Efficient, stable and scalable perovskite solar cells using poly(3-hexylthiophene).

Perovskite solar cells typically comprise electron- and hole-transport materials deposited on each side of a perovskite active layer. So far, only two organic hole-transport materials have led to state-of-the-art performance in these solar cells1: poly(triarylamine) (PTAA)2-5 and 2,2',7,7'-tetrakis(N,N-di-p-methoxyphenylamine)-9,9'-spirobifluorene (spiro-OMeTAD)6,7. However, these materials have several drawbacks in terms of commercialization, including high cost8, the need for hygroscopic dopants that trigger degradation of the perovskite layer9 and limitations in their deposition processes10. Poly(3-hexylthiophene) (P3HT) is an alternative hole-transport material with excellent optoelectronic properties11-13, low cost8,14 and ease of fabrication15-18, but so far the efficiencies of perovskite solar cells using P3HT have reached only around 16 per cent19. Here we propose a device architecture for highly efficient perovskite solar cells that use P3HT as a hole-transport material without any dopants. A thin layer of wide-bandgap halide perovskite is formed on top of the narrow-bandgap light-absorbing layer by an in situ reaction of n-hexyl trimethyl ammonium bromide on the perovskite surface. Our device has a certified power conversion efficiency of 22.7 per cent with hysteresis of ±0.51 per cent; exhibits good stability at 85 per cent relative humidity without encapsulation; and upon encapsulation demonstrates long-term operational stability for 1,370 hours under 1-Sun illumination at room temperature, maintaining 95 per cent of the initial efficiency. We extend our platform to large-area modules (24.97 square centimetres)-which are fabricated using a scalable bar-coating method for the deposition of P3HT-and achieve a power conversion efficiency of 16.0 per cent. Realizing the potential of P3HT as a hole-transport material by using a wide-bandgap halide could be a valuable direction for perovskite solar-cell research.

Carrier-resolved photo-Hall effect.

The fundamental parameters of majority and minority charge carriers-including their type, density and mobility-govern the performance of semiconductor devices yet can be difficult to measure. Although the Hall measurement technique is currently the standard for extracting the properties of majority carriers, those of minority carriers have typically only been accessible through the application of separate techniques. Here we demonstrate an extension to the classic Hall measurement-a carrier-resolved photo-Hall technique-that enables us to simultaneously obtain the mobility and concentration of both majority and minority carriers, as well as the recombination lifetime, diffusion length and recombination coefficient. This is enabled by advances in a.c.-field Hall measurement using a rotating parallel dipole line system and an equation, ΔµH = d(σ2H)/dσ, which relates the hole-electron Hall mobility difference (ΔµH), the conductivity (σ) and the Hall coefficient (H). We apply this technique to various solar absorbers-including high-performance lead-iodide-based perovskites-and demonstrate simultaneous access to majority and minority carrier parameters and map the results against varying light intensities. This information, which is buried within the photo-Hall measurement1,2, had remained inaccessible since the original discovery of the Hall effect in 18793. The simultaneous measurement of majority and minority carriers should have broad applications, including in photovoltaics and other optoelectronic devices.

Defect Engineering of Metal Halide Perovskite Nanocrystals via Spontaneous Diffusion of Ag Nanocrystals.

Perovskite nanocrystals (NCs) have emerged as a promising building block for the fabrication of optic-/optoelectronic-/electronic devices owing to their superior characteristics, such as high absorption coefficient, rapid ion mobilities, and tunable energy levels. However, their low structural stability and poor surface passivation have restricted their application to next-generation devices. Herein, a drug delivery system (DDS)-inspired post-treatment strategy is reported for improving their structural stability by doping of Ag into CsPbBr3 (CPB) perovskite NCs; delivery to damaged sites can promote their structural recovery slowly and uniformly, averting the permanent loss of their intrinsic characteristics. Ag NCs are designed through surface-chemistry tuning and structural engineering to enable their circulation in CPB NC dispersions, followed by their delivery to the CPB NC surface, defect-site recovery, and defect prevention. The perovskite-structure healing process through the DDS-type process (with Ag NCs as the drug) is analyzed by a combination of theoretical calculations (with density functional theory) and experimental analyses. The proposed DDS-inspired healing strategy significantly enhances the optical properties and stability of perovskite NCs, enabling the fabrication of white light-emitting diodes.

