Direct Correlation of Charge Transfer Absorption with Molecular Donor:Acceptor Interfacial Area via Photothermal Deflection Spectroscopy.

Here we show that the charge transfer (CT) absorption signal in bulk-heterojunction solar cell blends, measured by photothermal deflection spectroscopy, is directly proportional to the density of molecular donor:acceptor interfaces. Since the optical transitions from the ground state to the interfacial CT state are weakly allowed at photon energies below the optical gap of both the donor and acceptor, we can exploit the use of this sensitive linear absorption spectroscopy for such quantification. Moreover, we determine the absolute molar extinction coefficient of the CT transition for an archetypical polymer:fullerene interface. The latter is ∼100 times lower than the extinction coefficient of the donor chromophore involved, allowing us to experimentally estimate the transition dipole moment as 0.3 D and the electronic coupling between the ground and CT states to be on the order of 30 meV.

A synthetic resilin is largely unstructured.

Proresilin is the precursor protein for resilin, an extremely elastic, hydrated, cross-linked insoluble protein found in insects. We investigated the secondary-structure distribution in solution of a synthetic proresilin (AN16), based on 16 units of the consensus proresilin repeat from Anopheles gambiae. Raman spectroscopy was used to verify that the secondary-structure distributions in cross-linked AN16 resilin and in AN16 proresilin are similar, and hence that solution techniques (such as NMR and circular dichroism) may be used to gain information about the structure of the cross-linked solid. The synthetic proresilin AN16 is an intrinsically unstructured protein, displaying under native conditions many of the characteristics normally observed in denatured proteins. There are no apparent alpha-helical or beta-sheet features in the NMR spectra, and the majority of backbone protons and carbons exhibit chemical shifts characteristic of random-coil configurations. Relatively few peaks are observed in the nuclear Overhauser effect spectra, indicating that overall the protein is dynamic and unstructured. The radius of gyration of AN16 corresponds to the value expected for a denatured protein of similar chain length. This high degree of disorder is also consistent with observed circular dichroism and Raman spectra. The temperature dependences of the NH proton chemical shifts were also measured. Most values were indicative of protons exposed to water, although smaller dependences were observed for glycine and alanine within the Tyr-Gly-Ala-Pro sequence conserved in all resilins found to date, which is the site of dityrosine cross-link formation. This result implies that these residues are involved in hydrogen bonds, possibly to enable efficient self-association and subsequent cross-linking. The beta-spiral model for elastic proteins, where the protein is itself shaped like a spring, is not supported by the results for AN16. Both the random-network elastomer model and the sliding beta-turn model are consistent with the data. The results indicate a flat energy landscape for AN16, with very little energy required to switch between conformations. This ease of switching is likely to lead to the extremely low energy loss on deformation of resilin.

Differentially pumped spray deposition as a rapid screening tool for organic and perovskite solar cells.

We report a spray deposition technique as a screening tool for solution processed solar cells. A dual-feed spray nozzle is introduced to deposit donor and acceptor materials separately and to form blended films on substrates in situ. Using a differential pump system with a motorised spray nozzle, the effect of film thickness, solution flow rates and the blend ratio of donor and acceptor materials on device performance can be found in a single experiment. Using this method, polymer solar cells based on poly(3-hexylthiophene) (P3HT):(6,6)-phenyl C61 butyric acid methyl ester (PC61BM) are fabricated with numerous combinations of thicknesses and blend ratios. Results obtained from this technique show that the optimum ratio of materials is consistent with previously reported values confirming this technique is a very useful and effective screening method. This high throughput screening method is also used in a single-feed configuration. In the single-feed mode, methylammonium iodide solution is deposited on lead iodide films to create a photoactive layer of perovskite solar cells. Devices featuring a perovskite layer fabricated by this spray process demonstrated a power conversion efficiencies of up to 7.9%.

Toward large scale roll-to-roll production of fully printed perovskite solar cells.

Fully printed perovskite solar cells are demonstrated with slot-die coating, a scalable printing method. A sequential slot-die coating process is developed to produce efficient perovskite solar cells and to be used in a large-scale roll-to-roll printing process. All layers excluding the electrodes are printed and devices demonstrate up to 11.96% power conversion efficiency. It is also demonstrated that the new process can be used in roll-to-roll production.

Organic solar cells using a high-molecular-weight benzodithiophene-benzothiadiazole copolymer with an efficiency of 9.4%.

A high molecular weight donor-acceptor conjugated polymer is synthesized using the Suzuki polycondensation method. Using this polymer, a single-junction bulk-heterojunction solar cell is fabricated giving a power conversion efficiency of 9.4% using a fullerene-modified ZnO interlayer at the cathode contact.

Indan-1,3-dione electron-acceptor small molecules for solution-processable solar cells: a structure-property correlation.

A structure-device performance correlation in bulk heterojunction solar cells for new indandione-derived small molecule electron acceptors, FEHIDT and F8IDT, is presented. Devices based on the former exhibit higher power conversion efficiency (2.4%) and higher open circuit voltage, a finding consistent with reduced intermolecular interactions.