Optimization and Parameter Investigation of the Planar Photocatalytic Microreactor.

The microreactor could break the limitation of mass transfer and photon transmission in photocatalysis. Through a facile assembly method, a planar photocatalytic microreactor was constructed to fit most of the photocatalysts regardless of their strict preparation method. This microreactor exhibits a 2.41-fold efficiency compared to a bulk reactor. Parameters that affect the photocatalytic performance were discussed in detail by experiment and calculation. The diffusion rate is the main bottleneck in a planar microreactor under a laminar flow. The microreactor with lower height shows higher efficiency owing to faster mass transfer, while the length and width affect slightly. Elevating the light power density provides a diminishing benefit. Faster flow speed reduces the apparent degradation percent but increases the chemical reaction rate, in fact. The reaction rate increases to 9.31 times by reducing the height from 500 to 100 µm and grows another 1.76 times by adding the flow speed from 10 to 40 mL/h. This work illustrates the influence of parameters on planar photocatalytic microreactors and offers a promising prospect for large-volume photocatalytic water treatment.

The rhizosphere Microbiome of Malus sieversii (Ldb.) Roem. in the geographic and environmental gradients of China's Xinjiang.

Malus sieversii (Ldb.) Roem. is the original species of modern cultivated apple and a key national essential conservation plant in China. In recent years, degradation and death of wild apple has been exacerbated by imbalances in the rhizosphere micro-ecosystems of wild apple forests due to soil nutrient loss, grazing, climate change and pest and disease outbreaks. However, the structure, diversity and response to environmental factors of wild apple rhizosphere microbial communities are so far unclear. In this study, the rhizosphere bacterial and eukaryotic communities of M. sieversii (Ldb.) Roem. in eight regions of the Yili River were analyzed using 16S/18S rDNA high-throughput sequencing technology. The results indicated that the bacterial operational taxonomic units (OTUs), Shannon index, and community composition were significantly lower in regions A, E, and F than in other regions. By contrast, the dominant eukaryotic communities in all regions were relatively similar in composition and differed less than the relative abundance of bacterial communities. Geographical and climatic distance were found to be key factors influencing the composition and diversity of wild apple rhizosphere microbial communities through mantel analysis. Moreover, these factors above were more correlated with bacterial diversity than with eukaryotes. This study identified the structure of wild apple rhizosphere microbial communities in Xinjiang and their interaction mechanisms under geographical and environmental gradients. It provides guidance for the sustainable management and ecological construction of wild apple forests in China.

ATXN3 promotes prostate cancer progression by stabilizing YAP.

BACKGROUND: Prostate cancer (PC) is the most common neoplasm and is the second leading cause of cancer-related deaths in men worldwide. The Hippo tumor suppressor pathway is highly conserved in mammals and plays an important role in carcinogenesis. YAP is one of major key effectors of the Hippo pathway. However, the mechanism supporting abnormal YAP expression in PC remains to be characterized. METHODS: Western blot was used to measure the protein expression of ATXN3 and YAP, while the YAP target genes were measured by real-time PCR. CCK8 assay was used to detect cell viability; transwell invasion assay was used to measure the invasion ability of PC. The xeno-graft tumor model was used for in vivo study. Protein stability assay was used to detect YAP protein degradation. Immuno-precipitation assay was used to detect the interaction domain between YAP and ATXN3. The ubiquitin-based Immuno-precipitation assays were used to detect the specific ubiquitination manner happened on YAP. RESULTS: In the present study, we identified ATXN3, a DUB enzyme in the ubiquitin-specific proteases family, as a bona fide deubiquitylase of YAP in PC. ATXN3 was shown to interact with, deubiquitylate, and stabilize YAP in a deubiquitylation activity-dependent manner. Depletion of ATXN3 decreased the YAP protein level and the expression of YAP/TEAD target genes in PC, including CTGF, ANKRD1 and CYR61. Further mechanistic study revealed that the Josephin domain of ATXN3 interacted with the WW domain of YAP. ATXN3 stabilized YAP protein via inhibiting K48-specific poly-ubiquitination process on YAP protein. In addition, ATXN3 depletion significantly decreased PC cell proliferation, invasion and stem-like properties. The effects induced by ATXN3 depletion could be rescued by further YAP overexpression. CONCLUSIONS: In general, our findings establish a previously undocumented catalytic role for ATXN3 as a deubiquitinating enzyme of YAP and provides a possible target for the therapy of PC. Video Abstract.