Efficient vertical charge transport in polycrystalline halide perovskites revealed by four-dimensional tracking of charge carriers.

Fast diffusion of charge carriers is crucial for efficient charge collection in perovskite solar cells. While lateral transient photoluminescence microscopies have been popularly used to characterize charge diffusion in perovskites, there exists a discrepancy between low diffusion coefficients measured and near-unity charge collection efficiencies achieved in practical solar cells. Here, we reveal hidden microscopic dynamics in halide perovskites through four-dimensional (directions x, y and z and time t) tracking of charge carriers by characterizing out-of-plane diffusion of charge carriers. By combining this approach with confocal microscopy, we discover a strong local heterogeneity of vertical charge diffusivities in a three-dimensional perovskite film, arising from the difference between intragrain and intergrain diffusion. We visualize that most charge carriers are efficiently transported through the direct intragrain pathways or via indirect detours through nearby areas with fast diffusion. The observed anisotropy and heterogeneity of charge carrier diffusion in perovskites rationalize their high performance as shown in real devices. Our work also foresees that further control of polycrystal growth will enable solar cells with micrometres-thick perovskites to achieve both long optical path length and efficient charge collection simultaneously.

Environmental impact of metal halide perovskite solar cells and potential mitigation strategies: A critical review.

Metal halide perovskite solar cells (PSCs) have gained extensive attention in the field of solar photovoltaic technology over the past few years. Despite being a remarkable alternative to fossil fuels, solar cells may have detrimental effects on the environment and human health owing to the use of toxic materials during manufacturing. Although modern metal-halide-based PSCs are stable and have encapsulation to prevent the release of potentially toxic materials into the environment, their destruction due to strong winds, hail, snow, landslides, fires, or waste disposal can result in the exposure of these materials to the environment. This may lead to the contamination of soil and groundwater, and uptake of potentially toxic elements by plants, subsequently affecting humans and other living organisms via food chain contamination. Despite worldwide concern, the environmental and ecotoxicological impacts of metal-halide-based PSCs have not been comprehensively surveyed. This review summarizes and critically evaluates the current status of metal-halide-based PSC production and its impact on environmental sustainability, food security, and human health. Furthermore, safe handling and disposal methods for the waste generated from metal-halide-based PSCs are proposed, with a focus on recycling and reuse. Although some studies have suggested that the amount of lead released from metal halide PSCs is far below the maximum permissible levels in most soils, a clear conclusion cannot be reached until real contamination scenarios are assessed under field conditions. Precautions must be taken to minimize environmental contamination throughout the lifecycle of PSCs until nontoxic and similarly performing alternative solar photovoltaic products are developed.

Compositional engineering of perovskite materials for high-performance solar cells.

Of the many materials and methodologies aimed at producing low-cost, efficient photovoltaic cells, inorganic-organic lead halide perovskite materials appear particularly promising for next-generation solar devices owing to their high power conversion efficiency. The highest efficiencies reported for perovskite solar cells so far have been obtained mainly with methylammonium lead halide materials. Here we combine the promising-owing to its comparatively narrow bandgap-but relatively unstable formamidinium lead iodide (FAPbI3) with methylammonium lead bromide (MAPbBr3) as the light-harvesting unit in a bilayer solar-cell architecture. We investigated phase stability, morphology of the perovskite layer, hysteresis in current-voltage characteristics, and overall performance as a function of chemical composition. Our results show that incorporation of MAPbBr3 into FAPbI3 stabilizes the perovskite phase of FAPbI3 and improves the power conversion efficiency of the solar cell to more than 18 per cent under a standard illumination of 100 milliwatts per square centimetre. These findings further emphasize the versatility and performance potential of inorganic-organic lead halide perovskite materials for photovoltaic applications.

Rational Strategies for Efficient Perovskite Solar Cells.

