Correction: A generalized method for alignment of block copolymer films: solvent vapor annealing with soft shear.

Correction for 'A generalized method for alignment of block copolymer films: solvent vapor annealing with soft shear' by Zhe Qiang et al., Soft Matter, 2014, 10, 6068-6076, https://doi.org/10.1039/C4SM00875H.

Sodium dodecyl sulfate modulates the structure and rheological properties of Pluronic F108-poly(acrylic acid) coacervates).

Micelles formed within coacervate phases can impart functional properties, but it is unclear if this micellization provides mechanical reinforcement of the coacervate whereby the micelles act as high functionality crosslinkers. Here, we examine how sodium dodecyl sulfate (SDS) influences the structure and properties of Pluronic F108-polyacrylic acid (PAA) coacervates as SDS is known to decrease the aggregation number of Pluronic micelles. Increasing the SDS concentration leads to larger water content in the coacervate and an increase in the relative concentration of PAA to the other solids. Rheological characterization with small angle oscillatory shear (SAOS) demonstrates that these coacervates are viscoelastic liquids with the moduli decreasing with the addition of the SDS. The loss factor (tan δ) initially increases linearly with the addition of SDS, but a step function increase in the loss factor occurs near the reported CMC of SDS. However, this change in rheological properties does not appear to be correlated with any large scale structural differences in the coacervate as determined by small angle X-ray scattering (SAXS) with no signature of Pluronic micelles in the coacervate when SDS concentration is >4 mM during formation of the coacervate, which is less than that observed (6 mM SDS) in initial Pluronic F108 solution despite the higher polymer concentration in the coacervate. These results suggest that the mechanical properties of polyelectrolyte-non-ionic surfactant coacervates are driven by the efficicacy of binding between the complexing species driving the coacervate, which can be disrupted by competitive binding of the SDS to the Pluronic.

Microwave-Enabled Size Control of Iron Oxide Nanoparticles on Reduced Graphene Oxide.

Nanoparticle-functionalized 2D material networks are promising for a wide range of applications, but in situ formation of nanoparticles is commonly challenged by rapid growth. Here, we demonstrate controlled synthesis of small and dispersed iron oxide nanoparticles on reduced graphene oxide (rGO) networks through rapid localized heating with microwaves with low-cost iron nitrate as the precursor. The strong coupling of the microwave radiation with the rGO network rapidly heats the network locally to decompose the iron nitrate and generate iron oxide nanoparticles, while cessation of microwaves leads to rapid cooling to minimize crystal growth. Small changes in the microwave reaction time (<1 min) led to very large changes in the iron oxide morphology. The solid-state microwave syntheses produced narrower nanoparticle size distribution than conventional heating. These results illustrate the potential of solid-state microwave syntheses to control the nanoparticle size on 2D materials through rapid localized heating under the microwave process conditions, which should be extendable to a variety of transition metal oxide-rGO systems.

Controlling nanostructure and mechanical properties in triblock copolymer/monomer blends via reaction-induced phase transitions.

Thermoplastic elastomers based on ABA triblock copolymers are typically limited in modulus and strength due to crack propagation within the brittle regions when the hard end-block composition favors morphologies that exhibit connected domains. Increasing the threshold end-block composition to achieve enhanced mechanical performance is possible by increasing the number of junctions or bridging points per chain, but these copolymer characteristics also tend to increase the complexity of the synthesis. Here, we report an in situ polymerization method to successfully increase the number of effective junctions per chain through grafting of poly(styrene) (PS) to a commercial thermoplastic elastomer, poly(styrene)-poly(butadiene)-poly(styrene) (SBS). The strategy described here transforms a linear SBS triblock copolymer-styrene mixture into a linear-comb-linear architecture in which poly(styrene) (PS) grafts from the mid-poly(butadiene) (PBD) block during the polymerization of styrene. Through systematic variation in the initial SBS/styrene content, nanostructural transitions from disordered spheres to lamellar through reaction-induced phase transitions (RIPT) were identified as the styrene content increased. Surprisingly, maximum mechanical performance (Young's modulus, tensile strength, and elongation at break) was obtained with samples exhibiting lamellar nanostructures, corresponding to overall PS contents of 61-77 wt% PS (including the original PS in SBS). The PS grafting from the PBD block increases the modulus and the strength of the thermoplastic elastomer while preventing brittle fracture due to the greater number of junctions afforded by the PS grafts. The work presented here demonstrates the use of RIPT to transform standard SBS materials into polymer systems with enhanced mechanical properties.

