulus and tensile strength (69 % and 85 % higher, respectively), ion exchange capacity (169 % higher), and ionic conductivity (228 % higher). Single fuel cell tests have shown excellent performance of the CS-based membranes with CNF and CNF(P) fillers, as they exhibited up to 86 % improvement in power density at 80 °C compared to the commercial membrane (65.1 mW/cm2 vs. 35.1 mW/cm2) and higher maximum power density at all test conditions.

Mixed Transition-Metal Oxides on Reduced Graphene Oxide as a Selective Catalyst for Alkaline Oxygen Reduction.

The development of highly efficient, stable, and selective non-precious-metal catalysts for the oxygen reduction reaction (ORR) in alkaline fuel cell applications is essential. A novel nanocomposite of zinc- and cerium-modified cobalt-manganese oxide on reduced graphene oxide mixed with Vulcan carbon (ZnCe-CMO/rGO-VC) was prepared. Physicochemical characterization reveals uniform distribution of nanoparticles strongly anchored on the carbon support resulting in a high specific surface area with abundant active sites. Electrochemical analyses demonstrate a high selectivity in the presence of ethanol compared to commercial Pt/C and excellent ORR activity and stability with a limiting current density of -3.07 mA cm-2, onset and half-wave potentials of 0.91 and 0.83 V vs reversible hydrogen reference electrode (RHE), respectively, a high electron transfer number, and an outstanding stability of 91%. Such a catalyst could be an efficient and cost-effective alternative to modern noble-metal ORR catalysts in alkaline media.

Study on Commercially Available Membranes for Alkaline Direct Ethanol Fuel Cells.

This study provides a comparison of different commercially available low-cost anion exchange membranes (AEMs), a microporous separator, a cation exchange membrane (CEM), and an anionic-treated CEM for their application in the liquid-feed alkaline direct ethanol fuel cell (ADEFC). Moreover, the effect on performance was evaluated taking two different modes of operation for the ADEFC, with AEM or CEM, into consideration. The membranes were compared with respect to their physical and chemical properties, such as thermal and chemical stability, ion-exchange capacity, ionic conductivity, and ethanol permeability. The influence of these factors on performance and resistance was determined by means of polarization curve and electrochemical impedance spectra (EIS) measurements in the ADEFC. In addition, the influence of two different commercial ionomers on the structure and transport properties of the catalyst layer and on the performance were analyzed with scanning electron microscopy, single cell tests, and EIS. The applicability barriers of the membranes were pointed out, and the ideal combinations of membrane and ionomer for the liquid-feed ADEFC achieved power densities of approximately 80 mW cm-2 at 80 °C.

Efficiency of Neat and Quaternized-Cellulose Nanofibril Fillers in Chitosan Membranes for Direct Ethanol Fuel Cells.

In this work, fully polysaccharide based membranes were presented as self-standing, solid polyelectrolytes for application in anion exchange membrane fuel cells (AEMFCs). For this purpose, cellulose nanofibrils (CNFs) were modified successfully with an organosilane reagent, resulting in quaternized CNFs (CNF (D)), as shown by Fourier Transform Infrared Spectroscopy (FTIR), Carbon-13 (C13) nuclear magnetic resonance (13C NMR), Thermogravimetric Analysis (TGA)/Differential Scanning Calorimetry (DSC), and ζ-potential measurements. Both the neat (CNF) and CNF(D) particles were incorporated in situ into the chitosan (CS) membrane during the solvent casting process, resulting in composite membranes that were studied extensively for morphology, potassium hydroxide (KOH) uptake and swelling ratio, ethanol (EtOH) permeability, mechanical properties, ionic conductivity, and cell performance. The results showed higher Young's modulus (119%), tensile strength (91%), ion exchange capacity (177%), and ionic conductivity (33%) of the CS-based membranes compared to the commercial Fumatech membrane. The addition of CNF filler improved the thermal stability of the CS membranes and reduced the overall mass loss. The CNF (D) filler provided the lowest (4.23 × 10-5 cm2 s-1) EtOH permeability of the respective membrane, which is in the same range as that of the commercial membrane (3.47 × 10-5 cm2s-1). The most significant improvement (~78%) in power density at 80 °C was observed for the CS membrane with neat CNF compared to the commercial Fumatech membrane (62.4 mW cm-2 vs. 35.1 mW cm-2). Fuel cell tests showed that all CS-based anion exchange membranes (AEMs) exhibited higher maximum power densities than the commercial AEMs at 25 °C and 60 °C with humidified or non-humidified oxygen, demonstrating their potential for low-temperature direct ethanol fuel cell (DEFC) applications.

Influence of the electrocatalyst layer thickness on alkaline DEFC performance.

