Manipulation of Gaseous Ions with Acoustic Fields at Atmospheric Pressure.

The ability to controllably move gaseous ions is an essential aspect of ion-based spectrometry (e.g., mass spectrometry and ion mobility spectrometry) as well as materials processing. At higher pressures, ion motion is largely governed by diffusion and multiple collisions with neutral gas molecules. Thus, high-pressure ion optics based on electrostatics require large fields, radio frequency drives, complicated geometries, and/or partially transmissive grids that become contaminated. Here, we demonstrate that low-power standing acoustic waves can be used to guide, block, focus, and separate beams of ions akin to electrostatic ion optics. Ions preferentially travel through the static-pressure regions ("nodes") while neutral gas does not appear to be impacted by the acoustic field structure and continues along a straight trajectory. This acoustic ion manipulation (AIM) approach has broad implications for ion manipulation techniques at high pressure, while expanding our fundamental understanding of the behavior of ions in gases.

MODERN PLASMA-BASED DESORPTION/IONIZATION: FROM ATOMS AND MOLECULES TO CHEMICAL SYNTHESIS.

Since the first mass spectrometry (MS) experiments were conducted by Thomson and Aston, plasmas have been used as ionization sources. Historically, plasma ion sources were used for these experiments because they were one of the few known sources of gas-phase ions at the time and they were relatively simple to setup and operate. Since then, developments in plasma ionization have continued to inform and motivate advances in other areas of MS. For example, plasma-desorption MS demonstrated ionization of large peptides and polymers more than 10 years before the first descriptions of electrospray ionization (ESI) and matrix-assisted laser desorption/ionization (MALDI). As a result, significant effort was placed on development of ionization approaches, mass analysis, and detection approaches for very large molecules: even before the advent of ESI and MALDI. Since then, new analytical challenges and opportunities in plasma ionization have arisen. In this review, the emerging trends in plasma-based ionization for several areas of MS will be discussed, including molecular ionization, elemental ionization, hybrid elemental and molecular ion sources, and unique chemical transformations. © 2020 John Wiley & Sons Ltd. Mass Spec Rev.

Unsupervised Reconstruction of Analyte-Specific Mass Spectra Based on Time-Domain Morphology with a Modified Cross-Correlation Approach.

Concomitant species that appear at the same or very similar times in a mass-spectral analysis can clutter a spectrum because of the coexistence of many analyte-related ions (e.g., molecular ions, adducts, fragments). One method to extract ions stemming from the same origin is to exploit the chemical information encoded in the time domain, where the individual temporal appearances inside the complex structures of chronograms or chromatograms differ with respect to analytes. By grouping ions with very similar or identical time-domain structures, single-component mass spectra can be reconstructed, which are much easier to interpret and are library-searchable. While many other approaches address similar objectives through the Pearson's correlation coefficient, we explore an alternative method based on a modified cross-correlation algorithm to compute a metric that describes the degree of similarity between features inside any two ion chronograms. Furthermore, an automatic workflow was devised to be capable of categorizing thousands of mass-spectral peaks into different groups within a few seconds. This approach was tested with direct mass-spectrometric analyses as well as with a simple, fast, and poorly resolved LC-MS analysis. Single-component mass spectra were extracted in both cases and were identified based on accurate mass and a mass-spectral library search.

Cooperative Heteroligand Interaction with G-Quadruplexes Shows Evidence of Allosteric Binding.

Although allosteric binding of small molecules is commonplace in protein structures, it is rather rare in DNA species such as G-quadruplexes. By using CD melting, here, we found binding of the small-molecule ligands PDS and L2H2-6OTD to the telomeric DNA G-quadruplex was cooperative. Mass spectrometry indicated a 1:1:1 ratio in the ternary binding complex of the telomeric G-quadruplex, PDS, and L2H2-6OTD. Compared to the binding of each individual ligand to the G-quadruplex, single-molecule mechanical unfolding assays revealed a significantly decreased dissociation constant when one ligand is evaluated in the presence of another. This demonstrates that cooperative binding of PDS and L2H2-6OTD to the G-quadruplex is allosteric, which is also supported by the mass spectra data that indicated the ejection of coordinated sodium ions upon binding of the heteroligands to the G-quadruplex. The unprecedented observation of the allosteric ligand binding to higher-ordered structures of DNA may help to design more effective ligands to target non-B DNA species involved in many critical cellular processes.

