Air- and Moisture Robust Surface Modification for Ni-Rich Layered Cathode Materials for Li-Ion Batteries.

The mainstream of high-energy cathode development is focused on increasing the Ni-ratio in layered structured cathode materials. The increment of the Ni portion in the layered cathode material escalates not only the deliverable capacity but also the structural degradation. High-Ni layered cathodes are highly vulnerable to exposure to air that contains CO2 and H2 O, forming problematic residual lithium compounds at the surface. In this work, a novel air- and moisture robust surface modification is reported for LiNi0.8 Co0.1 Mn0.1 O2 (NCM811) via the sol-gel coating method that selectively coats the internal surface area of the polycrystalline morphology secondary particles. Bare-, Li2 SnO3 -coated and LiCoO2 -coated NCM811 are exposed to different ambient environments (air, hot-air, and moisture-air) to systematically investigate the correlation between the internal/external coating morphology and performance degradations. The LiCoO2 -coated NCM811s exhibit high-capacity retention after exposure to all environments, due to the internal surface coating that prevents the penetration of harmful compounds into the polycrystalline NCM811. On the other hand, the Li2 SnO3 -coated NCM811s exposed to the ambient environments show gradual capacity fading, implying the occurrence of internal degradation. This paper highlights the impact of the internal degradation of polycrystalline NCM811 after environmental exposure and the correct coating mechanisms required to successfully prevent it.

Control of Architecture in Rhombic Dodecahedral Pt-Ni Nanoframe Electrocatalysts.

Platinum-based alloys are known to demonstrate advanced properties in electrochemical reactions that are relevant for proton exchange membrane fuel cells and electrolyzers. Further development of Pt alloy electrocatalysts relies on the design of architectures with highly active surfaces and optimized utilization of the expensive element, Pt. Here, we show that the three-dimensional Pt anisotropy of Pt-Ni rhombic dodecahedra can be tuned by controlling the ratio between Pt and Ni precursors such that either a completely hollow nanoframe or a new architecture, the excavated nanoframe, can be obtained. The excavated nanoframe showed ∼10 times higher specific and ∼6 times higher mass activity for the oxygen reduction reaction than Pt/C, and twice the mass activity of the hollow nanoframe. The high activity is attributed to enhanced Ni content in the near-surface region and the extended two-dimensional sheet structure within the nanoframe that minimizes the number of buried Pt sites.

Hollow Silicon Nanostructures via the Kirkendall Effect.

The Kirkendall effect is a simple, novel phenomenon that may be applied for the synthesis of hollow nanostructures with designed pore structures and chemical composition. We demonstrate the use of the Kirkendall effect for silicon (Si) and germanium (Ge) nanowires (NWs) and nanoparticles (NPs) via introduction of nanoscale surface layers of SiO2 and GeO2, respectively. Depending on the reaction time, Si and Ge atoms gradually diffuse outward through the oxide layers, with pore formation in the nanostructural cores. Through the Kirkendall effect, NWs and NPs were transformed into nanotubes (NTs) and hollow NPs, respectively. The mechanism of the Kirkendall effect was studied via quantum molecular dynamics calculations. The hollow products demonstrated better electrochemical performance than their solid counterparts because the pores developed in the nanostructures resulted in lower external pressures during lithiation.

Germanium Silicon Alloy Anode Material Capable of Tunable Overpotential by Nanoscale Si Segregation.

We developed the novel electrode that enables fine control of overpotential by exploiting surface segregation that is the enrichment of one component at the surface of binary alloy. To realize this approach, we controlled the proportion of Si with low Li diffusivity at the surface by annealing the SiGe nanowire in H2 environment at various temperatures. The resulting SiGe nanowires annealed at 850 °C exhibited high reversible capacity (>1031 mA·h·g(-1)), and long cycle life (400 cycles) with high capacity retention (89.0%) at 0.2 C. This superior battery performance is attributed to the remaining unlithiated part acting as support frame to prevent pulverization of anode material, which results from the fine-tuning of overpotential by controlling the degree of Si segregation.

Quantum confinement and its related effects on the critical size of GeO2 nanoparticles anodes for lithium batteries.

