In vitro toxicity evaluation in A549 cells of diesel particulate matter from two different particle sampling systems and several resuspension media.

In urban areas, inhalation of fine particles from combustion sources such as diesel engines causes adverse health effects. For toxicity testing, a substantial amount of particulate matter (PM) is needed. Conventional sampling involves collection of PM onto substrates by filtration or inertial impaction. A major drawback to those methodologies is that the extraction process can modify the collected particles and alter their chemical composition. Moreover, prior to toxicity testing, PM samples need to be resuspended, which can alter the PM sample even further. Lastly, the choice of the resuspension medium may also impact the detected toxicological responses. In this study, we compared the toxicity profile of PM obtained from two alternative sampling systems, using in vitro toxicity assays. One system makes use of condensational growth before collection in water in an impinger - BioSampler (CG-BioSampler), and the other, a Dekati® Gravimetric Impactor (DGI), is based on inertial impaction. In addition, various methods for resuspension of DGI collected PM were compared. Tested endpoints included cytotoxicity, formation of cellular reactive oxygen species, and genotoxicity. The alternative collection and suspension methods affected different toxicological endpoints. The water/dimethyl sulfoxide mixture and cell culture medium resuspended particles, along with the CG-BioSampler sample, produced the strongest responses. The water resuspended sample from the DGI appeared least toxic. CG-BioSampler collected PM caused a clear increased response in apoptotic cell death. We conclude that the CG-BioSampler PM sampler is a promising alternative to inertial impaction sampling.

The potential of thermal desorption-GC/MS-based analytical methods for the unambiguous identification and quantification of perfluoroisobutene and carbonyl fluoride in air samples.

The reactive gases perfluoroisobutene and carbonyl fluoride are highly toxic and difficult to analyze in air. For this paper, the available sampling and analysis methods involving gas chromatography/mass spectrometry were investigated for their potential to give unambiguous identification and quantification of perfluoroisobutene and carbonyl fluoride, for which no such methods exist. Although high concentrations of perfluoroisobutene could be analyzed directly by manual split injection, sorbent sampling followed by thermal desorption GC/MS allowed lower concentrations to be analyzed. However, a significant degradation of perfluoroisobutene observed after thermal desorption analysis inspired the use of derivatization of perfluoroisobutene with 3,4-dimercaptotoluene. The use of Tenax TA sorbent tubes spiked with 3,4-dimercaptotoluene and trimethylamine in a molar ratio of 1:8 proved successful for the quantification of a unique perfluoroisobutene derivative, and the method was validated for atmospheres in the range of 0.13-152 ppb with a relative standard deviation of less than 20% and an accuracy of 90%. Although carbonyl fluoride was less stable than perfluoroisobutene, direct analysis was possible at high concentrations but the response was not linear. The 3,4-dimercaptotoluene derivatization method developed was also applicable for quantification of carbonyl fluoride atmospheres.

Characterization of toxicological effects of complex nano-sized metal particles using in vitro human cell and whole blood model systems.

Metal oxide fumes form at high temperatures, for instance, during welding or firing ammunition. Inhalation exposure to high levels of airborne metal oxide particles can cause metal fume fever, cardiovascular effects, and lung damage in humans, but the associated underlying pathological mechanisms are still not fully understood. Using human alveolar epithelial cells, vascular endothelial cells, and whole blood model systems, we aimed to elucidate the short-term effects of well-characterized metal particles emitted while firing pistol ammunition. Human lung epithelial cells exposed to gunshot smoke particles (0.1-50 µg/ml) produced reactive oxygen species (ROS) and pro-inflammatory cytokines (interleukin 8 (IL-8), granulocyte-macrophage colony-stimulating factor (GM-CSF)) that activate and recruit immune cells. Particles comprising high copper (Cu) and zinc (Zn) content activated human endothelial cells via a non-ROS-mediated mechanism that triggered immune activation (IL-8, GM-CSF), leukocyte adhesion to the endothelium (soluble intercellular adhesion molecule 1 (sICAM-1)), and secretion of regulators of the acute-phase protein synthesis (interleukin 6 (IL-6)). In human whole blood, metal oxides in gunshot smoke demonstrated intrinsic properties that activated platelets (release of soluble cluster of differentiation 40 ligand (sCD40L), platelet-derived growth factor B-chain homodimer(PDGF-BB), and vascular endothelial growth factor A (VEGF-A)) and blood coagulation and induced concomitant release of pro-inflammatory cytokines from blood leukocytes that further orchestrate thrombogenesis. The model systems applied provide useful tools for health risk assessment of particle exposures, but more studies are needed to further elucidate the mechanisms of metal fume fever and to evaluate the potential risk of long-term cardiovascular diseases.