Recent advances in enhancing stereocomplexation between poly(lactide) enantiomeric chains.

Over the past three decades, its excellent biodegradability and biocompatibility have enabled poly(lactide) (PLA) to be extensively explored as a replacement for oil-based thermoplastics in biomedical and industrial applications. However, PLA homopolymers have "facilitative" limitations such as low mechanical properties, low processing temperatures, slow recrystallization, and insufficient crystallinity, which have usually hindered commercial PLA in industrial and biomedical applications. The formation of stereo-complexation between enantiomeric poly(L-lactide) (PLLA) and poly(D-lactide) (PDLA) chains offers an effective approach to PLA-based engineering materials with improved properties. In this review, we have understandably summarized recent progress in improving the SC crystallization of PLA-based plastics into two aspects, i.e., enantiomeric PLA homopolymers, and enantiomeric PLA-based copolymers. One important point to be noted is that much emphasis is focused on improving SC crystallization by enhancing interactions in the enantiomeric PLA-based copolymers. There is an insightful discussion about the effect of enhanced SC crystallization as well as intermolecular interactions between PLLA and PDLA chains in various stereocomplexable systems. Most importantly, this review starts with the basic understanding of SC crystallization and further elaborates on the rational mechanism of enhanced SC crystallization to provide a broad idea for broadening the road toward PLA-based materials.

Trends in total cholesterol control among American adults with hypercholesterolemia, 1988-2018.

BACKGROUND AND AIMS: Cholesterol control and management in patients with hypercholesterolemia are significant for the primary and secondary prevention of atherosclerotic cardiovascular disease. This study analyzed the trend of serum total cholesterol (TC) control (<240 mg/dL and <200 mg/dL) in American adults with hypercholesterolemia and thereby make some effective recommendations for the public health measures. METHODS AND RESULTS: Basing on the National Health and Nutrition Examination Survey (NHANES) data from 1988 to 2018 (12 cycles), we calculated the weighted and representative rate of patients with hypercholesterolemia who had controlled TC, and then described the trend. Among the adults with hypercholesterolemia, the age-adjusted rate of those whose TC was less than 240 mg/dL increased from 7.67% (95%CI: 5.94%-9.40%) in 1988-1991 to 58.52% (95%CI: 55.89%-61.15%) in 2013-2014 and then remained stable; and the age-adjusted rate of those whose TC was less than 200 mg/dL increased from 2.49% (95%CI: 1.48%-3.50%) in 1988-1991 to 44.58% (95%CI: 40.00%-49.16%) in 2017-2018. CONCLUSION: We concluded that the rate of controlling TC below 200 mg/dL among all patients had shown an increasing trend from 1988 to 2018 in America, while the rate of controlling TC below 240 mg/dL remained stable in recent years after an increasing.

Clinical implications of 3D printing technology in preoperative evaluation of partial nephrectomy. / 3D打印技术应用于肾部分切除术术前评估中的临床意义.

