High carrier mobility along the [111] orientation in Cu2O photoelectrodes.

Solar fuels offer a promising approach to provide sustainable fuels by harnessing sunlight1,2. Following a decade of advancement, Cu2O photocathodes are capable of delivering a performance comparable to that of photoelectrodes with established photovoltaic materials3-5. However, considerable bulk charge carrier recombination that is poorly understood still limits further advances in performance6. Here we demonstrate performance of Cu2O photocathodes beyond the state-of-the-art by exploiting a new conceptual understanding of carrier recombination and transport in single-crystal Cu2O thin films. Using ambient liquid-phase epitaxy, we present a new method to grow single-crystal Cu2O samples with three crystal orientations. Broadband femtosecond transient reflection spectroscopy measurements were used to quantify anisotropic optoelectronic properties, through which the carrier mobility along the [111] direction was found to be an order of magnitude higher than those along other orientations. Driven by these findings, we developed a polycrystalline Cu2O photocathode with an extraordinarily pure (111) orientation and (111) terminating facets using a simple and low-cost method, which delivers 7 mA cm-2 current density (more than 70% improvement compared to that of state-of-the-art electrodeposited devices) at 0.5 V versus a reversible hydrogen electrode under air mass 1.5 G illumination, and stable operation over at least 120 h.

Photosynthesis re-wired on the pico-second timescale.

Photosystems II and I (PSII, PSI) are the reaction centre-containing complexes driving the light reactions of photosynthesis; PSII performs light-driven water oxidation and PSI further photo-energizes harvested electrons. The impressive efficiencies of the photosystems have motivated extensive biological, artificial and biohybrid approaches to 're-wire' photosynthesis for higher biomass-conversion efficiencies and new reaction pathways, such as H2 evolution or CO2 fixation1,2. Previous approaches focused on charge extraction at terminal electron acceptors of the photosystems3. Electron extraction at earlier steps, perhaps immediately from photoexcited reaction centres, would enable greater thermodynamic gains; however, this was believed impossible with reaction centres buried at least 4 nm within the photosystems4,5. Here, we demonstrate, using in vivo ultrafast transient absorption (TA) spectroscopy, extraction of electrons directly from photoexcited PSI and PSII at early points (several picoseconds post-photo-excitation) with live cyanobacterial cells or isolated photosystems, and exogenous electron mediators such as 2,6-dichloro-1,4-benzoquinone (DCBQ) and methyl viologen. We postulate that these mediators oxidize peripheral chlorophyll pigments participating in highly delocalized charge-transfer states after initial photo-excitation. Our results challenge previous models that the photoexcited reaction centres are insulated within the photosystem protein scaffold, opening new avenues to study and re-wire photosynthesis for biotechnologies and semi-artificial photosynthesis.

Floating perovskite-BiVO4 devices for scalable solar fuel production.

Photoelectrochemical (PEC) artificial leaves hold the potential to lower the costs of sustainable solar fuel production by integrating light harvesting and catalysis within one compact device. However, current deposition techniques limit their scalability1, whereas fragile and heavy bulk materials can affect their transport and deployment. Here we demonstrate the fabrication of lightweight artificial leaves by employing thin, flexible substrates and carbonaceous protection layers. Lead halide perovskite photocathodes deposited onto indium tin oxide-coated polyethylene terephthalate achieved an activity of 4,266 µmol H2 g-1 h-1 using a platinum catalyst, whereas photocathodes with a molecular Co catalyst for CO2 reduction attained a high CO:H2 selectivity of 7.2 under lower (0.1 sun) irradiation. The corresponding lightweight perovskite-BiVO4 PEC devices showed unassisted solar-to-fuel efficiencies of 0.58% (H2) and 0.053% (CO), respectively. Their potential for scalability is demonstrated by 100 cm2 stand-alone artificial leaves, which sustained a comparable performance and stability (of approximately 24 h) to their 1.7 cm2 counterparts. Bubbles formed under operation further enabled 30-100 mg cm-2 devices to float, while lightweight reactors facilitated gas collection during outdoor testing on a river. This leaf-like PEC device bridges the gulf in weight between traditional solar fuel approaches, showcasing activities per gram comparable to those of photocatalytic suspensions and plant leaves. The presented lightweight, floating systems may enable open-water applications, thus avoiding competition with land use.