Non-destructive determination of functionalized polyelectrolyte placement in layer-by-layer films by IR ellipsometry.

Layer-by-layer (LbL) assembly facilitates controlled coatings on a variety of surfaces with the ability to manipulate the composition through the thickness by selection of the complementary pairs. However, the characterization of these composition profiles tends to be destructive and requires significant compositional differences that can limit their utility. Here, we demonstrate the ability to non-destructively quantify the depth dependence of the allyl content associated with the selective incorporation of poly(sodium acrylate-co-allylacrylamide) (84 : 16 mol : mol) (allyl-PAA) in LbL films based on the assembly of poly(diallyldimethylammonium chloride) (PDAC)/poly(acrylic acid) (PAA) and PDAC/allyl-PAA. Although the atomic composition of the film is not dramatically influenced by the change between PAA and allyl-PAA, the absorption in the IR near 1645 cm-1 by the allyl group provides sufficient optical contrast to distinguish the LbL components with spectroscopic ellipsometry. The use of IR spectroscopic ellipsometry can determine the thickness of layers that contain allyl-PAA and also gradients that develop due to re-arrangements during the LbL process. With multiple films fabricated simultaneously, the location of the gradient between the 1st and 2nd series of multilayers (e.g., first PDAC/PAA bilayers and then PDAC/allyl-PAA bilayers) can be readily assessed. The results from a variety of different multilayer architectures indicate that the gradient is located within the thickness expected for the 1st deposited bilayer stack (PDAC/PAA or PDAC/allyl-PAA). These results are indicative of a dynamic dissolution-deposition process (in- and out- diffusion) during the fabrication of these LbL films. These results provide additional evidence into the mechanisms for exponential growth in LbL assemblies. The ability to quantify a gradient with the low contrast system examined indicates that spectroscopic IR ellipsometry should be able to non-destructively determine compositional gradients for most polymer films where such gradients exist.

Water dynamics within nanostructured amphiphilic statistical copolymers from quasielastic neutron scattering.

Understanding the properties of water under either soft or hard confinement has been an area of great interest, but nanostructured amphiphilic polymers that provide a secondary confinement have garnered significantly less attention. Here, a series of statistical copolymers of 2-hydroxyethyl acrylate (HEA) and 2-(N-ethylperfluorooctane sulfonamido)ethyl methacrylate (FOSM) are swollen to equilibrium in water to form nanostructured physically cross-linked hydrogels to probe the effect of soft confinement on the dynamics of water. Changing the composition of the copolymer from 10 to 21 mol. % FOSM decreases the average size of the assembled FOSM cross-link, but also the spacing between the cross-links in the hydrogels with the mean distance between the FOSM aggregates decreasing from 3.9 to 2.7 nm. The dynamics of water within the hydrogels were assessed with quasielastic neutron scattering. These hydrogels exhibit superior performance for inhibition of water crystallization on supercooling in comparison to analogous hydrogels with different hydrophilic copolymer chemistries. Despite the lower water crystallinity, the self-diffusion coefficient for these hydrogels from the copolymers of HEA and FOSM decreases precipitously below 260 K, which is a counter to the nearly temperature invariant water dynamics reported previously with an analogous hydrogel [Wiener et al., J. Phys. Chem. B 120, 5543 (2016)] that exhibits nearly temperature invariant dynamics to 220 K. These results point to chemistry dependent dynamics of water that is confined within amphiphilic hydrogels, where the interactions of water with the hydrophilic segments can qualitatively alter the temperature dependent dynamics of water in the supercooled state.

Microwave Processing Controls the Morphology of Block Copolymer-Templated Mesoporous Cobalt Oxide Films.