The toxic potential of a fourth-generation E-cigarette on human lung cell lines and tissue explants.

The use of electronic cigarettes (E-cigs) is rapidly increasing. The latest generation of E-cigs is highly customizable, allowing for high heating coil temperatures. The aim of this study was to assess the toxic potential of a fourth-generation E-cig. Aerosols generated from E-liquid with (24 mg/mL) and without nicotine, using a fourth-generation E-cig, were chemically analysed and compared with cigarette smoke (K3R4F). Human lung epithelial cell lines and distal lung tissue explants were exposed to E-cig vapour extract (EVE) and cigarette smoke extract for 24 hours and assessed for viability, inflammation, oxidative stress and genotoxicity. E-cig aerosols contained measurable levels of volatile organic compounds, aldehydes and polycyclic aromatic hydrocarbons, in general, to a much lesser extent than cigarette smoke. Higher levels of certain carbonyls, e.g. formaldehyde, were detected in the E-cig aerosols. EVEs decreased cell viability of BEAS-2B cells, whereas little effect was seen in A549 cells and distal lung tissue. The nicotine-containing EVE caused a greater decrease in cell viability and significant increase in DNA damage than the nicotine-free EVE. Increased cytotoxicity, reactive oxygen species production and genotoxicity were seen with cells and tissue exposed to cigarette smoke extract compared with EVEs. Although E-cig aerosols were less toxic than cigarette smoke, it was not benign. Moreover, the EVE containing nicotine was more toxic than the nicotine-free EVE. More research is needed on the short- and long-term health effects of vaping and the usage of newly emerging E-cig devices to evaluate better the potential negative effects of E-cigs on human health.

Passive personal air sampling of dust in a working environment-A pilot study.

The aim of this study was to make a preliminary evaluation of the University of North Carolina passive aerosol sampler (UNC sampler) for personal air sampling of particles. Nine personal air samplings of respirable fraction were conducted in an open-pit mine, with pairwise UNC samplers and a respirable cyclone mounted on the chest of workers. UNC samples were analyzed with scanning electron microscopy (SEM) and to some extent energy dispersive X-ray spectroscopy (EDS). Respirable cyclone filter samples were weighed. Correlations and particle elemental compositions were described. Microscopic imaging of the collection surface showed that the particles were heterogeneously deposited across the surface of the UNC sampler. Collected particles were shaped as gravel particles and the resulting particle size distribution in air showed a peak at ca. 3 µm aerodynamic diameter, similarly to what has previously been reported from the same mine. The elemental composition indicated mineral origin. All correlations between the airborne mass concentrations from UNC samplers and respirable cyclones (Pearson = 0.54 and Spearman = 0.43) and between pairs of parallel UNC samplers (Pearson = 0.55 and Spearman = 0.67) were weak. The UNC sampler mass concentrations were approximately 30 times higher than those measured with the respirable cyclone. In conclusion, the UNC sampler, when used for personal sampling in a mine, provides a reasonable particle size distribution and the deposited particles appeared to be of mineral origin and not from textile or skin but the approximately 30-fold overestimation of mass concentrations when comparing with respirable cyclone sampling indicates that further improvements are necessary. Positioning of the sampler may be critical and moving the UNC sampler from the chest to e.g. the top of a helmet might be an improvement. Grounding of the sampler in order to avoid static electricity might also be useful. The UNC sampler should continue to be researched for personal sampling, as passive sampling might become a useful alternative to more laborious sampling techniques.

Comparing acute toxicity of gunshot particles, from firing conventional and lead-free ammunition, in pulmonary epithelial cell cultures.