OBJECTIVES: Renal cancer is a common malignancy of the urinary system, and the partial nephrectomy is a common surgical modality for early renal cancer. 3D printing technology can create a visual three-dimensional model by using 3D digital models of the patient's imaging data. With this model, surgeons can perform preoperative assessment to clarify the location, depth, and blood supply of the tumor, which helps to develop preoperative plans and achieve better surgical outcomes. In this study, the R.E.N.A.L scoring system was used to stratify patients with renal tumors and to explore the clinical application value of 3D printing technology in laparoscopic partial nephrectomy. METHODS: A total of 114 renal cancer patients who received laparoscopic partial nephrectomy in Xiangya Hospital from June 2019 to December 2020 were enrolled. The patients were assigned into an experimental group (n=52) and a control group (n=62) according to whether 3D printing technology was performed, and the differences in perioperative parameters between the 2 groups were compared. Thirty-nine patients were assigned into a low-complexity group (4-6 points), 32 into a moderate-complexity group (7-9 points), and 43 into a high-complexity group (10-12 points) according to R.E.N.A.L score, and the differences in perioperative parameters between the experimental group and the control group in each score group were compared. RESULTS: The experimental group had shorter operative time, renal ischemia time, and postoperative hospital stay (all P<0.05), less intraoperative blood loss (P=0.047), and smaller postoperative blood creatinine change (P=0.032) compared with the control group. In the low-complexity group, there were no statistically significant differences between the experimental group and the control group in operation time, renal ischemia time, intraoperative blood loss, postoperative blood creatinine changes, and postoperative hospital stay (all P>0.05). In the moderate- and high- complexity groups, the experimental group had shorter operative time, renal ischemia time, and postoperative hospital stay (P<0.05 or P<0.001), less intraoperative blood loss (P=0.022 and P<0.001, respectively), and smaller postoperative blood creatinine changes (P<0.05 and P<0.001, respectively) compared with the control group. CONCLUSIONS: Compared with renal tumor patients with R.E.N.A.L score<7, renal cancer patients with R.E.N.A.L score≥7 may benefit more from 3D printing assessment before undergoing partial nephrectomy.

Chondroitin synthase-3 regulates nucleus pulposus degeneration through actin-induced YAP signaling.

Loss of chondroitin sulfate (CS) has been reported to play a key role during intervertebral disc degeneration (IDD). However, the detailed mechanism of CS and its synthases have not been elucidated. Since CS is mainly synthesized by chondroitin synthases 3 (Chsy3), here, the Chsy3 knockout mice are generated by using CRISPR-Cas9 and semi-cloning technology to study its mechanism during IDD. We find that CS and Chsy3 expression are decreased during IDD both in human and mice nucleus pulposus (NP) tissue, and knockout of Chsy3 shows that spontaneous IDD phenotype resembles that of human samples in the Chsy3-/- mice. Taking advantage of RNA-Seq data, we confirm increased catabolic and decreased anabolic changes in Chsy3-/- NP cells. By using bioinformatic analysis and validation, we find that Hippo signaling pathway is significantly downregulated, and the activation of Yap1 is mainly affected in Chsy3-/- NP cells. Furthermore, functional analyses have shown that Chsy3 could regulate NP cell degeneration by Actin tension mediated activation of Yap1, which is independent of Hippo/Lats signaling. In summary, our findings reveal a novel mechanism that depletion of CS-related Chsy3 can cause spontaneous intervertebral disc degeneration by mediating Yap activation through CS-related actin-tension in NP cells.

Inflammatory-sensitive CHI3L1 protects nucleus pulposus via AKT3 signaling during intervertebral disc degeneration.

Intervertebral disc degeneration (IDD) is the main cause of low back pain and the mechanism of which is far from fully revealed. Although inflammation directed nucleus pulposus (NP) extracellular matrix metabolism dysregulation is known to be the main cause of the degeneration process, few is known about the protective factors. Using high-throughput label-free proteomics, we found that inflammation-related autocrine factor Chitinase-3-like protein 1 (CHI3L1, or YKL-40) is highly expressed in the NP cells during degeneration. Immunohistochemical analysis show that the expression of CHI3L1 is NP tissue specific, and increase significantly during degeneration. Overexpression of CHI3L1 significantly decrease the catabolism, and increase the anabolism of extracellular matrix. Knockdown of CHI3L1 using siRNAs show the opposite results, which imply that the protective role of CHI3L1 in IDD. Using high-throughput RNA sequencing and functional analyses, we find that AKT3 expression and its phosphorylation is mainly regulated by CHI3L1. And lastly, the mechanism of which is also validated using human and mouse degenerated NP tissues. In summary, our findings show that the inflammation-related autocrine factor CHI3L1 is NP specific, and it protects IDD by promoting the AKT3 signaling, which may serve as a potential therapeutic target in intervertebral disc degeneration.

