Recycling the High-Salinity Textile Wastewater by Quercetin-Based Nanofiltration Membranes with Minimal Water and Energy Consumption.

Effective recovery of dyes and salts from textile wastewater by nanofiltration (NF) remains a serious challenge due to the high consumption of water and energy caused by the limited performance of the available membranes. Herein, a novel strategy is described to prepare loose polyester NF membranes by using renewable quercetin as the aqueous monomer for fractionation of high salinity textile wastewater with minimal water and energy consumption. Compared with NF270, taken as the reference membrane, the QE-0.2/TMC-0.2 membrane significantly improved the efficiency for dye/salt fractionation by 288%. The water consumption was also decreased by 42.9%. The efficiency is attributed to an ultrahigh water permeance of 198 ± 2.1 L-1 m-2 h-1 bar-1 with a high selectivity of 123 (extremely low NaCl rejection of 1.6% and high Congo red rejection of 99.2%). The optimal quercetin-based membrane had an ultrathin separation layer of about 39 ± 1.2 nm with good hydrophilicity and negative charge density. Moreover, this work includes a novel method of comparison with a theoretically ideal membrane, which shows that both the energy and water consumption are near their theoretical minimum. This strategy is expected to save energy and minimize carbon emissions for membrane-based wastewater treatment systems.

Various Approaches to Studying the Phase Transition in an Octamethylcyclotetrasiloxane Crystal: From X-ray Structural Analysis to Metadynamics.

The structure, thermodynamic parameters, and the character of thermal motion in octamethylcyclotetrasiloxane (D4) were investigated using the combination of experimental (single-crystal X-ray diffraction, thermochemistry) and theoretical (density functional theory calculations, ab initio molecular dynamics and metadynamics) methods. Single crystals of D4 were grown in a glass capillary in situ and the structures of high- (238-270 K) and low-temperature (100-230 K) phases were studied in detail. In the temperature interval 230-238 K, a phase transition with rather low enthalpy (-1.04(7) kcal/mol) was detected. It was found that phase transition is accompanied by change of conformation of cyclosiloxane moiety from boat-saddle (cradle) to chair. According to PBE0/6-311G(d,p) calculation of isolated D4, such conformation changes are characterized by a low barrier (0.07 kcal/mol). The character of molecular thermal motion and the path of phase transition were established with combination of periodic DFT calculations, including molecular dynamics and metadynamics. The effect of crystal field led to an increase in the calculated phase transition barrier (4.27 kcal/mol from low- to high-temperature phase and 3.20 kcal/mol in opposite direction).

Synthesis, Structure and Electrochemical Properties of Acetamide- and Caprolactam-Containing Silicon Catecholates.

Hexacoordinated heteroligand silicon catecholates, although being prospective as easily soluble compounds with high hydrolytic stability and diverse redox properties, have been insufficiently studied. The transesterification of 1-(trimethoxysilylmethyl)-2-oxohexahydroaze or N-methyl-N-(trimethoxysilylmethyl)acetamide by two equivalents of catechol derivatives in the presence of dicyclohexylamine afforded a series of target compounds in good yield. The complexes were characterized using elemental analysis, FTIR, 1H, 13C and 29Si NMR spectra, X-ray crystallography and cyclic voltammetry. X-ray diffraction confirmed that the silicon atom possesses the octahedral geometry of the SiCO5 polyhedron that remains unchanged in solution as it follows from 29Si NMR data. The compounds demonstrated up to three oxidation waves; and the reduction profile strongly depended on the nature of the substituents on a catecholate anion.

Trapping of Difluorocarbene by Frustrated Lewis Pairs.

Frustrated Lewis pairs consisting of diphenylphosphino and boryl groups located at the ortho-position can trap difluorocarbene affording stable zwitterionic adducts. The reaction can be reversed to release difluorocarbene at elevated temperatures.

Aerobic Co-/ N-Hydroxysuccinimide-Catalyzed Oxidation of p-Tolylsiloxanes to p-Carboxyphenylsiloxanes: Synthesis of Functionalized Siloxanes as Promising Building Blocks for Siloxane-Based Materials.

