Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 12 de 12
Filtrar
Mais filtros

Base de dados
Tipo de documento
Intervalo de ano de publicação
1.
Nanotechnology ; 32(47)2021 Sep 01.
Artigo em Inglês | MEDLINE | ID: mdl-34388742

RESUMO

Different Ti substrates, such as particles (as-received and ball milled), plate and TEM grid were oxidized for the growth of one dimensional (1D) TiO2nanostructures. The Ti substrates were oxidized for 4 h at temperatures of 700 °C-750 °C in humid and dry Ar containing 5 ppm of O2. The effects of residual stress on the growth of 1D TiO2nanostructures were investigated. The residual stress inside the Ti particles was measured by XRD-sin2ψtechnique. The oxidized Ti substrates were characterized using field emission scanning electron microscope equipped with energy dispersive x-ray spectroscope, transmission electron microscope, x-ray diffractometer and x-ray photoelectron spectroscope. Results revealed that humid environment enhances the growth of 1D TiO2nanostructures. Four different types of 1D morphologies obtained during humid oxidation, e.g. stacked, ribbon, plateau and lamp-post shaped nanostructures. The presence of residual stress significantly enhances the density and coverage of 1D nanostructures. The as-grown TiO2nanostructures possess tetragonal rutile structure having length up to 10µm along the 〈1 0 1〉 directions. During initial stage of oxidation, a TiO2layer is formed on Ti substrate. Lower valence oxides (Ti3O5, Ti2O3and TiO) then form underneath the TiO2layer and induce stress at the interface of oxide layers. The induced stress plays significant role on the growth of 1D TiO2nanostructures. The induced stress is relaxed by creating new surfaces in the form of 1D TiO2nanostructures. A diffusion based model is proposed to explain the mechanism of 1D TiO2growth during humid oxidation of Ti. The 1D TiO2nanostructures and TiO2layer is formed by the interstitial diffusion of Ti4+ions to the surface and reacts with the surface adsorbed hydroxide ions (OH-). Lower valence oxides are formed at the metal-oxide interface by the reaction between diffused oxygen ions and Ti ions.

2.
Nanotechnology ; 31(17): 175603, 2020 Apr 24.
Artigo em Inglês | MEDLINE | ID: mdl-31918416

RESUMO

In this research work, nanowires were grown on brass (Cu - 37.2 wt% Zn) substrate by thermal oxidation. The substrate was oxidized at temperatures ranging from 350 °C to 600 °C in the presence of varying concentrations of O2 (1%-100%) in N2 flown at a rate of 200 sccm. The oxidized brass surface was characterized by field emission scanning electron microscope equipped with energy dispersive x-ray spectroscope and transmission electron microscope. Four different types of morphological variations such as thin, thick with branches, circular-flake and flat-cone shape nanostructures were observed during oxidation at different conditions. However, the prevalence of thin and thick morphology with branches was more prominent and found in all growth conditions. The length and diameter of the nanowires varied from 1 to 30 µm and 50 to 500 nm, respectively, whereas the length of the branches varied from 1 to 3 µm. The composition of the nanowires was ZnO possessing of hexagonal wurtzite structure. The selected area diffraction confirms that the nanowires grew along 〈1 1 [Formula: see text] 0〉 directions. Based on the results, a stress induced mechanism is proposed for the growth of ZnO nanowires on Cu - 37.2 wt% Zn substrate.

3.
Nanotechnology ; 31(42): 425503, 2020 Jun 29.
Artigo em Inglês | MEDLINE | ID: mdl-32599573

RESUMO

Tin (IV) oxide (SnO2) nanostructures are regarded as one of the most popular materials for conventional gas sensors, due to their high surface area and fast response in regard to most reducing and oxidizing gases. However, their high operating temperature (>200 °C) leads to high power consumption and limits their applications. Here, a new nanocomposite fiber materials, consisting of undoped and doped (nickel and palladium) SnO2 nanorods, polyaniline (PANI), and polyhydroxy-3-butyrate (P3HB) are synthesized via the hydrothermal method,followed by an in situ polymerization and electrospinning technique. The as-synthesized nanocomposites are tested using ethanol gas at different operating temperatures: 25 °C (room temperature), 60 °C, and 80 °C. The results reveal that all samples began to show a response at 80 °C. Pd:SnO2/PANI/P3HB nanocomposite fiber sensors demonstrate a relatively higher response than that of SnO2/PANI/P3HB and Ni:SnO2/PANI/P3HB nanocomposite sensors. At 80 °C , the Pd:SnO2/PANI/P3HB nanocomposite sensor records a response (R0/Rg ) of 1610, with a response time (Tres) of 90 s and a recovery time (Trec ) of 9 min in relation to 1000 ppm ethanol gas in N2. The sensor also displays a good level of response (R0/Rg = 200) at a low concentration level (50 ppm) of ethanol gas. Structural and chemical characterizations indicate that the ethanol gas sensing performance of Pd:SnO2/PANI/P3HB nanocomposite fibers can mainly be attributed to the p-n heterojunction, fiber geometry, and one-dimensional structure of SnO2 and to the presence of the Pd catalyst. This bio-nanocomposite fiber has the potential to be a breakthrough material in biodegradable low temperature ethanol sensing applications.

