Piezoelectric Sensor for the Monitoring of Arterial Pulse Wave: Detection of Arrhythmia Occurring in PAC/PVC Patients.

Previous studies have found that the non-invasive blood pressure measurement method based on the oscillometric method is inaccurate when an arrhythmia occurs. Therefore, we propose a high-sensitivity pulse sensor that can measure the hemodynamic characteristics of the pulse wave and then estimate the blood pressure. When an arrhythmia occurs, the hemodynamics of the pulse wave are abnormal and change the morphology of the pulse wave. Our proposed sensor can measure the occurrence of ectopic beats from the radial artery, and the detection algorithm can reduce the error of blood pressure estimation caused by the distortion of ectopic beats that occurs when the pulse wave is measured. In this study, we tested patients with premature atrial contraction (PAC) or premature ventricular contraction (PVC) and analyzed the morphology of the pulse waves when the sensor detected the ectopic beats. We discuss the advantages of using the Moens-Korteweg equation to estimate the blood pressure of patients with arrhythmia, which is different from the oscillometric method. Our research provides a possible arrhythmia detection method for wearable devices and can accurately estimate blood pressure in a non-invasive way during an arrhythmia.

A Novel Dentary Bone Conduction Device Equipped with Laser Communication in DSP.

In this study, we designed a dentary bone conduction system that transmits and receives audio by laser. The main objective of this research was to propose a complete hardware design method, including a laser audio transmitter and receiver and digital signal processor (DSP) based digital signal processing system. We also present a digital filter algorithm that can run on a DSP in real time. This experiment used the CMU ARCTIC databases' human-voice reading audio as the standard audio. We used a piezoelectric sensor to measure the vibration signal of the bone conduction transducer (BCT) and separately calculated the signal-to-noise ratio (SNR) of the digitally filtered audio output and the unfiltered audio output using DSP. The SNR of the former was twice that of the latter, and the BCT output quality significantly improved. From the results, we can conclude that the dentary bone conduction system integrated with a DSP digital filter enhances sound quality.

Preparation of insulating SiO2 nanostructured thin films by the sol-gel process.

Organic dispersion agents can effectively decrease the surface roughness of films. Here, films containing organic dispersion agents are used to produce metal-insulator-metal structures. It was found that addition of Triton caused films to become denser, and thicker, and the leak current of devices to decrease by 10 times compared with that without Triton because of its uniform dispersion in the films. The resulting films were used as the insulator layer of thin film transistors containing a semiconductor layer of evaporated pentacene. The interface between the insulator and semiconductor layers was found to affect the arrangement of pentacene, and O2 plasma was used to improve the interface activity to increase the order of the pentacene molecules and enhance the carrier mobility of the devices.

Design of multi-porous layer for dye-sensitized solar cells by doping with TiO2 nanoparticles.

We propose a multi-layer dye-sensitized solar cell (DSSC). Conventional DSSC components use a singular TiO2 particle size and a mono-layer active layer, but we demonstrate a multi-layer and multi-scale TiO2 particle based DSSC. Doping with large TiO2 particles can produce light scattering inside the DSSC component. Light scattering effects reduce TiO2 absorption at wavelengths of 200-300 nm. The unabsorbed light zig-zags between the Pt back electrode layer and the substrate, and enhances the Ru-dye absorption. To enhance the scattering, we doped the active layer with 20 wt% of large diameter TiO2. The multi-layer DSSC increases efficiency by about 15% compared with standard DSSCs.

A Hemodynamic Pulse Wave Simulator Designed for Calibration of Local Pulse Wave Velocities Measurement for Cuffless Techniques.