This work has been performed to determine the critical size of the GeO2 nanoparticle for lithium battery anode applications and identify its quantum confinement and its related effects on the electrochemical performance. GeO2 nanoparticles with different sizes of ∼ 2, ∼ 6, ∼ 10, and ∼ 35 nm were prepared by adjusting the reaction rate, controlling the reaction temperature and reactant concentration, and using different solvents. Among the different sizes of the GeO2 nanoparticles, the ∼ 6 nm sized GeO2 showed the best electrochemical performance. Unexpectedly smaller particles of the ∼ 2 nm sized GeO2 showed the inferior electrochemical performances compared to those of the ∼ 6 nm sized one. This was due to the low electrical conductivity of the ∼ 2 nm sized GeO2 caused by its quantum confinement effect, which is also related to the increase in the charge transfer resistance. Those characteristics of the smaller nanoparticles led to poor electrochemical performances, and their relationships were discussed.

Catalyst-free direct growth of a single to a few layers of graphene on a germanium nanowire for the anode material of a lithium battery.

Direct growth of a single to a few layers of graphene on a germanium nanowire (Gr/Ge NW; see picture) was achieved by a metal-catalyst-free chemical vapor deposition (CVD) process. The Gr/Ge NW was used as anode in a lithium ion battery. This material has a specific capacity of 1059 mA h g(-1) at 4.0 C, a long cycle life over 200 cycles, and a high capacity retention of 90%.

Synthesis of Highly Dispersible Functionalized Carbon Nanotubes as Conductive Material through a Facile Drying Process for High-Power Lithium-ion Batteries.

Herein, surface-functionalized carbon nanotubes (CNTs) were successfully synthesized by dry ball milling that facilitates industrial application. The optimal conditions were determined by analyzing the physicochemical characteristics of CNTs, including the content of the carboxyl group (-COOH) induced on the surface of CNTs by co-existing dry ice based on the ball milling time. Among them, 30 s ball milling (CNTs-30s) showed a high dispersibility in N-methyl-2-pyrrolidone (NMP) while retaining most carboxyl groups and maintaining the intrinsic high conductivity. In the evaluation of rate capability and 5 C/5 C cyclability applied to the Li1+x (Ni1-y-z Coy Mnz )1-x O2 with 60 % Ni (NCM622) cathode, CNTs-30s showed excellent performance based on a well-formed conductive network. Regarding improved dispersion properties and electrochemical performance, the optimal surface functionalization conditions, dispersibility, and electrode properties according to the processing time were analyzed; based on these, the correlation with electrochemical performance was confirmed.

Micron-Sized SiOx-Graphite Compound as Anode Materials for Commercializable Lithium-Ion Batteries.

The electrode concept of graphite and silicon blending has recently been utilized as the anode in the current lithium-ion batteries (LIBs) industry, accompanying trials of improvement of cycling life in the commercial levels of electrode conditions, such as the areal capacity of approximately 3.3 mAh/cm2 and volumetric capacity of approximately 570 mAh/cm3. However, the blending concept has not been widely explored in the academic reports, which focused mainly on how much volume expansion of electrodes could be mitigated. Moreover, the limitations of the blending electrodes have not been studied in detail. Therefore, herein we investigate the graphite blending electrode with micron-sized SiOx anode material which is one of the most broadly used Si anode materials in the industry, to approach the commercial and practical view. Compared to the silicon micron particle blending electrode, the SiOx blending electrode showed superior cycling performance in the full cell test. To elucidate the cause of the relatively less degradation of the SiOx blending electrode as the cycling progressed in full-cell, the electrode level expansion and the solid electrolyte interphase (SEI) thickening were analyzed with various techniques, such as SEM, TEM, XPS, and STEM-EDS. We believe that this work will reveal the electrochemical insight of practical SiOx-graphite electrodes and offer the key factors to reducing the gap between industry and academic demands for the next anode materials.

Analysis of Electrochemical Performance with Dispersion Degree of CNTs in Electrode According to Ultrasonication Process and Slurry Viscosity for Lithium-Ion Battery.

