RESUMO
Perovskite light-emitting diodes have recently broken the 20% barrier for external quantum efficiency. These values cannot be explained with classical models for optical outcoupling. Here, we analyse the role of photon recycling (PR) in assisting light extraction from perovskite light-emitting diodes. Spatially-resolved photoluminescence and electroluminescence measurements combined with optical modelling show that repetitive re-absorption and re-emission of photons trapped in substrate and waveguide modes significantly enhance light extraction when the radiation efficiency is sufficiently high. In this manner, PR can contribute more than 70% to the overall emission, in agreement with recently-reported high efficiencies. While an outcoupling efficiency of 100% is theoretically possible with PR, parasitic absorption losses due to absorption from the electrodes are shown to limit practical efficiencies in current device architectures. To overcome the present limits, we propose a future configuration with a reduced injection electrode area to drive the efficiency toward 100%.
RESUMO
The influence of three different solvents and a solvent additive on the morphology and photovoltaic performance of bulk heterojunction films made of the copolymer based on thieno[3,4-b]thiophene-alt-benzodithiophene unit PTB7-F40 blended with [6,6]-phenyl-C71-butyric acid methyl ester (PC71BM) is investigated. Optical microscopy and atomic force microscopy are combined with X-ray reflectivity and grazing incidence small and wide-angle X-ray scattering (GISAXS and GIWAXS, respectively), enabling the characterization of the morphology of the whole photoactive film. The detailed study reveals that different length scales of PCBM clusters are observed using different solvents, while adding a solvent additive results in the PCBM clusters being selectively dissolved. Vertical and lateral phase separation occurs during spin coating and depends on the solvent used. A hierarchical morphology is detected within the bulk film through GISAXS measurements. Furthermore, GIWAXS shows that a rather amorphous film with low crystallinity was probed, which substantiates that high crystallinity is not necessarily required for high performance organic solar cells. Different models for the morphology are proposed through the combination of all the findings and correlated with the corresponding device properties. Consequently, the solvent-induced different device performance is mainly ascribed to the varied lateral structure sizes, whereas the highest device performance is a result of the smallest average multilength scale lateral structure sizes with the smallest length scale matching the exciton diffusion length.
RESUMO
We report on individual-InAs nanowire optoelectronic devices which can be tailored to exhibit either negative or positive photoconductivity (NPC or PPC). The NPC photoresponse time and magnitude is found to be highly tunable by varying the nanowire diameter under controlled growth conditions. Using hysteresis characterization, we decouple the observed photoexcitation-induced hot electron trapping from conventional electric field-induced trapping to gain a fundamental insight into the interface trap states responsible for NPC. Furthermore, we demonstrate surface passivation without chemical etching which both enhances the field-effect mobility of the nanowires by approximately an order of magnitude and effectively eliminates the hot carrier trapping found to be responsible for NPC, thus restoring an "intrinsic" positive photoresponse. This opens pathways toward engineering semiconductor nanowires for novel optical-memory and photodetector applications.
RESUMO
Films of the semiconducting polymer poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b']dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] with 40% fluorinated monomers, denoted PTB7-F40, are spin coated out of different solvents onto PEDOT:PSS films. The influence of the used solvents chlorobenzene, 1,2-dichlorobenzene, and 1,2,4-trichlorobenzene as well as the influence of the additive 1,8-diiodooctane (DIO) is probed with grazing incidence small- and wide-angle X-ray scattering (GISAXS and GIWAXS). As seen with GISAXS, without DIO, the films are homogeneous and show roughness correlation with the PEDOT:PSS film surface. With DIO, an inner film structure with a size of 50-75 nm is found and the roughness correlations weaken. In addition, as seen in GIWAXS, the crystalline part of the films is influenced by the used solvent if DIO is added.