4.
Nanotechnology ; 28(26): 265702, 2017 Jun 30.
Artigo em Inglês | MEDLINE | ID: mdl-28593932

RESUMO

An ethanol gas sensor with enhanced sensor response was fabricated using Ni-doped SnO2 nanorods, synthesized via a simple hydrothermal method. It was found that the response (R = R 0/R g) of a 5.0 mol% Ni-doped SnO2 (5.0Ni:SnO2) nanorod sensor was 1.4 × 104 for 1000 ppm C2H5OH gas, which is about 13 times higher than that of pure SnO2 nanorods, (1.1 × 103) at the operating temperature of 450 °C. Moreover, for 50 ppm C2H5OH gas, the 5.0Ni:SnO2 nanorod sensor still recorded a significant response reading, namely 2.0 × 103 with a response time of 30 s and recovery time of 10 min. To investigate the effect of Ni dopant (0.5-5.0 mol%) on SnO2 nanorods, structural characterizations were demonstrated using field emission scanning electron microscopy, high-resolution transmission electron microscopy, Fourier transform infrared spectroscopy, x-ray diffraction (XRD) analysis, x-ray photoelectron spectroscopy and an ultraviolet-visible spectrometer. XRD results confirmed that all the samples consisted of tetragonal-shaped rutile SnO2 nanorods. It was found that the average diameter and length of the nanorods formed in 5.0Ni:SnO2 were four times smaller (∼6 and ∼35 nm, respectively) than those of the nanorods formed in pure SnO2 (∼25 and 150 nm). Interestingly, both samples had the same aspect ratio, ∼6. It is proposed that the high response of the 5.0Ni:SnO2 nanorod sensor can be attributed to the particle size, which causes an increase in the thickness of the charge depletion layer, and the presence of oxygen vacancies within the matrix of SnO2 nanorods.

5.
Sensors (Basel) ; 14(8): 13613-27, 2014 Jul 28.
Artigo em Inglês | MEDLINE | ID: mdl-25072346

RESUMO

In this research work, the sensitivity of TiO2 nanoparticles towards C2H5OH, H2 and CH4 gases was investigated. The morphology and phase content of the particles was preserved during sensing tests by prior heat treatment of the samples at temperatures as high as 750 °C and 1000 °C. Field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD) analysis were employed to characterize the size, morphology and phase content of the particles. For sensor fabrication, a film of TiO2 was printed on a Au interdigitated alumina substrate. The sensing temperature was varied from 450 °C to 650 °C with varying concentrations of target gases. Results show that the sensor has ultrahigh response towards ethanol (C2H5OH) compared to hydrogen (H2) and methane (CH4). The optimum sensing temperature was found to be 600 °C. The response and recovery times of the sensor are 3 min and 15 min, respectively, for 20 ppm C2H5OH at the optimum operating temperature of 600 °C. It is proposed that the catalytic action of TiO2 with C2H5OH is the reason for the ultrahigh response of the sensor.


Assuntos
Etanol/química , Nanopartículas/química , Titânio/química , Óxido de Alumínio/química , Temperatura Alta , Microscopia Eletrônica de Varredura/métodos , Microscopia Eletrônica de Transmissão/métodos , Difração de Raios X/métodos
6.
Sensors (Basel) ; 14(8): 14586-600, 2014 Aug 11.
Artigo em Inglês | MEDLINE | ID: mdl-25116903

RESUMO

An inexpensive single-step carbon-assisted thermal evaporation method for the growth of SnO2-core/ZnO-shell nanostructures is described, and the ethanol sensing properties are presented. The structure and phases of the grown nanostructures are investigated by field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD) techniques. XRD analysis indicates that the core-shell nanostructures have good crystallinity. At a lower growth duration of 15 min, only SnO2 nanowires with a rectangular cross-section are observed, while the ZnO shell is observed when the growth time is increased to 30 min. Core-shell hierarchical nanostructures are present for a growth time exceeding 60 min. The growth mechanism for SnO2-core/ZnO-shell nanowires and hierarchical nanostructures are also discussed. The sensitivity of the synthesized SnO2-core/ZnO-shell nanostructures towards ethanol sensing is investigated. Results show that the SnO2-core/ZnO-shell nanostructures deposited at 90 min exhibit enhanced sensitivity to ethanol. The sensitivity of SnO2-core/ZnO-shell nanostructures towards 20 ppm ethanol gas at 400 °C is about ~5-times that of SnO2 nanowires. This improvement in ethanol gas response is attributed to high active sensing sites and the synergistic effect of the encapsulation of SnO2 by ZnO nanostructures.


