Synthesis of Fe2SiO4-Fe7Co3 Nanocomposite Dispersed in the Mesoporous SBA-15: Application as Magnetically Separable Adsorbent.

The mixture containing alloy and oxide with iron-based phases has shown interesting properties compared to the isolated species and the synergy between the phases has shown positive effect on dye adsorption. This paper describes the synthesis of Fe2SiO4-Fe7Co3-based nanocomposite dispersed in Santa Barbara Amorphous (SBA)-15 and its application in dye adsorption followed by magnetic separation. Thus, it was studied the variation of reduction temperature and amount of hydrogen used in synthesis and the effect of these parameters on the physicochemical properties of the iron and cobalt based oxide/alloy mixture, as well as the methylene blue adsorption capacity. The XRD and Mössbauer results, along with the temperature-programmed reduction (TPR) profiles, confirmed the formation of Fe2SiO4-Fe7Co3-based nanocomposites. Low-angle XRD, N2 isotherms, and TEM images show the formation of the SBA-15 based mesoporous support with a high surface area (640 m2/g). Adsorption tests confirmed that the material reduced at 700 °C using 2% of H2 presented the highest adsorption capacity (49 mg/g). The nanocomposites can be easily separated from the dispersion by applying an external magnetic field. The interaction between the dye and the nanocomposite occurs mainly by π-π interactions and the mixture of the Fe2SiO4 and Fe7Co3 leads to a synergistic effect, which favor the adsorption.

Incorporation of Brazilian Diatomite in the Synthesis of An MFI Zeolite.

The need for greener procedures is a fact to reduce residues, to decrease industrial costs, and to accomplish the environmental agreements. In an attempt to address this question, we propose the addition of a natural resource, Brazilian diatomite, to an MFI zeolite traditional synthesis. We have characterized the resulting product with different techniques, such as X-ray diffraction, microscopy, and gas sorption, and, afterwards, we evaluate the greenness of the process by the Green Star method. The results were promising: We obtained the desired topology in the form of small crystallites aggregated and a pore diameter of 0.8 nm. In conclusion, the product has the necessary characteristics for an adsorption or catalytic future tests and escalation to industrial production.

Al/SBA-15 Mesoporous Material: A Study of pH Influence over Aluminum Insertion into the Framework.

Herein, ordered mesoporous materials like SBA-15 and Al/SBA-15 were prepared using the pH adjustment method. Thus, these materials were developed in different pH of synthesis, from the pH adjustment method using a KCl/HCl solution and varying the Si/Al molar ratio (5, 25, and 75). All the ordered mesoporous materials were characterized by FRX, 27Al NMR, SEM, XRD, N2 adsorption/desorption, and CO2 adsorption. From the applied method, it was possible to obtain SBA-15 and Al/SBA-15 with high mesoscopic ordering based on the XRD patterns, independent of the pH employed. From the chemical composition, the insertion of higher amounts of Al into the synthesis caused a progressive improvement in the structural and textural properties of the ordered mesoporous materials. Thus, the chosen synthesis conditions can lead to different aluminum coordination (tetrahedral and octahedral), which gives these materials a greater potential to be applied. The presence of Al in high amounts provides material with the ability to form micropores. Finally, the proposed method proved to be innovative; low-cost; less aggressive to the environment, with efficient insertion of aluminum in the framework of SBA-15 mesoporous material; and practical, based on only one step.

Unraveling the influence of surface functionalities on gas Physisorption: A comprehensive study on SBA-15 nanoporous material from Monte Carlo simulation for improved Textural-Energetic characterization.

