Noninvasive In-Situ Measurement of Blood Lactate Using Microwave Sensors.

GOAL: This paper reports a novel electromagnetic sensor technique for real-time noninvasive monitoring of blood lactate in human subjects. METHODS: The technique was demonstrated on 34 participants who undertook a cycling regime, with rest period before and after, to produce a rising and falling lactate response curve. Sensors attached to the arm and legs of participants gathered spectral data, blood samples were measured using a Lactate Pro V2; temperature and heart rate data was also collected. RESULTS: Pointwise mutual information and neural networks are used to produce a predictive model. The model shows a good correlation between the standard invasive and novel noninvasive electromagnetic wave based blood lactate measurements, with an error of 13.4% in the range of 0-12 mmol/L. CONCLUSION: The work demonstrates that electromagnetic wave sensors are capable of determining blood lactate level without the need for invasive blood sampling. SIGNIFICANCE: Measurement of blood metabolites, such as blood lactate, in real-time and noninvasively in hospital environments will reduce the risk of infection, increase the frequency of measurement and ensure timely intervention only when necessary. In sports, such tools will enhance training of athletes, and enable more effecting training regimes to be prescribed.

Development of polymer-based sensors for integration into a wireless data acquisition system suitable for monitoring environmental and physiological processes.

In this work, the pressure sensing properties of polyethylene (PE) and polyvinylidene fluoride (PVDF) polymer films were evaluated by integrating them with a wireless data acquisition system. Each device was connected to an integrated interface circuit, which includes a capacitance to frequency converter (C/F) and an internal voltage regulator to suppress supply voltage fluctuations on the transponder side. The system was tested under hydrostatic pressures ranging from 0 to 17 kPa. Results show PE to be the more sensitive to pressure changes, indicating that it is useful for the accurate measurement of pressure over a small range. On the other hand PVDF devices could be used for measurement over a wider range and should be considered due to the low hysteresis and good repeatability displayed during testing. It is thought that this arrangement could form the basis of a cost-effective wireless monitoring system for the evaluation of environmental or physiological processes.

A review of digestible microsystems for gastrointestinal tract diagnostic applications.

Present methods for investigation of the GI tract are invasive, distressing for the patient, and give a low diagnostic yield. Wireless, radio telemetry capsules, capable of monitoring physiological changes or visualizing the GI tract are noninvasive and could realize a faster time to diagnoses along with improved treatment of both organic diseases and functional disorders. Consequently, the patient's quality of life would improve. In this paper, early radiotelemetry capsules and the motivating factors for their development are discussed. Following this, prototype and commercially available digestible microsystems making use of microelectronics and microelectromechanical systems are presented. It is shown that these capsules have the potential to combine the functions of their predecessors and furthermore can be used for visualizing the gastrointestinal tract. These systems have the potential to improve diagnostic yield and, in the future, treatment of disease using these capsules should become a reality.

Review of the potential of a wireless MEMS and TFT microsystems for the measurement of pressure in the GI tract.

Telemetry capsules have existed since the 1950s and were used to measure temperature, pH or pressure inside the gastrointestinal (GI) tract. It was hoped that these capsules would replace invasive techniques in the diagnosis of function disorders in the GI tract. However, problems such as signal loss and uncertainty of the pills position limited their use in a clinical setting. In this paper, a review of the capabilities of MicroElectroMechanical Systems (MEMS) and thick film technology (TFT) for the fabrication of a wireless pressure sensing microsystem is presented. The circuit requirements and methods of data transfer are examined. The available fabrication methods for MEMS sensors are also discussed and examples of wireless sensors are given. Finally the limitations of each technology are examined.

The impact of heat treatment on interactions of contact-poled biphasic calcium phosphates with proteins and cells.

A number of studies have reported improved bone integration for calcium phosphate based materials electrically "poled" by an external electric field prior to implantation. In our study we investigated the effects of electrical polarization of a biphasic ceramic composed of 80% hydroxyapatite and 20% ß-tricalcium phosphate. As contact poling involves elevated temperatures as a prerequisite for inducing charge, we used two reference types: samples without any heat treatment and poling, and samples with no poling but heat treatment identical to that of the poled samples. All heat-treated samples (poled or unpoled) showed an improved wettability, which was attributed to a reduced hydrocarbon contamination. Heat treatment alone provoked an accelerated spreading of osteoblast-like cells, whereas on poled samples a retarded cell spreading was observed. While proliferation and several differentiation markers were not influenced by either heat treatment or poling, the release of proinflammatory cytokines interleukin-6 and -8 was significantly reduced for all heat-treated samples, irrespective of additional electrical poling. The study demonstrated that the behaviour of cells in contact with poled biphasic ceramics was influenced by two parameters: heating and charge. Our data revealed that heating of the calcium phosphate ceramics had a much more pronounced effect on cell behaviour than charge.