Synthesis of organosilicon products with a "polar" functional group within organic substituents is one of the most fundamentally and practically important challenges in today's chemistry of silicones. In our study, we suggest a solution to this problem, viz., a high-efficiency preparative method based on aerobic Co-/ N-hydroxysuccinimide (NHSI) catalyzed oxidation of p-tolylsiloxanes to p-carboxyphenylsiloxanes. This approach is based on "green", commercially available, simple, and inexpensive reagents and employs mild reaction conditions: Co(OAc)2/NHSI catalytic system, O2 as the oxidant, process temperature from 40 to 60 °C, atmospheric pressure. This reaction is general and allows for synthesizing both mono- and di-, tri-, and poly( p-carboxyphenyl)siloxanes with p-carboxyphenyl groups at 1,1-, 1,3-, 1,5-, and 1,1,1-positions. All the products were obtained and isolated in gram amounts (up to 5 g) and in high yields (80-96%) and characterized by NMR, ESI-HRMS, GPC, IR, and X-ray data: p-carboxyphenylsiloxanes in crystalline state form HOF-like structures. Furthermore, it was shown that the suggested method is applicable for the oxidation of organic alkylarene derivatives (Ar-CH3, Ar-CH2-R) to the corresponding acids and ketones (Ar-C(O)OH and Ar-C(O)-R), as well as hydride silanes ([Si]-H) to silanols ([Si]-OH). The possibility of synthesizing monomeric (methyl) and polymeric (siloxane-containing PET analogue, Sila-PET) esters based on 1,3-bis( p-carboxyphenyl)disiloxane was studied. These processes occur with retention of the organosiloxane frame and allow to obtain the corresponding products in 90 and 99% yields.

Conduction properties of thin films from a water soluble carbon nanotube/hemicellulose complex.

We have examined the conductive properties of carbon nanotube based thin films, which were prepared via dispersion in water by non-covalent functionalization of the nanotubes with xylan, a type of hemicellulose. Measurements of low temperature conductivity, Kelvin probe force microscopy, and high frequency (THz) conductivity elucidated the intra-tube and inter-tube charge transport processes in this material. The measurements show excellent conductive properties of the as prepared thin films, with bulk conductivity up to 2000 S cm-1. The transport results demonstrate that the hemicellulose does not seriously interfere with the inter-tube conductance.

Scanning probe microscopy induced surface modifications of the topological insulator Bi2Te3 in different environments.

We investigated the topological insulator (TI) Bi2Te3 in four different environments (ambient, ultra-high vacuum (UHV), nitrogen gas and organic solvent environment) using scanning probe microscopy (SPM) techniques. Upon prolonged exposure to ambient conditions and organic solvent environments the cleaved surface of the pristine Bi2Te3 is observed to be strongly modified during SPM measurements, while imaging of freshly cleaved Bi2Te3 in UHV and nitrogen gas shows considerably less changes of the Bi2Te3 surface. We conclude that the reduced surface stability upon exposure to ambient conditions is triggered by adsorption of molecular species from ambient, including H2O, CO2, etc which is verified by Auger electron spectroscopy. Our findings of the drastic impact of exposure to ambient on the Bi2Te3 surface are crucial for further in-depth studies of the intrinsic properties of the TI Bi2Te3 and for potential applications that include room temperature TI based devices operated under ambient conditions.

Polycationic ligands of different chemical classes stimulate DNA strand displacement between short oligonucleotides in a protein-free system.

The ability of polycationic ligands to stimulate DNA strand displacement between short oligonucleotides in a protein-free system is demonstrated. We show that two ligands, tetracationic aliphatic amine (spermine) and a dicationic intercalating drug (chloroquine), promote strand displacement in a concentration-dependent manner. At low concentrations both ligands decelerate spontaneous strand displacement because of their impact on the stability of the DNA duplex. At elevated concentrations they accelerate strand displacement via formation of intermediate structures containing three DNA strands. The rate of the last process does not correlate with the thermal dissociation rate of the entire DNA duplex. It indicates that, possibly, the action of these agents cannot be explained by their influence on the stability of the DNA duplex. In general, our results suggest that the ability to stimulate DNA strand displacement appears to be a common feature of polycations of different chemical and structural classes. © 2016 Wiley Periodicals, Inc. Biopolymers 105: 633-641, 2016.

