Influence of adding nanoparticles on the hardness, tear strength, and permanent deformation of facial silicone subjected to accelerated aging.

STATEMENT OF PROBLEM: The efficiency of adding nanoparticles to silicone protection has proven to prevent color degradation. However, reports of other physical property changes in facial silicone are scarce. PURPOSE: The purpose of this in vitro study was to evaluate the influence of adding nanoparticles on the hardness, tear strength, and permanent deformation of a facial silicone. MATERIAL AND METHODS: Specimens were made for each test, with 140 for the hardness test, 140 for the permanent deformation test, but 280 for the rupture test. This higher number was due to the fact that the first 140 specimens were ruptured and unusable after the initial reading. ZnO, BaSO4, and TiO2 nanoparticles at concentrations of 1% and 2% of silicone were used, as well as specimens without nanoparticles that consisted of only oil paint and of only silicone. Outcomes were measured before and after 1008 hours of accelerated aging. Data were analyzed by nested analysis of variance (ANOVA) and Tukey honest significant differences test (α=.05). RESULTS: Results showed that the presence of nanoparticles influenced the properties of the assessed groups. The nanoparticles decreased hardness values. The highest values of tear strength were observed for the groups with addition of BaSO4. The 1% ZnO group without oil paint showed the lowest values of permanent deformation. CONCLUSIONS: Based on the findings of this in vitro study, the use of ZnO nanoparticles is recommended, since they did not negatively affect the properties of the materials evaluated.

Development of nanobiosilicate, tricalcium phosphate and chlorhexidine materials for biomineralization with crystallographic similarity to hydroxyapatite and biomodified collagen.

OBJECTIVES: The aim of this work is to test experimental cements, doped with a silicate based bioactive nanoparticle (NanoBiosilicate). Methods, we synthesized a glass nanoparticle by Sol-Gel Stöber method, used to be incorporated in a dental material for endodontic uses. MATERIALS AND METHODS: We assess the mineralizing properties and biocompatibility. Besides the crystallography characterization of the resultant new crystals. Results, After analysis, and comparison with commercial materials, the material tested was similar in mechanical properties required by ISO, The ion release was effective after 2 hr. of setting and the novel material was cell compatible accepted by ISO. RESULTS: We found new formed Calcium Phosphate peaks in the spectroscopic analysis (FTIR), remarkably the crystals formed were comparable to hydroxyapatite when analyzed with a Selected Area Electron Diffractometer, with rings of 2.84 Å for 002, and the 2.77 Å is also visible for 210. The 6.83 Å and 6.88 Å, for respective 222 and 004. The incorporation of Chlorhexidine was not detrimental for this property, Significance, the features mentioned represented a progress in biomineralization field that was associated to an improved mineral structure formation with increased crystallographic similarity to natural hydroxyapatite. When chlorhexidine was added a favorable biomodification of the remaining collagen in dentinal walls and antimicrobial activity potential were also observed.

Effect of repeated microwave disinfections on bonding of different commercial teeth to resin denture base.

OBJECTIVE: To verify the influence of repeated microwave disinfections on the shear bond strength of two commercial types of teeth to acrylic resin, when the ridge lap surfaces were unmodified, bur abraded, bur grooved or etched by monomer. MATERIAL AND METHODS: Eighty specimens (n = 10) were adhered to the tooth ridge lap surface, polymerised in a water bath at 74°C for 9 h. Microwaved specimens were individually immersed in 150 ml of water and submitted to five simulated disinfections in a microwave oven calibrated at 650 W for 3 min. Control specimens were not microwave treated. Shear bond strength tests were performed in an Instron machine with a cross-speed of 1 mm/min. The fracture load values were transformed into shear bond strength as a function of the bonding area (0.28 cm(2)). Data were submitted to ANOVA and Tukey's test (α = 0.05). Fractured areas were classified as adhesive, cohesive (resin or tooth) or mixed failures. RESULTS: Repeated microwave disinfections increased the shear strength of the tooth/resin bond. Mechanical retention in microwaved and non-microwaved procedures improved the shear bond strength. CONCLUSIONS: The different commercial types of teeth influenced shear bond strength values, with Biotone teeth showing the lower values.

