Synthesis of a highly recoverable 3D MnO2/rGO hybrid aerogel for efficient adsorptive separation of pharmaceutical residue.

Water contamination by non-steroidal anti-inflammatory drugs, such as acetaminophen, is an emerging ecological concern. In this study, a new three-dimensional manganese dioxide-engrafted reduced graphene oxide (3D MnO2/rGO) hybrid aerogel was developed for acetaminophen sequestration. The synthesis involved firstly the self-assembly of GO aerogel, followed by thermal reduction and in-situ MnO2 growth by redox-reaction. The aerogel demonstrated interlinked planes with smooth surfaces deposited with MnO2 nanospheres and pores of 138.4 - 235.3 µm width. The influences of adsorbent dosage, initial pH, acetaminophen concentration, temperature and contact time were investigated. It was determined that the adsorption of acetaminophen occurred on uniform sorption sites in the aerogel, as suggested by the best fit of data to the Langmuir isotherm, yielding a maximum adsorption capacity of 252.87 mg/g. This highest adsorption performance of the 3D MnO2/rGO aerogel was attained at a dosage of 0.6 g/L, initial pH of 6.2 and temperature of 40°C. The process kinetics were in-line with the pseudo-first-order and pseudo-second-order kinetics at 10 and 20 - 500 mg/L concentrations, respectively. Thermodynamic assay showed the spontaneity and endothermicity features of the 3D MnO2/rGO-acetaminophen system. The acetaminophen adsorption mechanisms were mainly hydrogen bonding and pore entrapment. Moreover, the as-synthesised aerogel was effectively regenerated using acetone and re-utilised in four adsorption-desorption cycles. Overall, the results highly recommend the implementation of the 3D MnO2/rGO hybrid aerogel for purification of wastewater polluted by acetaminophen residue.

Adsorptive decontamination of diclofenac by three-dimensional graphene-based adsorbent: Response surface methodology, adsorption equilibrium, kinetic and thermodynamic studies.

Pharmaceutical residues are emerging pollutants in the aquatic environment and their removal by conventional wastewater treatment methods has proven to be ineffective. This research aimed to develop a three-dimensional reduced graphene oxide aerogel (rGOA) for the removal of diclofenac in aqueous solution. The preparation of rGOA involved facile self-assembly of graphene oxide under a reductive environment of L-ascorbic acid. Characterisation of rGOA was performed by Fourier transform infrared, scanning electron microscope, transmission electron microscopy, nitrogen adsorption-desorption, Raman spectroscopy and X-ray diffraction. The developed rGOA had a measured density of 20.39 ±â€¯5.28 mg/cm3, specific surface area of 132.19 m2/g, cumulative pore volume of 0.5388 cm3/g and point of zero charge of 6.3. A study on the simultaneous interactions of independent factors by response surface methodology suggested dosage and initial concentration as the dominant parameters influencing the adsorption of diclofenac. The highest diclofenac adsorption capacity (596.71 mg/g) was achieved at the optimum conditions of 0.25 g/L dosage, 325 mg/L initial concentration, 200 rpm shaking speed and 30 °C temperature. The adsorption equilibrium data were best fitted to the Freundlich model with correlation coefficient (R2) varying from 0.9500 to 0.9802. The adsorption kinetic data were best correlated to the pseudo-first-order model with R2 ranging from 0.8467 to 0.9621. Thermodynamic analysis showed that the process was spontaneous (∆G = - 7.19 to - 0.48 kJ/mol) and exothermic (∆H = - 12.82 to - 2.17 kJ/mol). This research concluded that rGOA is a very promising adsorbent for the remediation of water polluted by diclofenac.

Environmental application of three-dimensional graphene materials as adsorbents for dyes and heavy metals: Review on ice-templating method and adsorption mechanisms.

The remediation of wastewater requires treatment technologies which are robust, efficient, simple to operate and affordable such as adsorption. Lately, three-dimensional (3D) graphene based materials have attracted significant attention as effective adsorbents for wastewater treatment. The intrinsic properties of 3D graphene structure such as large surface area and interconnected porous structure can facilitate the transport of pollutants into the 3D network and provide abundant active sites for trapping the pollutants. For the synthesis of 3D graphene structure, ice-templating is commonly practiced due to its facile steps, cost effectiveness and high scalability potential. This review covers the ice-templating fabrication technique for 3D graphene based materials and their application as adsorbents in eliminating dyes and heavy metals from aqueous media. The assembly mechanisms of the ice-templating fsynthesis are comprehensively discussed. Further discussion on the fundamental principles, critical process parameters and characteristics of ice-templated 3D graphene structures is also included. A thorough review on the mechanisms for batch adsorption of dyes and heavy metals is presented based on the structures and properties of the 3D graphene materials. The review further evaluates the dynamic adsorption in packed columns and the regeneration of 3D graphene based materials.

Facile synthesis of xanthan biopolymer integrated 3D hierarchical graphene oxide/titanium dioxide composite for adsorptive lead removal in wastewater.

Xanthan integrated graphene oxide functionalized by titanium dioxide was successfully prepared through facile, eco-friendly and cost effective ice-templating technique. The three-dimensional (3D) graphene composite demonstrated relatively high temperature stability, chemical functionalities and porous sponge-like structure. The adsorption of lead was favored by high initial concentration and shaking speed at the operational solution pH. The process equilibrium and kinetic adhered to the Langmuir and pseudo-second-order correlations, respectively. The biomass integrated graphene composite showed maximum adsorption capacities ranging from 132.18 to 199.22 mg/g for 30-70 °C. Moreover, it was highly regenerable under mild conditions (0.1 M hydrochloric acid, 30 °C) and used repeatedly while retaining 84.78% of its initial adsorption capacity at the fifth adsorption-regeneration cycle. With comparatively high lead adsorption capacities, adequate recyclability and environmentally friendliness, the as-prepared 3D graphene composite has high application potential in heavy metal-wastewater separation for protection of the environment and human health.

Ice-templated graphene oxide/chitosan aerogel as an effective adsorbent for sequestration of metanil yellow dye.

Graphene oxide/chitosan aerogel (GOCA) was prepared by a facile ice-templating technique without using any cross-linking reagent for metanil yellow dye sequestration. The adsorption performance of GOCA was investigated by varying the adsorbent mass, shaking speed, initial pH, contact time, concentration and temperature. The combined effects of adsorption parameters and the optimum conditions for dye removal were determined by response surface methodology. GOCA exhibited large removal efficiencies (91.5-96.4%) over a wide pH range (3-8) and a high adsorption capacity of 430.99 mg/g at 8 mg adsorbent mass, 400 mg/L concentration, 35.19 min contact time and 175 rpm shaking speed. The adsorption equilibrium was best represented by the Langmuir model. GOCA could be easily separated after adsorption and regenerated for re-use in 5 adsorption-desorption cycles thereby maintaining 80% of its adsorption capability. The relatively high adsorption and regeneration capabilities of GOCA render it an attractive adsorbent for treatment of azo dye-polluted water.

Effects of sonication on co-precipitation synthesis and activity of copper manganese oxide catalyst to remove methane and sulphur dioxide gases.

The utilisation of ultrasound in chemical preparation has been the focus of intense study in various fields, including materials science and engineering. This paper presents a novel method of synthesising the copper-manganese oxide (Hopcalite) catalyst that is used for the removal of volatile organic compounds and greenhouse gases like carbon monoxide. Several samples prepared under different conditions, with and without ultrasound, were subjected to a series of characterisation tests such as XRD, BET, FE-SEM, EDX, TPR-H2, TGA and FT-IR in order to establish their chemical and physical properties. A series of catalytic tests using a micro-reactor were subsequently performed on the samples in order to substantiate the aforementioned properties by analysing their ability to oxidise compressed natural gas (CNG), containing methane and sulphur dioxide. Results showed that ultrasonic irradiation of the catalyst led to observable alterations in its morphology: surfaces of the particles were noticeably smoothed and an increased in amorphicity was detected. Furthermore, ultrasonic irradiation has shown to enhance the catalytic activity of Hopcalite, achieving a higher conversion of methane relative to non-sonicated samples. Varying the ultrasonic intensity also produced appreciable effects, whereby an increase in intensity results in a higher conversion rate. The catalyst sonicated at the highest intensity of 29.7W/cm2 has a methane conversion rate of 13.5% at 400°C, which was the highest among all the samples tested.