Understanding the local chemical environment of bioelectrocatalysis.

Bioelectrochemistry employs an array of high-surface-area meso- and macroporous electrode architectures to increase protein loading and the electrochemical current response. While the local chemical environment has been studied in small-molecule and heterogenous electrocatalysis, conditions in enzyme electrochemistry are still commonly established based on bulk solution assays, without appropriate consideration of the nonequilibrium conditions of the confined electrode space. Here, we apply electrochemical and computational techniques to explore the local environment of fuel-producing oxidoreductases within porous electrode architectures. This improved understanding of the local environment enabled simple manipulation of the electrolyte solution by adjusting the bulk pH and buffer pKa to achieve an optimum local pH for maximal activity of the immobilized enzyme. When applied to macroporous inverse opal electrodes, the benefits of higher loading and increased mass transport were employed, and, consequently, the electrolyte adjusted to reach -8.0 mA ⋅ cm-2 for the H2 evolution reaction and -3.6 mA ⋅ cm-2 for the CO2 reduction reaction (CO2RR), demonstrating an 18-fold improvement on previously reported enzymatic CO2RR systems. This research emphasizes the critical importance of understanding the confined enzymatic chemical environment, thus expanding the known capabilities of enzyme bioelectrocatalysis. These considerations and insights can be directly applied to both bio(photo)electrochemical fuel and chemical synthesis, as well as enzymatic fuel cells, to significantly improve the fundamental understanding of the enzyme-electrode interface as well as device performance.

Multi-Variable Multi-Metric Optimization of Self-Assembled Photocatalytic CO2 Reduction Performance Using Machine Learning Algorithms.

The sunlight-driven reduction of CO2 into fuels and platform chemicals is a promising approach to enable a circular economy. However, established optimization approaches are poorly suited to multivariable multimetric photocatalytic systems because they aim to optimize one performance metric while sacrificing the others and thereby limit overall system performance. Herein, we address this multimetric challenge by defining a metric for holistic system performance that takes multiple figures of merit into account, and employ a machine learning algorithm to efficiently guide our experiments through the large parameter matrix to make holistic optimization accessible for human experimentalists. As a test platform, we employ a five-component system that self-assembles into photocatalytic micelles for CO2-to-CO reduction, which we experimentally optimized to simultaneously improve yield, quantum yield, turnover number, and frequency while maintaining high selectivity. Leveraging the data set with machine learning algorithms allows quantification of each parameter's effect on overall system performance. The buffer concentration is unexpectedly revealed as the dominating parameter for optimal photocatalytic activity, and is nearly four times more important than the catalyst concentration. The expanded use and standardization of this methodology to define and optimize holistic performance will accelerate progress in different areas of catalysis by providing unprecedented insights into performance bottlenecks, enhancing comparability, and taking results beyond comparison of subjective figures of merit.

Photocatalytic CO2 Reduction Using Homogeneous Carbon Dots with a Molecular Cobalt Catalyst.

A simple and precious-metal free photosystem for the reduction of aqueous CO2 to syngas (CO and H2) is reported consisting of carbon dots (CDs) as the sole light harvester together with a molecular cobalt bis(terpyridine) CO2 reduction co-catalyst. This homogeneous photocatalytic system operates in the presence of a sacrificial electron donor (triethanolamine) in DMSO/H2O solution at ambient temperature. The photocatalytic system exhibits an activity of 7.7 ± 0.2 mmolsyngas gCDs -1 (3.6 ± 0.2 mmolCO gCDs -1 and 4.1 ± 0.1 mmolH2 gCDs -1) after 24 hours of full solar spectrum irradiation (AM 1.5G). Spectroscopic and electrochemical characterization supports that this photocatalytic performance is attributed to a favorable association between CDs and the molecular cobalt catalyst, which results in improved interfacial photoelectron transfer and catalytic mechanism. This work provides a scalable and inexpensive platform for the development of CO2 photoreduction systems using CDs.