A long-standing dream in the large scale application of solar energy conversion is the fabrication of solar cells with high-efficiency and long-term stability at low cost. The realization of such practical goals depends on the architecture, process and key materials because solar cells are typically constructed from multilayer heterostructures of light harvesters, with electron and hole transporting layers as a major component. Recently, inorganic-organic hybrid lead halide perovskites have attracted significant attention as light absorbers for the fabrication of low-cost and high-efficiency solar cells via a solution process. This mainly stems from long-range ambipolar charge transport properties, low exciton binding energies, and suitable band gap tuning by managing the chemical composition. In our pioneering work, a new photovoltaic platform for efficient perovskite solar cells (PSCs) was proposed, which yielded a high power conversion efficiency (PCE) of 12%. The platform consisted of a pillared architecture of a three-dimensional nanocomposite of perovskites fully infiltrating mesoporous TiO2, resulting in the formation of continuous phases and perovskite domains overlaid with a polymeric hole conductor. Since then, the PCE of our PSCs has been rapidly increased from 3% to over 20% certified efficiency. The unprecedented increase in the PCE can be attributed to the effective integration of the advantageous attributes of the refined bicontinuous architecture, deposition process, and composition of perovskite materials. Specifically, the bicontinuous architectures used in the high efficiency comprise a layer of perovskite sandwiched between mesoporous metal-oxide layer, which is a very thinner than that of used in conventional dye-sensitized solar cells, and hole-conducting contact materials with a metal back contact. The mesoporous scaffold can affect the hysteresis under different scan direction in measurements of PSCs. The hysteresis also greatly depends on the cell architecture and perovskite composition. In this Account, we will describe what we do with major aspects including (1) the film morphology through the development of intermediate chemistry retarding the rapid reaction between methylammonium or formamidinium iodide and lead halide (PbI2) for improved perovskite film formation; (2) the phase stability and band gap tuning of the perovskite layer through the materials engineering; (3) the development of electron and hole transporting materials for carrier-selective contacting layers; and (4) the adoption of p-i-n and n-i-p architectures depending on the position of the electron or hole conducting layer in front of incident light. Finally, we will summarize the recent incredible achievements in PSCs, and finally provide challenges facing the future development and commercialization of PSCs.

Fabrication of Efficient Formamidinium Tin Iodide Perovskite Solar Cells through SnF2-Pyrazine Complex.

To fabricate efficient formamidinium tin iodide (FASnI3) perovskite solar cells (PSCs), it is essential to deposit uniform and dense perovskite layers and reduce Sn(4+) content. Here we used solvent-engineering and nonsolvent dripping process with SnF2 as an inhibitor of Sn(4+). However, excess SnF2 induces phase separation on the surface of the perovskite film. In this work, we report the homogeneous dispersion of SnF2 via the formation of the SnF2-pyrazine complex. Consequently, we fabricated FASnI3 PSCs with high reproducibility, achieving a high power conversion efficiency of 4.8%. Furthermore, the encapsulated device showed a stable performance for over 100 days, maintaining 98% of its initial efficiency.

Solvent engineering for high-performance inorganic-organic hybrid perovskite solar cells.

Organolead trihalide perovskite materials have been successfully used as light absorbers in efficient photovoltaic cells. Two different cell structures, based on mesoscopic metal oxides and planar heterojunctions have already demonstrated very impressive advances in performance. Here, we report a bilayer architecture comprising the key features of mesoscopic and planar structures obtained by a fully solution-based process. We used CH3NH3 Pb(I(1-x)Br(x))3 (x = 0.1-0.15) as the absorbing layer and poly(triarylamine) as a hole-transporting material. The use of a mixed solvent of γ-butyrolactone and dimethylsulphoxide (DMSO) followed by toluene drop-casting leads to extremely uniform and dense perovskite layers via a CH3NH3I-PbI2-DMSO intermediate phase, and enables the fabrication of remarkably improved solar cells with a certified power-conversion efficiency of 16.2% and no hysteresis. These results provide important progress towards the understanding of the role of solution-processing in the realization of low-cost and highly efficient perovskite solar cells.

o-Methoxy substituents in spiro-OMeTAD for efficient inorganic-organic hybrid perovskite solar cells.