Assuntos
Etanol/química , Gases/química , Nanoestruturas/química , Compostos de Estanho/química , Óxido de Zinco/química , Desenho de Equipamento/métodos , Microscopia Eletrônica de Varredura/métodos , Nanofios/química , Tamanho da Partícula , Difração de Raios X/métodos
7.
Sensors (Basel) ; 12(6): 7207-58, 2012.
Artigo em Inglês | MEDLINE | ID: mdl-22969344

RESUMO

Recently one dimensional (1-D) nanostructured metal-oxides have attracted much attention because of their potential applications in gas sensors. 1-D nanostructured metal-oxides provide high surface to volume ratio, while maintaining good chemical and thermal stabilities with minimal power consumption and low weight. In recent years, various processing routes have been developed for the synthesis of 1-D nanostructured metal-oxides such as hydrothermal, ultrasonic irradiation, electrospinning, anodization, sol-gel, molten-salt, carbothermal reduction, solid-state chemical reaction, thermal evaporation, vapor-phase transport, aerosol, RF sputtering, molecular beam epitaxy, chemical vapor deposition, gas-phase assisted nanocarving, UV lithography and dry plasma etching. A variety of sensor fabrication processing routes have also been developed. Depending on the materials, morphology and fabrication process the performance of the sensor towards a specific gas shows a varying degree of success. This article reviews and evaluates the performance of 1-D nanostructured metal-oxide gas sensors based on ZnO, SnO(2), TiO(2), In(2)O(3), WO(x), AgVO(3), CdO, MoO(3), CuO, TeO(2) and Fe(2)O(3). Advantages and disadvantages of each sensor are summarized, along with the associated sensing mechanism. Finally, the article concludes with some future directions of research.

8.
Mater Sci Eng C Mater Biol Appl ; 118: 111228, 2021 Jan.
Artigo em Inglês | MEDLINE | ID: mdl-33254956

RESUMO

Organ repair, regeneration, and transplantation are constantly in demand due to various acute, chronic, congenital, and infectious diseases. Apart from traditional remedies, tissue engineering (TE) is among the most effective methods for the repair of damaged tissues via merging the cells, growth factors, and scaffolds. With regards to TE scaffold fabrication technology, polyurethane (PU), a high-performance medical grade synthetic polymer and bioactive material has gained significant attention. PU possesses exclusive biocompatibility, biodegradability, and modifiable chemical, mechanical and thermal properties, owing to its unique structure-properties relationship. During the past few decades, PU TE scaffold bioactive properties have been incorporated or enhanced with biodegradable, electroactive, surface-functionalised, ayurvedic products, ceramics, glass, growth factors, metals, and natural polymers, resulting in the formation of modified polyurethanes (MPUs). This review focuses on the recent advances of PU/MPU scaffolds, especially on the biomedical applications in soft and hard tissue engineering and regenerative medicine. The scientific issues with regards to the PU/MPU scaffolds, such as biodegradation, electroactivity, surface functionalisation, and incorporation of active moieties are also highlighted along with some suggestions for future work.


Assuntos
Poliuretanos , Engenharia Tecidual , Materiais Biocompatíveis/farmacologia , Polímeros , Alicerces Teciduais
9.
Sci Rep ; 11(1): 15768, 2021 Aug 03.
Artigo em Inglês | MEDLINE | ID: mdl-34344974

RESUMO

The miniaturization of electronic devices and the consequent decrease in the distance between conductive lines have increased the risk of short circuit failure due to electrochemical migration (ECM). The presence of ionic contaminants affects the ECM process. This work systematically investigates the ECM of tin (Sn) in the presence of bromide ions (Br-) in the range of 10-6 M to 1.0 M. Water drop test (WDT) was conducted in the two-probe semiconductor characterization system under an optical microscope as an in-situ observation. Polarization test was carried out to study the correlation between the corrosion properties of Sn and its ECM behaviour. The products of ECM were characterized by scanning electron microscope coupled with an energy dispersive X-rays spectrometer (SEM/EDX) and X-ray photoelectron spectrometer (XPS). The results confirm that the rate of anodic dissolution of Sn monotonously increases with the Br- concentration. However, the probability of ECM failure follows a normal distribution initially, but later increases with the Br- concentration. The main products of the ECM reactions are identified as Sn dendrites and tin hydroxide precipitates. The mechanisms of the ECM process of Sn in the presence of Br- are also suggested.