Microwave heating provides an efficient method to rapidly heat materials through interaction of microwaves with the media. Here, we demonstrate the rapid synthesis of mesoporous cobalt oxide films through the heating of the silicon substrate by microwaves. A non-sol-gel approach based on cobalt nitrate-citric acid complex cooperative assembly with a poly[methoxy poly(ethylene glycol)methacrylate]-block-poly(butyl acrylate) (PMPEGMA-b-PBA) block copolymer was used to fabricate the cobalt oxide through a cobalt carbonate intermediate. The time required to convert cobalt carbonate to cobalt oxide with the full removal of the PMPEGMA-b-PBA template can be decreased by two orders of magnitude with microwaves in comparison to standard heating in a furnace at 350 °C. At the highest microwave power examined (1500 W), this can be accomplished within 2 s, while >5 min is required at 350 °C in a furnace. At a microwave power of <400 W, there is insufficient energy to induce the transition from carbonate to oxide, but even at only 420 W, the oxide can be formed within 26 s. The rapid heating by the microwaves tends to increase the crystallinity and mean crystal size of the cobalt oxide within the mesoporous films. Despite the growth of larger average crystals, the pore size and porosity tend to be larger when the film is processed using microwaves. Higher microwave power leads to larger average crystals and average pore size. These results suggest that rapid processing to crystallize frameworks in mesoporous materials may allow for highly crystalline frameworks without loss of the templated mesostructure.

Aqueous polypropylene glycol induces swelling and severe plasticization of high Tg amphiphilic copolymers containing hexafluoroisopropanol groups.

Poly(ethylene glycol) (PEG) tends to be considered low fouling, which has led to its use in a wide variety of applications. Amphiphilic polyols, such as Antifoam 204, are commonly used as surfactants in fermentation processes due to their limited toxicity and low cost, but these polyols in aqueous solutions can unexpectedly swell membranes. Here we examine the interactions of PEG or poly(propylene glycol) (PPG) with amphiphilic substituted norbornene copolymers through swelling in dilute aqueous solution. The effect of molecular mass (Mn) of the polyol (PEG and PPG) in aqueous (1 wt% butanol) solution on the swelling and mechanical properties of a series of poly(alkyl norbornene-co-hexafluoroisopropanol norbornene) is systematically investigated using a quartz crystal microbalance with dissipation. At 10 ppm of PEG, the swelling is less than 20% for all of the copolymers examined and the swelling is independent of PEG Mn. Although PPG at the lowest Mn examined leads to similar swelling to PEG, the swelling induced by PPG increases with Mn to reach a maximum at Mn = 3.1 kg mol-1. Pluronic L121 is similar compositionally to Antifoam 204, but the equilibrium swelling is decreased by nearly a factor of 2, which is attributed to the higher Mn of Pluronic L121. The limited dependence on the alkyl chain in the copolymer suggest that the interactions between the polyol and hexafluoroisopropanol moiety in the copolymer drive the uptake by the membrane through bound water with the unassociated ether in the PPG that increases swelling with increasing Mn, but a finite size effect limits the swelling for sufficiently large polymer additives.

Tuning Cooperative Assembly with Bottlebrush Block Co-polymers for Porous Metal Oxide Films Using Solvent Mixtures.

Block copolymer templating enables the generation of well-defined pore sizes and geometries in a wide variety of frameworks, typically through evaporation-induced self-assembly (EISA). Here, we systematically modulate the solvent quality with mixtures of tetrahydrofuran-ethanol (THF-EtOH) to manipulate the unimer/micelle ratio in the precursor solution to explore how the associated solution structure influences the final pore morphology. A bottlebrush block copolymer (BBCP) with poly(ethylene oxide) and poly(t-butyl acrylate) side chains was used as the template for pore formation. Irrespective of the solvent composition, a bimodal pore size distribution was obtained with mesopores templated by small aggregates of the BBCP unimers (potentially low aggregation number micelles) and macropores templated by large self-assembled BBCP micelles. The morphology and pore characteristics of the metal oxide films were dependent on the THF-EtOH composition. Interestingly, an intermediate solvent composition where the volume of micelles is approximately half the volume of unimers (in the precursor solution) leads to the best ordering of micelle-templated pores and also the maximum porosity in the films. The micelle/unimer ratios in the precursor solutions do not correspond directly to the bimodal pore distribution in the metal oxide films, which we attribute to kinetically trapped assembly of the BBCP at a low THF content. The increased critical micelle concentration at high THF composition leads to changes in the unimer/micelle ratio during solvent evaporation. These results appear to be universal for a number of metal oxides (cobalt, magnesium, and zinc) with the porosity maximized at a THF/EtOH ratio of 3:1. These results suggest the potential for enhancements in the porosity of block copolymer-templated films by EISA methods through judicious solvent selection.

Influence of Sodium Salts on the Swelling and Rheology of Hydrophobically Cross-linked Hydrogels Determined by QCM-D.