Three spiro-OMeTAD derivatives have been synthesized and characterized by (1)H/(13)C NMR spectroscopy and mass spectrometry. The optical and electronic properties of the derivatives were modified by changing the positions of the two methoxy substituents in each of the quadrants, as monitored by UV-vis spectroscopy and cyclic voltammetry measurements. The derivatives were employed as hole-transporting materials (HTMs), and their performances were compared for the fabrication of mesoporous TiO2/CH3NH3PbI3/HTM/Au solar cells. Surprisingly, the cell performance was dependent on the positions of the OMe substituents. The derivative with o-OMe substituents showed highly improved performance by exhibiting a short-circuit current density of 21.2 mA/cm(2), an open-circuit voltage of 1.02 V, and a fill factor of 77.6% under 1 sun illumination (100 mW/cm(2)), which resulted in an overall power conversion efficiency (PCE) of 16.7%, compared to ~15% for conventional p-OMe substituents. The PCE of 16.7% is the highest value reported to date for perovskite-based solar cells with spiro-OMeTAD.

Chemical management for colorful, efficient, and stable inorganic-organic hybrid nanostructured solar cells.

Chemically tuned inorganic-organic hybrid materials, based on CH3NH3(═MA)Pb(I(1-x)Br(x))3 perovskites, have been studied using UV-vis absorption and X-ray diffraction patterns and applied to nanostructured solar cells. The band gap engineering brought about by the chemical management of MAPb(I(1-x)Br(x))3 perovskites can be controllably tuned to cover almost the entire visible spectrum, enabling the realization of colorful solar cells. We demonstrate highly efficient solar cells exhibiting 12.3% in a power conversion efficiency of under standard AM 1.5, for the most efficient device, as a result of tunable composition for the light harvester in conjunction with a mesoporous TiO2 film and a hole conducting polymer. We believe that the works highlighted in this paper represent one step toward the realization of low-cost, high-efficiency, and long-term stability with colorful solar cells.

Sb(2)Se(3) -sensitized inorganic-organic heterojunction solar cells fabricated using a single-source precursor.

The photovoltaic performance of Sb2 Se3 -sensitized heterojunction solar cells, which were fabricated by a simple deposition of Sb2 Se3 on mesoporous TiO2 by an approach that features multiple cycles of spin coating with a single-source precursor solution and thermal decomposition, is reported. Poly[2,6-(4,4-bis(2-ethylhexyl)-4H-cyclopenta[2,1-b;3,4-b']dithiophene)-alt-4,7(2,1,3-benzothioadiazole)] was used as the hole-transporting material. The most efficient cell exhibited a short-circuit current density of 22.3 mA cm(-2) , an open-circuit voltage of 304.5 mV, and a fill factor of 47.2 %, yielding a power conversion efficiency of 3.21 % under standard test conditions (irradiation of 1000 W m(-2) , air mass=1.5 G). The results of this study imply that the developed approach has a high potential as a simple and effective route for the fabrication of efficient and inexpensive solar cells.

Redox-mediated changes in the release dynamics of lead (Pb) and bacterial community composition in a biochar amended soil contaminated with metal halide perovskite solar panel waste.

This study explored the redox-mediated changes in a lead (Pb) contaminated soil (900 mg/kg) due to the addition of solar cell powder (SC) and investigated the impact of biochar derived from soft wood pellet (SWP) and oil seed rape straw (OSR) (5% w/w) on Pb immobilization using an automated biogeochemical microcosm system. The redox potential (Eh) of the untreated (control; SC) and biochar treated soils (SC + SWP and SC + OSR) ranged from -151 mV to +493 mV. In SC, the dissolved Pb concentrations were higher under oxic (up to 2.29 mg L-1) conditions than reducing (0.13 mg L-1) conditions. The addition of SWP and OSR to soil immobilized Pb, decreased dissolved concentration, which could be possibly due to the increase of pH, co-precipitation of Pb with FeMn (hydro)oxides and pyromorphite, and complexation with biochar surface functional groups. The ability and efficiency of OSR for Pb immobilization were higher than SWP, owing to the higher pH and density of surface functional groups of OSR than SWP. Biochar enhanced the relative abundance of Proteobacteria irrespective of Eh changes, while the relative abundance of Bacteroidota increased under oxidizing conditions. Overall, we found that both OSR and SWP immobilized Pb in solar panel waste contaminated soil under both oxidizing and reducing redox conditions which may mitigate the potential risk of Pb contamination.