Determining the optimum layer thickness, for the anode and cathode, is of utmost importance for minimizing the costs of the alkaline direct ethanol fuel cell (DEFC) without lowering the electrochemical performance. In this study, the influence of layer thickness on the performance of the ethanol oxidation reaction (EOR) and oxygen reduction reaction (ORR) in an alkaline medium and resistance was investigated. The prepared gas diffusion electrodes (GDEs) were fully characterized, with scanning electron microscopy to determine the layer thickness and electrochemically in half-cell configuration. Cyclic voltammetry and polarization curve measurements were used to determine the oxidation and reduction processes of the metals, the electrochemical active surface area, and the activity towards the ORR and EOR. It was demonstrated that realistic reaction conditions can be achieved with simple and fast half-cell GDE measurements. Single cell measurements were conducted to evaluate the influence of factors, such as membrane or ethanol crossover. In addition, electrochemical impedance spectra investigation was performed to identify the effect of layer thickness on resistance. This successfully demonstrated that the optimal layer thicknesses and high maximum power density values (120 mW cm-2) were achieved with the Pt-free catalysts and membranes used.

Biomass Pyrolysis-Derived Biochar: A Versatile Precursor for Graphene Synthesis.

Graphene, a two-dimensional carbon allotrope with a honeycomb structure, has emerged as a material of immense interest in diverse scientific and technical domains. It is mainly produced from graphite by mechanical, chemical and electrochemical exfoliation. As renewable energy and source utilization increase, including bioenergy from forest and woody residues, processed, among other methods, by pyrolysis treatment, it can be expected that biochar production will increase too. Thus, its useful applications, particularly in obtaining high-added-value products, need to be fully explored. This study aims at presenting a comprehensive analysis derived from experimental data, offering insights into the potential of biomass pyrolysis-derived biochar as a versatile precursor for the controlled synthesis of graphene and its derivatives. This approach comprehended the highest energy output and lowest negative environmental footprint, including the minimization of both toxic gas emissions during processing and heavy metals' presence in the feedstock, toward obtaining biochar suitable to be modified, employing the Hummers and intercalation with persulfate salts methods, aiming at deriving graphene-like materials. Material characterization has revealed that besides morphology and structural features of the original wooden biomass, graphitized structures are present as well, which is proven clearly by Raman and XPS analyses. Electrochemical tests revealed higher conductivity in modified samples, implying their graphene-like nature.

Influence of the ultrasound cavitation intensity on reduced graphene oxide functionalization.

Graphene is a valuable and useful nanomaterial due to its exceptionally high tensile strength, electrical conductivity and transparency, as well as the ability to tune its materials properties via functionalization. One of the most important features needed to integrate functionalized graphene into products via scalable processing is the effectiveness of graphene dispersion in aqueous and organic solvents. In this study, we aimed to achieve the functionalization of reduced graphene oxide (rGO) by sonication in a one-step process using polyvinyl alcohol (PVA) as a model molecule to be bound to the rGO surface. We investigated the influence of the sonication energy on the efficacy of rGO functionalization. The correlation between the performance of the high-intensity ultrasonic horn and the synthesis of the PVA functionalized rGO was thoroughly investigated by TGA coupled with MS, and IR, Raman, XPS, Laser diffraction, and SEM analysis. The results show that the most soluble PVA-functionalized rGO is achieved at 50% of the ultrasonic horn amplitude. Analysis of cavitation dynamics revealed that in the near vicinity of the horn it is most aggressive at the highest amplitude (60%). This causes rGO flakes to break into smaller domains, which negatively affects the functionalization process. On the other hand, the maximum of the pressure pulsations far away from the horn is reached at 40% amplitude, as the pressure oscillations are attenuated significantly in the 2-phase flow region at higher amplitudes. These observations corelate well with the measured degree of functionalization, where the optimum functionalized rGO dispersion is reached at 50% horn amplitude, and generally imply that cavitation intensity must be carefully adjusted to achieve optimal rGO functionalization.

Improving Electroactivity of N-Doped Graphene Derivatives with Electrical Induction Heating.

Graphene derivatives doped with nitrogen have already been identified as active non-noble metal materials for oxygen reduction reaction (ORR) in PEM and alkaline fuel cells. However, an efficient and scalable method to prepare active, stable, and high-surface-area non-noble metal catalysts remains a challenge. Therefore, an efficient, potentially scalable strategy to improve the specific surface area of N-doped graphene derivatives needs to be developed. Here, we report a novel, rapid, and scalable electrical induction heating method for the preparation of N-doped heat-treated graphene oxide derivatives (N-htGOD) with a high specific surface area. The application of the induction heating method has been shown to shorten the reaction time and improve the energy efficiency of the process. The materials synthesized by induction heating exhibited very high specific surface area and showed improved ORR activity compared to the conventional synthesis method. Moreover, we demonstrated that the temperature program of induction heating could fine-tune the concentration of nitrogen functionalities. In particular, the graphitic-N configuration increases with increasing final temperature, in parallel with the increasing ORR activity. The presented results will contribute to the understanding and development of nonmetal N-htGOD for energy storage and conversion applications.

Ce-modified Co-Mn oxide spinel on reduced graphene oxide and carbon black as ethanol tolerant oxygen reduction electrocatalyst in alkaline media.