In this study, we conducted experimental and Monte Carlo simulation studies in the grand canonical ensemble (GCMC) to investigate the role of molecular orientation and surface heterogeneity on the adsorption of N2 at 77 K. Our research focused on a series of ordered nanoporous materials (SBA-15) with varying degrees of oxygen functionalities. Specifically, we examined the effects of surface heterogeneity on the calculation of pore size distribution (PSD) and the Brunauer-Emmett-Teller (BET) area of porous materials. To provide a comprehensive perspective, we compared our results with three levels of surface oxidation, including a pristine case without any surface oxidation. The results from both our experimental and simulation data reveal the importance of chemical heterogeneity in determining equilibrium properties such as molecular packing within the pores, differential enthalpies of adsorption, and N2 orientation distribution. Our findings suggest that accurate characterization of surface heterogeneity is crucial for understanding gas adsorption in nanoporous materials and for developing better models for predicting their performance in various applications. Moreover, our simulations revealed substantial changes in the molecular orientation of adsorbate particles with increasing surface heterogeneity. This insight provides valuable information about the behavior of molecules within the nanoporous materials, further enhancing our understanding of the complex adsorption processes in these systems.

Influence of Pressure and Temperature on the Flexible Behavior of Iron-Based MIL-53 with the CO2 Host: A Comprehensive Experimental and DFT Study.

This research focuses on developing MIL-53-type compounds with Fe obtained with ligands derived from PET waste, followed by the controlled addition of hydrofluoric acid (HF). Incorporating HF into the MOF structure induced substantial changes in the material textural properties, resulting in a significant change in CO2 adsorption. Furthermore, a distinctive structural alteration (breathing effect) was observed in the CO2 isotherms at different temperatures; these structural changes have not been observed by X-ray diffraction (XRD) because this characterization has been performed at room temperature, whereas the adsorption experiments were conducted at 260, 273, and 303 K and different pressures. Subsequently, DFT studies were performed to investigate the CO2-filling mechanisms and elucidate the material respiration effect. This approach offers promising opportunities for sustainable materials with improved gas adsorption properties.

Development of ceramic honeycomb monolith from natural zeolite tested as adsorbent to remove methylene blue in aqueous media.

This work presents a ceramic monolith with a honeycomb structure obtained from a natural zeolite (clinoptilolite), bentonite, and alumina. The monolith obtained by extrusion had a cell density of 57 CPSI (cells per square inch), an open frontal area of 52% w/w, and a wall thickness of 0.9 mm. The raw materials and the natural zeolite ceramic monolith (NZCM) were characterized by X-ray diffraction, N2 adsorption-desorption at 77 K, CO2 adsorption at 273 K, mercury intrusion-extrusion, axial compression tests, resistance to leaching at acidic and basic pH, and point of zero charge. The NZCM presented an SBET = 31 m2∙g-1, a modal micropore size of 0.44 nm, a porosity of 39%, the compressive stress = 14 MPa, and a pHPZC = 7.5. The NZCM was used as an inexpensive and easy-to-handle adsorbent to remove methylene blue (MB) dye in batch studies of kinetics and adsorption isotherms. From modeling of adsorption kinetic data, the predominant phenomenon in this system was physisorption. The modeling of adsorption isotherm data shows that the material has homogeneous active sites. The adsorption occurs by monolayer formation, finding a maximum capacity removal rate of 27 mg MB per gram of NZCM. Compared to other structured materials, a high capacity for removing MB with the ceramic monolith was obtained along with good mechanical properties and resistance in acidic and alkaline environments.

Organic-Free Synthesis of Finned Mordenite Zeolite.

Mordenite is a well-known zeolite widely used for industrial processes. However, its pore architecture can be inconvenient due to diffusional issues. A study of the synthesis parameters from an organic-free dense gel was carried out to control the crystal morphology, which resulted in finned mordenite zeolite particles. The obtained materials were characterized by XRD, FTIR, 29Si and 27Al MAS-NMR, elemental analysis, nitrogen physisorption, SEM, and TEM. We found that careful manipulation of the hydrothermal parameters directly affected the sizes and morphologies of the crystallites and particles, as well as the textural properties of the final products. Additionally, it was found that mordenite could exhibit a fin morphology with additional mesoporosity, which is a promising means to reduce the diffusional problems of one-dimensional-channel zeolites.