Hydrophobically modified copolymers provide a versatile platform of hydrogel materials for diverse applications, but the influence of salts on the swelling and material properties of this class of hydrogels has not been extensively studied. Here, we investigate model hydrogels with three different sodium salts with anions chosen from the classic Hofmeister series to determine how these counterions influence the swelling and mechanical properties of neutral hydrogels. The gel chosen was based on a statistical copolymer of dimethylacrylamide and 2-(N-ethylperfluorooctane sulfonamido) ethyl acrylate (FOSA). Our measurements utilize a quartz crystal microbalance with dissipation (QCM-D) to quantify both swelling and rheological properties of these gels. We find that a 1 mol/L solution of Na2SO4, corresponding to a kosmotropic anion, leads to nearly a 2.6-fold gel deswelling and correspondingly, the complex modulus increases by an order of magnitude under these solution conditions. In contrast, an initial increase in swelling and then a swelling maximum is observed for a 0.02 mol/L concentration in the case of a chaotropic anion, NaClO4, but the changes in the degree of gel swelling in this system are not directly correlated with changes in the gel shear modulus. The addition of NaBr, an anion salt closer to the middle of the chaotropic to kosmotropic range, leads to hydrogel deswelling where the degree of deswelling and the shear modulus are both nearly independent of salt concentration. Overall, the observed trends are broadly consistent with more kosmotropic ions causing diminished solubility ("salting out") and strongly chaotropic ions causing improved solubility ("salting in"), a trend characteristic of the Hoffmeister series governing the solubility of many proteins and synthetic water-soluble polymers, but trends in the shear stiffness with gel swelling are clearly different from those normally observed in chemically cross-linked gels and are correspondingly difficult to interpret. The salt specificity of swelling and mechanical properties of nonionic hydrogels is important for any potential application in which a wide range of salt concentrations and types are encountered.

Control of Pore Size in Ordered Mesoporous Carbon-Silica by Hansen Solubility Parameters of Swelling Agent.

The cooperative assembly of functional precursors with block copolymers (BCPs) is a powerful, general route to fabricate ordered mesoporous materials, but the precise tuning of the mesopore size generally requires trial and error to obtain the correct BCP template or appropriate swelling agent. Here, we demonstrate the ability to effectively modulate both expansion and contraction of the ordered cylindrical mesopores relative to those obtained from cooperatively assembled Pluronic F127, resol, and tetraethylorthosilicate. The two key physical parameters for the swelling agents are their hydrophobicity, as quantified by the octanol-water partition coefficient (Kow), and Hansen solubility parameters that describe the interactions of the solvent with the different components of the BCP template. Four low volatility solvents are examined that span a wide Kow with up to 90 wt % solvent relative to the Pluronic F127. Glycerol triacetate (Kow < 1) can decrease the average mesopore size from 5.9 to 4.8 nm due to segmental screening of the interactions in the Pluronic F127 to decrease chain stretching at intermediate loadings. A modest increase in mesopore size to 8.1 nm can be achieved with trimethylbenzene (TMB, Kow = 3.42). Dioctyl phthalate (DOP), which is slightly more hydrophobic (Kow = 8.1), is more effective than TMB at expanding the pore size (maximum: 13.5 nm) without loss of ordered structure. A more hydrophobic solvent, tris (2-ethylhexyl) trimellitate (Kow = 12.5), is less effective at increasing the pore size (maximum: 8.2 nm). The Hansen solubility parameters for DOP most closely match those of the hydrophobic segment in the Pluronic F217 template. We attribute this similarity, which is related to the solvent quality, to the improved efficacy of DOP in increasing the pore size. These results illustrate that both the Hansen solubility parameters (relative to the hydrophobic segment of the template) and relative hydrophobicity of the swelling agent determine the obtainable pore sizes in cooperatively assembled ordered mesoporous materials.

Polyelectrolyte-micelle coacervates: intrapolymer-dominant vs. interpolymer-dominant association, solute uptake and rheological properties.