Electrocatalyst development for alkaline direct ethanol fuel cells is of great importance. In this context we have designed and synthesized cerium-modified cobalt manganese oxide (Ce-CMO) spinels on Vulcan XC72R (VC) and on its mixture with reduced graphene oxide (rGO). The influence of Ce modification on the activity and stability of the oxygen reduction reaction (ORR) in absence and presence of ethanol was investigated. The physicochemical characterization of Ce-CMO/VC and Ce-CMO/rGO-VC reveals CeO2 deposition and Ce doping of the CMO for both samples and a dissimilar morphology with respect to the nature of the carbon material. The electrochemical results display an enhanced ORR performance caused by Ce modification of CMO resulting in highly stable active sites. The Ce-CMO composites outperformed the CMO/VC catalyst with an onset potential of 0.89 V vs. RHE, a limiting current density of approx. -3 mA cm-2 and a remaining current density of 91% after 3600 s at 0.4 V vs. RHE. In addition, remarkable ethanol tolerance and stability in ethanol containing electrolyte compared to the commercial Pt/C catalyst was evaluated. These outstanding properties highlight Ce-CMO/VC and Ce-CMO/rGO-VC as promising, selective and ethanol tolerant ORR catalysts in alkaline media.

Synthesis of Optically and Redox Active Polyenaminones from Diamines and α,α'-Bis[(dimethylamino)methylidene]cyclohexanediones.

New oligo- and polyenaminones with Mw ~ 7-50 KDa were prepared in high yields by transaminative amino-enaminone polymerization of regioisomeric bis[(dimethylamino)methylidene]cyclohexanediones with alkylene and phenylenediamines. The polymers obtained are practically insoluble in aqueous and organic solvents and exhibit film-forming properties, UV light absorption at wavelengths below 500 nm, and redox activity. These properties indicate a promising application potential of these polymers, which could find use in optical and optoelectronic applications and in energy storage devices.

Correlating Structural Properties with Electrochemical Behavior of Non-graphitizable Carbons in Na-Ion Batteries.

We report on a detailed structural versus electrochemical property investigation of the corncob-derived non-graphitizable carbons prepared at different carbonization temperatures using a combination of structural characterization methodology unique to this field. Non-graphitizable carbons are currently the most viable option for the negative electrode in sodium-ion batteries. However, many challenges arise from the strong dependence of the precursor's choice and carbonization parameters on the evolution of the carbon matrix and its resulting electrochemistry. We followed structure development upon the increase in carbonization temperature with thorough structural characterization and electrochemical testing. With the increase of carbonization temperature from 900 to 1600 °C, our prepared materials exhibited a trend toward increasing structural order, an increase in the specific surface area of micropores, the development of ultramicroporosity, and an increase in conductivity. This was clearly demonstrated by a synergy of small- and wide-angle X-ray scattering, scanning transmission electron microscopy, and electron-energy loss spectroscopy techniques. Three-electrode full cell measurements confirmed incomplete desodiation of Na+ ions from the non-graphitizable carbons in the first cycle due to the formation of a solid-electrolyte interface and Na trapping in the pores, followed by a stable second cycle. The study of cycling stability over 100 cycles in a half-cell configuration confirmed the observed high irreversible capacity in the first cycle, which stabilized to a slow decrease afterward, with the Coulombic efficiency reaching 99% after 30 cycles and then stabilizing between 99.3 and 99.5%. Subsequently, a strong correlation between the determined structural properties and the electrochemical behavior was established.

Visible-Light Activation of Persulfate or H2O2 by Fe2O3/TiO2 Immobilized on Glass Support for Photocatalytic Removal of Amoxicillin: Mechanism, Transformation Products, and Toxicity Assessment.

Fe2O3/TiO2 nanocomposites were fabricated via a facile impregnation/calcination technique employing different amounts iron (III) nitrate onto commercial TiO2 (P25 Aeroxide). The as-prepared Fe2O3/TiO2 nanocomposites were characterized by X-ray diffraction (XRD), Raman spectroscopy (RS), scanning electron microscopy/energy-dispersive spectroscopy (SEM/EDXS), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller analysis (BET), electron impedance spectroscopy (EIS), photoluminescence spectroscopy (PL), and diffuse reflectance spectroscopy (DRS). As a result, 5% (w/w) Fe2O3/TiO2 achieved the highest photocatalytic activity in the slurry system and was successfully immobilized on glass support. Photocatalytic activity under visible-light irradiation was assessed by treating pharmaceutical amoxicillin (AMX) in the presence and absence of additional oxidants: hydrogen peroxide (H2O2) and persulfate salts (PS). The influence of pH and PS concentration on AMX conversion rate was established by means of statistical planning and response surface modeling. Results revealed optimum conditions of [S2O82-] = 1.873 mM and pH = 4.808; these were also utilized in presence of H2O2 instead of PS in long-term tests. The fastest AMX conversion possessing a zero-order rate constant of 1.51 × 10-7 M·min-1 was achieved with the photocatalysis + PS system. The AMX conversion pathway was established, and the evolution/conversion of formed intermediates was correlated with the changes in toxicity toward Vibrio fischeri. Reactive oxygen species (ROS) scavenging was also utilized to investigate the AMX conversion mechanism, revealing the major contribution of photogenerated h+ in all processes.