Ambient desorption/ionization mass spectrometry: evolution from rapid qualitative screening to accurate quantification tool.

In this article, some recent trends and developments in ambient desorption/ionization mass spectrometry (ADI-MS) are reviewed, with a special focus on quantitative analyses with direct, open-air sampling. Accurate quantification with ADI-MS is still not routinely performed, but this aspect is considered of utmost importance for the advancement of the field. In fact, several research groups are devoted to the development of novel and optimized ADI-MS approaches. Some key trends include novel sample introduction strategies for improved reproducibility, tailored sample preparation protocols for removing the matrix and matrix effects, and multimode ionization sources. In addition, there is significant interest in quantitative mass spectrometry imaging. Graphical abstract Conceptual diagram of the ambient desorption/ionization mass spectrometry approach with different desorption/ionization probes.

Tunable Ionization Modes of a Flowing Atmospheric-Pressure Afterglow (FAPA) Ambient Ionization Source.

Plasma-based ambient desorption/ionization sources are versatile in that they enable direct ionization of gaseous samples as well as desorption/ionization of analytes from liquid and solid samples. However, ionization matrix effects, caused by competitive ionization processes, can worsen sensitivity or even inhibit detection all together. The present study is focused on expanding the analytical capabilities of the flowing atmospheric-pressure afterglow (FAPA) source by exploring additional types of ionization chemistry. Specifically, it was found that the abundance and type of reagent ions produced by the FAPA source and, thus, the corresponding ionization pathways of analytes, can be altered by changing the source working conditions. High abundance of proton-transfer reagent ions was observed with relatively high gas flow rates and low discharge currents. Conversely, charge-transfer reagent species were most abundant at low gas flows and high discharge currents. A rather nonpolar model analyte, biphenyl, was found to significantly change ionization pathway based on source operating parameters. Different analyte ions (e.g., MH(+) via proton-transfer and M(+.) via charge-transfer) were formed under unique operating parameters demonstrating two different operating regimes. These tunable ionization modes of the FAPA were used to enable or enhance detection of analytes which traditionally exhibit low-sensitivity in plasma-based ADI-MS analyses. In one example, 2,2'-dichloroquaterphenyl was detected under charge-transfer FAPA conditions, which were difficult or impossible to detect with proton-transfer FAPA or direct analysis in real-time (DART). Overall, this unique mode of operation increases the number and range of detectable analytes and has the potential to lessen ionization matrix effects in ADI-MS analyses.

Pulse radiolysis and ultra-high-performance liquid chromatography/high-resolution mass spectrometry studies on the reactions of the carbonate radical with vitamin B12 derivatives.

The reactions of the carbonate radical anion (CO3 (.) (-) ) with vitamin B12 derivatives were studied by pulse radiolysis. The carbonate radical anion directly oxidizes the metal center of cob(II)alamin quantitively to give hydroxycobalamin, with a bimolecular rate constant of 2.0×10(9) M(-1) s(-1) . The reaction of CO3 (.) (-) with hydroxycobalamin proceeds in two steps. The second-order rate constant for the first reaction is 4.3×10(8) M(-1) s(-1) . The rate of the second reaction is independent of the hydroxycobalamin concentration and is approximately 3.0×10(3) s(-1) . Evidence for formation of corrinoid complexes differing from cobalamin by the abstraction of two or four hydrogen atoms from the corrin macrocycle and lactone ring formation has been obtained by ultra-high-performance liquid chromatography/high-resolution mass spectrometry (UHPLC/HRMS). A mechanism is proposed in which abstraction of a hydrogen atom by CO3 (.) (-) from a carbon atom not involved in the π conjugation system of the corrin occurs in the first step, resulting in formation of a Co(III) C-centered radical that undergoes rapid intramolecular electron transfer to form the corresponding Co(II) carbocation complex for about 50 % of these complexes. Subsequent competing pathways lead to formation of corrinoid complexes with two fewer hydrogen atoms and lactone derivatives of B12 . Our results demonstrate the potential of UHPLC combined with HRMS in the separation and identification of tetrapyrrole macrocycles with minor modifications from their parent molecule.