Neoadjuvant Chemotherapy Benefits Survival in High-Grade Upper Tract Urothelial Carcinoma: A Propensity Score-Based Analysis.

BACKGROUND: To evaluate the benefit of neoadjuvant chemotherapy (NAC) for survival in high-grade upper tract urothelial carcinoma (UTUC), a propensity score-based analysis was performed with high-grade UTUC patients from multiple urologic centers. METHODS: From three urologic centers, 48 high-grade UTUC patients who received chemotherapy followed by surgery (NAC group) and 72 high-grade UTUC patients who underwent initial surgery (no-NAC group) were involved in a propensity score-based analysis. After propensity score-based (1:1) matching, 37 patients receiving NAC and 37 patients not receiving NAC were followed. RESULTS: The patients who received NAC had improved disease-free survival (DFS) and overall survival (OS), with a 3-year DFS rate of 78.4% and an OS rate of 86.5% versus a 3-year DFS rate of 51.4% and an OS rate of 62.2% for those treated with initial surgery (P = 0.018 and P = 0.02, respectively). In the multivariate analysis, the NAC group had a lower risk for mortality [DFS hazard ratio (HR) 0.25; 95% confidence interval (CI) 0.10-0.62; P = 0.003; OS HR 0.22; 95% CI 0.085-0.57; P = 0.002]. The analysis of patient survival in matched subgroups showed that NAC was beneficial in terms of the 3-year DFS for the group with a cT of 3 or higher (DFS HR 0.37; 95% CI 0.14-0.94; P = 0.036) and the group that had tumor with hydronephrosis (DFS HR 0.31; 95% CI 0.11-0.87; P = 0.026). CONCLUSION: The study showed that NAC may be considered as an effective addition to surgery for the treatment in high-grade UTUC patients.

Holmium laser enucleation of the prostate versus thulium laser enucleation of the prostate for the treatment of large-volume prostates > 80 ml: 18-month follow-up results.

PURPOSE: To compare the perioperative and functional outcomes of holmium laser enucleation of the prostate (HoLEP) and thulium laser enucleation of the prostate (ThuLEP) for the treatment of large-volume benign prostatic hyperplasia (BPH) (> 80 ml). METHODS: A total of 116 consecutive patients with BPH were randomized to be treated surgically with either HoLEP (n = 58) or ThuLEP (n = 58), following the classical three-lobe enucleation technique. Follow-up was assessed at 1, 3, 6, 12 and 18 months after surgery. RESULTS: At 18 months, the lower urinary tract symptom index was improved significantly in both groups compared with the baseline values. The operative time (78.4 ± 8.0 vs. 71.4 ± 6.4 min) and enucleation time (61.2 ± 5.4 vs. 56.4 ± 8.4 min) were significantly shorter for ThuLEP compared to HoLEP (both p < 0.001). There were no significant differences between the two groups regarding morcellation time, resected weight, hemoglobin decrease, catheter time and hospital stay (p > 0.05). The HoLEP and ThuLEP groups had equivalent International Prostate Symptom Scores (3 [3-3] vs. 3 [3-3], p = 0.776), quality of life (1 [1-2] vs. 2 [1-2], p = 0.809), Qmax (25.3 ± 4.8 ml/s vs. 24.7 ± 4.4 ml/s, p = 0.470), postvoid residual urine (PVR) (6.1 [2.6-20.8] vs. 7.7 [3.1-22.8] ml, p = 0.449) and PSA (0.84 ± 0.32 vs. 0.90 ± 0.34 ml, p = 0.309) at 18 months postoperatively. CONCLUSION: Both HoLEP and ThuLEP relieve lower urinary tract symptoms in a comparable way with high efficacy and safety. ThuLEP was statistically superior to HoLEP in operation time and enucleation time, although the differences were clinically negligible.

Quantum Griffiths Phase Inside the Ferromagnetic Phase of Ni_{1-x}V_{x}.