OBJECTIVE: Devices for cuffless blood pressure (BP) measurement have become increasingly widespread in recent years. Non-invasive continuous BP monitor (BPM) devices can diagnose potential hypertensive patients at an early stage; however, these cuffless BPMs require more reliable pulse wave simulation equipment and verification methods. Therefore, we propose a device to simulate human pulse wave signals that can test the accuracy of cuffless BPM devices using pulse wave velocity (PWV). METHODS: We design and develop a simulator capable of simulating human pulse waves comprising an electromechanical system to simulate the circulatory system and an arm model-embedded arterial phantom. These parts form a pulse wave simulator with hemodynamic characteristics. We use a cuffless device for measuring local PWV as the device under test to measure the PWV of the pulse wave simulator. We then use a hemodynamic model to fit the cuffless BPM and pulse wave simulator results; this model can rapidly calibrate the cuffless BPM's hemodynamic measurement performance. RESULTS: We first used multiple linear regression (MLR) to generate a cuffless BPM calibration model and then investigated differences between the measured PWV with and without MLR model calibration. The mean absolute error of the studied cuffless BPM without the MLR model is 0.77 m/s, which improves to 0.06 m/s when using the model for calibration. The measurement error of the cuffless BPM at BPs of 100-180 mmHg is 1.7-5.99 mmHg before calibration, which decreases to 0.14-0.48 mmHg after calibration. CONCLUSION: This study proposes a design of a pulse wave simulator based on hemodynamic characteristics and provides a standard performance verification method for cuffless BPMs that requires only MLR modeling on the cuffless BPM and pulse wave simulator. The pulse wave simulator proposed in this study can be used to quantitively assess the performance of cuffless BPMs. The proposed pulse wave simulator is suitable for mass production for the verification of cuffless BPMs. As cuffless BPMs become increasingly widespread, this study can provide performance testing standards for cuffless devices.

A novel smart photoelectric lock system: Speech transmitted by laser and speech to text.

We propose a circuit that modulates a speech signal to a laser, using which the speech signal can be transmitted using the laser. Also, it shows the use of a platform based on embedded ARM (Advanced RISC Machine), running a small deep learning model based on TDNN (Time delay neural network) and LSTM (Long short-term memory), and converting speech to text, and use the text cipher for unlocking. This research implements a smart lock system that can set a pre-record speech cipher and verify the similarity through a laser transmission speech cipher to unlock it. In our experiment result, the English speech of laser transmission can reach a WER (Word error rate) of 14.06% through the deep learning model to recognize the content of the speech cipher. We also design a similarity comparison algorithm based on LCS (Longest common subsequence) to compare the character set of the laser transmission speech compare and the prerecord speech cipher to calculate the similarity rate. Through the similarity comparison algorithm, when the WER is 27.27%, the male speech samples used in this study still have a 95% unlocking success rate, while the female speech samples have a 100% unlocking success rate. Compared with only using automatic speech recognition (ASR) to unlock, the method we propose is to compare the similarity of the content of speech cipher. The method significantly improves the unlocking fault tolerance of using lasers to transmit audio. Therefore, by using the laser to transmit the speech cipher, the usability of the photoelectric smart lock system has been significantly improved. At the same time, the characteristics of the laser are not easy to eavesdrop on the cipher, which can also improve security.

Assessment of a Calibration-Free Method of Cuffless Blood Pressure Measurement: A Pilot Study.

This study proposes a low-cost, high-sensitivity sensor of beat-to-beat local pulse wave velocity (PWV), to be used in a cuffless blood pressure monitor (BPM). OBJECTIVE: We design an adaptive algorithm to detect the feature of the pulse wave, making it possible for two sensors to measure the local PWV in the radial artery at a short distance. Unlike the cuffless BPM that needs to use a regression model for calibration. METHOD: We encapsulate the piezoelectric sensor material in a cavity and design an analog front-end circuit. This study used color ultrasound imaging equipment to measure radial arterial parameters, including the diameter and wall thickness, to aid the estimation of blood pressure (BP) using the Moens-Korteweg (MK) equation of hemodynamics. RESULTS: We compared the blood pressure estimated by the MK equation with the reference BP measured using an aneroid sphygmomanometer in a test group of 32 people, resulting in a mean difference of systolic BP of -0.63 mmHg, and a standard deviation of ±5.14 mmHg, a mean difference of mean arterial pressure (MAP) of 0.97 mmHg, with a standard deviation of ±3.54 mmHg, and a mean difference of diastolic BP of -1.14 mmHg, with a standard deviation of ±4.08 mmHg. This study has verified its compliance with ISO 81060-2. CONCLUSIONS: A new type of wearable continuous calibration-free BPM can replace the situation that requires the use of traditional ambulatory BPM and reduce patient discomfort. CLINICAL IMPACT: In this study can provide long-term continuous blood pressure monitoring in the hospital.