10.
Materials (Basel) ; 13(15)2020 Jul 24.
Artigo em Inglês | MEDLINE | ID: mdl-32722341

RESUMO

The use of graphene and its derivatives with excellent characteristics such as good electrical and mechanical properties and large specific surface area has gained the attention of researchers. Recently, novel nanocomposite materials based on graphene and conducting polymers including polyaniline (PANi), polypyrrole (PPy), poly (3,4 ethyldioxythiophene) (PEDOT), polythiophene (PTh), and their derivatives have been widely used as active materials in gas sensing due to their unique electrical conductivity, redox property, and good operation at room temperature. Mixing these two materials exhibited better sensing performance compared to pure graphene and conductive polymers. This may be attributed to the large specific surface area of the nanocomposites, and also the synergistic effect between graphene and conducting polymers. A variety of graphene and conducting polymer nanocomposite preparation methods such as in situ polymerization, electropolymerization, solution mixing, self-assembly approach, etc. have been reported and utilization of these nanocomposites as sensing materials has been proven effective in improving the performance of gas sensors. Review of the recent research efforts and developments in the fabrication and application of graphene and conducting polymer nanocomposites for gas sensing is the aim of this review paper.

11.
Materials (Basel) ; 9(7)2016 Jun 28.
Artigo em Inglês | MEDLINE | ID: mdl-28773645

RESUMO

Driven by the trends towards miniaturization in lead free electronic products, researchers are putting immense efforts to improve the properties and reliabilities of Sn based solders. Recently, much interest has been shown on low silver (Ag) content solder SAC105 (Sn-1.0Ag-0.5Cu) because of economic reasons and improvement of impact resistance as compared to SAC305 (Sn-3.0Ag-0.5Cu. The present work investigates the effect of minor aluminum (Al) addition (0.1-0.5 wt.%) to SAC105 on the interfacial structure between solder and copper substrate during reflow. The addition of minor Al promoted formation of small, equiaxed Cu-Al particle, which are identified as Cu3Al2. Cu3Al2 resided at the near surface/edges of the solder and exhibited higher hardness and modulus. Results show that the minor addition of Al does not alter the morphology of the interfacial intermetallic compounds, but they substantially suppress the growth of the interfacial Cu6Sn5 intermetallic compound (IMC) after reflow. During isothermal aging, minor alloying Al has reduced the thickness of interfacial Cu6Sn5 IMC but has no significant effect on the thickness of Cu3Sn. It is suggested that of atoms of Al exert their influence by hindering the flow of reacting species at the interface.

12.
Materials (Basel) ; 9(6)2016 May 31.
Artigo em Inglês | MEDLINE | ID: mdl-28773552

RESUMO

Miniaturization of electronic devices has led to the development of 3D IC packages which require ultra-small-scale interconnections. Such small interconnects can be completely converted into Cu-Sn based intermetallic compounds (IMCs) after reflow. In an effort to improve IMC based interconnects, an attempt is made to add Ni to Cu-Sn-based IMCs. Multilayer interconnects consisting of stacks of Cu/Sn/Cu/Sn/Cu or Cu/Ni/Sn/Ni/Sn/Cu/Ni/Sn/Ni/Cu with Ni = 35 nm, 70 nm, and 150 nm were electrodeposited sequentially using copper pyrophosphate, tin methanesulfonic, and nickel Watts baths, respectively. These multilayer interconnects were investigated under room temperature aging conditions and for solid-liquid reactions, where the samples were subjected to 250 °C reflow for 60 s and also 300 °C for 3600 s. The progress of the reaction in the multilayers was monitored by using X-ray Diffraction, Scanning Electron Microscope, and Energy dispersive X-ray Spectroscopy. FIB-milled samples were also prepared for investigation under room temperature aging conditions. Results show that by inserting a 70 nanometres thick Ni layer between copper and tin, premature reaction between Cu and Sn at room temperature can be avoided. During short reflow, the addition of Ni suppresses formation of Cu3Sn IMC. With increasing Ni thickness, Cu consumption is decreased and Ni starts acting as a barrier layer. On the other hand, during long reflow, two types of IMC were found in the Cu/Ni/Sn samples which are the (Cu,Ni)6Sn5 and (Cu,Ni)3Sn, respectively. Details of the reaction sequence and mechanisms are discussed.

SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA