Apply MIKE 11 model to study impacts of climate change on water resources and develop adaptation plan in the Mekong Delta, Vietnam: a case of Can Tho city.

Can Tho city in the Mekong Delta is in the top ten areas affected by climate change. Therefore, assessing climate change impacts, social and economic activities require proposed solutions to respond to climate change. This study aims to (i) apply the MIKE 11 model (Hydrodynamic module and Advection-Dispersion module) to simulate the impacts of climate change scenarios on water resources in Can Tho city; (ii) calculate water balance in Can Tho city; and (iii) suggest climate change adaptation plan for sustainable social-economic activities of the city. The results show that when the rainfall changes due to climate change, the flow rate tends to decrease at high tide and increase at low tide. When the sea level rises due to climate change, the flow rate tends to increase at high tide and decrease at low tide. For 2030, the flow will decrease up to 15.6% and 14.3% at the low tide period for RCP 2.6 and RCP 8.5 compared to the present, respectively. The flow will increase up to 63.5% and 58.9% at the high tide period for RCP 2.6 and RCP 8.5 compared to the present, respectively. The water demand evaluation shows that the water resource reserve in Can Tho city meets water demands in current and future scenarios under climate change. While rainwater and groundwater can provide enough water in the rainy season, the city has to use surface water during the dry season due to a lack of rainwater. Of these, agriculture contributes the most water demands (85%). Eight adaptation measures to climate change for Can Tho city are developed from 2021 to 2050.

Characteristics of Cu2O:Na Thin Films Prepared by DC Magnetron Sputtering Method at Low Temperature.

In this work, the success of doping Na into Cu2O thin films by reactive DC magnetron sputtering method at low temperature is described for the first time. The characteristics of crystal structure, morphology, optical, electrical properties and binding of elements in Cu2O:Na thin films are carefully investigated. The Cu2O:Na thin films have exhibited high electronic conductivity as p-type semiconductor and absorption in visible range. The highest hole concentration on the order of 1018 cm-3 and the lowest resistivity of 6.726 Ω · cm according to 6.56% Na impurities in Cu2O:Na lattice are also detected. The role of Na impurity in Cu2O structure is proposed that based on the changing of structure and alignment of elements.

Large-Area and Transferred High-Quality Three-Dimensional Topological Insulator Bi2-xSbxTe3-ySey Ultrathin Film by Catalyst-Free Physical Vapor Deposition.

Uniform and large-area synthesis of bulk insulating ultrathin films is an important subject toward applications of a surface of three-dimensional topological insulators (3D-TIs) in various electronic devices. Here we report epitaxial growth of bulk insulating three-dimensional topological insulator (3D-TI) Bi2-xSbxTe3-ySey (BSTS) ultrathin films, ranging from a few quintuple to several hundreds of layers, on mica in a large-area (1 cm2) via catalyst-free physical vapor deposition. These films can nondestructively be exfoliated using deionized water and transferred to various kinds of substrates as desired. The transferred BSTS thin films show good ambipolar characteristics as well as well-defined quantum oscillations arising from the topological surface states. The carrier mobility of 2500-5100 cm2/(V s) is comparable to the high-quality bulk BSTS single crystal. Moreover, tunable electronic states from the massless to the massive Dirac fermion were observed with a decrease in the film thickness. Both the feasible large-area synthesis and the reliable film transfer process can promise that BSTS ultrathin films will pave a route to many applications of 3D-TIs.

Facile Preparation Method of TiO2/Activated Carbon for Photocatalytic Degradation of Methylene Blue.

The development of nanocomposite photocatalysts with high photocatalytic activity, cost-effectiveness, a simple preparation process, and scalability for practical applications is of great interest. In this study, nanocomposites of TiO2 Degussa P25 nanoparticles/activated carbon (TiO2/AC) were prepared at various mass ratios of (4:1), (3:2), (2:3), and (1:4) by a facile process involving manual mechanical pounding, ultrasonic-assisted mixing in an ethanol solution, paper filtration, and mild thermal annealing. The characterization methods included XRD, SEM-EDS, Raman, FTIR, XPS, and UV-Vis spectroscopies. The effects of TiO2/AC mass ratios on the structural, morphological, and photocatalytic properties were systematically studied in comparison with bare TiO2 and bare AC. TiO2 nanoparticles exhibited dominant anatase and minor rutile phases and a crystallite size of approximately 21 nm, while AC had XRD peaks of graphite and carbon and a crystallite size of 49 nm. The composites exhibited tight decoration of TiO2 nanoparticles on micron-/submicron AC particles, and uniform TiO2/AC composites were obtained, as evidenced by the uniform distribution of Ti, O, and C in an EDS mapping. Moreover, Raman spectra show the typical vibration modes of anatase TiO2 (e.g., E1g(1), B1g(1), Eg(3)) and carbon materials with D and G bands. The TiO2/AC with (4:1), (3:2), and (2:3) possessed higher reaction rate constants (k) in photocatalytic degradation of methylene blue (MB) than that of either TiO2 or AC. Among the investigated materials, TiO2/AC = 4:1 achieved the highest photocatalytic activity with a high k of 55.2 × 10-3 min-1 and an MB removal efficiency of 96.6% after 30 min of treatment under UV-Vis irradiation (120 mW/cm2). The enhanced photocatalytic activity for TiO2/AC is due to the synergistic effect of the high adsorption capability of AC and the high photocatalytic activity of TiO2. Furthermore, TiO2/AC promotes the separation of photoexcited electron/hole (e-/h+) pairs to reduce their recombination rate and thus enhance photocatalytic activity. The optimal TiO2/AC composite with a mass ratio of 4/1 is suggested for treating industrial or household wastewater with organic pollutants.

Clinical Features and Treatment Outcomes of COVID-19 Admissions in the Can Tho City Hospital of Tuberculosis and Respiratory Diseases, Vietnam: A Hospital-Based Observational Study.

BACKGROUND: Coronavirus disease 2019 (COVID-19), caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection, is among the top global health crises. As confirmed by the Vietnam Ministry of Health on 25th January 2023, Vietnam had a cumulative total of more than 11.52 million COVID-19 patients, including 10.61 million recoveries and 43,186 deaths. OBJECTIVES: This study aimed to describe the clinical and subclinical characteristics, treatment progress, and outcomes of 310 cases of SARS-CoV-2 infection. METHODS: A total of 310 patients with medical records of SARS-CoV-2 were admitted to Can Tho City Hospital of Tuberculosis and Lung Diseases, Can Tho city, Vietnam, between July 2021 and December 2021. Demographic and clinical data, including laboratory examinations, of all the patients were collected and analyzed. RESULTS: The median duration of hospital stay was 16.4 ± 5.3 days. There were 243 (78.4%) patients with clinical symptoms of COVID-19 and 67 (21.6%) patients without clinical symptoms. The common symptoms included cough (71.6% of 310 patients), fever (35.4%), shortness of breath (22.6%), sore throat (21.4%), loss of smell/taste (15.6%), and diarrhea (14.4%). Regarding treatment outcomes, 92.3% of the patients were discharged from the hospital, 1.9% of the patients suffered a more severe illness and were transferred to a higher-level hospital, and 5.8% of the patients died. The RT-PCR results were negative in 55.2% of the patients, and 37.1% of the patients had positive RT-PCR results with Ct values of >30 on the discharge/transfer day. Multivariate logistic regression analyses showed that comorbidity and decreased blood pH were statistically significantly related to the treatment outcomes of the patients with COVID-19 (p < 0.05). CONCLUSIONS: This study provides useful information (i.e., the clinical characteristics and treatment outcomes) on the COVID-19 pandemic in Vietnam during its biggest outbreak; the information may be used for reference and for making improvements in the handling of future health crises.

Effects of Oxygen Pressure on the Microstructures and Nanomechanical Properties of Samarium-Doped BiFeO3 Thin Films.

In this study, samarium (Sm-10at%)-doped BiFeO3 (SmBFO) thin films were grown on platinum-coated glass substrates using pulsed laser deposition (PLD) to unveil the correlation between the microstructures and nanomechanical properties of the films. The PLD-derived SmBFO thin films were prepared under various oxygen partial pressures (PO2) of 10, 30, and 50 mTorr at a substrate temperature of 600 °C. The scanning electron microscopy analyses revealed a surface morphology consisting of densely packed grains, although the size distribution varied with the PO2. X-ray diffraction results indicate that all SmBFO thin films are textured and preferentially oriented along the (110) crystallographic orientation. The crystallite sizes of the obtained SmBFO thin films calculated from the Scherrer and (Williamson-Hall) equations increased from 20 (33) nm to 25 (52) nm with increasing PO2. In addition, the nanomechanical properties (the hardness and Young's modulus) of the SmBFO thin films were measured by using nanoindentation. The relationship between the hardness and crystalline size of SmBFO thin films appears to closely follow the Hall-Petch equation. In addition, the PO2 dependence of the film microstructure, the crystallite size, the hardness, and Young's modulus of SmBFO thin films are discussed.

Development of a Scalable Process of Film-Coated bi-Layer Tablet Containing Sustained-Release Metoprolol Succinate and Immediate-Release Amlodipine Besylate.

The development of new drugs that combine active ingredients for the treatment hypertension is critically essential owing to its offering advantages for both patients and manufacturers. In this study, for the first time, detailed development of a scalable process of film-coated bi-layer tablets containing sustained-release metoprolol succinate and immediate-release amlodipine besylate in a batch size of 10,000 tablets is reported. The processing parameters of the manufacturing process during dry mixing-, drying-, dry mixing- completion stages were systematically investigated, and the evaluation of the film-coated bi-layer tablet properties was well established. The optimal preparation conditions for metoprolol succinate layer were 6 min- dry mixing with a high-speed mixer (120 rpm and 1400 rpm), 30-min drying with a fluid bed dryer, and 5-min- mixing completion at 25 rpm. For the preparation of amlodipine besylate layer, the optimal dry-mixing time using a cube mixer (25 rpm) was found to be 5 min. The average weight of metoprolol succinate layers and bi-layer tablets were controlled at 240-260 mg and 384-416 mg, respectively. Shewhart R chart and X¯ charts of all three sampling lots were satisfactory, confirming that the present scalable process was stable and successful. This study confirms that the manufacturing process is reproducible, robust; and it yields a consistent product that meets specifications.

TiO2 and Au-TiO2 Nanomaterials for Rapid Photocatalytic Degradation of Antibiotic Residues in Aquaculture Wastewater.

Antibiotic residues in aquaculture wastewater are considered as an emerging environmental problem, as they are not efficiently removed in wastewater treatment plants. To address this issue, we fabricated TiO2 nanotube arrays (TNAs), TiO2 nanowires on nanotube arrays (TNWs/TNAs), Au nanoparticle (NP)-decorated-TNAs, and TNWs/TNAs, which were applied for assessing the photocatalytic degradation of eight antibiotics, simultaneously. The TNAs and TNWs/TNAs were synthesized by anodization using an aqueous NH4F/ethylene glycol solution. Au NPs were synthesized by chemical reduction method, and used to decorate on TNAs and TNWs/TNAs. All the TiO2 nanostructures exhibited anatase phase and well-defined morphology. The photocatalytic performance of TNAs, TNWs/TNAs, Au-TNAs and Au-TNWs/TNAs was studied by monitoring the degradation of amoxicillin, ampicillin, doxycycline, oxytetracycline, lincomycin, vancomycin, sulfamethazine, and sulfamethoxazole under ultraviolet (UV)-visible (VIS), or VIS illumination by LC-MS/MS method. All the four kinds of nanomaterials degraded the antibiotics effectively and rapidly, in which most antibiotics were removed completely after 20 min treatment. The Au-TNWs/TNAs exhibited the highest photocatalytic activity in degradation of the eight antibiotics. For example, reaction rate constants of Au-TNWs/TNAs for degradation of lincomycin reached 0.26 min-1 and 0.096 min-1 under UV-VIS and VIS irradiation, respectively; and they were even higher for the other antibiotics. The excellent photocatalytic activity of Au-TNWs/TNAs was attributed to the synergistic effects of: (1) The larger surface area of TNWs/TNAs as compared to TNAs, and (2) surface plasmonic effect in Au NPs to enhance the visible light harvesting.

Nanomechanical and Material Properties of Fluorine-Doped Tin Oxide Thin Films Prepared by Ultrasonic Spray Pyrolysis: Effects of F-Doping.