The dual role of HOP2 in mammalian meiotic homologous recombination.

Deletion of Hop2 in mice eliminates homologous chromosome synapsis and disrupts double-strand break (DSB) repair through homologous recombination. HOP2 in vitro shows two distinctive activities: when it is incorporated into a HOP2-MND1 complex it stimulates DMC1 and RAD51 recombination activities and the purified HOP2 alone is proficient in promoting strand invasion. We observed that a fraction of Mnd1(-/-) spermatocytes, which express HOP2 but apparently have inactive DMC1 and RAD51 due to lack of the HOP2-MND1 complex, exhibits a high level of chromosome synapsis and that most DSBs in these spermatocytes are repaired. This suggests that DSB repair catalyzed solely by HOP2 supports homologous chromosome pairing and synapsis. In addition, we show that in vitro HOP2 promotes the co-aggregation of ssDNA with duplex DNA, binds to ssDNA leading to unstacking of the bases, and promotes the formation of a three-strand synaptic intermediate. However, HOP2 shows distinctive mechanistic signatures as a recombinase. Namely, HOP2-mediated strand exchange does not require ATP and, in contrast to DMC1, joint molecules formed by HOP2 are more sensitive to mismatches and are efficiently dissociated by RAD54. We propose that HOP2 may act as a recombinase with specific functions in meiosis.

CO Oxidation over Pd/ZrO2 Catalysts: Role of Support's Donor Sites.

A series of supported Pd/ZrO2 catalysts with Pd loading from 0.2 to 2 wt % was synthesized. The ZrO2 material prepared by a similar technique was used as a reference sample. The samples have been characterized by means of transmission electron microscopy (TEM), X-ray diffraction analysis (XRD), X-ray photoelectron spectroscopy (XPS), temperature-programmed reduction (TPR), testing reaction of ethane hydrogenolysis (HGE), N2 adsorption, and electron paramagnetic resonance (EPR) spectroscopy. 1,3,5-trinitrobenzene was used as a probe molecule for the EPR spin probe method. The catalytic performance of samples was tested in the model reaction of CO oxidation. It was shown that the concentration of donor sites of support measured by EPR spin probe correlates with catalytic behavior during light-off tests. Low concentration of donor sites on a support's surface was found to be caused by the presence of the specific surface defects that are related to existence of coordinately unsaturated structures.

Coupling of α,α-difluoro-substituted organozinc reagents with 1-bromoalkynes.

α,α-Difluoro-substituted organozinc reagents generated from conventional organozinc compounds and difluorocarbene couple with 1-bromoalkynes affording gem-difluorinated alkynes. The cross-coupling proceeds in the presence of catalytic amounts of copper iodide in dimethylformamide under ligand-free conditions.

Solid-State Transformations of Mayenite and Core-Shell Structures of C12A7@C Type at High Pressure, High Temperature Conditions.

Calcium aluminate of a mayenite structure, 12CaO∙7Al2O3 (C12A7), is widely applicable in many fields of modern science and technology. Therefore, its behavior under various experimental conditions is of special interest. The present research aimed to estimate the possible impact of the carbon shell in core-shell materials of C12A7@C type on the proceeding of solid-state reactions of mayenite with graphite and magnesium oxide under High Pressure, High Temperature (HPHT) conditions. The phase composition of the solid-state products formed at a pressure of 4 GPa and temperature of 1450 °C was studied. As is found, the interaction of mayenite with graphite under such conditions is accompanied by the formation of an aluminum-rich phase of the CaO∙6Al2O3 composition, while in the case of core-shell structure (C12A7@C), the same interaction does not lead to the formation of such a single phase. For this system, a number of hardly identified calcium aluminate phases along with the carbide-like phrases have appeared. The main product of the interaction of mayenite and C12A7@C with MgO under HPHT conditions is the spinel phase Al2MgO4. This indicates that, in the case of the C12A7@C structure, the carbon shell is not able to prevent the interaction of the oxide mayenite core with magnesium oxide located outside the carbon shell. Nevertheless, the other solid-state products accompanying the spinel formation are significantly different for the cases of pure C12A7 and C12A7@C core-shell structure. The obtained results clearly illustrate that the HPHT conditions used in these experiments lead to the complete destruction of the mayenite structure and the formation of new phases, which compositions differ noticeably depending on the precursor used-pure mayenite or C12A7@C core-shell structure.