Effect of polymerization techniques on vertical dimension and tooth position in complete dentures.

Due to the changes in the composition and processing of acrylic resins, it seems appropriate to evaluate the influence of polymerization methods about the alteration of occlusal vertical dimension and the horizontal positioning of artificial teeth of total dentures. For this, 64 specimens were made, simulating a maxillary total denture waxed from a standard maxillary denture. The experimental samples were divided into two groups: Group 1 - The resins were submitted to polymerization in a hot water bath, Group 2 - The same resins were submitted to poly-merization by microwave energy. The samples were measured horizontally and vertically before and after the polymerization process. Based on the results, it can be concluded that there was no statistically significant difference between the conventional polymerization method and the polymerization method by microwave, related to the stability of occlusal vertical dimension and horizontal positioning of artificial teeth on the specimens evaluated.

Effect of Tricalcium Silicate on Direct Pulp Capping: Experimental Study in Rats.

OBJECTIVES: Conduct a histological comparison of the pulp response to different materials, with a focus on the continuity and morphology of the mineralized barrier after direct pulp capping. MATERIALS AND METHODS: One hundred and eight maxillary first molars of 54 Wistar rats were subject to direct pulp capping and divided into three groups according to the materials used: calcium hydroxide (CH), mineral trioxide aggregate (MTA), and Biodentine. All cavities were sealed, and the animals were euthanized at 7, 14, and 21 days. Descriptive histological evaluation of the inflammation and formation of the mineralized barrier was performed. STATISTICAL ANALYSIS: Statistical analyses were performed using the Kruskal-Wallis test, which was complemented by the Dunn test; differences with p < 0.05 were considered statistically significant. RESULTS: The results showed that MTA and Biodentine elicited less intense inflammatory reactions than CH. With respect to the formation and quality of the dentin barrier formed, differences were observed at 21 days between the analyzed groups; the best results being obtained following treatment with MTA and Biodentine. CONCLUSION: MTA and Biodentine induced formation of a more continuous and uniform mineralized barrier with less intense pulp response than CH.

Influence of opacifiers on dimensional stability and detail reproduction of maxillofacial silicone elastomer.

BACKGROUND: We evaluated the influence of chemical disinfection and accelerated aging on the dimensional stability and detail reproduction of a silicone elastomer containing one of two opacifiers. METHODS: A total of 90 samples were fabricated from Silastic MDX 4-4210 silicone and divided into groups (n = 10) according to opacifier content (barium sulfate or titanium dioxide) and disinfectant solution (neutral soap, Efferdent, or 4% chlorhexidine). The specimens were disinfected 3 times per week during 60 days and then subjected to accelerated aging for 1008 hours. Dimensional stability and detail reproduction tests were performed after specimens' fabrication (baseline), chemical disinfection and periodically during accelerated aging (252, 504, and 1008 hours). The results were analyzed using 3-way repeated-measures ANOVA and the Tukey HSD test (α = 0.05). RESULTS: All groups exhibited dimensional changes over time. The opacifier (p = .314), period (p < .0001) and their interactions (p = .0041) affected the dimensional stability of the silicone. Statistical significant dimensional differences occurred between groups with (0.071) and without opacifiers (0.053). Accelerated aging influenced the dimensional stability of the samples. All groups scored 2 in the detail reproduction tests, which represents the fully reproducing of three test grooves with accurate angles. CONCLUSIONS: Incorporation of opacifiers alters the dimensional stability of silicones used in facial prosthetics, but seems to have no influence on detail reproduction. Accelerated aging is responsible for most of the dimensional changes in Silastic MDX4 4210, but all dimensional changes measured in this study remained within the limits of stability necessary for this application.

Effect of flask closure method and post-pressing time on the upper denture base adaptation.