Application of Self-Assembled Polyarylether Substrate in Flexible Organic Light-Emitting Diodes.

The structure used in this study is as follows: substrate/PMMA/ZnS/Ag/MoO3/NPB/Alq3/LiF/Al. Here, PMMA serves as the surface flattening layer, ZnS/Ag/MoO3 as the anode, NPB as the hole injection layer, Alq3 as the emitting layer, LiF as the electron injection layer, and aluminum as the cathode. The properties of the devices with different substrates were investigated using P4 and glass, developed in the laboratory, as well as commercially available PET. After film formation, P4 creates holes on the surface. The light field distribution of the device was calculated at wavelengths of 480 nm, 550 nm, and 620 nm using optical simulation. It was found that this microstructure contributes to light extraction. The maximum brightness, external quantum efficiency, and current efficiency of the device at a P4 thickness of 2.6 µm were 72,500 cd/m2, 1.69%, and 5.68 cd/A, respectively. However, the maximum brightness of the same structure with PET (130 µm) was 9500 cd/m2. The microstructure of the P4 substrate was found to contribute to the excellent device performance through analysis of the AFM surface morphology, film resistance, and optical simulation results. The holes formed by the P4 substrate were created solely by spin-coating the material and then placing it on a heating plate to dry, without any special processing. To confirm the reproducibility of the naturally formed holes, devices were fabricated again with three different emitting layer thicknesses. The maximum brightness, external quantum efficiency, and current efficiency of the device at an Alq3 thickness of 55 nm were 93,400 cd/m2, 1.7%, and 5.6 cd/A, respectively.

An Arterial Compliance Sensor for Cuffless Blood Pressure Estimation Based on Piezoelectric and Optical Signals.

OBJECTIVE: Blood pressure (BP) data can influence therapeutic decisions for some patients, while non-invasive devices that continuously monitor BP can provide patients with a more comprehensive BP assessment. Therefore, this study proposes a multi-sensor-based small cuffless BP monitoring device that integrates a piezoelectric sensor array and an optical sensor, which can monitor the patient's physiological signals from the radial artery. METHOD: Based on the Moens-Korteweg (MK) equation of the hemodynamic model, pulse wave velocity (PWV) can be correlated with arterial compliance and BP can be estimated. Therefore, the novel method proposed in this study involves using a piezoelectric sensor array to measure the PWV and an optical sensor to measure the photoplethysmography (PPG) intensity ratio (PIR) signal to estimate the participant's arterial parameters. The parameters measured by multiple sensors were combined to estimate BP based on the P-ß model derived from the MK equation. RESULT: We recruited 20 participants for the BP monitoring experiment to compare the performance of the BP estimation method with the regression model and the P-ß model method with arterial compliance. We then compared the estimated BP with a reference device for validation. The results are presented as the error mean ± standard deviation (SD). Based on the regression model method, systolic blood pressure (SBP) was 0.32 ± 5.94, diastolic blood pressure (DBP) was 2.17 ± 6.22, and mean arterial pressure (MAP) was 1.55 ± 5.83. The results of the P-ß model method were as follows: SBP was 0.75 ± 3.9, DBP was 1.1 ± 3.12, and MAP was 0.49 ± 2.82. CONCLUSION: According to the results of our proposed small cuffless BP monitoring device, both methods of estimating BP conform to ANSI/AAMI/ISO 81060-2:20181_5.2.4.1.2 criterion 1 and 2, and using arterial parameters to calibrate the MK equation model can improve BP estimate accuracy. In the future, our proposed device can provide patients with a convenient and comfortable BP monitoring solution. Since the device is small, it can be used in a public place without attracting other people's attention, thereby effectively improving the patient's right to privacy, and increasing their willingness to use it.

Efficiency Analysis of Fuel Cell Components with Ionic Poly-Arylether Composite Membrane.