Characterization of electron donor sites on Al2O3 surface.

Formation of radical anions after adsorption of 1,3,5-trinitrobenzene (TNB) on electron donor sites of fully oxidized Al(2)O(3) samples with different phase compositions is studied by EPR. It is shown that the maximum concentration of the radical anions does not substantially depend on the choice of solvent and reaction temperature, and can be used to measure the total concentration of the donor sites. The donor sites are observed in almost the same concentration about 5 × 10(16) m(-2) on all alumina polymorphs except for α-Al(2)O(3). The formation rate of the TNB radical anions and the activation energy of this process are found to depend on the donor properties of the solvent. The EPR in situ experiments showed that a substantial amount of the adsorbate forming a liquid phase is required for generation of the radical anions. These results prove that the sites measured by the formation of the TNB radical anions are not genuine electron donor sites capable of direct electron transfer to the adsorbed TNB molecules. A model of the observed paramagnetic species based on the obtained experimental data and the results of quantum chemical simulations is suggested. According to this model, a TNB radical anion substitutes a hydroxyl group forming a neutral ion pair with a surface aluminum cation. The suggested mechanism for the formation of such ion pairs involves the migration of simple radicals and does not require long-distance charge separation. It is supposed that the donor site where the process is initiated includes a negatively charged surface hydroxyl group.

Mayenite Synthesis from Hydroxide Precursors: Structure Formation and Active Sites on Its Surface.

We studied the formation process of a mayenite structure from hydroxide precursors in different gas media. According to X-ray diffraction data, this method allows a well-crystallized mayenite (Ca12Al14O33 or C12A7) phase to be obtained at low (500-900 °C) temperatures with an insignificant impurity of CaO. It was shown that the lattice parameters for C12A7 obtained in an inert atmosphere (Ar) were lower when compared with similar samples in the air. These results can be explained by the different levels of oxygen nonstoichiometry in the resulting phase. We noted that sintering and crystallization of mayenite proceeds at lower temperatures in Ar than in the air medium. We found the presence of donor and acceptor active sites on the surface of mayenite, which was detected by the spin probe method. The specific (per unit surface) concentration of such sites (2.5 × 1016 m-2 and 1.5 × 1015 m-2 for donor and acceptor sites, respectively) is comparable to that of γ-Al2O3, which is traditionally used as catalyst support. This allows it to be used in adsorption and catalytic technologies, taking into account its high specific surface area (~30-50 m2/g at a low synthesis temperature).

Aluminothermic Synthesis of Dispersed Electrides Based on Mayenite: XRD and EPR Study.

The evolution of the structure and the phase composition of a dispersed mayenite at its interaction with metallic aluminum was studied in a temperature range from 900 to 1400 °C in both argon and air atmospheres. The aluminum loading was varied from 0 to 50 wt%. It was found that the addition of aluminum significantly affects the stability of the mayenite and other calcium aluminate phases within the studied temperature range. The formation of the electride state registered by the appearance of a characteristic electron paramagnetic resonance (EPR) signal from F+-like centers (g~1.994) in an argon atmosphere was shown to take place already at 1150 °C due to an aluminothermic reduction of this material. The super-narrow (Hp-p < 0.5 G) EPR spectra from F+-like centers, which were recently observed for the core−shell structures of the C12A7@C type only, were registered for mayenite for the first time. The results obtained in the present study testify firstly towards the possibility of significantly diminishing the temperatures required for the formation of the electride state in such systems and secondly towards the ability to stabilize the size of small electride nanoparticles within the synthesized calcium aluminate matrix.

Resistance Switching in Polycrystalline C12A7 Electride.