The effects of polyelectrolyte charge density, polyelectrolyte-to-surfactant ratio, and micelle species on coacervation were studied by turbidity, dynamic light scattering, and zeta potential measurements to examine the coacervation of the weak polyelectrolyte branched polyethylenimine (BPEI) and oppositely charged sodium dodecyl sulfate (SDS) micelles as well as BPEI and mixed micelles composed of SDS and poly(ethylene glycol) 4-nonylphenyl 3-sulfopropyl ether potassium salt (PENS). The results of dynamic light scattering and zeta potential measurements are discussed in terms of pH and BPEI-to-surfactant ratio. An intrapolymer-dominant to interpolymer-dominant association model for the BPEI-micelle coacervates was proposed based on the variation of size and zeta potential of coacervate particles by their BPEI-to-surfactant ratio. The partition coefficient of solutes into BPEI-micelle coacervates was determined using UV-vis measurements as a function of pH, BPEI-to-surfactant ratio, and mixed micelle composition. Both the hydrophobicity of solutes and micelles, as well as the association mode of coacervates, impact the solute uptake efficiency. Dynamic rheological measurements on the coacervates suggest that the rheological properties of the complex coacervates are impacted by the association mode of the coacervates as well as the charge density on BPEI chains during coacervation.

Strain rate dependent nanostructure of hydrogels with reversible hydrophobic associations during uniaxial extension.

An energy dissipation mechanism during deformation is required to impart toughness to hydrogels. Here we describe how in situ small angle X-ray scattering (SAXS) provides insight into possible energy dissipation mechanisms for a tough hydrogel based on an amphiphilic copolymer where nanoscale associations of the hydrophobic moieties act as effective crosslinks. The mechanical properties of the hydrogels are intimately coupled with the nanostructure that provides reversible crosslinks and evolves during deformation. As the extension rate increases, more mechanical energy is dissipated from rearrangements of the crosslinks. The scattering is consistent with hopping of hydrophobes between the nanoscale aggregates as the primary rearrangement mechanism. This rearrangement changes the network conformation that leads to non-affine deformation, where the change in the nanostructure dimension from SAXS is less than 15% of the total macroscopic strain. These nanostructure changes are rate dependent and correlated with the relaxation time of the hydrogel. At low strain rate (0.15% s-1), no significant change of the nanostructure was observed, whereas at higher strain rates (1.5% s-1 and 8.4% s-1) significant nanostructure anisotropy occurred during extension. These differences are attributed to the ability for the network chains to rearrange on the time scale of the deformation; when the characteristic time for extension is longer than the average segmental relaxation time, no significant change in nanostructure occurs on uniaxial extension. These results illustrate the importance of strain rate in the mechanical characterization and consideration of relaxation time in the design of tough hydrogels with reversible crosslinks.

Quantitative Rheometry of Thin Soft Materials Using the Quartz Crystal Microbalance with Dissipation.

In the inertial limit, the resonance frequency of the quartz crystal microbalance (QCM) is related to the coupled mass on the quartz sensor through the Sauerbrey expression that relates the mass to the change in resonance frequency. However, when the thickness of the film is sufficiently large, the relationship becomes more complicated and both the frequency and damping of the crystal resonance must be considered. In this regime, a rheological model of the material must be used to accurately extract the adhered film's thickness, shear modulus, and viscoelastic phase angle from the data. In the present work we examine the suitability of two viscoelastic models, a simple Voigt model ( Physica Scripta 1999, 59, 391-396) and a more realistic power-law model ( Langmuir 2015, 31, 4008-4017), to extract the rheological properties of a thermoresponsive hydrogel film. By changing temperature and initial dry film thickness of the gel, the operation of QCM was traversed from the Sauerbrey limit, where viscous losses do not impact the frequency, through the regime where the QCM response is sensitive to viscoelastic properties. The density-shear modulus and the viscoelastic phase angle from the two models are in good agreement when the shear wavelength ratio, d/λ n, is in the range of 0.05-0.20, where d is the film thickness and λ n is the wavelength of the mechanical shear wave at the nth harmonic. We further provide a framework for estimating the physical properties of soft materials in the megahertz regime by using the physical behavior of polyelectrolyte complexes. This provides the user with an approximate range of allowable film thicknesses for accurate viscoelastic analysis with either model, thus enabling better use of the QCM-D in soft materials research.

Sulfur Diffusion within Nitrogen-Doped Ordered Mesoporous Carbons Determined by in Situ X-ray Scattering.