Numerous studies demonstrated that the use of lead (Pb)-containing ammunition is associated with mainly chronic health problems and also is a burden on the environment and wildlife. Recently, a number of reports showed evidence of undesirable acute health effects related to the use of newly developed Pb-free small-caliber ammunition. In this study, particles from leaded and Pb-free ammunition were collected in liquid collection medium, in a highly controlled chamber, while firing a pistol (9 mm) or a rifle (7.62 × 51 mm). The emitted particles were typically smaller than 4 µm, with the great majority in even smaller size ranges, as shown by gravimetrical analysis and a multistage impactor. Chemical analysis revealed significant differences in content and concentration of several metals in the particles. After administration of the liquids to alveolar and bronchial in vitro cell systems, particles were taken up by the cells; the Pb-free particles displayed higher cytotoxicity (EC50 = 2 µg/cm(2)) than particles from Pb ammunition. High correlation factors (>0.9) were found between cell death and content of copper and zinc. Particles from both Pb-containing and Pb-free ammunition were able to induce oxidative stress and the proinflammatory marker interleukin (IL)-8 in both in vitro systems. These results support previous findings that indicate an association between gunshot emissions and metal fume fever. This study demonstrates the usefulness of combining chemical data with biological in vitro responses in assessing acute toxicological effects from emissions from firing both Pb and Pb-free ammunition.

Toxicity and accumulation of trinitrotoluene (TNT) and its metabolites in Atlantic salmon alevins exposed to an industrially polluted water.

A pond in an industrial area in Sweden was selected to study adverse effects on salmon alevins from 2,4,6-trinitrotoluene (TNT)-contaminated water. Chemical screening revealed heavy contamination of TNT and its degradation products, 2-amino-4,6-dinitrotoluene (2-ADNT) and 4-amino-2,6-dinitrotoluene (4-ADNT), ranging from 0.05 to 230 g/kg in the sediment (dry weight) within the water system. Pond water contained 3 mg/L TNT. A dilution series of pond water mixed with tap water revealed increased death frequency in alevins down to fivefold dilution (approximate 0.4 mg TNT/L). Uptake was concentration dependent, reaching 7, 9, and 22 µg/g tissue for TNT, 2-ADNT, and 4-ADNT at the highest test concentration. A time-dependent uptake of TNT and its degradation products was found at a water concentration of 0.08 mg TNT/L. Degradation products of TNT showed a more efficient uptake compared to native TNT, and accumulation of 4-ADNT was more pronounced during the late phase of the 40-d exposure study. Bioconcentration factors (BCF) (0.34, 52, and 134 ml/g for TNT, 2-ADNT, and 4-ADNT, respectively) demonstrated a significant uptake of the metabolite 4-ADNT in alevin tissue. Disturbed physiological conditions and delayed development in alevins were not studied, but may not be excluded even at 125-fold diluted pond water (0.016 mg TNT/L). BCF data indicated that bioaccumulation of TNT metabolites need to be considered in TNT chronic toxicity. Fish species and age differences in the accumulation of TNT metabolites need to be further studied.

Potential exhaled breath biomarkers identified in chlorine-exposed mice.

Exhaled breath (EB) contains various volatile organic compounds (VOCs) that can indicate specific biological or pathological processes in the body. Analytical techniques like gas chromatography-mass spectrometry (GC-MS) can be used to detect and measure these exhaled biomarkers. In this study, the objective was to develop a non-invasive method of EB sampling in animals that were awake, as well as to analyze EB for volatile biomarkers specific for chlorine exposure and/or diagnostic biomarkers for chlorine-induced acute lung injury (ALI). To achieve this, a custom-made sampling device was used to collect EB samples from 19 female Balb/c mice. EB was sampled both pre-exposure (serving as internal control) and 30 min after exposure to chlorine. EB was collected on thermal desorption tubes and subsequently analyzed for VOCs by GC-MS. The following day, the extent of airway injury was assessed in the animals by examining neutrophils in the bronchoalveolar lavage fluid. VOC analysis revealed alterations in the EB biomarker pattern post-chlorine exposure, with eight biomarkers displaying increased levels and six exhibiting decreased levels following exposure. Four chlorinated compounds: trichloromethane, chloroacetone, 1,1-dichloroacetone and dichloroacetonitrile, were increased in chlorine-exposed mice, suggesting their specificity as chlorine EB biomarkers. Furthermore, chlorine-exposed mice displayed a neutrophilic inflammatory response and body weight loss 24 h following exposure. In conclusion, all animals developed an airway inflammation characterized by neutrophil infiltration and a specific EB pattern that could be extracted after chlorine exposure. Monitoring EB samples can readily and non-invasively provide valuable information on biomarkers for diagnosis of chlorine-induced ALI, confirming chlorine exposures.