The memory (memristive) properties of an electride material based on polycrystalline mayenite (C12A7:e-) were studied. The phase composition of the material has been confirmed by such methods as XRD, TEM, Raman, and infrared spectroscopy. The electride state was confirmed by conductivity measurements and EPR using a characteristic signal from F+-like centers, but the peak at 186 cm-1, corresponding to an electride with free electrons, was not observed explicitly in the Raman spectra. The temperature dependence of current-voltage characteristics in states with low and high resistance (LRS and HRS) has been studied. In the LRS state, the temperature dependence of the current has a non-Arrhenius character and is described by the Hurd quantum tunnelling model with a Berthelot temperature of 262 K, while in the HRS state, it can be described in terms of the Arrhenius model. In the latter case, the existence of two conduction regions, "impurity" and "intrinsic", with corresponding activation energies of 25.5 and 40.6 meV, was assumed. The difference in conduction mechanisms is most likely associated with a change in the concentration of free electrons.

Comparative Study on Carbon Erosion of Nickel Alloys in the Presence of Organic Compounds under Various Reaction Conditions.

The processes of carbon erosion of nickel alloys during the catalytic pyrolysis of organic compounds with the formation of carbon nanofibers in a flow-through reactor as well as under reaction conditions in a close volume (Reactions under Autogenic Pressure at Elevated Temperature, RAPET) were studied. The efficiency of the ferromagnetic resonance method to monitor the appearance of catalytically active nickel particles in these processes has been shown. As found, the interaction of bulk Ni-Cr alloy with the reaction medium containing halogenated hydrocarbons (1,2-dichloroethane, 1-iodobutane, 1-bromobutane) results in the appearance of ferromagnetic particles of similar dimensions (~200-300 nm). In the cases of hexachlorobenzene and hexafluorobenzene, the presence of a hydrogen source (hexamethylbenzene) in the reaction mixture was shown to be highly required. The microdispersed samples of Ni-Cu and Ni-Mo alloys were prepared by mechanochemical alloying of powders and by reductive thermolysis of salts-precursors, accordingly. Their interaction with polymers (polyethylene and polyvinyl chloride) under RAPET conditions and with ethylene and 1,2-dichloroethane in a flow-through reactor are comparatively studied as well. According to microscopic data, the morphology of the formed carbon nanofibers is affected by the alloy composition and by the nature of the used organic substrate.

All-carbon phosphoranes via difluorocarbene trapping.

A reaction of intramolecularly disposed phosphonium and phenoxide (or thiophenoxide) fragments with difluorocarbene affording all-carbon λ5-phosphoranes is described. The presence of electron-withdrawing CHF2-groups at the phosphonium center is important for the phosphorane formation. In a phosphorane, both phenyl groups located in the equatorial positions undergo 1,2-P,C migration under thermal conditions.

ortho-Dialkylamino arylboranes as efficient reagents for difluorocarbene trapping.

Compounds bearing ortho-oriented dialkylamino and boryl groups can serve as efficient reagents to trap difluorocarbene leading to zwitterionic ammonium borates featuring N-CF2-B fragments. The reagents are shelf-stable and can be used as mechanistic probes for reactions proceeding via difluorocarbene.

Tetrahedral Silicon-Centered Dibenzoylmethanatoboron Difluorides: Synthesis, Crystal Structure, and Photophysical Behavior in Solution and the Solid State.

Four tetrahedral silicon-centered derivatives of dibenzoylmethanatoboron difluoride (DBMBF2 ) were synthesized and characterized. Their structural and optical features both in solution and the solid state were investigated by using X-ray crystallography, steady-state and time-dependent spectroscopy, and DFT-based calculations. In dilute solutions, the molar absorption coefficient increases from 40500 to 175200 M-1 cm-1 as the number of DBMBF2 fragments in a molecule increases from one to four, while, in contrast, the nonradiative rate constant of fluorescence decay decreases from 0.49 to 0.34. In the solid state, absorption and emission spectra depend on the degree of crystallinity and microcrystal size. The tris-DBMBF2 derivative forms fully overlapping dimeric structures that exhibit excimer-like fluorescence, which is accurately predicted by the quantum-chemical calculations. The mono-DBMBF2 derivative exhibits fully reverse mechanofluorochromic behavior.