Quantum barriers engineering toward radiative and stable perovskite photovoltaic devices.

Efficient photovoltaic devices must be efficient light emitters to reach the thermodynamic efficiency limit. Here, we present a promising prospect of perovskite photovoltaics as bright emitters by harnessing the significant benefits of photon recycling, which can be practically achieved by suppressing interfacial quenching. We have achieved radiative and stable perovskite photovoltaic devices by the design of a multiple quantum well structure with long (∼3 nm) organic spacers with oleylammonium molecules at perovskite top interfaces. Our L-site exchange process (L: barrier molecule cation) enables the formation of stable interfacial structures with moderate conductivity despite the thick barriers. Compared to popular short (∼1 nm) Ls, our approach results in enhanced radiation efficiency through the recursive process of photon recycling. This leads to the realization of radiative perovskite photovoltaics with both high photovoltaic efficiency (in-lab 26.0%, certified to 25.2%) and electroluminescence quantum efficiency (19.7 % at peak, 17.8% at 1-sun equivalent condition). Furthermore, the stable crystallinity of oleylammonium-based quantum wells enables our devices to maintain high efficiencies for over 1000 h of operation and >2 years of storage.

Efficient inorganic-organic hybrid perovskite solar cells based on pyrene arylamine derivatives as hole-transporting materials.

A set of three N,N-di-p-methoxyphenylamine-substituted pyrene derivatives have successfully been synthesized and characterized by (1)H/(13)C NMR spectroscopy, mass spectrometry, and elemental analysis. The optical and electronic structures of the pyrene derivatives were adjusted by controlling the ratio of N,N-di-p-methoxyphenylamine to pyrene, and investigated by UV/vis spectroscopy and cyclic voltammetry. The pyrene derivatives were employed as hole-transporting materials (HTMs) in fabricating mesoporous TiO2/CH3NH3PbI3/HTMs/Au solar cells. The pyrene-based derivative Py-C exhibited a short-circuit current density of 20.2 mA/cm(2), an open-circuit voltage (Voc) of 0.886 V, and a fill factor of 69.4% under an illumination of 1 sun (100 mW/cm(2)), resulting in an overall power conversion efficiency of 12.4%. The performance is comparable to that of the well-studied spiro-OMeTAD, even though the Voc is slightly lower. Thus, this newly synthesized pyrene derivative holds promise as a HTM for highly efficient perovskite-based solar cells.

Influence of niobium doping in hierarchically organized titania nanostructure on performance of dye-sensitized solar cells.

Niobium doped hierarchically organized TiO2 nanostructures composed of 20 nm size anatase nanocrystals were synthesized using pulsed laser deposition (PLD). The Nb doping concentration could be facilely controlled by adjusting the concentration of Nb in target materials. We could investigate the influence of Nb doping in the TiO2 photoelectrode on the cell performance of dye-sensitized solar cells (DSSCs) by the exclusion of morphological effects using the prepared Nb-doped TiO2 anostructures. We found no significant change in short circuit current density (Jsc) as a function of Nb doping concentration. However, open circuit voltage (Voc) and fill factor (FF) monotonously decrease with increasing Nb concentration. Dark current characteristics of the DSSCs reveal that the decrease in Voc and FF is attributed to the decrease in shunt resistance due to the increase in conductivity TiO2 by Nb doping. However, electrochemical impedance spectra (EIS) analysis at open circuit condition under illumination showed that the resistance at the TiO2/dye/electrolyte interface increases with Nb concentration, revealing that Nb doping suppress the charge recombination at the interface. In addition, electron life time obtained using characteristic frequency in Bode plot increases from 14 msec to 56 msec with increasing Nb concentration from 0 to 1.2 at%. This implies that the improved light harvesting can be achieved by increasing diffusion length through Nb-doping in the conventional TiO2 photoelectrode.

High-Performance Cold Cathode X-ray Tubes Using a Carbon Nanotube Field Electron Emitter.