Broad exposure screening of air pollutants in the occupational environment of Swedish soldiers deployed in Afghanistan.

The main objective of this study was to perform an initial characterization of Swedish soldiers' exposure to air pollutants in Afghanistan and screen for potential health hazards. Stationary monitoring was performed in two military camps, International Security Assistance Force Headquarters in Kabul and Camp Northern Lights in Mazar-e Sharif, at both outdoor and indoor locations. A broad screening including particulate matter (PM10 and PM2.5), polycyclic aromatic hydrocarbons (PAHs), oxygenated PAHs, n-alkanes, nitrogen dioxide (NO2), sulfur dioxide, toxic metals, and volatile organic compounds (VOCs) was performed over 2 weeks in the autumn of 2009. The results were compared to current air quality guidelines. Particulate matter was identified as the main potential health hazard since military exposure guidelines for marginal effects were exceeded outdoors. In addition, especially in Kabul, levels of particle-bound PAHs and oxy-PAHs were high, whereas levels of toxic metals were generally low. Among gaseous pollutants, elevated NO2 levels in Kabul supported combustion as a major contributor to the poor air quality. VOC levels were generally low, but levels of some pollutants exceeded current guidelines. Because of elevated concentrations of particles with a high content of toxic organics, further monitoring and characterization of the occupational environment are warranted.

Exposures to lead during urban combat training.

Lead exposure is still a major concern for occupations that regularly train or work with firearms, such as law enforcement and military personnel. Due to the increasing number of women of fertile age in such professions, there is a strong incentive to monitor lead exposures during firearms training. Personal air sampling was performed during two sessions of a nine-day urban combat training (UCT) course for cadets in the Swedish Armed Forces, one session employing leaded ammunition (leaded scenario) and one session employing unleaded ammunition (unleaded scenario). Blood lead levels (BLLs) were measured before and after the course for 42 cadets and five instructors. During the leaded scenario, the instructors' airborne exposure (geometric mean, GM, 72.0 µg/m3) was higher than that of cadets (GM 42.9 µg/m3). During the unleaded scenario, airborne concentrations were similar for instructors and cadets and considerably lower than during the leaded scenario (GM 2.9 µg/m3). Despite comparably low external lead exposures during the course, we saw a statistically significant increase in systemic exposure for cadets (BLL GM increased from 1.09 to 1.71 µg/dL, p < 0.001). For the five instructors, notable differences were seen depending on task. The largest increase was seen for the two instructors performing close supervision during the leaded scenario (BLL GM increased from 2.41 µg/dL to 4.83 µg/dL). For the remaining three instructors the BLLs were unchanged (BLL GMs were 1.25 µg/dL before the course and 1.26 µg/dL after). None of the participants exceeded the applicable biological exposure limits, but extrapolating our findings shows that instructors in the leaded scenario may reach levels around 10 µg/dL after a year of repeated exposures. We conclude that comparably low airborne concentrations can contribute to the body burden of lead and that additional measures to reduce exposure are warranted, particularly for instructors.

Development of air sampling strategies for monitoring common air pollutants in a mission area at Camp Victoria in Kosovo--stationary vs. personal monitoring.