Microplastics and anthropogenic fibre concentrations in lakes reflect surrounding land use.

Pollution from microplastics and anthropogenic fibres threatens lakes, but we know little about what factors predict its accumulation. Lakes may be especially contaminated because of long water retention times and proximity to pollution sources. Here, we surveyed anthropogenic microparticles, i.e., microplastics and anthropogenic fibres, in surface waters of 67 European lakes spanning 30° of latitude and large environmental gradients. By collating data from >2,100 published net tows, we found that microparticle concentrations in our field survey were higher than previously reported in lakes and comparable to rivers and oceans. We then related microparticle concentrations in our field survey to surrounding land use, water chemistry, and plastic emissions to sites estimated from local hydrology, population density, and waste production. Microparticle concentrations in European lakes quadrupled as both estimated mismanaged waste inputs and wastewater treatment loads increased in catchments. Concentrations decreased by 2 and 5 times over the range of surrounding forest cover and potential in-lake biodegradation, respectively. As anthropogenic debris continues to pollute the environment, our data will help contextualise future work, and our models can inform control and remediation efforts.

Connecting Biological and Synthetic Approaches for Electrocatalytic CO2 Reduction.

Electrocatalytic CO2 reduction has developed into a broad field, spanning fundamental studies of enzymatic 'model' catalysts to synthetic molecular catalysts and heterogeneous gas diffusion electrodes producing commercially relevant quantities of product. This diversification has resulted in apparent differences and a disconnect between seemingly related approaches when using different types of catalysts. Enzymes possess discrete and well understood active sites that can perform reactions with high selectivity and activities at their thermodynamic limit. Synthetic small molecule catalysts can be designed with desired active site composition but do not yet display enzyme-like performance. These properties of the biological and small molecule catalysts contrast with heterogeneous materials, which can contain multiple, often poorly understood active sites with distinct reactivity and therefore introducing significant complexity in understanding their activities. As these systems are being better understood and the continuously improving performance of their heterogeneous active sites closes the gap with enzymatic activity, this performance difference between heterogeneous and enzymatic systems begins to close. This convergence removes the barriers between using different types of catalysts and future challenges can be addressed without multiple efforts as a unified picture for the biological-synthetic catalyst spectrum emerges.

Thermoelectric-Photoelectrochemical Water Splitting under Concentrated Solar Irradiation.

Photoelectrochemical devices could play a crucial role toward fuel production in a circular economy. Yet, light absorption suffers losses from thermalization and the inability to use low-energy photons. Here, we demonstrate that photoelectrochemical reactors can utilize this waste heat by integrating thermoelectric modules, which provide additional voltage under concentrated light irradiation. While most single semiconductors require external bias, we already accomplish unassisted water splitting under 2 sun irradiation by wiring a BiVO4 photoanode to a thermoelectric element, whereas the photocurrent of a perovskite-BiVO4 tandem system is enhanced 1.7-fold at 5 sun. This strategy is particularly suitable for photoanodes with more positive onset potentials like hematite, with thermoelectric-perovskite-Fe2O3 systems achieving a 29.7× overall photocurrent increase at 5 sun over conventional perovskite-Fe2O3 devices without light concentration. This thermal management approach provides a universal strategy to facilitate widespread solar fuel production, as light concentration increases output, reduces the reactor size and cost, and may enhance catalysis.

Chemoenzymatic Photoreforming: A Sustainable Approach for Solar Fuel Generation from Plastic Feedstocks.

Plastic upcycling through catalytic transformations is an attractive concept to valorize waste, but the clean and energy-efficient production of high-value products from plastics remains challenging. Here, we introduce chemoenzymatic photoreforming as a process coupling enzymatic pretreatment and solar-driven reforming of polyester plastics under mild temperatures and pH to produce clean H2 and value-added chemicals. Chemoenzymatic photoreforming demonstrates versatility in upcycling polyester films and nanoplastics to produce H2 at high yields reaching ∼103-104 µmol gsub-1 and activities at >500 µmol gcat-1 h-1. Enzyme-treated plastics were also used as electron donors for photocatalytic CO2-to-syngas conversion with a phosphonated cobalt bis(terpyridine) catalyst immobilized on TiO2 nanoparticles (TiO2|CotpyP). Finally, techno-economic analyses reveal that the chemoenzymatic photoreforming approach has the potential to drastically reduce H2 production costs to levels comparable to market prices of H2 produced from fossil fuels while maintaining low CO2-equivalent emissions.

