Resistive Chemosensors for the Detection of CO Based on Conducting Polymers and Carbon Nanocomposites: A Review.

Nanocomposite materials have seen increased adoption in a wide range of applications, with toxic gas detection, such as carbon monoxide (CO), being of particular interest for this review. Such sensors are usually characterized by the presence of CO absorption sites in their structures, with the Langmuir reaction model offering a good description of the reaction mechanism involved in capturing the gas. Among the reviewed sensors, those that combined polymers with carbonaceous materials showed improvements in their analytical parameters such as increased sensitivities, wider dynamic ranges, and faster response times. Moreover, it was observed that the CO reaction mechanism can differ when measured in mixtures with other gases as opposed to when it is detected in isolation, which leads to lower sensitivities to the target gas. To better understand such changes, we offer a complete description of carbon nanostructure-based chemosensors for the detection of CO from the sensing mechanism of each material to the water solution strategies for the composite nanomaterials and the choice of morphology for enhancing a layers' conductivity. Then, a series of state-of-the-art resistive chemosensors that make use of nanocomposite materials is analyzed, with performance being assessed based on their detection range and sensitivity.

A New Hybrid Sensitive PANI/SWCNT/Ferrocene-Based Layer for a Wearable CO Sensor.

Developing a sensing layer with high electroactive properties is an important aspect for proper functionality of a wearable sensor. The polymeric nanocomposite material obtained by a simple electropolymerization on gold interdigitated electrodes (IDEs) can be optimized to have suitable conductive properties to be used with direct current (DC) measurements. A new layer based on polyaniline:poly(4-styrenesulfonate) (PANI:PSS)/single-walled carbon nanotubes (SWCNT)/ferrocene (Fc) was electrosynthesized and deposed on interdigital transducers (IDT) and was characterized in detail using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoemission spectroscopy (XPS), and X-ray diffraction (XRD). The sensor characteristics of the material towards carbon monoxide (CO) in the concentration range of 10-300 ppm were examined, showing a minimal relative humidity interference of only 1% and an increase of sensitivity with the increase of CO concentration. Humidity interference could be controlled by the number of CV cycles when a compact layer was formed and the addition of Fc played an important role in the decrease of humidity. The results for CO detection can be substantially improved by optimizing the number of deposition cycles and enhancing the Fc concentration. The material was developed for selective detection of CO in real environmental conditions and shows good potential for use in a wearable sensor.

Modified Exfoliated Carbon Nanoplatelets as Sorbents for Ammonium from Natural Mineral Waters.

In this manuscript an improved sorbent based on modified exfoliated carbon nanoplatelets, applied in the removal of ammonium from aqueous samples, is presented. This sorbent showed better efficiency in comparison with the previous one obtained in our group for ammonium removal, the values of the maximum sorption capacity being improved from 10 to 12.04 mg/g. In terms of kinetics and sorption characteristic parameters, their values were also improved. Based on these results, a sorption mechanism was proposed, taking into account ion-exchange and chemisorption processes at the surface of the oxidized exfoliated carbon nanoplatelets. Future applications for simultaneous removal of other positive charged contaminants from natural waters might be possible.

An informative short-term study on the impacts of a triclocarban/weathered multi-walled carbon nanotube-adsorbed complex to benthic organisms.