The low intrinsic conductivity of sulfur necessitates conductive additives, such as mesoporous carbons, to the cathode to enable high-performance metal-sulfur batteries. Simultaneous efforts to address polysulfide shuttling have introduced nitrogen-doped carbons to provide both conductivity and suppressed shuttling because of their strong interaction with sulfur. The strength of this interaction will impact the ability to fill the mesopores with sulfur via melt infusion. Here, we systematically investigate how nitrogen doping influences the rate that molten sulfur can infiltrate the mesopores and the overall extent of pore filling of highly ordered mesoporous doped carbons using in situ small angle X-ray scattering (SAXS). The similarity in electron density between molten sulfur and the soft carbon framework of the mesoporous material leads to a precipitous decrease in the scattered intensity associated with the ordered structure as voids are filled with sulfur. As the nitrogen doping increases from 1 to 20 at. %, the effective diffusivity of sulfur in the mesopores decreases by an order of magnitude (2.7 × 10-8 to 2.3 × 10-9 cm/s). The scattering becomes nearly invariant within 20 min of melt infiltration at 155 °C for all but the most doped carbon, which indicates that submicron-sized mesoporous carbon particles can be filled rapidly. Additionally, the nitrogen doping decreases the sulfur content that can be accommodated within the mesopores from 95% of the mesopores filled without doping to only 64% filled with 20 at. % N as determined by the residual scattering intensity. Sulfur does not crystallize within the mesopores of the nitrogen-doped carbons, which is further indicative of the strong interactions between the nitrogen species and sulfur that can inhibit polysulfide shuttling. In situ SAXS provides insights into the diffusion of sulfur in mesopores and how the surface chemistry of nitrogen-doped carbon appears to significantly hinder the infiltration by sulfur.

Mechanical properties of bulk graphene oxide/poly(acrylic acid)/poly(ethylenimine) ternary polyelectrolyte complex.

Ternary complexes formed in a single pot process through the mixing of cationic (branched polyethylenimine, BPEI) and anionic (graphene oxide, GO, and poly(acrylic acid), PAA) aqueous solutions exhibit superior mechanical performance in comparison to their binary analogs. The composition of the ternary complex can be simply tuned through the composition of the anionic solution, which influences the water content and mechanical properties of the complex. Increasing the PAA content in the complex decreases the overall water content due to improved charge compensation with the BPEI, but this change also significantly improves the toughness of the complex. Ternary complexes containing ≤32 wt% PAA were too brittle to generate samples for tensile measurements, while extension in excess of 250% could be reached with 57 wt% PAA. From this work, the influence of GO and PAA on the mechanical properties of GO/PAA/BPEI complexes were elucidated with GO sheets acting to restrain the viscous flow and improve the mechanical strength at low loading (<12.6 wt%) and PAA more efficiently complexes with BPEI than GO to generate a less swollen and stronger network. This combination overcomes the brittle nature of GO-BPEI complexes and viscous creep of PAA-BPEI complexes. Ternary nanocomposite complexes appear to provide an effective route to toughen and strengthen bulk polyelectrolyte complexes.

Impact of surface wettability on dynamics of supercooled water confined in nitrogen-doped ordered mesoporous carbon.

Confinement of water to nanoscale dimensions enables substantial supercooling through disruption of the hydrogen bonding network. However, there remain questions associated with the importance of the nature of the water-surface interactions relative to physical confinement defined by the pore geometry on the dynamics of supercooled water. Here, a simple route to tune the surface wetting properties through nitrogen doping of carbon is reported. This method leads to nearly indistinguishable mesopore sizes to enable separation of surface wettability and pore size effects. Quasielastic neutron scattering (QENS) is used to probe the proton dynamics of water confined within the mesopores with an average diameter of 4.85 ± 0.05 nm as a function of temperature from 267 K to 189 K. The motions of water in the mesopores follow jump-diffusion. For the temperatures examined, the diffusivity of water in the mesopores decreases with increasing nitrogen doping of the carbon framework. The activation energy associated with proton dynamics increases by approximately 30% with N-doping when compared to the undoped carbon surface, which is attributed to the enhanced surface wettability (favorable interactions between water and pore surface). This acts to provide an energy barrier for the water motions. This work suggests that the influence of surface chemistry on the dynamics of supercooled water confined in mesopores is less than the influence of nanopore size.

Transport-Limited Adsorption of Plasma Proteins on Bimodal Amphiphilic Polymer Co-Networks: Real-Time Studies by Spectroscopic Ellipsometry.