Long-term solar water and CO2 splitting with photoelectrochemical BiOI-BiVO4 tandems.

Photoelectrochemical (PEC) devices have been developed for direct solar fuel production but the limited stability of submerged light absorbers can hamper their commercial prospects.1,2 Here, we demonstrate photocathodes with an operational H2 evolution activity over weeks, by integrating a BiOI light absorber into a robust, oxide-based architecture with a graphite paste conductive encapsulant. In this case, the activity towards proton and CO2 reduction is mainly limited by catalyst degradation. We also introduce multiple-pixel devices as an innovative design principle for PEC systems, displaying superior photocurrents, onset biases and stability over corresponding conventional single-pixel devices. Accordingly, PEC tandem devices comprising multiple-pixel BiOI photocathodes and BiVO4 photoanodes can sustain bias-free water splitting for 240 h, while devices with a Cu92In8 alloy catalyst demonstrate unassisted syngas production from CO2.

Solar Panel Technologies for Light-to-Chemical Conversion.

The sustainable synthesis of fuels and chemicals is key to attaining a carbon-neutral economy. This can be achieved by mimicking the light-harvesting and catalytic processes occurring in plants. Solar fuel production is commonly performed via established approaches, including photovoltaic-electrochemical (PV-EC), photoelectrochemical (PEC), and photocatalytic (PC) systems. A recent shift saw these systems evolve into integrated, compact panels, which suit practical applications through their simplicity, scalability, and ease of operation. This advance has resulted in a suite of apparently similar technologies, including the so-called artificial leaves and PC sheets. In this Account, we compare these different thin film technologies based on their micro- and nanostructure (i.e., layered vs particulate), operation principle (products occurring on the same or different sides of the panel), and product/reaction scope (overall water splitting and CO2 reduction, or organics, biomass, and waste conversion).For this purpose, we give an overview of developments established over the past few years in our laboratory. Two light absorbers are generally required to overcome the thermodynamic challenges of coupling water oxidation to proton or CO2 reduction with good efficiency. Hence, tandem artificial leaves combine a lead halide perovskite photocathode with a BiVO4 photoanode to generate syngas (a mixture of H2 and CO), whereas PC sheets involve metal-ion-doped SrTiO3 and BiVO4 particles for selective formate synthesis from CO2 and water. On the other hand, only a single light absorber is needed for coupling H2 evolution to organics oxidation in the thermodynamically less demanding photoreforming process. This can be performed by immobilized carbon nitride (CNx) in the case of PC sheets or by a single perovskite light absorber in the case of PEC reforming leaves. Such systems can be integrated with a range of inorganic, molecular, and biological catalysts, including metal alloys, molecular cobalt complexes, enzymes, and bacteria, with low overpotentials and high catalytic activities toward selective product formation.This wide reaction scope introduces new challenges toward quantifying and comparing the performance of different systems. To this end, we propose new metrics to evaluate the performance of solar fuel panels based on the areal product rates and commercial product value. We further explore the key opportunities and challenges facing the commercialization of thin film technologies for solar fuels research, including performance losses over larger areas and catalyst/device recyclability. Finally, we identify emerging applications beyond fuels, where such light-driven panels can make a difference, including the waste management, chemical synthesis, and pharmaceutical industries. In the long term, these aspects may facilitate a transition toward a light-driven circular economy.

A three-dimensional hybrid electrode with electroactive microbes for efficient electrogenesis and chemical synthesis.