We study by means of bulk and local probes the d-metal alloy Ni_{1-x}V_{x} close to the quantum critical concentration, x_{c}≈11.6%, where the ferromagnetic transition temperature vanishes. The magnetization-field curve in the ferromagnetic phase takes an anomalous power-law form with a nonuniversal exponent that is strongly x dependent and mirrors the behavior in the paramagnetic phase. Muon spin rotation experiments demonstrate inhomogeneous magnetic order and indicate the presence of dynamic fluctuating magnetic clusters. These results provide strong evidence for a quantum Griffiths phase on the ferromagnetic side of the quantum phase transition.

How capping protein enhances actin filament growth and nucleation on biomimetic beads.

Capping protein (CP), which caps the growing ends of actin filaments, accelerates actin-based motility. Recent experiments on biomimetic beads have shown that CP also enhances the rate of actin filament nucleation. Proposed explanations for these phenomena include (i) the actin funneling hypothesis (AFH), in which the presence of CP increases the free-actin concentration, and (ii) the monomer gating model, in which CP binding to actin filament barbed ends makes more monomers available for filament nucleation. To establish how CP increases the rates of filament elongation and nucleation on biomimetic beads, we perform a quantitative modeling analysis of actin polymerization, using rate equations that include actin filament nucleation, polymerization and capping, as modified by monomer depletion near the surface of the bead. With one adjustable parameter, our simulation results match previously measured time courses of polymerized actin and filament number. The results support a version of the AFH where CP increases the local actin monomer concentration at the bead surface, but leaves the global free-actin concentration nearly constant. Because the rate of filament nucleation increases with the monomer concentration, the increased local monomer concentration enhances actin filament nucleation. We derive a closed-form formula for the characteristic CP concentration where the local free-actin concentration reaches half the bulk value, and find it to be comparable to the global Arp2/3 complex concentration. We also propose an experimental protocol for distinguishing branching nucleation of filaments from spontaneous nucleation.

Load sharing in the growth of bundled biopolymers.

To elucidate the nature of load sharing in the growth of multiple biopolymers, we perform stochastic simulations of the growth of biopolymer bundles against obstacles under a broad range of conditions and varying assumptions. The obstacle motion due to thermal fluctuations is treated explicitly. We assume the "Perfect Brownian Ratchet" (PBR) model, in which the polymerization rate equals the free-filament rate as soon as the filament-obstacle distance exceeds the monomer size. Accurate closed-form formulas are obtained for the case of a rapidly moving obstacle. We find the following: (1) load sharing is usually sub-perfect in the sense that polymerization is slower than for a single filament carrying the same average force; (2) the sub-perfect behavior becomes significant at a total force proportional to the logarithm or the square root of the number of filaments, depending on the alignment of the filaments; (3) for the special case of slow barrier diffusion and low opposing force, an enhanced obstacle velocity for an increasing number of filaments is possible; (4) the obstacle velocity is very sensitive to the alignment of the filaments in the bundle, with a staggered alignment being an order of magnitude faster than an unstaggered one at forces of only 0.5 pN per filament for 20 filaments; (5) for large numbers of filaments, the power is maximized at a force well below 1 pN per filament; (6) for intermediate values of the obstacle diffusion coefficient, the shape of the force velocity relation is very similar to that for rapid obstacle diffusion.

Screening of rhizosphere nitrogen fixing, phosphorus and potassium solubilizing bacteria of Malus sieversii (Ldb.) Roem. and the effect on apple growth.