Dandelion-Like Microspherical MCM-22 Zeolite Using BP 2000 as a Hard Template.

The chemistry between layered MWW zeolite and carbon black pearls (BP 2000) as an inexpensive hard template was investigated to develop a rational one-pot synthesis of MCM-22 microspheres. The characterization results showed that the insertion of BP 2000 in the gel synthesis did not substantially compromise the crystallinity and microporosity, and the microscopic analyses showed that BP 2000 played a key role in controlling the final morphology of the MCM-22 zeolite, creating beautiful dandelion-like microspherical particles. The morphology obtained is due to the tortuous shape of the hard template, the particular MWW particle crystals, the interaction with the external surface of the MWW zeolitic precursor, and the synthesis conditions. The stacking of MWW crystals with edge-to-face orientations generates meso-/macrovoids, allowing access to the interiors of the microspheres. The microspheres were homogeneous with sizes ranging from 6 to 8 µm with an increase of the external surface and a macroporous size distribution centered at 200 nm, which is two times that of the traditional MCM-22 zeolite.

Microfluidic immunosensor based on mesoporous silica platform and CMK-3/poly-acrylamide-co-methacrylate of dihydrolipoic acid modified gold electrode for cancer biomarker detection.

We report a hybrid glass-poly (dimethylsiloxane) microfluidic immunosensor for epidermal growth factor receptor (EGFR) determination, based on the covalent immobilization of anti-EGFR antibody (anti-EGFR) on amino-functionalized mesoporous silica (AMS) retained in the central channel of a microfluidic device. The synthetized AMS was characterized by N2 adsorption-desorption isotherm, scanning electron microscopy (SEM), energy dispersive spectrometry (EDS) and infrared spectroscopy. The cancer biomarker was quantified in human serum samples by a direct sandwich immunoassay measuring through a horseradish peroxidase-conjugated anti-EGFR. The enzymatic product was detected at -100 mV by amperometry on a sputtering gold electrode, modified with an ordered mesoporous carbon (CMK-3) in a matrix of poly-acrylamide-co-methacrylate of dihydrolipoic acid (poly(AC-co-MDHLA)) through in situ copolymerization. CMK-3/poly(AC-co-MDHLA)/gold was characterized by cyclic voltammetry, EDS and SEM. The measured current was directly proportional to the level of EGFR in human serum samples. The linear range was from 0.01 ng mL-1 to 50 ng mL-1. The detection limit was 3.03 pg mL-1, and the within- and between-assay coefficients of variation were below 5.20%. The microfluidic immunosensor is a very promising device for the diagnosis of several kinds of epithelial origin carcinomas.

Development of a nanostructured immunosensor for early and in situ detection of Xanthomonas arboricola in agricultural food production.

We report a microfluidic electrochemical immunosensor for Xanthomonas arboricola (XA) determination, based on the covalently immobilization of monoclonal anti-XA antibody (anti-XA) on a previously amino functionalized SBA-15 in situ synthesized in the central channel of a glass-poly(dimethylsiloxane) microfluidic immunosensor. The synthetized amino-SBA-15 was characterized by N2 adsorption-desorption isotherm, scanning electron microscopy and infrared spectroscopy. XA was detected by a direct sandwich immunoassay through an alkaline phosphatase (AP) enzyme-labeled anti-XA conjugate. Later, the substrate p-aminophenyl phosphate was converted to p-aminophenol by AP. The enzymatic product was detected at +100mV on a sputtered gold electrode. The measured current was directly proportional to the level of XA in walnut trees samples. The linear range was from 5 × 102 to 1 × 104CFUmL-1. The detection limit was 1.5 × 102CFUmL-1, and the within- and between-assay coefficients of variation were below 5%. Microfluidic immunosensor is a very promising tool for the early and in situ diagnosis of XA in walnuts avoiding serious economic losses.