Integration of electroactive bacteria into electrodes combines strengths of intracellular biochemistry with electrochemistry for energy conversion and chemical synthesis. However, such biohybrid systems are often plagued with suboptimal electrodes, which limits the incorporation and productivity of the bacterial colony. Here, we show that an inverse opal-indium tin oxide electrode hosts a large population of current-producing Geobacter and attains a current density of 3 mA cm-2 stemming from bacterial respiration. Differential gene expression analysis revealed Geobacter's transcriptional regulations to express more electron-relaying proteins when interfaced with electrodes. The electrode also allows coculturing with Shewanella for syntrophic electrogenesis, which grants the system additional flexibility in converting electron donors. The biohybrid electrode containing Geobacter can also catalyze the reduction of soluble fumarate and heterogenous graphene oxide, with electrons from an external power source or an irradiated photoanode. This biohybrid electrode represents a platform to employ live cells for sustainable power generation and biosynthesis.

Comproportionation of CO2 and Cellulose to Formate Using a Floating Semiconductor-Enzyme Photoreforming Catalyst.

Formate production via both CO2 reduction and cellulose oxidation in a solar-driven process is achieved by a semi-artificial biohybrid photocatalyst consisting of immobilized formate dehydrogenase on titanium dioxide (TiO2 |FDH) producing up to 1.16±0.04 mmolformate g TiO 2 ${{_{\ {\rm TiO}{_{2}}}}}$ -1 in 24 hours at 30 °C and 101 kPa under anaerobic conditions. Isotopic labeling experiments with 13 C-labeled substrates support the mechanism of stoichiometric formate formation through both redox half-reactions. TiO2 |FDH was further immobilized on hollow glass microspheres to perform more practical floating photoreforming allowing vertical solar light illumination with optimal light exposure of the photocatalyst to real sunlight. Enzymatic cellulose depolymerization coupled to the floating photoreforming catalyst generates 0.36±0.04 mmolformate per m2 irradiation area after 24 hours. This work demonstrates the synergistic solar-driven valorization of solid and gaseous waste streams using a biohybrid photoreforming catalyst in aqueous solution and will thus provide inspiration for the development of future semi-artificial waste-to-chemical conversion strategies.

Carboxysome-Inspired Electrocatalysis using Enzymes for the Reduction of CO2 at Low Concentrations.

The electrolysis of dilute CO2 streams suffers from low concentrations of dissolved substrate and its rapid depletion at the electrolyte-electrocatalyst interface. These limitations require first energy-intensive CO2 capture and concentration, before electrolyzers can achieve acceptable performances. For direct electrocatalytic CO2 reduction from low-concentration sources, we introduce a strategy that mimics the carboxysome in cyanobacteria by utilizing microcompartments with nanoconfined enzymes in a porous electrode. A carbonic anhydrase accelerates CO2 hydration kinetics and minimizes substrate depletion by making all dissolved carbon available for utilization, while a highly efficient formate dehydrogenase reduces CO2 cleanly to formate; down to even atmospheric concentrations of CO2 . This bio-inspired concept demonstrates that the carboxysome provides a viable blueprint for the reduction of low-concentration CO2 streams to chemicals by using all forms of dissolved carbon.

In situ Detection of Cobaloxime Intermediates During Photocatalysis Using Hollow-Core Photonic Crystal Fiber Microreactors.

Hollow-core photonic crystal fibers (HC-PCFs) provide a novel approach for in situ UV/Vis spectroscopy with enhanced detection sensitivity. Here, we demonstrate that longer optical path lengths than afforded by conventional cuvette-based UV/Vis spectroscopy can be used to detect and identify the CoI and CoII states in hydrogen-evolving cobaloxime catalysts, with spectral identification aided by comparison with DFT-simulated spectra. Our findings show that there are two types of signals observed for these molecular catalysts; a transient signal and a steady-state signal, with the former being assigned to the CoI state and the latter being assigned to the CoII state. These observations lend support to a unimolecular pathway, rather than a bimolecular pathway, for hydrogen evolution. This study highlights the utility of fiber-based microreactors for understanding these and a much wider range of homogeneous photocatalytic systems in the future.

Self-Assembled Liposomes Enhance Electron Transfer for Efficient Photocatalytic CO2 Reduction.