Antiferromagnetically Coupled Dimeric Dodecacopper Supramolecular Architectures of Macrocyclic Ligands with a Symmetrical µ6-BO3(3-) Central Moiety.

Reactions between 2,6-diformyl-4-alkyl(R)-phenol (R = CH3 or C(CH3)3) and 1,3-diamino-2-hydroxypropane (1,3-DAP) in the presence of copper(II) salts (Cu(BF4)2·6H2O, Cu(ClO4)2·6H2O/H3BO3/Ar) and triethylamine (TEA) in a single pot result in self-assembly of dimeric dodecacopper supramolecular architectures of 30-membered hexatopic macrocyclic ligands (H6L4 and H6L5) with unique and fascinating structures having the BO3(3-) anion as the central species bonded to all six copper centers in a symmetrical fashion (µ6-BO3(3-)). A number of closely related macrocyclic hexacopper complexes are reported: {[Cu6(L4)(µ6-BO3)(µ-H2O)(C3H7NO)2(BF4)][BF4]2·3C3H7NO}2 (1) (DMF = C3H7NO), {[Cu6(L4)(µ6-BO3)(µ-C3H7NO)3][ClO4]3·3C3H7NO}2 (2), {[Cu6(L5)(µ6-BO3)(µ-OH)(H2O)3(C3H7NO)][BF4]2·6C3H7NO·4C2H5OH·2H2O}2 (3), {[Cu6(L5)(µ6-BO3)(µ-CH3OH)(CH3OH)2][ClO4]3·10H2O}2 (4), and {[Cu6(L5)(µ6-BO3)(µ-CH3CO2)(µ-CH3O)(CH3OH)][BF4]·13CH3OH·8H2O}2 (5). A polymeric side product {[Cu2(H2L2)(CH3OH)(BF4)][BF4]}n (6), involving a 2 + 2 macrocyclic ligand, was also isolated and structurally characterized. Complex 6 involves dinuclear copper(II) units linked through BF4(-) anions to form a novel 1D single-chain polymeric coordination compound. This appears to be the first report in which a central BO3(3-) species is linked to six copper(II) ions held together by a single macrocyclic ligand through three µ1,1-O(BO3(3-)) and three µ1,3-O(BO3(3-)) bridges. In complexes 1-5 the BO3(3-) is present in the center of the macrocyclic cavity and is bonded to all six metal centers arranged in a benzene-like hexagonal array. In the hexagonal array there are alternate double (µ-alkoxide and µ1,3-O(BO3(3-))) and (µ-phenoxide and µ1,1-O(BO3(3-))) bridges between the Cu(II) centers. The symmetrical hexa-bridging nature of µ6-BO3(3-) is unprecedented in transition metal complex chemistry, and along with alkoxide and phenoxide bridges in the equatorial plane provides effective pathways for an overall antiferromagnetic exchange interaction between six copper(II) centers. In 1, 3, and 5 the BO3(3-) moiety is produced in one step (synthetic) by an unusual copper(II)-macrocycle complex catalyzed hydrolysis of BF4(-) ion in methanol. In 2 and 4 the central species (BO3(3-)) comes from boric acid (H3BO3) which is added to reaction mixture of Cu(ClO4)2/H6L4/H6L5 under inert conditions to confirm the identity of the central species.

Autonomous in situ analysis and real-time chemical detection using a backpack miniature mass spectrometer: concept, instrumentation development, and performance.