Lithium-ion batteries (LIBs) continue to dominate the battery market with their efficient energy storage abilities and their ongoing development. However, at high charge/discharge C-rates their electrochemical performance decreases significantly. To improve the power density properties of LIBs, it is important to form a uniform electron transfer network in the cathode electrode via the addition of conductive additives. Carbon nanotubes (CNTs) with high crystallinity, high electrical conductivity, and high aspect ratio properties have gathered significant interest as cathode electrode conductive additives. However, due to the high aggregational properties of CNTs, it is difficult to form a uniform network for electron transfer within the electrode. In this study, to help fabricate electrodes with well-dispersed CNTs, various electrodes were prepared by controlling (i) the mixing order of the conductive material, binder, and active material, and (ii) the sonication process of the CNTs/NMP solution before the electrode slurry preparation. When the binder was mixed with a well sonicated CNTs/NMP solution, the CNTs uniformly adsorbed to the then added cathode material of LiNi0.6Co0.2Mn0.2O2 and were well-dispersed to form a flowing uniform network. This electrode fabrication process achieved > 98.74% capacity retention after 50 cycles at 5C via suppressed polarization at high current densities and a more reversible H1-M phase transition of the active material. Our study presents a novel design benchmark for the fabricating of electrodes applying well-dispersed CNTs, which can facilitate the application of LIBs in high current density applications.

Towards maximized volumetric capacity via pore-coordinated design for large-volume-change lithium-ion battery anodes.

To achieve the urgent requirement for high volumetric energy density in lithium-ion batteries, alloy-based anodes have been spotlighted as next-generation alternatives. Nonetheless, for the veritable accomplishment with regards to high-energy demand, alloy-based anodes must be evaluated considering several crucial factors that determine volumetric capacity. In particular, the electrode swelling upon cycling must be contemplated if these anodes are to replace conventional graphite anodes in terms of volumetric capacity. Herein, we propose macropore-coordinated graphite-silicon composite by incorporating simulation and mathematical calculation of numerical values from experimental data. This unique structure exhibits minimized electrode swelling comparable to conventional graphite under industrial electrode fabrication conditions. Consequently, this hybrid anode, even with high specific capacity (527 mAh g-1) and initial coulombic efficiency (93%) in half-cell, achieves higher volumetric capacity (493.9 mAh cm-3) and energy density (1825.7 Wh L-1) than conventional graphite (361.4 mAh cm-3 and 1376.3 Wh L-1) after 100 cycles in the full-cell configuration.

Exploring Critical Factors Affecting Strain Distribution in 1D Silicon-Based Nanostructures for Lithium-Ion Battery Anodes.

Despite the advantage of high capacity, the practical use of the silicon anode is still hindered by large volume expansion during the severe pulverization lithiation process, which results in electrical contact loss and rapid capacity fading. Here, a combined electrochemical and computational study on the factor for accommodating volume expansion of silicon-based anodes is shown. 1D silicon-based nanostructures with different internal spaces to explore the effect of spatial ratio of voids and their distribution degree inside the fibers on structural stability are designed. Notably, lotus-root-type silicon nanowires with locally distributed void spaces can improve capacity retention and structural integrity with minimum silicon pulverization during lithium insertion and extraction. The findings of this study indicate that the distribution of buffer spaces, electrochemical surface area, as well as Li diffusion property significantly influence cycle performance and rate capability of the battery, which can be extended to other silicon-based anodes to overcome large volume expansion.

Highly Active Bifunctional Electrocatalysts for Oxygen Evolution and Reduction in Zn-Air Batteries.

To realize the full performance of Zn-air batteries, the co-presence of a highly efficient oxygen reduction reaction (ORR) and an oxygen evolution reaction (OER) in the system is critical. Although copper and nickel are known to be bifunctional catalysts for ORR and OER, sluggish reactions as a result of the exceptionally strong O=O bond on the metal surface make it difficult to achieve high system efficiency. In this study, a metal carbide layer (CuCx and NiCx ) on dendritic copper and nickel is fabricated by a facile electrodeposition process to provide efficient catalytic active sites with moderate binding energy for easy electron transfer in both the OER and the ORR. The dendritic structure provides an enriched catalytic surface and the protective metal carbide layer offers an appropriate O binding energy and durability of Zn-air batteries. Owing to the presence of the stable metal carbide surface on the dendritic metal, the CuCx /Cu and NiCx /Ni catalysts exhibited well-defined limiting current densities of -5.19 and -5.11 mA cm-2 , respectively, and improved ORR and OER activities with lower polarization than the corresponding metal catalysts. Density functional theory revealed a 0.74 eV decrease in the overpotential of NiCx /Ni-catalyzed OER reactions compared with Ni-catalyzed OER reactions. The experimental and theoretical results prove that carbide layers on dendritic metal surfaces can greatly improve the activity of ORR and OER bifunctional electrocatalysts for Zn-air batteries.