Freshwater organisms are suitable models to study the fate of environmental pollutants. Due to their versatile and everyday use, many environmental pollutants such as triclocarban (TCC) or multi-walled carbon nanotubes (MWCNTs) enter environmental compartments very easily. TCC is known as a disinfectant and is declared as a highly aquatic toxicant. Multi-walled carbon nanotubes are used, e.g., in the automotive industry to improve plastic properties. Both TCCs and MWCNTs can pose major pollution hazards to various organisms. In addition, these substances can bind to each other due to their tendency to interact via strong hydrophobic interactions. Therefore, a short-term test was conducted to investigate the effects of the individual chemicals TCC and weathered MWCNTs (wMWCNTs) on a benthic biofilm and a grazing organism, Lymnaea stagnalis. Furthermore, the two compounds were coupled by an adsorption experiment resulting in a coupled complex formation (TCC + wMWCNTs). L. stagnalis showed no effects in terms of mortality. For benthic biofilm, the coupling test (TCC + wMWCNTs) showed a decrease of 58% in chlorophyll a (Chl-a) concentration. The main effect could be attributed to the wMWCNTs' exposure alone (decrease of 82%), but not to presence of TCC. The concentration range of Chl-a upon TCC exposure alone was comparable to that in the control group (32 and 37 µg/cm2). With respect to the particulate organic carbon (POC) concentration, very similar results were found for the solvent control, the TCC, and also for the TCC + wMWCNTs group (3, 2.9, and 2.9 mg/cm2). In contrast to the control, a significant increase in POC concentration (100%) was observed for wMWCNTs, but no synergistic effect of TCC + wMWCNTs was detected.

Non-Linear Regression Applied to the Sorption of Bisphenol A on Multi-Walled Carbon Nanotubes in Aqueous Systems.

In the present study, equilibrium parameters of adsorption of bisphenol A (BPA) on multi-walled carbon nanotubes were determined using non-linear Langmuir and Freundlich sorption models and regression methods were applied. In the calculations, some error functions were applied in the non-linear regression analysis, the best fit between the data being obtained, for a minimum error distribution. Non-linear regression analysis and the error distribution suggested Langmuir isotherm model the best one for estimation of equilibrium parameters. The results will be further used in environmental applications for BPA removal from natural waters, taking into account the spontaneous character of the adsorption process, the endocrine disrupting effect of BPA and the reduced toxicological effects of the impregnated sorbents.

Platform with biomimetic electrochemical sensors for adiponectin and leptin detection in human serum.

Two new biomimetic sensors for the detection of adiponectin (A) and leptin (L) through molecularly imprinted polymers (MIPs) onto gold working electrodes (GWEs) were fabricated. Based on electrochemical impedance spectroscopy (EIS) results and cyclic voltammetry (CV) characteristics recorded in the development stages of the fabricated sensors, the sensors were electrochemically optimized and used in an integrated microfluidic platform to detect adiponectin/leptin via conductance signals and non-imprinted electrodes were used as references. To overcome the limitation of the low response signals after template binding non-conductive polyphenol (PP) and poliscopoletin (PS) were used for templates formation. Under optimized experimental conditions the conductance and resistance signals were obtained in the linear range of 0-50 µg ml-1 for A and 1-32 ng∙ml-1 for L with low limits of detection (0.25 µg ml-1 for A and 0.110 ng ml-1 for L). The dedicated platform exhibited an excellent response with great selectivity and stability. Finally, the proposed biomimetic sensors were successfully applied to enable the determination of A and L in human patient's serum with very high accuracy when compared to enzyme-linked immunosorbent assay ELISA reference methods.

Adsorption of Sb (III) on Oxidized Exfoliated Graphite Nanoplatelets.

In this work, Sb (III) adsorption on oxidized exfoliated graphite nanoplatelets (ox-xGnP) was evaluated for the first time, to the best of our knowledge. The ox-xGnP were characterized by thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR), Brunauer⁻Emmet⁻Teller (BET) analysis, scanning electron microscopy (SEM), transmission electron microscopy (TEM) equipped with energy-dispersive X-ray spectroscopy (EDX), and Zeta potential analysis. The adsorption parameters, such as pH and contact time, were optimized, and the best adsorption capacity obtained was 8.91 mg g-1 at pH = 7.0, 1.0 mg ox-xGnP/100 mL solution, T = 293 K, 1.0 mg L-1, Sb (III), 25 min contact time. The best correlation of the kinetic data was described by a pseudo-first-order kinetic model, with R² = 0.999. The adsorption isotherms of Sb (III) onto ox-xGnP were best described by the Langmuir isotherm model. The thermodynamic parameters showed that the adsorption process was exothermic and spontaneous.