A major design objective of portable mass spectrometers is the ability to perform in situ chemical analysis on target samples in their native states in the undisturbed environment. The miniature instrument described here is fully contained in a wearable backpack (10 kg) with a geometry-independent low-temperature plasma (LTP) ion source integrated into a hand-held head unit (2 kg) to allow direct surface sampling and analysis. Detection of chemical warfare agent (CWA) simulants, illicit drugs, and explosives is demonstrated at nanogram levels directly from surfaces in near real time including those that have complex geometries, those that are heat-sensitive, and those bearing complex sample matrices. The instrument consumes an average of 65 W of power and can be operated autonomously under battery power for ca. 1.5 h, including the initial pump-down of the manifold. The maximum mass-to-charge ratio is 925 Th with mass resolution of 1-2 amu full width at half-maximun (fwhm) across the mass range. Multiple stages of tandem analysis can be performed to identify individual compounds in complex mixtures. Both positive and negative ion modes are available. A graphical user interface (GUI) is available for novice users to facilitate data acquisition and real-time spectral matching.

Plasma-based ambient desorption/ionization mass spectrometry: state-of-the-art in qualitative and quantitative analysis.

Ambient desorption/ionization mass spectrometry (ADI-MS) aims to enable direct analysis of gaseous, liquid, and/or solid samples under ambient conditions. In ADI-MS, different types of desorption/ionization sources are classified according to their basic method of operation, namely spray-based, laser-based, or plasma-based. This review discusses many of the plasma-based techniques coupled to mass spectrometry in terms of their current performance in fast qualitative screening and quantitative analysis. Critical aspects, for example sample preparation and introduction, quantification, and matrix effects, are addressed. Furthermore, the applicability of plasma-based sources to portable mass spectrometers and their capabilities in imaging experiments are summarized. The applications discussed are of two types. In one, direct screening is performed without any or with minimal sample pretreatment. Samples with low matrix content are qualitatively analyzed without interferences. The other, more challenging applications, namely samples with high matrix content and most quantitative analysis, typically require sample preparation ranging from simple dilution to extensive multi-step procedures.

Handheld low-temperature plasma probe for portable "point-and-shoot" ambient ionization mass spectrometry.

We describe a handheld, wireless low-temperature plasma (LTP) ambient ionization source and its performance on a benchtop and a miniature mass spectrometer. The source, which is inexpensive to build and operate, is battery-powered and utilizes miniature helium cylinders or air as the discharge gas. Comparison of a conventional, large-scale LTP source against the handheld LTP source, which uses less helium and power than the large-scale version, revealed that the handheld source had similar or slightly better analytical performance. Another advantage of the handheld LTP source is the ability to quickly interrogate a gaseous, liquid, or solid sample without requiring any setup time. A small, 7.4-V Li-polymer battery is able to sustain plasma for 2 h continuously, while the miniature helium cylinder supplies gas flow for approximately 8 continuous hours. Long-distance ion transfer was achieved for distances up to 1 m.

Halo-shaped flowing atmospheric pressure afterglow: a heavenly design for simplified sample introduction and improved ionization in ambient mass spectrometry.

The flowing atmospheric-pressure afterglow (FAPA) is a promising new source for atmospheric-pressure, ambient desorption/ionization mass spectrometry. However, problems exist with reproducible sample introduction into the FAPA source. To overcome this limitation, a new FAPA geometry has been developed in which concentric tubular electrodes are utilized to form a halo-shaped discharge; this geometry has been termed the halo-FAPA or h-FAPA. With this new geometry, it is still possible to achieve direct desorption and ionization from a surface; however, sample introduction through the inner capillary is also possible and improves interaction between the sample material (solution, vapor, or aerosol) and the plasma to promote desorption and ionization. The h-FAPA operates with a helium gas flow of 0.60 L/min outer, 0.30 L/min inner, and applied current of 30 mA at 200 V for 6 W of power. In addition, separation of the discharge proper and sample material prevents perturbations to the plasma. Optical-emission characterization and gas rotational temperatures reveal that the temperature of the discharge is not significantly affected (<3% change at 450 K) by water vapor during solution-aerosol sample introduction. The primary mass-spectral background species are protonated water clusters, and the primary analyte ions are protonated molecular ions (M + H(+)). Flexibility of the new ambient sampling source is demonstrated by coupling it with a laser ablation unit, a concentric nebulizer, and a droplet-on-demand system for sample introduction. A novel arrangement is also presented in which the central channel of the h-FAPA is used as the inlet to a mass spectrometer.