OBJECTIVES: The purpose of this study was to evaluate the effect of flask-closure methods, post-pressing times and acrylic resins on denture base adaptation. MATERIALS AND METHODS: The resins were flasked using a hydraulic press and closed with the traditional clamp or RS system. Conventional heat-cure resin was polymerised immediately or at 6 h post-pressing at 74 degrees C for 9 h. Rapid cycle heat-cure resin was polymerised in boiling water for 20 min. After cooling, the bases were deflasked and the sets of cast-base transversally sectioned in the regions distal to the canine, mesial to the first molar and in the posterior palatal zone. The adaptation was measured with an optical microscope (0.0005 mm) at five reference points for each section. Data were analysed using anova and Tukey's test (alpha = 0.05). RESULTS: Traditional clamp and immediate post-pressing time improved base adaptation for conventional heat-cure resin. Both post-pressing times showed most accurate base adaptation for conventional heat-cure resin when the traditional clamp was used. Immediate post-pressing time improved base adaptation for conventional heat-cure resin and the 6-h delay in time was significant for the rapid cycle heat-cure resin. CONCLUSIONS: Traditional clamp and immediate post-pressing time improved base adaptation for conventional heat-cure resin.

Bonding Strength of Luting Cement to Zirconia-Based Ceramic Under Different Surface Treatments.

OBJECTIVES: The aim of this study was to evaluate the bonding strength of self-adhesive luting cement to zirconia under different surface treatments. MATERIALS AND METHODS: Thirty-two zirconia samples were randomly divided into eight experimental groups based on the surface treatment employed (Control: no surface treatment; PMM: wear with diamond bur; JAT: blasting with glass beads; PMA: wear with a medium-roughness milling machine; Primer: primer application on the surface without treatment; PMM +Primer: PMM treatment plus primer application; JAT+Primer: JAT treatment plus primer application; and PMA+Primer: PMA treatment plus primer application). Cement cylinders were built on the ceramic surfaces, and the groups were subdivided according to the storage time employed (i.e., 24 hours or 60 days). After storage, the samples were subjected to microshear testing. STATISTICAL ANALYSIS: The Kruskal-Wallis test followed by the Dunn test was employed for comparison between the groups (p < 0.05). RESULTS: The PMM group yielded the optimal results and the mean values increased after both storage times following the primer application. The Control, PMA, and JAT groups gave similar results after 24 hours, while the JAT group gave superior results following primer application over this storage time. After 60 days of storage, all groups gave improved results following chemical treatment with a primer. CONCLUSION: It was concluded that mechanical preparation using the diamond bur followed by primer application significantly improved the bond strength between the ceramic and the luting cement.

Degradation of Adhesive-Dentin Interfaces Created Using Different Bonding Strategies after Five-year Simulated Pulpal Pressure.

PURPOSE: To compare after five-year simulated pulpal pressure (SPP) the degradation of adhesive-dentin interfaces created using two simplified adhesives applied with different bonding strategies. MATERIALS AND METHODS: A two-step self-etch (CSE: Clearfil SE Bond) adhesive was used as a control multistep adhesive. The tested experimental materials were two simplified adhesives, a one-step self-etch (CS3: Clearfil S3 Bond) and a self-priming etch-and-rinse adhesive (SB2: Adper Single-Bond 2). Half of the bonded specimens were submitted to microtensile bond strength (µTBS) testing after 24 h. The other half submitted to SPP for five years before µTBS testing. Nonfractured sticks were evaluated using transmission electron microscopy (TEM). Scanning electron microscopy (SEM) was used to evaluate silver-nitrate nanoleakage within the interface. Data were statistically analyzed by two-way ANOVA and Tukey's test (p < 0.05). RESULTS: Prolonged SPP induced bond-strength reduction for both SB2 and CS3. All bonding approaches showed increased nanoleakage after aging. The two simplified adhesives showed severe degradation at the resin-dentin interface. TEM revealed that the main degradation patterns for the etch-and-rinse adhesive SB2 was collagen breakdown, while polymer hydrolysis along with filler debonding was mainly observed in CS3. CONCLUSIONS: Simplified adhesives applied in etch-and-rinse mode are mainly characterized by hydrolysis and collagen degradation. In self-etch mode, simplified adhesives may principally show hydrolysis of the polymeric matrix and/or at the interface of fillers and coupling agent. The use of multistep self-etching adhesives may guarantee greater dentin bond durability compared to simplified adhesives.

Cross-link density evaluation through softening tests: effect of ethanol concentration.