Nitrogen, phosphorus and potassium inorganic fertilizers are commonly used when growing apples, but their excessive application has resulted in a decline in soil fertility and therefore an inability to maintain sustainable cultivation systems. It is possible to compensate for this with biofertilizers. Nitrogen-fixing, phosphorus solubilizing, and potassium solubilizing bacteria are biofertilizers with a broad range of possible uses. In this study, beneficial microorganisms were screened from the rhizosphere soil of the apple tree, Malus sieversii (Ldb.) Roem., which is rich in microbial diversity in natural environments. It was essential to investigate their effects on the growth of apple seedlings. Eight populations of organic phosphorus solubilizing bacteria (56), inorganic phosphorus solubilizing bacteria (13), nitrogen-fixing bacteria (22), and potassium solubilizing bacteria (24) were isolated from eight populations of Xinjiang wild apple rhizosphere in Ili by medium culture. Their morphological characteristics were recorded and their activity was determined. The most active strains were Pseudomonas migulae, Pseudomonas poae, and Pseudomonas extremaustralis, which was determined by physiological and biochemical properties and 16S rDNA sequence analysis. The L16 (45) orthogonal experiment, which used the three strains as testing materials, was created to assess the effects of the strains on apple physiological indicators, soil nutrients, leaf nutrients, and biomass, as well as to identify the ideal combination, concentration, timing, and application method. The results indicated that the peroxidase (POD) and catalase (CAT) activities of apple seedlings increased significantly under the 10 treatment, and the (SOD) activities of the 0 (control) and 1 (inorganic fertilizer only) treatments were significantly lower than the other treatments; soluble sugar, soluble protein and chlorophyll contents increased in all treatments compared to 0 and 1, while malondialdehyde and proline contents increased or decreased compared to 0 and 1; apple seedlings in treatment 10 had the highest soil N, P, and K content, leaf N, P, and K content and biomass were also all highest in treatment 10. In summary, the strains screened for the test can be used as biofertilizers and the optimum application was determined for treatment 10, meaning that the results also provide a theoretical basis for their application in artificially grown orchards.

Paradoxical psoriasis induced by IL-17 antagonists.

Background The paradoxical occurrence of psoriasis triggered by Interleukin-17 (IL-17) inhibitors is notable due to its prominent symptoms and the therapeutic dilemma it presents for follow-up care. Objective To describe cases in our clinic, perform an in-depth literature review, and suggest the most probable mechanisms of action. Method We conducted a literature review on published cases of IL-17 inhibitor-induced psoriasis. Results We found 22 articles reporting 30 cases of IL-17 inhibitor-induced paradoxical psoriasis, primarily observed in patients with a previous psoriasis history. Almost 60% of cases showed a change in lesion morphology, with the plaque or pustular type being prevalent. About 73.3% of patients had to discontinue the implicated drug, leading to partial or complete symptom resolution. The mechanism behind this response seemed to involve IL-17 inhibitors downregulating Tumour Necrosis Factor alpha (TNF-α), subsequently upregulating plasmacytoid dendritic cells and triggering unopposed IFN-alpha (IFN-α) production. Limitation Data are confined to case reports and case series. Conclusion More assertive measures are recommended for treating paradoxical psoriasis induced by IL-17 inhibitors than those caused by TNF-α inhibitors. Reintroducing an IL-17 inhibitor is not advised, as patients did not show improvement.

Efficient liquid phase photothermal catalysis realized by Ag2O/Bi4O5I2via heat-localization in a microreactor.

By constructing a Ag2O/Bi4O5I2 p-n heterojunction and applying a heat-localization microreactor, efficient photocatalysis enhanced by both photoinduced carrier separation and the photothermal effect was realized. This work focuses on the utilization of near-infrared light to broaden the absorption spectrum and accelerate the transportation of carriers. Through the production and localization of heat, it provides a novel thought for full-spectrum photocatalysis.

Synthesis of MPEG-b-PLLA Diblock Copolymers and Their Crystallization Performance with PDLA and PLLA Composite Films.

Methoxy poly(ethylene glycol)-block-poly(L-lactide) (MPEG-b-PLLA) has a wide range of applications in pharmaceuticals and biology, and its structure and morphology have been thoroughly studied. In the experiment, we synthesized MPEG-b-PLLA with different block lengths using the principle of ring-opening polymerization by controlling the amount of lactic acid added. The thermodynamic properties of copolymers and the crystallization properties of blends were studied separately. The crystallization kinetics of PDLA/MPEG-b-PLA and PLLA/MPEG-b-PLA composite films were studied using differential scanning calorimetry (DSC). The results indicate that the crystallization kinetics of composite films are closely related to the amount of block addition. The crystallinity of the sample first increases and then decreases with an increase in MPEG-b-PLLA content. These results were also confirmed in polarized optical microscope (POM) and wide-angle X-ray diffraction (WAXD) tests. When 3% MPEG-b-PLLA was added to the PDLA matrix, the blend exhibited the strongest crystallization performance.