A cold cathode X-ray tube was fabricated using a carbon nanotube (CNT) field electron emitter made by a free-standing CNT film which is composed of a highly packed CNT network. A lot of CNT bundles with a sharp tip are vertically aligned at the edge of the thin CNT film with a length of 10 mm and a thickness of 7 µm. The cold cathode X-ray tube using the CNT field emitter presents an extremely high tube current density of 152 A/cm2 (corresponding to tube current of 106.4 mA), the electron beam transmittance of 95.2% and a small focal spot size (FSS) of 0.5 mm. In addition, the cold cathode X-ray tube also shows stable lifetime during 100 000 shots. High emission current density of the cold cathode X-ray tube is mainly attributed to a lot of electron emission sites at an edge of the CNT film. The small FSS is caused by an ensemble of the CNT field electron emitter made by a free-standing thin CNT film and the optimized curve-shape elliptical focusing lens. Based on obtained results, the cold cathode X-ray tube can be widely used for various X-ray applications such as medical diagnosis systems and security check systems in the future.

Suppressing Halide Segregation in Wide-Band-Gap Mixed-Halide Perovskite Layers through Post-Hot Pressing.

Mixed-halide perovskites (MHPs) have attracted attention as suitable wide-band-gap candidate materials for tandem applications owing to their facile band-gap tuning. However, when smaller bromide ions are incorporated into iodides to tune the band gap, photoinduced halide segregation occurs, which leads to voltage deficit and photoinstability. Here, we propose an original post-hot pressing (PHP) treatment that suppresses halide segregation in MHPs with a band gap of 2.0 eV. The PHP treatment reconstructs open-structured grain boundaries (GBs) as compact GBs through constrained grain growth in the in-plane direction, resulting in the inhibition of defect-mediated ion migration in GBs. The PHP-treated wide-band-gap (2.0 eV) MHP solar cells showed a high efficiency of over 11%, achieving an open-circuit voltage (Voc) of 1.35 V and improving the maintenance of the initial efficiency under the working condition at AM 1.5G. The results reveal that the management of GBs is necessary to secure the stability of wide-band-gap MHP devices in terms of halide segregation.

Effects of photon recycling and scattering in high-performance perovskite solar cells.

Efficient external radiation is essential for solar cells to achieve high power conversion efficiency (PCE). The classical limit of 1/2n2 (n, refractive index) for electroluminescence quantum efficiency (ELQE) has recently been approached by perovskite solar cells (PSCs). Photon recycling (PR) and light scattering can provide an opportunity to surpass this limit. We investigate the role of PR and scattering in practical device operation using a radiative PSC with an ELQE (13.7% at 1 sun) that significantly surpasses the classical limit (7.4%). We experimentally analyze the contributions of PR and scattering to this strong radiation. A novel optical model reveals an increase of 39 mV in the voltage of our PSC. This analysis can provide design principles for future PSCs to approach the Shockley-Queisser efficiency limit.

Simultaneous Enhanced Efficiency and Stability of Perovskite Solar Cells Using Adhesive Fluorinated Polymer Interfacial Material.

For enhancing the performance and long-term stability of perovskite solar cell (PSC) devices, interfacial engineering between the perovskite and hole-transporting material (HTM) is important. We developed a fluorinated conjugated polymer PFPT3 and used it as an interfacial layer between the perovskite and HTM layers in normal-type PSCs. Interaction of perovskite and PFPT3 via Pb-F bonding effectively induces an interfacial dipole moment, which resulted in energy-level bending; this was favorable for charge transfer and hole extraction at the interface. The PSC device achieved an increased efficiency of 22.00% with an open-circuit voltage of 1.13 V, short-circuit current density of 24.34 mA/cm2, and fill factor of 0.80 from a reverse scan and showed an averaged power conversion efficiency of 21.59%, which was averaged from forward and reverse scans. Furthermore, the device with PFPT3 showed much improved stability under an 85% RH condition because hydrophobic PFPT3 reduced water permeation into the perovskite layer, and more importantly, the enhanced contact adhesion at the PFPT3-mediated perovskite/HTM interface suppressed surface delamination and retarded water intrusion. The fluorinated conjugated polymeric interfacial material is effective for improving not only the efficiency but also the stability of the PSC devices.