Arrays of low-temperature plasma probes for ambient ionization mass spectrometry.

RATIONALE: This paper reports the development of arrays of capillary-based low-temperature plasma (LTP) probes for direct sample analysis. These probe arrays allow a higher surface area to be analyzed, increasing the throughput in large sample analysis. Validation of these arrays was performed on illicit, cathinone-based drugs marketed as 'bath salts'. METHODS: LTP arrays consisting of 1, 7, and 19 probes were constructed with quartz capillaries and held together with silver epoxy resin adhesive. Three drugs, mephedrone, methylone and methylenedioxypyrovalerone, were analyzed with each plasma ion source and an ion trap mass spectrometer in full MS and in MS/MS positive ion mode. Chemical and thermal footprints were determined for each source. A reactive probe design was used to inject trifluoroacetic anhydride directly into the plasma stream for on-line derivatization. RESULTS: Small LTP probes and bundled arrays provide low picogram level limits of detection for mephedrone, methylone and methylenedioxypyrovalerone. Bundling the probes together in larger arrays increases the surface area analyzed by a factor of ten, while maintaining surface temperatures below 40 °C. Selectivity towards mephedrone and methylone was increased using trifluoracetylation under ambient ionization conditions. CONCLUSIONS: Low-temperature plasma ionization sources allow rapid detection of illicit 'bath salt' drugs in low amounts. The sources have a larger sampling area that allows faster detection of each analyte, and selectivity towards the selected drug is enhanced by adding reagents directly into the plasma stream.

Characterization of a Low-Temperature Plasma (LTP) Ambient Ionization Source Using Temporally Resolved Monochromatic Imaging Spectrometry.

The low-temperature plasma (LTP) probe is a common plasma-based source used for ambient desorption-ionization mass spectrometry (MS). While the LTP probe has been characterized in detail with MS, relatively few studies have used optical spectroscopy. In this paper, two-dimensional (2D) imaging at selected wavelengths is used to visualize important species in the LTP plasma jet. First, 2D steady-state images of the LTP plume for N2+ (391.2 nm), He I (706.5 nm), and N2 (337.1 nm) emissions were recorded under selected plasma conditions. Second, time-resolved 2D emission maps of radiative species in the LTP plasma jet were recorded through the use of a 200 ns detection gate and varying gate delays with respect to the LTP trigger pulse. Emission from He I, N2+, and N2 in the plasma jet region was found to show a transient behavior (often referred to as plasma bullets) lasting only a few microseconds. The N2+ and He I maps were highly correlated in spatial and temporal structure. Further, emission from N2 showed two maxima in time, one before and one after the maximum emission for N2+ and He I, due to an initial electronic excitation wave and ion-electron recombination, respectively. Third, the interaction of the LTP probe with a sample substrate and an electrically grounded metallic needle was studied. Emission from a fluorophore on the sample substrate showed an initial photon-induced excitation from plasma-generated photons followed by electronic excitation by other plasma species. The presence of a grounded needle near the plasma jet significantly extended the plasma jet lifetime and also generated a long-lived corona discharge on the needle. The effect of LTP operating parameters on emission spectra was correlated with mass-spectral results including reagent-ion signals. Lastly, five movies provide a side-by-side comparison of the temporal behavior of emitting species and insights into the interactions of the emission clouds with a sample surface as well as an external needle. Temporally and spatially resolved imaging provided insights into important processes in the LTP plasma jet, which will help improve analyte ion sampling in LTP-MS.

Drop-on-demand sample introduction system coupled with the flowing atmospheric-pressure afterglow for direct molecular analysis of complex liquid microvolume samples.