Elevating the Photocatalytic Performance of BiOCl by Promoting Light Utilization: From Co doping to the Microreactor.

Owing to its unique layered structure, BiOCl demonstrates high photocatalytic activity. However, its wide bandgap hinders the absorption of visible light. Doping modification is an effective method to expand the light absorption edge of photocatalysts by creating a doping energy level within the bandgap. Herein, Co as a variable valence element was used to dope the BiOCl nanosheets through a simple hydrothermal approach. As a result, the absorption edge of Co-BiOCl extends to the visible light region, and the photocatalytic performance was enhanced by 3.02 times. To overcome the shortcoming of photons being consumed easily in the bulk reactor, a planar microreactor was introduced to reduce the attenuation of light and accelerate the mass transfer. By comparison to the bulk reactor, a maximum of 15.3-fold additional activity promotion emerged. This work combines doping modification and reactor improvement to realize highly efficient photocatalysis in practical application.

Enhanced High-Fructose Corn Syrup Production: Immobilizing Serratia marcescens Glucose Isomerase on MOF (Co)-525 Reduces Co2+ Dependency in Glucose Isomerization to Fructose.

The escalating demand for processed foods has led to the widespread industrial use of glucose isomerase (GI) for high-fructose corn syrup (HFCS) production. This reliance on GIs necessitates continual Co2+ supplementation to sustain high catalytic activity across multiple reaction cycles. In this study, Serratia marcescens GI (SmGI) was immobilized onto surfaces of the metal-organic framework (MOF) material MOF (Co)-525 to generate MOF (Co)-525-GI for use in catalyzing glucose isomerization to generate fructose. Examination of MOF (Co)-525-GI structural features using scanning electron microscopy-energy dispersive spectroscopy, Fourier-transform infrared spectroscopy, and ultraviolet spectroscopy revealed no structural changes after SmGI immobilization and the addition of Co2+. Notably, MOF (Co)-525-GI exhibited optimal catalytic activity at pH 7.5 and 70 °C, with a maximum reaction rate (Vmax) of 37.24 ± 1.91 µM/min and Km value of 46.25 ± 3.03 mM observed. Remarkably, immobilized SmGI exhibited sustained high catalytic activity over multiple cycles without continuous Co2+ infusion, retaining its molecular structure and 96.38% of its initial activity after six reaction cycles. These results underscore the potential of MOF (Co)-525-GI to serve as a safer and more efficient immobilized enzyme technology compared to traditional GI-based food-processing technologies.

Conditional survival of male breast cancer.

BACKGROUND: The incidence of male breast cancer has been increasing in recent years; however, the long-term survival outcomes of diagnosed patients remain uncertain. This study was designed to evaluate the conditional survival of male breast cancer patients and to predict the future survival of patients through the conditional nomogram, to provide important suggestions for clinical decision-making. METHODS: Retrospective data from the SEER database included 3600 male breast cancer patients, divided into training and validation groups (7 : 3 ratio). Overall survival rates were calculated using Kaplan-Meier analysis. Conditional survival analysis described survival at specific years. Time-dependent multivariate Cox analysis identified prognostic factors' impact. The conditional survival nomogram model predicted real-time survival rates. RESULTS: Over time, the 5-year real-time survival rate of patients gradually improved, increasing from 70.5 to 74.8, 79.4, 85.8, and 92.9% (respectively, representing 5-year survival rates of 1-4 years after diagnosis). In addition, the improvement in conditional survival rate CS5 showed a nonlinear trend. After 5 years of diagnosis, age, tumor size, and tumor stage had a sustained impact on patient prognosis. Finally, a conditional survival nomogram was constructed to predict the 10-year survival rate in real time. CONCLUSION: Five years after diagnosis, the conditional survival rate of male patients with breast cancer has improved, but it is not nonlinear. In the first 5 years after diagnosis, patients with older age, larger tumor size, poorer tumor stage, and distant metastasis should be actively followed up and treated to improve their long-term survival.