We use polyethylene glycol as an additive to explore how the hydrogen bonding of this additive changes the properties of SA8 blended sulfonated polyetheretherketone (SPEEK) composite films. We mixed a 5%wt polyethylene glycol solution into a 12.5%wt SA8 solution, and then prepared a film with a total weight of 40 g at a ratio of 1:99. The SA8 (PEG) solution was prepared and then mixed with 5%wt SPEEK solution, and a film-forming solution with a total weight of 8g in different mixing ratios was created. Polyethylene glycol (PEG) was mixed into the sulfonated polyarylether polymer SA8 to form physical cross-linking. Therefore, the sulfonated polyether ether ketone SPEEK was mixed in, and it exhibited good thermal stability and dimensional stability. However, there was some decrease in proton conductivity as the proportion of SPEEK increased. Although SPEEK mixed with sulfonated polymer reduces the proton conductivity, the physical cross-linking of PEG can improve the proton conductivity of the composite membrane, and adding SPEEK can not only solve the problem of the high sulfonation film swelling phenomenon, it can also improve the dimensional stability of the film through the hydrogen bonding force of PEG and obtain a composite film with excellent properties.

Electric Field-Assisted Filling of Sulfonated Polymers in ePTFE Backing Material for Fuel Cell.

This study fabricated a composite ePTFE-backed proton-exchange membrane by filling the pores on the ePTFE backing with sulfonated polyarylene ethers through an externally supplied electric field. The morphology changes were observed under an SEM. The results suggested that the application of an electric field had led to the effective filling of pores by polymers. In addition, the composite membrane featured good dimensional stability and swelling ratio, and its water uptake, proton conductivity and component efficiency increased with voltage. It is found in this study that the external application of an electric field resulted in the effective filling of pores in the ePTFE by sulfonated polyarylene ether polymers and, thus, an improved composite membrane performance.

Ionomer Membranes Produced from Hexaarylbenzene-Based Partially Fluorinated Poly(arylene ether) Blends for Proton Exchange Membrane Fuel Cells.

In this study, a series of high molecular weight ionomers of hexaarylbenzene- and fluorene-based poly(arylene ether)s were synthesized conveniently through condensation and post-sulfonation modification. The use a of blending method might increase the stacking density of chains and affect the formation both of interchain and intrachain proton transfer clusters. Multiscale phase separation caused by the dissolution and compatibility differences of blend ionomer in high-boiling-point solvents was examined through analysis and simulations. The blend membranes produced in this study exhibited a high proton conductivity of 206.4 mS cm−1 at 80 °C (increased from 182.6 mS cm−1 for precursor membranes), excellent thermal resistance (decomposition temperature > 200 °C), and suitable mechanical properties with a tensile strength of 73.8−77.4 MPa. As a proton exchange membrane for fuel cell applications, it exhibits an excellent power efficiency of approximately 1.3 W cm−2. Thus, the ionomer membranes have strong potential for use in proton exchange membrane fuel cells and other electrochemical applications.

Highly Proton-Conducting Membranes Based on Poly(arylene ether)s with Densely Sulfonated and Partially Fluorinated Multiphenyl for Fuel Cell Applications.

Series of partially fluorinated sulfonated poly(arylene ether)s were synthesized through nucleophilic substitution polycondensation from three types of diols and superhydrophobic tetra-trifluoromethyl-substituted difluoro monomers with postsulfonation to obtain densely sulfonated ionomers. The membranes had similar ion exchange capacities of 2.92 ± 0.20 mmol g-1 and favorable mechanical properties (Young's moduli of 1.60-1.83 GPa). The membranes exhibited considerable dimensional stability (43.1-122.3% change in area and 42.1-61.5% change in thickness at 80 °C) and oxidative stability (~55.5%). The proton conductivity of the membranes, higher (174.3-301.8 mS cm-1) than that of Nafion 211 (123.8 mS cm-1), was the percent conducting volume corresponding to the water uptake. The membranes were observed to comprise isolated to tailed ionic clusters of size 15-45 nm and 3-8 nm, respectively, in transmission electron microscopy images. A fuel cell containing one such material exhibited high single-cell performance-a maximum power density of 1.32 W cm2 and current density of >1600 mA cm-2 at 0.6 V. The results indicate that the material is a candidate for proton exchange membranes in fuel cell applications.