It can be problematic to collect representative samples in the occupational environment of deployed soldiers using personal samplers. In this study, several air sampling strategies were examined to identify the most efficient method for collecting air samples that were representative of the soldiers' exposure profiles at the Swedish KFOR Camp Victoria outside Pristina, Kosovo. Stationary monitoring was performed during two 5-day sampling campaigns, one in summer and one in winter. The acquired data were related to measurements obtained by personal monitoring of three and four subgroups, respectively. Patrolling soldiers, mechanics, and indoor workers were selected to represent groups with different exposure profiles, and the particles, metals associated with particles, nitrogen dioxide, sulfur dioxide, polycyclic aromatic hydrocarbons, aldehydes, and volatile organic compounds that they were exposed to were measured. Generally, low concentrations of the analytes were found in both sampling periods, but the variability was greater in the winter campaign. Samples collected by stationary samplers captured most of the variation in the personnel's exposure, according to principal component analysis (PCA). However, the results also indicate that personal exposure to most potential pollutants would be underestimated if a single outdoor station was used to monitor them. Nevertheless, combined data from stations located outdoors and in relevant microenvironments (workshop, office, and guard station) provided substantially better representation. Thus, it may be possible to obtain monitoring data without using personal samplers in these inherently problematic situations.

Impact of Fire Suit Ensembles on Firefighter PAH Exposures as Assessed by Skin Deposition and Urinary Biomarkers.

Over the past 10 years, a number of safety measures for reducing firefighters' exposure to combustion particles have been introduced in Sweden. The most important measure was the reduction in the time firefighters wear suits and handle contaminated equipment after turn-outs involving smoke diving. This study was divided into two parts, those being to investigate the level of protection obtained by multiple garment layers and to assess exposure during a standardized smoke diving exercise. First, realistic work protection factors (WPFs) were calculated by comparing air concentrations of the full suite of gaseous and particle-bound polycyclic aromatic hydrocarbons (PAHs) inside and outside structural ensembles, including jacket and thick base layer, during a tough fire extinguishing exercise using wood as the fuel. Second, during a standardized smoke diving exercise, exposure was assessed by measuring PAH skin deposition and levels of eight urinary PAH metabolites in 20 volunteer student firefighters before and after the exercise. The average WPF for the sum of 22 PAHs was 146 ± 33 suggesting a relatively high protective capacity but also indicating a substantial enrichment of contaminants with a risk of prolonged dermal exposure. Accordingly, in the second exercise, the median levels of skin-deposited Σ14-PAHs and urinary 1-hydroxypyrene significantly increased 5-fold (21 to 99 ng/wipe) and 8-fold (0.14 to 1.1 µmol mol-1 creatinine), respectively, post exposure. Among the PAH metabolites investigated, 1-hydroxypyrene proved to be the most useful indicator of exposure, with significantly elevated urinary levels at both 6 h and 20 h after the exercise and with the strongest correlation to dermal exposure. Metabolites from two-ring and three-ring PAHs were eliminated faster while levels of 3-hydroxy-benzo[a]pyrene did not meet the detection criteria. The results from correlation studies indicated that dermal uptake was a major route of exposure in accordance with previous findings. To summarize, this study shows that some of the newly adopted protective measures were correctly implemented, and should continue to be followed and be more widely adopted.

Improving the UNC Passive Aerosol Sampler Model Based on Comparison with Commonly Used Aerosol Sampling Methods.

Objectives: In an occupational environment, passive sampling could be an alternative to active sampling with pumps for sampling of dust. One passive sampler is the University of North Carolina passive aerosol sampler (UNC sampler). It is often analysed by microscopic imaging. Promising results have been shown for particles above 2.5 µm, but indicate large underestimations for PM2.5. The aim of this study was to evaluate, and possibly improve, the UNC sampler for stationary sampling in a working environment. Methods: Sampling was carried out at 8-h intervals during 24 h in four locations in an open pit mine with UNC samplers, respirable cyclones, PM10 and PM2.5 impactors, and an aerodynamic particle sizer (APS). The wind was minimal. For quantification, two modifications of the UNC sampler analysis model, UNC sampler with hybrid model and UNC sampler with area factor, were compared with the original one, UNC sampler with mesh factor derived from wind tunnel experiments. The effect of increased resolution for the microscopic imaging was examined. Results: Use of the area factor and a higher resolution eliminated the underestimation for PM10 and PM2.5. The model with area factor had the overall lowest deviation versus the impactor and the cyclone. The intraclass correlation (ICC) showed that the UNC sampler had a higher precision and better ability to distinguish between different exposure levels compared to the cyclone (ICC: 0.51 versus 0.24), but lower precision compared to the impactor (PM10: 0.79 versus 0.99; PM2.5: 0.30 versus 0.45). The particle size distributions as calculated from the different UNC sampler analysis models were visually compared with the distributions determined by APS. The distributions were obviously different when the UNC sampler with mesh factor was used but came to a reasonable agreement when the area factor was used. Conclusions: High resolution combined with a factor based on area only, results in no underestimation of small particles compared to impactors and cyclones and a better agreement with the APS's particle size distributions. The UNC sampler had lower precision than the impactors, but higher than the respirable cyclone. The UNC sampler with area factor could be used for PM2.5, PM10 and respirable fraction measurements in this working environment without wind.