One of the fastest developing fields in analytical spectrochemistry in recent years is ambient desorption/ionization mass spectrometry (ADI-MS). This burgeoning interest has been due to the demonstrated advantages of the method: simple mass spectra, little or no sample preparation, and applicability to samples in the solid, liquid, or gaseous state. One such ADI-MS source, the flowing atmospheric-pressure afterglow (FAPA), is capable of direct analysis of solids just by aiming the source at the solid surface and sampling the produced ions into a mass spectrometer. However, direct introduction of significant volumes of liquid samples into this source has not been possible, as solvent loads can quench the afterglow and, thus, the formation of reagent ions. As a result, the analysis of liquid samples is preferably carried out by analyzing dried residues or by desorbing small amounts of liquid samples directly from the liquid surface. In the former case, reproducibility of sample introduction is crucial if quantitative results are desired. In the present study, introduction of liquid samples as very small droplets helps overcome the issues of sample positioning and reduced levels of solvent intake. A recently developed "drop-on-demand" (DOD) aerosol generator is capable of reproducibly producing very small volumes of liquid (∼17 pL). In this paper, the coupling of FAPA-MS and DOD is reported and applications are suggested. Analytes representing different classes of substances were tested and limits of detections were determined. Matrix tolerance was investigated for drugs of abuse and their metabolites by analyzing raw urine samples and quantification without the use of internal standards. Limits of detection below 2 µg/mL, without sample pretreatment, were obtained.

Ultrasensitive ambient mass spectrometric analysis with a pin-to-capillary flowing atmospheric-pressure afterglow source.

The advent of ambient desorption/ionization mass spectrometry has resulted in a strong interest in ionization sources that are capable of direct analyte sampling and ionization. One source that has enjoyed increasing interest is the flowing atmospheric-pressure afterglow (FAPA). The FAPA has been proven capable of directly desorbing/ionizing samples in any phase (solid, liquid, or gas) and with impressive limits of detection (<100 fmol). The FAPA was also shown to be less affected by competitive-ionization matrix effects than other plasma-based sources. However, the original FAPA design exhibited substantial background levels, cluttered background spectra in the negative-ion mode, and significant oxidation of aromatic analytes, which ultimately compromised analyte identification and quantification. In the present study, a change in the FAPA configuration from a pin-to-plate to a pin-to-capillary geometry was found to vastly improve performance. Background signals in positive- and negative-ionization modes were reduced by 89% and 99%, respectively. Additionally, the capillary anode strongly reduced the amount of atomic oxygen that could cause oxidation of analytes. Temperatures of the gas stream that interacts with the sample, which heavily influences desorption capabilities, were compared between the two sources by means of IR thermography. The performance of the new FAPA configuration is evaluated through the determination of a variety of compounds in positive- and negative-ion mode, including agrochemicals and explosives. A detection limit of 4 amol was found for the direct determination of the agrochemical ametryn and appears to be spectrometer-limited. The ability to quickly screen for analytes in bulk liquid samples with the pin-to-capillary FAPA is also shown.

Elucidation of reaction mechanisms responsible for afterglow and reagent-ion formation in the low-temperature plasma probe ambient ionization source.

The development of ambient desorption/ionization mass spectrometry has shown promising applicability for the direct analysis of complex samples in the open, ambient atmosphere. Although numerous plasma-based ambient desorption/ionization sources have been described in the literature, little research has been presented on experimentally validating or determining the desorption and ionization mechanisms that are responsible for their performance. In the present study, established spectrochemical and plasma physics diagnostics in combination with spatially resolved optical emission profiles were applied to reveal a set of reaction mechanisms responsible for afterglow and reagent-ion formation of the Low-Temperature Plasma (LTP) probe, which is a plasma-based ionization source used in the field of ambient mass spectrometry. Within the dielectric-barrier discharge of the LTP probe, He(2)(+) is the dominant positive ion when helium is used as the plasma supporting gas. This helium dimer ion (He(2)(+)) has two important roles: First, it serves to carry energy from the discharge into the afterglow region in the open atmosphere. Second, charge transfer between He(2)(+) and atmospheric nitrogen appears to be the primary mechanism in the sampling region for the formation of N(2)(+), which is an important reagent ion as well as the key reaction intermediate for the formation of other reagent ions, such as protonated water clusters, in plasma-based ambient ionization sources. In the afterglow region of the LTP, where the sample is usually placed, a strong mismatch in the rotational temperatures of N(2)(+) (B (2)Σ(u)(+)) and OH (A (2)Σ(+)) was found; the OH rotational temperature was statistically identical to the ambient gas temperature (~300 K) whereas the N(2)(+) temperature was found to rise to 550 K toward the tail of the afterglow region. This much higher N(2)(+) temperature is due to a charge-transfer reaction between He(2)(+) and N(2), which is known to produce rotationally hot N(2)(+) (B (2)Σ(u)(+)) ions. Furthermore, it was found that one origin of excited atomic helium in the afterglow region of the LTP is from dielectronic recombination of vibrationally excited He(2)(+) ions.