OBJECTIVES: The aim of this study was to investigate whether the ethanol concentration used would influence the outcomes obtained through softening tests when comparing light-activation modes. METHODS: Disc specimens (n=20) of Filtek Z250 and Filtek Z100 (3M ESPE) were light activated by standard (S) and pulse-delay (PD) modes. Initial Knoop hardness (KHN) measurements were performed 24h after dry storage at 37 degrees C. Half of the specimens (n=10) of each resin-composite were stored in absolute ethanol (100%) and the other half in 75% ethanol solution, for 24h at room temperature, and KHN was determined anew. Initial hardness data were submitted to Student's t-test (p=0.05). Percentages of hardness decrease were analyzed by two-way ANOVA followed by pairwise Tukey's test (p=0.05). The statistical analyses were performed separately for each resin-composite. RESULTS: No statistically significant differences were observed between standard and pulse-delay modes for initial Knoop hardness values. After storage in 75% ethanol solution, KHN was decreased in all cases but no significant differences were detected between light-activation modes (Filtek Z250: PD=12.6%, S=13.5%; Filtek Z100: PD=13.5%, S=11.8%) regardless of the resin-composite tested. After absolute ethanol storage, higher decrease in KHN were observed. Samples light-activated by the PD mode (Filtek Z250=20.4% and Filtek Z100=16.9%) exhibited significantly higher percentage decrease of KHN than specimens light-activated by the standard mode (Filtek Z250=14.1% and Filtek Z100=8.8%), regardless of the resin-composite tested. CONCLUSION: The ethanol concentration affected the outcomes of the softening test.

The influence of 30-day-old Streptococcus mutans biofilm on the surface of esthetic restorative materials--an in vitro study.

OBJECTIVE: To evaluate the effects of Streptococcus mutans biofilm/restorative materials interaction on surface roughness, hardness and morphology of materials tested. METHODS: Empress 2 (E2), Filtek Supreme (FS), Vitremer (V) and Ketac Molar Easymix (KM) were tested. Twenty-five disks of each material were made and divided into three storage groups: (1) 100% relative humidity (n=5); (2) growth medium (BHI and 1% sucrose) (n=5); (3) S. mutans biofilm-growth medium (n=15). Before storage, hardness measurements were immediately obtained from group 1 specimens. After 30 days of storage, the specimens were cleaned in order to obtain the surface roughness and hardness values, besides morphology analysis by scanning electron microscopy. RESULTS: The surface roughness and hardness values obtained from E2 and FS specimens did not present statistically significant differences among the groups 1, 2 and 3 and between immediate and 30-day-old specimens of each material. However, group 3 specimens of V and KM showed statistically significant higher surface roughness means than other groups. Group 1 specimens of V and KM also showed higher hardness values than the immediate values. Group 3 specimens of V presented decreased hardness values compared with other groups. The scanning electron micrographs showed an increase in surface degradation from group 1 to group 3 for FS, V and KM. CONCLUSIONS: Thirty-day-old biofilm promotes a negative effect on the surface morphology of FS, V and KM, on the surface roughness of V and KM and on the hardness of V.

In-depth polymerization of dual-cured resin cement assessed by hardness.

This study investigates the in-depth polymerization of dual-cured resin cement (Enforce; Dentsply, shades A2, B1, and opaque). Cylindrical specimens are obtained by photo-activation through ceramic. Control samples are light-cured without using ceramic. Samples are tested after 15 min or 24 h. Knoop hardness readings are made at 100, 300, 500, and 700 microm depth. Hardness is generally dependent on the mode of activation and post-cure time. Shades A2 and B1 show higher hardness values than opaque resin. Hardness at 100 microm is higher than at 700 microm. A linear relationship between hardness and depth is observed.

Effects of ceramic thickness and curing unit on light transmission through leucite-reinforced material and polymerization of dual-cured luting agent.

