3D Printing of Multiscale Ti64-Based Lattice Electrocatalysts for Robust Oxygen Evolution Reaction.

Electrically assisted water splitting is an endurable strategy for hydrogen production, but the sluggish kinetics of oxygen evolution reaction (OER) extremely restrict the large-scale production of hydrogen. Developing highly efficient and non-precious catalytic materials is essential to accelerate the sluggish kinetics of OER. However, currently used catalyst supports, such as copper foam, suffer from inferior corrosion resistance and structural stability, resulting in the disabled functionality of 3D conductive networks. To this end, a novel 3D freestanding electrode with corrosion-resistant and robust Ti-6Al-4V titanium alloy lattice as the catalyst support is designed via a 3D printing technology of selective laser melting. After the coating of core-shell Cu(OH)2@CoNi carbonate hydroxides (CoNiCH) on the designed lattice, a unique micro/nano-sized hierarchical porous structure is formed, which endows the electrocatalyst with a promising electrocatalytic activity (a low overpotential of 355 mV at 30 mA cm-2 and Tafel slope of 125.3 mV dec-1 ). Computational results indicate that the CoNiCH exhibits optimized electron transfer and the catalytic activity of the Ni site is higher than that of the Co site in the CoNiCH. Therefore, the integration of robust catalyst supports and highly active materials opens up an avenue for reliable and high-performance OER electrocatalysts.

Tribological Behavior of TiC Particles Reinforced 316Lss Composite Fabricated Using Selective Laser Melting.

In order to improve the abrasion performance of 316Lss, make full use of its advantages and broaden its application fields, the tribological behavior of the TiC particles reinforced 316Lss composites-which were manufactured by selective laser melting (SLM)-were investigated. In this study, GCr15 bearing steel was selected as the friction material and experiments on the sliding friction and wear under different loads of 15 N, 25 N and 35 N at the sliding speeds of 60, 80 and 100 mm/min were carried out, respectively. The results show that the wear performance of the TiC/316Lss composite is higher than that of the matrix during the friction and wear experiments under all conditions and the wear rate of the TiC/316Lss composite decreases with increasing the friction rate. Similar to the wear mechanism under different loads, it changes from abrasive wear to delamination wear and severe oxidative wear. At the same time, the mechanical mixed layer formed at a high speed has a protective effect on the matrix. The reason for this phenomenon is that the mechanical properties of the TiC/316Lss composites are significantly improved due to the addition of TiC particles, the refinement of cells near the TiC particles and the formation of a large number of dislocations. In addition, due to the presence of the TiC particles, the hardness and strength of the TiC/316Lss composites are greatly improved, thus the processing hardening ability of sub-surface has been improved.

The Heat Treatment Influence on the Microstructure and Hardness of TC4 Titanium Alloy Manufactured via Selective Laser Melting.

In this research, the effect of several heat treatments on the microstructure and microhardness of TC4 (Ti6Al4V) titanium alloy processed by selective laser melting (SLM) is studied. The results showed that the original acicular martensite α'-phase in the TC4 alloy formed by SLM is converted into a lamellar mixture of α + ß for heat treatment temperatures below the critical temperature (T0 at approximately 893 °C). With the increase of heat treatment temperature, the size of the lamellar mixture structure inside of the TC4 part gradually grows. When the heat treatment temperature is above T0, because the cooling rate is relatively steep, the ß-phase recrystallization transforms into a compact secondary α-phase, and a basketweave structure can be found because the primary α-phase develop and connect or cross each other with different orientations. The residence time for TC4 SLM parts when the treatment temperature is below the critical temperature has little influence: both the α-phase and the ß-phase will tend to coarsen but hinder each other, thereby limiting grain growth. The microhardness gradually decreases with increasing temperature when the TC4 SLM part is treated below the critical temperature. Conversely, the microhardness increases significantly with increasing temperature when the TC4 SLM part is treated above the critical temperature.