Fast transient analysis and first-stage collision-induced dissociation with the flowing atmospheric-pressure afterglow ionization source to improve analyte detection and identification.

The recent development of ambient desorption/ionization mass spectrometry (ADI-MS) has enabled fast, simple analysis of many different sample types. The ADI-MS sources have numerous advantages, including little or no required sample pre-treatment, simple mass spectra, and direct analysis of solids and liquids. However, problems of competitive ionization and limited fragmentation require sample-constituent separation, high mass accuracy, and/or tandem mass spectrometry (MS/MS) to detect, identify, and quantify unknown analytes. To maintain the inherent high throughput of ADI-MS, it is essential for the ion source/mass analyzer combination to measure fast transient signals and provide structural information. In the current study, the flowing atmospheric-pressure afterglow (FAPA) ionization source is coupled with a time-of-flight mass spectrometer (TOF-MS) to analyze fast transient signals (<500 ms FWHM). It was found that gas chromatography (GC) coupled with the FAPA source resulted in a reproducible (<5% RSD) and sensitive (detection limits of <6 fmol for a mixture of herbicides) system with analysis times of ca. 5 min. Introducing analytes to the FAPA in a transient was also shown to significantly reduce matrix effects caused by competitive ionization by minimizing the number and amount of constituents introduced into the ionization source. Additionally, MS/MS with FAPA-TOF-MS, enabling analyte identification, was performed via first-stage collision-induced dissociation (CID). Lastly, molecular and structural information was obtained across a fast transient peak by modulating the conditions that caused the first-stage CID.

Plasma-Based Ambient Desorption/Ionization Mass Spectrometry for the Analysis of Liquid Crystals Employed in Display Devices.

Liquid-crystal displays (LCDs) are the most frequently used display technology worldwide these days. Due to the rather complex manufacturing process and purity requirements for the chemicals used, quality control and display failure analysis are important analytical tasks. Currently, the state-of-the-art techniques (e.g., high-performance liquid chromatography (HPLC), gas chromatography (GC) coupled to mass spectrometry (MS), time-of-flight secondary ion mass spectrometry (TOF-SIMS), or high-resolution microscopy) are costly and time-consuming. Hence, a new pathway to precisely analyze liquid-crystalline materials and LCDs in their native state is reported. A new approach for direct analysis via plasma-based ambient desorption/ionization mass spectrometry (ADI-MS) offers an inexpensive and faster alternative. In this study, direct analysis in real time (DART), the low-temperature plasma (LTP) probe, and flowing atmospheric-pressure afterglow (FAPA) ADI sources coupled to high-resolution mass spectrometry (HR-MS) are compared based on their capabilities and performance for liquid-crystal analysis. These sources enable direct analyte desorption from a sample surface at ambient conditions and ionize the vaporized analyte molecules in a subsequent step. Primarily, the ionization capabilities of the three ADI sources are compared for individual liquid-crystal standards, mixtures of liquid crystals (LCs), and complex liquid crystal/additive mixtures applied in commercially available LCDs. Furthermore, direct surface analysis from a glass substrate is also performed with ADI-MS to compare their applicability to this type of sample matrix.