A Pilot Study: The UNC Passive Aerosol Sampler in a Working Environment.

OBJECTIVES: Dust is generally sampled on a filter using air pumps, but passive sampling could be a cost-effective alternative. One promising passive sampler is the University of North Carolina passive aerosol sampler (UNC sampler). The aim of this study is to characterize and compare the UNC sampler's performance with PM10 and PM2.5 impactors in a working environment. METHODS: Area sampling was carried out at different mining locations using UNC samplers in parallel with PM2.5 and PM10 impactors. Two different collection surfaces, polycarbonate (PC) and carbon tabs (CT), were employed for the UNC sampling. Sampling was carried out for 4-25 hours. RESULTS: The UNC samplers underestimated the concentrations compared to PM10 and PM2.5 impactor data. At the location with the highest aerosol concentration, the time-averaged mean of PC showed 24% and CT 35% of the impactor result for PM2.5. For PM10, it was 39% with PC and 58% with CT. Sample blank values differed between PC and CT. For PM2.5, PC blank values were ~7 times higher than those of CT, but only 1.8 times higher for PM10. The blank variations were larger for PC than for CT. CONCLUSIONS: Particle mass concentrations appear to be underestimated by the UNC sampler compared to impactors, more so for PM2.5 than for PM10. CT may be preferred as a collection surface because the blank values were lower and less variable than for PC. Future validations in the working environment should include respirable dust sampling.

Hand-Held Femtogram Detection of Hazardous Picric Acid with Hydrophobic Ag Nanopillar SERS Substrates and Mechanism of Elasto-Capillarity.

Picric acid (PA) is a severe environmental and security risk due to its unstable, toxic, and explosive properties. It is also challenging to detect in trace amounts and in situ because of its highly acidic and anionic character. Here, we assess sensing of PA under nonlaboratory conditions using surface-enhanced Raman scattering (SERS) silver nanopillar substrates and hand-held Raman spectroscopy equipment. The advancing elasto-capillarity effects are explained by molecular dynamics simulations. We obtain a SERS PA detection limit on the order of 20 ppt, corresponding attomole amounts, which together with the simple analysis methodology demonstrates that the presented approach is highly competitive for ultrasensitive analysis in the field.

Field evaluation and calibration of a small axial passive air sampler for gaseous and particle bound polycyclic aromatic hydrocarbons (PAHs) and oxygenated PAHs.

Polycyclic aromatic hydrocarbons (PAHs) and their oxygenated analogues (OPAHs) are ubiquitous air pollutants known to cause adverse health effects. PAH air levels are commonly monitored by active sampling but passive sampling has become popular because of its lower cost and simplicity, which facilitate long-term sampling and increased spatial coverage. However, passive samplers are less suitable for short-term sampling and are in general less accurate than active samplers because they require reliable sampling rate (Rs) measurements for individual analytes under diverse environmental conditions. In this study a small passive sampler designed to sample both particle-bound and gaseous compounds was evaluated and calibrated for PAHs and OPAHs in a traffic environment by co-deployment with active samplers for two weeks. Despite the relatively low average air concentrations of PM10 (20 µg/m(3)), PM2.5 (5 µg/m(3)), total PAHs (4.2 ng/m(3)), and OPAHs (2.3 ng/m(3)) at the site, detectable quantities (on average 24 times above blank values) of the full range of PAHs and OPAHs were captured, with low variability (average RSD of 16%). This was accomplished by using a Tenax(®) TA-modified glass fiber substrate that is compatible with highly sensitive thermal desorption GC-MS analysis, which made it possible to achieve detection limits per sample in the pg range. Experiments with inverted samplers revealed that the relative contribution of gravitational settling to the sampling of particles carrying PAHs and OPAHs was around 3.5 times larger than other deposition mechanisms. Average Rs values for individual OPAHs and PAHs were 0.046 ± 0.03 m(3)/day and 0.12 ± 0.07 m(3)/day, respectively, with no appreciable difference between the values for particle-associated and gaseous compounds. Furthermore, the Rs values were competitive with other currently used passive samplers if normalized for substrate area. Overall, the new sampler's performance, simplicity and ability to generate relatively time-resolved data make it a promising candidate for diverse SVOC monitoring studies.