This study investigated the influence of ceramic thickness and curing unit on light transmission through leucite-reinforced material and polymerization of a dual-cured resin luting agent. Discs of Empress Esthetic (Ivoclar Vivadent) of 0.7-, 1.4- and 2-mm thickness were prepared. Variolink II (Ivoclar Vivadent) was placed in a 1-mm-thick cylindrical mold, and light-activated through ceramic for 40 s, using QTH or LED units. The samples were divided into dual, light, and chemically-polymerized control groups. Knoop hardness indentations were made on the top and bottom surfaces. Data were subjected to split-plot design three-way ANOVA and Tukey's test (P < 0.05). The light spectrum transmitted through ceramic was obtained using a spectrometer. Samples activated through 1.4-and 2-mm-thick discs showed lower hardness than all others groups, except for the chemical control group. Dual and light-polymerized control samples showed similar hardness to those activated through the 0.7-mm ceramic, whereas chemically polymerized control samples showed similar hardness to those activated through 1.4- and 2-mm ceramics. No significant differences in hardness were detected between the curing units or between the top and bottom layers. No significant alteration in the light spectrum profile was observed for both units, irrespective of the ceramic thickness.

Influence of the light curing unit and thickness of residual dentin on generation of heat during composite photoactivation.

The aim of this study was to determine the effect of different types of composites (Filtek Z250, Esthet X and Filtek Supreme) and dentin thicknesses (0.5 or 1.0 mm) on the generation of heat during photoactivation by QTH (conventional halogen light), LED (light emitting diode), and PAC (xenon plasma light) light-curing units. Temperature changes were recorded with a thermocouple type K connected to a digital thermometer. Twenty chemically polymerized acrylic resin bases were prepared in order to guide the thermocouple and to support the dentin disks. On the acrylic resin base, elastomer molds of 2.0-mm thickness were adapted. The temperature increase was measured after composite photoactivation and the matrix was stored at 37 degrees C. After 24 hours, photoactivation was performed again and the temperature increase was measured. Obtained data were analyzed by ANOVA and Tukey's test (alpha= 0.05). The mean temperature increase produced by QTH was significantly lower than that of the other photoactivating units (P < 0.05), due to its low radiant exposure. There were no significant differences among the samples with regard to dentin thickness and type of composites (P > 0.05). The immediate temperature rise was statistically higher when compared to the increase after additional polymerization (24 h), in all groups (P < 0.05). Light intensity and exposure time appeared to be the most important factors causing temperature change.

Solubility and dimensional change after setting of root canal sealers: a proposal for smaller dimensions of test samples.

This study proposed smaller dimensions for samples used in solubility and dimensional change tests of root filling materials on the basis of American National Standard Institute/American Dental Association (ANSI/ADA) Specification No. 57. The volume, mass, and density of the test samples were determined, and 6 different samples of smaller dimensions were proposed for each test. Endofill and AH Plus sealers were used in the tests. For the solubility test, 2 samples were weighted, stored in distilled and dionized water for 24 hours, dried, and weighed again. Solubility was calculated by using samples' weight loss (%). For dimensional change analysis, the samples' heights were measured before and after immersion in dionized water for 30 days. For both tests, correlation between data of the different groups was observed. Kruskal-Wallis test showed that Endofill sealer presented higher solubility values than AH Plus (P < .05). The Endofill sealer presented 0.56% of shrinkage and AH Plus 0.62% expansion. Smaller dimensions for test samples used in solubility and dimensional change tests are a viable alternative, decreasing the amount of filling material necessary for executing these tests.

Modulated photoactivation methods--effect on marginal and internal gap formation of restorations using different restorative composites.

UNLABELLED: This study evaluated the effect of modulated photoactivation methods on gap formation of restorations using different composites. METHODS: Sixty human third molars were selected, sectioned (two fragments), and ground to expose a flat enamel area. A cavity (5 mm long x 2 mm wide x 2 mm deep--outer margins in enamel and inner margins in dentin) was prepared on the central area of flattened surface. Single bond adhesive system was applied according to manufacturer's instructions. The specimens were assigned into 12 groups (n = 10), according to the restorative composite (Filtek Z250, Herculite XRV, and Heliomolar) and the photoactivation method [continuous light (CL); soft-start (SS); pulse delay (PD); and intermittent light (IL)]. Outer margins were stained using Caries Detector, observed under stereomicroscope, and images were transferred to a computer measurement program. Then, the specimens were sectioned in slices and the internal gaps were assigned using the same method. The length of gaps was expressed as a percentage of total length of the margins. Data (internal adaptation) were submitted to ANOVA and Tukey's test. RESULTS: All restorations showed perfect seal of the enamel outer margins. Modulated photoactivation methods (SS, PD, and IL) showed a significant reduction on internal gap formation when compared with CL, regardless of the composite. Filtek Z250 showed the best internal adaptation, regardless of the photoactivation method. CONCLUSION: Modulated photoactivation methods decrease the internal gap formation of composite restorations, and should be encouraged on clinical practice.