Light-driven conversion of CO2 to chemicals provides a sustainable alternative to fossil fuels, but homogeneous systems are typically limited by cross reactivity between different redox half reactions and inefficient charge separation. Herein, we present the bioinspired development of amphiphilic photosensitizer and catalyst pairs that self-assemble in lipid membranes to overcome some of these limitations and enable photocatalytic CO2 reduction in liposomes using precious metal-free catalysts. Using sodium ascorbate as a sacrificial electron source, a membrane-anchored alkylated cobalt porphyrin demonstrates higher catalytic CO production (1456 vs 312 turnovers) and selectivity (77 vs 11%) compared to its water-soluble nonalkylated counterpart. Time-resolved and steady-state spectroscopy revealed that self-assembly facilitates this performance enhancement by enabling a charge-separation state lifetime increase of up to two orders of magnitude in the dye while allowing for a ninefold faster electron transfer to the catalyst. Spectroelectrochemistry and density functional theory calculations of the alkylated Co porphyrin catalyst support a four-electron-charging mechanism that activates the catalyst prior to catalysis, together with key catalytic intermediates. Our molecular liposome system therefore benefits from membrane immobilization and provides a versatile and efficient platform for photocatalysis.

Engineering Electro- and Photocatalytic Carbon Materials for CO2 Reduction by Formate Dehydrogenase.

Semiartificial approaches to renewable fuel synthesis exploit the integration of enzymes with synthetic materials for kinetically efficient fuel production. Here, a CO2 reductase, formate dehydrogenase (FDH) from Desulfovibrio vulgaris Hildenborough, is interfaced with carbon nanotubes (CNTs) and amorphous carbon dots (a-CDs). Each carbon substrate, tailored for electro- and photocatalysis, is functionalized with positive (-NHMe2+) and negative (-COO-) chemical surface groups to understand and optimize the electrostatic effect of protein association and orientation on CO2 reduction. Immobilization of FDH on positively charged CNT electrodes results in efficient and reversible electrochemical CO2 reduction via direct electron transfer with >90% Faradaic efficiency and -250 µA cm-2 at -0.6 V vs SHE (pH 6.7 and 25 °C) for formate production. In contrast, negatively charged CNTs only result in marginal currents with immobilized FDH. Quartz crystal microbalance analysis and attenuated total reflection infrared spectroscopy confirm the high binding affinity of active FDH to CNTs. FDH has subsequently been coupled to a-CDs, where the benefits of the positive charge (-NHMe2+-terminated a-CDs) were translated to a functional CD-FDH hybrid photocatalyst. High rates of photocatalytic CO2 reduction (turnover frequency: 3.5 × 103 h-1; AM 1.5G) with dl-dithiothreitol as the sacrificial electron donor were obtained after 6 h, providing benchmark rates for homogeneous photocatalytic CO2 reduction with metal-free light absorbers. This work provides a rational basis to understand interfacial surface/enzyme interactions at electrodes and photosensitizers to guide improvements with catalytic biohybrid materials.

Spectroelectrochemistry of Water Oxidation Kinetics in Molecular versus Heterogeneous Oxide Iridium Electrocatalysts.

Water oxidation is the step limiting the efficiency of electrocatalytic hydrogen production from water. Spectroelectrochemical analyses are employed to make a direct comparison of water oxidation reaction kinetics between a molecular catalyst, the dimeric iridium catalyst [Ir2(pyalc)2(H2O)4-(µ-O)]2+ (IrMolecular, pyalc = 2-(2'pyridinyl)-2-propanolate) immobilized on a mesoporous indium tin oxide (ITO) substrate, with that of an heterogeneous electrocatalyst, an amorphous hydrous iridium (IrOx) film. For both systems, four analogous redox states were detected, with the formation of Ir(4+)-Ir(5+) being the potential-determining step in both cases. However, the two systems exhibit distinct water oxidation reaction kinetics, with potential-independent first-order kinetics for IrMolecular contrasting with potential-dependent kinetics for IrOx. This is attributed to water oxidation on the heterogeneous catalyst requiring co-operative effects between neighboring oxidized Ir centers. The ability of IrMolecular to drive water oxidation without such co-operative effects is explained by the specific coordination environment around its Ir centers. These distinctions between molecular and heterogeneous reaction kinetics are shown to explain the differences observed in their water oxidation electrocatalytic performance under different potential conditions.