Air-sea gas exchange of HCHs and PCBs and enantiomers of alpha-HCH in the Kattegat Sea region.

Concentrations and air-water gas exchange of polychlorinated biphenyls (PCBs) and hexachlorocyclohexanes (HCHs) were determined in nine paired air and water samples. The samples were collected monthly in the Kattegat Sea between December 1998 and November 1999. Average fugacity and flux values indicated that PCBs were oversaturated in the water, while HCHs were net deposited. Variations were large over the year, especially during spring and summer. Air parcel back trajectories suggested that air concentrations over the Kattegat Sea are largely dependent of air mass origin. Seasonal trends were detected for airborne HCHs and for PCBs in water. The air and water enantiomeric compositions of alpha-HCH indicated that a larger portion of alpha-HCH in air originated from the underlying water during summer than during winter.

Oxidative stress and cytokine expression in respiratory epithelial cells exposed to well-characterized aerosols from Kabul, Afghanistan.

In this study aerosol samples collected in an Asian mega-city (Kabul, Afghanistan) were compared to PM samples collected in a European location with traffic (Umeå, Sweden) and a reference urban dust material (SRM 1649b). The toxicity of each sample towards normal human bronchial epithelial (NHBE) cells and a human bronchial epithelial cell line (BEAS-2B) was tested along with their ability to induce reactive oxygen species (ROS) formation and inflammatory responses. The extracts' morphology and elemental composition was studied by SEM-EDXRF, and filter samples were analyzed for metals and organic compounds. The PM from Kabul contained a larger fraction of fine particles, 19 times more polyaromatic hydrocarbons (PAH) and 37 times more oxygenated PAH (oxy-PAH) compared to samples from Umeå. The PM-samples from Kabul and the reference material (SRM 1649b) induced significantly stronger oxidative stress responses than the samples from Umeå. Furthermore, samples collected in Kabul induced significantly higher secretion of the cytokines IL-6, IL-8 and GM-CSF while SRM1649b induced a cytokine pattern more similar to samples collected in Umeå. Several properties of the particles could potentially explain these differences, including differences in their size distribution and contents of PAH and oxy-PAH, possibly in combination with their relative transition metal contents.

Polychlorinated biphenyls (PCB), thyroid hormones and cytokines in construction workers removing old elastic sealants.

OBJECTIVES: To estimate the internal PCB level in Swedish workers specialised in PCB abatement in buildings and to measure possible effects of PCB on thyroid function and aspects of the immune system. METHODS: Thirty six of 40 eligible workers (90%) removing old elastic sealants containing PCB and 33 control construction workers provided blood samples for determination of 19 PCB congeners and some other organochlorine compounds (hexachlorobenzene and p,p'-DDE), thyroid function hormones and a set of cytokines. The PCB exposed group was reinvestigated after 10 months for a trend assessment. RESULTS: The sum of 19 PCB congeners in blood plasma from the occupationally PCB-exposed group was twice the level in the controls (geometric mean 580 vs. 260 ng/g lipid; P < 0.001), and there was also some difference in p,p'-DDE between the groups while the lipid-adjusted hexachlorobenzene levels were of the same magnitude. No statistically significant increase in overall PCB levels was observed in the abatement workers at follow-up and some congeners even declined. Thyroid function was not associated with PCB exposure at the current levels and this applied also to the cytokines investigated. CONCLUSIONS: Swedish workers removing old elastic sealants with PCB have a higher internal PCB load than unexposed colleague construction workers, tentatively secondary to historical exposure. A system of protective measures seemed to be efficient since no further increase was noted after a longish period of additional exposure. There was no evidence of thyroid function or immune system involvement, as expressed by a set of cytokines, at the low PCB levels recorded.