A new arginine-based dental adhesive system: formulation, mechanical and anti-caries properties.

Secondary caries at the margins of composite restorations has been attributed to adhesive failure and consequent accumulation of cariogenic biofilms. OBJECTIVES: To develop and evaluate an etch-and-rinse adhesive system containing arginine for sustainable release and recharge without affecting its mechanical properties. Arginine metabolism by oral bacteria generates ammonia, which neutralizes glycolytic acids and creates a neutral environmental pH that is less favorable to the growth of caries pathogens, thus reducing the caries risk at the tooth-composite interface. METHODS: Experimental adhesives were formulated with methacrylate monomers and arginine at 5%, 7%, and 10% or no arginine (control). Adhesives were tested for: (i) mechanical properties of true stress (FS and UTS), modulus of elasticity (E), degree of conversion (DC), Knoop hardness number (KHN) and dentin microtensile bond strength (µ-TBS), (ii) arginine release and recharge, and (iii) antibacterial activities. Data was analyzed by t-test, one-way ANOVA and Tukey's tests. RESULTS: FS and UTS results showed no statistically significant differences between the 7% arginine-adhesive and control, while the results for E, DC, KHN and µ-TBS showed no difference among all groups. The 7% arginine-adhesive showed a high release rate of arginine (75.0µmol/cm2) at 2h, and a more sustainable, controlled release rate (up to 0.2µmol/cm2) at 30days. CONCLUSIONS: Incorporation of 7% arginine did not affect the physical and mechanical properties of the adhesive. Arginine was released from the adhesive at a rate and concentration that exhibited antibacterial effects, regardless of shifts in biofilm conditions such as sugar availability and pH. CLINICAL SIGNIFICANCE: Secondary caries is recognized as the main reason for failure of dental restorations. The development of an arginine-based adhesive system has the potential to dramatically reduce the incidence and severity of secondary caries in adhesive restorations in a very economical fashion.

Influence of alginate impression materials and storage time on surface detail reproduction and dimensional accuracy of stone models.

This study compared the surface detail reproduction and dimensional accuracy of stone models obtained from molds prepared using different alginate impression materials (Cavex ColorChange, Hydrogum 5, or Jeltrate Plus) and with different storage times (1, 3, and 5 days) to models from molds that were filled immediately with no storage time. The molds were prepared over a matrix containing 50-µm line, (ISO 1563 standard) under pressure with a perforated metal tray. The molds were removed 2 minutes after loss of sticky consistency and either filled immediately or stored in closed jars at 100% relative humidity and 37°C for 1, 3, or 5 days. The molds were filled with dental plaster (Durone IV). Surface detail reproduction and dimensional accuracy were evaluated using optical microscopy on the 50-µm wide line, which was 25 mm in length, according to ISO 1563 standard. The dimensional accuracy results (%) were subjected to analysis of variance. The 50-µm wide line (ISO 1563 standard) was completely reproduced by all alginate impression materials regardless of the storage time. There was no statistically significant difference in the mean dimensional accuracy values of stone models made from molds composed of different alginate impression materials and with different storage times (p = 0.989). In conclusion, storing the mold for five days prior to filling did not change the surface detail reproduction or dimensional accuracy of the alginates examined in this study.