Fluorine-doped tin oxide (FTO) thin films were deposited on glass substrates using ultrasonic spray pyrolysis (USP) at a fixed substrate temperature of 400 °C and various Fluorine/Tin (F/Sn) atomic ratios of 0, 0.1, 0.5, and 1.0. Effects of F/Sn atomic ratios on structural-morphological, compositional, electrical, optical, and nanomechanical properties of the FTO thin films were systematically studied. The FTO films exhibited a tetragonal structure with preferred orientations of (110), (200), and (211), and polycrystalline morphology with spear-like or coconut shell-like particles on the surfaces. The presence of F-doping was confirmed by XPS results with clear F1s peaks, and F-concentration was determined to be 0.7% for F/Sn = 0.1 and 5.1% for F/Sn = 0.5. Moreover, the resistivity of FTO films reduced remarkably from 4.1 mΩcm at F/Sn = 0 to 0.7 mΩcm at F/Sn = 1, primarily due to the corresponding increase of carrier concentration from 2 × 1020 cm-3 to 1.2 × 1021 cm-3. The average optical transmittance of the films prepared at F/Sn of 0-0.5 was over 90%, and it decreased to 84.4% for the film prepared at F/Sn = 1. The hardness (H) and Young's modulus (E) of the FTO films increased when the F/Sn ratios increased from 0 to 0.5, reaching maximum values of H = 12.3 ± 0.4 GPa, E = 131.7 ± 8.0 GPa at F/Sn = 0.5. Meanwhile, the H and E reduced considerably when the F/Sn ratio further increased to 1.0, following the inverse Hall-Petch effect approximately, suggesting that the grain boundary effect played a primary role in manipulating the nanomechanical properties of the FTO films. Furthermore, favorable mechanical properties with large H/Ef and H 3 / E f 2 ratios were found for the FTO film prepared at F/Sn = 0.5, which possessed high crystallinity, large grain size, and compact morphology.

Localized Deformation and Fracture Behaviors in InP Single Crystals by Indentation.

The indentation-induced deformation mechanisms in InP(100) single crystals were investigated by using nanoindentation and cross-sectional transmission electron microscopy (XTEM) techniques. The results indicated that there were multiple "pop-in" events randomly distributed in the loading curves, which were conceived to arise primarily from the dislocation nucleation and propagation activities. An energetic estimation on the number of nanoindentation-induced dislocations associated with pop-in effects is discussed. Furthermore, the fracture patterns were performed by Vickers indentation. The fracture toughness and the fracture energy of InP(100) single crystals were calculated to be around 1.2 MPa·m1/2 and 14.1 J/m², respectively.

Nanoindentation of Bi2Se3 Thin Films.

The nanomechanical properties and nanoindentation responses of bismuth selenide (Bi2Se3) thin films are investigated in this study. The Bi2Se3 thin films are deposited on c-plane sapphire substrates using pulsed laser deposition. The microstructural properties of Bi2Se3 thin films are analyzed by means of X-ray diffraction (XRD). The XRD results indicated that Bi2Se3 thin films are exhibited the hexagonal crystal structure with a c-axis preferred growth orientation. Nanoindentation results showed the multiple "pop-ins" displayed in the loading segments of the load-displacement curves, suggesting that the deformation mechanisms in the hexagonal-structured Bi2Se3 films might have been governed by the nucleation and propagation of dislocations. Further, an energetic estimation of nanoindentation-induced dislocation associated with the observed pop-in effects was made using the classical dislocation theory.

Enhanced Photocatalytic Performance of Nitrogen-Doped TiO2 Nanotube Arrays Using a Simple Annealing Process.

Nitrogen-doped TiO2 nanotube arrays (N-TNAs) were successfully fabricated by a simple thermal annealing process in ambient N2 gas at 450 °C for 3 h. TNAs with modified morphologies were prepared by a two-step anodization using an aqueous NH4F/ethylene glycol solution. The N-doping concentration (0⁻9.47 at %) can be varied by controlling N2 gas flow rates between 0 and 500 cc/min during the annealing process. Photocatalytic performance of as-prepared TNAs and N-TNAs was studied by monitoring the methylene blue degradation under visible light (λ ≥ 400 nm) illumination at 120 mW·cm-2. N-TNAs exhibited appreciably enhanced photocatalytic activity as compared to TNAs. The reaction rate constant for N-TNAs (9.47 at % N) reached 0.26 h-1, which was a 125% improvement over that of TNAs (0.115 h-1). The significant enhanced photocatalytic activity of N-TNAs over TNAs is attributed to the synergistic effects of (1) a reduced band gap associated with the introduction of N-doping states to serve as carrier reservoir, and (2) a reduced electron‒hole recombination rate.

Ultrasonic-assisted cathodic electrochemical discharge for graphene synthesis.

We present a novel and highly efficient method for exfoliating of graphite to produce graphene via the synergistic effects of in-situ plasma induced electrochemical exfoliation with ultrasonic energy, called ultrasonic-assisted cathodic electrochemical discharge. This method can work at moderate temperatures without the need of acidic media or expensive ionic electrolyte. The produced graphene exhibited a large lateral dimension of approximately 6µm and a thickness of 2.5nm, corresponding to approximately seven layers of graphene. An exfoliating mechanism of graphite to produce graphene sheets is also proposed in this study.