Traditional hydrogels are commonly limited by poor mechanical properties and low oxygen permeability. Bimodal amphiphilic co-networks (ß-APCNs) are a new class of materials that can overcome these limitations by combining hydrophilic and hydrophobic polymer chains within a network of co-continuous morphology. Applications that can benefit from these improved properties include therapeutic contact lenses, enzymatic catalysis supports, and immunoisolation membranes. The continuous hydrophobic phase could potentially increase the adsorption of plasma proteins in blood-contacting medical applications and compromise in vivo material performance, so it is critical to understand the surface characteristics of ß-APCNs and adsorption of plasma proteins on ß-APCNs. From real-time spectroscopic visible (Vis) ellipsometry measurements, plasma protein adsorption on ß-APCNs is shown to be transport-limited. The adsorption of proteins on the ß-APCNs is a multistep process with adsorption to the hydrophilic surface initially, followed by diffusion into the material to the internal hydrophilic/hydrophobic interfaces. Increasing the cross-linking of the PDMS phase reduced the protein intake by limiting the transport of large proteins. Moreover, the internalization of the proteins is confirmed by the difference between the surface-adsorbed protein layer determined from XPS and bulk thickness change from Vis ellipsometry, which can differ up to 20-fold. Desorption kinetics depend on the adsorption history with rapid desorption for slow adsorption rates (i.e., slow-diffusing proteins within the network), whereas proteins with fast adsorption kinetics do not readily desorb. This behavior can be directly related to the ability of the protein to spread or reorient, which affects the binding energy required to bind to the internal hydrophobic interfaces.

A family of mechanically adaptive supramolecular graphene oxide/poly(ethylenimine) hydrogels from aqueous assembly.

Composite hydrogels containing graphene oxide (GO) offer advantageous mechanical properties, but tuning these properties generally requires the synthesis of new hydrogels or if the hydrogel is thermally responsive, utilization of a chemistry determined temperature window. Here, we demonstrate a simple route to generate a family of GO-based hydrogels from aqueous solution based assembly of GO with polycationic poly(ethylenimine), PEI, without any secondary chemical crosslinking. Tuning the ratio of GO : PEI during the assembly produces a family of hydrogels that responds to mechanical compression by irreversibly altering their equilibrium water content and mechanical properties in a controllable manner. Despite the lack of chemical crosslinks, the hydrogels are stable when stored in an excess of water or NaCl solutions (up to 1 M) and exhibit a tunable swelling ratio (mass hydrogel : mass solid) between 44 and 162 based on both composition and compression history. Consequently, the storage modulus from shear rheology can be increased by more than 3 orders of magnitude from this irreversible mechanical compression of the hydrogel. This stiffening of the hydrogels in response to mechanical stimuli enables the prior compression loading of the hydrogel to be determined. We demonstrate that this strategy is generalizable to other anionic 2D materials such as clay (cloisite). This family of mechanically adaptive hydrogels enables facile fabrication and tuning of physical properties that could be advantageous for sensing, energy dissipation, and other applications.

Rapid assessment of crystal orientation in semi-crystalline polymer films using rotational zone annealing and impact of orientation on mechanical properties.

Crystal orientation in semi-crystalline polymers tends to enhance their performance, such as increased yield strength and modulus, along the orientation direction. Zone annealing (ZA) orients the crystal lamellae through a sharp temperature gradient that effectively directs the crystal growth, but the sweep rate (VZA) of this gradient significantly impacts the extent of crystal orientation. Here, we demonstrate rotational zone annealing (RZA) as an efficient method to elucidate the influence of VZA on the crystal morphology of thin films in a single experiment using isotactic poly(1-butene), PB-1, as a model semi-crystalline polymer. These RZA results are confirmed using standard, serial linear ZA to tune the structure from an almost unidirectional oriented morphology to weakly oriented spherulites. The overall crystallinity is only modestly changed in comparison to isothermal crystallization (maximum of 55% from ZA vs. 48% for isothermal crystallization). However, the average grain size increases and the spherulites become anisotropic from ZA. Due to these structural changes, the Young's modulus of the oriented films, both parallel and perpendicular to the spherulite orientation direction, is significantly increased by ZA. The modulus does become anisotropic after ZA due to the directionality in the crystal structure, with more than a threefold increase in the modulus parallel to the orientation direction for the highest oriented film in comparison to the modulus from isothermal crystallization. RZA enables rapid identification of conditions to maximize orientation of crystals in thin polymer films, which could find utility in determining conditions to improve crystallinity and performance in organic electronics.