Surface detail reproduction and dimensional accuracy of molds: influence of disinfectant solutions and elastomeric impression materials / Reprodução de detalhes da superfície e estabilidadedimensional de moldes: influência das soluçõesdesinfetantes e elastômeros

This study compared the surface detail reproduction anddimensional accuracy of molds after disinfection using 2% sodium hypochlorite, 2% chlorhexidine digluconate or 0.2% peracetic acid to those of molds that were not disinfected, forfour elastomeric impression materials: polysulfide (Light Bodied Permlastic), polyether (Impregum Soft), polydimethylsiloxane(Oranwash L) and polyvinylsiloxane (Aquasil Ultra LV). Themolds were prepared on a matrix by applying pressure, using aperforated metal tray. The molds were removed followingpolymerization and either disinfected (by soaking in one of thesolutions for 15 minutes) or not disinfected. The samples werethus divided into 16 groups (n=5). Surface detail reproductionand dimensional accuracy were evaluated using opticalmicroscopy to assess the 20 ­µm line over its entire 25 mm length. The dimensional accuracy results (%) were subjectedto analysis of variance (ANOVA) and the means were comparedby Tukey’s test (α=5%). The 20 ­µm line was completelyreproduced by all elastomeric impression materials, regardlessof disinfection procedure. There was no significant difference between the control group and molds disinfected with peraceticacid for the elastomeric materials Impregum Soft (polyether)and Aquasil Ultra LV (polyvinylsiloxane). The high­leveldisinfectant peracetic acid would be the choice material for disinfection.

Este estudo comparou a reprodução de detalhes da superfície e estabilidade dimensional de moldes obtidos após desinfecção utilizando hipoclorito de sódio 2%, digluconato de clorexidina 2%, ou ácido peracético 0,2% a moldes que não foram desinfetados com quatro elastômeros: polissulfeto (Light Bodied Permlastic), polieter (Impregum Soft), silicona reação porcondensação (Oranwash L) e silicona reação por adição (Aquasil Ultra LV). Os moldes foram preparados sobre matriz conten dolinhas de 20, 50 e 75 µm realizado sob pressão com moldeirade metal perfurada. Os moldes foram removidos após a polimerização e desinfetados (utilizando uma das soluções porimersão, armazenados em frascos fechados durante 15 minutos)ou não desinfetados. Assim, as amostras foram divididas em 16grupos (n=5). A reprodução detalhes da superfície e a precisão dimensional foram avaliadas usando microscopia óptica na linha 20 µm com 25 mm de comprimento, de acordo com a norma ISO 4823. Os resultados de precisão dimensional (%) foram submetidos à análise de variância (A NOVA) e as médias comparadas pelo teste de Tukey com 5% de nível de significância. A linha de 20 µm foi completamente reproduzida por todos os elastômeros, independentemente do processo de desinfecção. Não houve diferença estatisticamente significativa entre o grupo controle e moldes desinfetados com acido peracético para os elastômeros Impregum Soft (polieter) e Aquasil Ultra LV (siliconareação por adição). O desinfetante de alto nível ácido peracético seria o material de escolha para a desinfecção.

Luting glass ceramic restorations using a self-adhesive resin cement under different dentin conditions.

OBJECTIVES: The aim of this study was to investigate the bond strength of ceramic restorations luted using a self-adhesive resin cement (RelyX Unicem, 3M ESPE) under different dentin conditions. MATERIAL AND METHODS: In the experimental groups, ceramic restorations were luted to bovine incisors with RelyX Unicem under the following conditions: [Dry dentin]: surface was dried using air stream for 15 s; [Moist dentin]: excess dentin moisture was removed with absorbent paper; [Bonding agent]: Clearfil SE Bond (Kuraray) self-etching adhesive system was previously applied to dentin. In the Control group, cementation was done using an etch-and-rinse adhesive (Excite DSC) and Variolink II resin cement (Ivoclar Vivadent). Photoactivation of the resin cements was performed with UltraLume LED 5 unit (Ultradent). The restorations (n=5 per group) were sectioned into beams and microtensile testing was carried out. Data were subjected to ANOVA and Tukey's test (p<0.05). Failure modes were classified under Scanning Electron Microscopic (SEM) (x120 magnification). RESULTS: The bond strength was dependent on the moisture status of the dentin. Bond strength in the "dry dentin group" was significantly lower than that of all other groups, which showed similar results. A predominance of mixed failures was detected for the control group, while a predominance of adhesive failures was observed for the "bonding agent" and "dry dentin" groups. The "moist dentin" group presented predominantly cohesive failures within the luting material. The previous application of a self-etching adhesive showed no significant effect. CONCLUSIONS: Only excess dentin moisture should be removed for the cementation of ceramic restorations with self-adhesive resin cements.