Reconfigurable ultra-broadband mode converter based on a two-mode fiber with pressure-loaded phase-shifted long-period alloyed waveguide grating.

We present a reconfigurable ultra-broadband mode converter, which consists of a two-mode fiber (TMF) and pressure-loaded phase-shifted long-period alloyed waveguide grating. We design and fabricate the long-period alloyed waveguide gratings (LPAWG) with SU-8, chromium, and titanium via the photo-lithography and electric beam evaporation technique. With the help of the pressure loaded or released from the LPAWG onto the TMF, the device can realize reconfigurable mode conversion between the LP01 mode and the LP11 mode in the TMF, which is weak sensitive to the state of polarization. The mode conversion efficiency larger than 10 dB can be achieved with operation wavelength range of about 105 nm, which ranges from 1501.9 nm to 1606.7 nm. The proposed device can be further used in the large bandwidth mode division multiplexing (MDM) transmission and optical fiber sensing system based on few-mode fibers.

Three-dimensional mode multiplexer based on adiabatic-tapered waveguides forming vertical directional couplers over C + L band and beyond.

We present a mode multiplexer based on vertical directional couplers that are formed by adiabatic-tapered waveguides. We design and fabricate the device via the micro-fabrication processing to (de)multiplex the E11, E21, and E12 modes from the few-mode bus waveguide. Our experimental device shows a coupling ratio higher than 98.6% and 97.0% for the E21 and E12 modes, respectively, over the C + L band and beyond. The modal cross talk of this device can be lower than -17.1 dB, -18.4 dB, and -15.1 dB caused by the unintended E11, E21, and E12 modes, respectively. This mode multiplexer can work over a broader wavelength range with weak polarization sensitivity, which could be used in the mode-division-multiplexing systems where mode (de)multiplexing is required in the expanded communication wavelength window other than the C-band.

All-optical light manipulation based on graphene-embedded side-polished fiber.

We present a study of all-optical light manipulation arising in a graphene-embedded side-polished fiber (SPF) with a Norland Optical Adhesives (NOA)-coated structure. With the help of the Pauli blocking effect, such an all-fiber device serves to manage the loss of transverse-electric-polarized light when the control light and the signal light are polarized along the direction parallel to the graphene surface. The insertion loss of this device can be effectively reduced with the NOA coating. An enhanced interaction between the graphene and the propagated light can be achieved via the strong evanescent field of the SPF and longer interaction length. This results in effective all-optical manipulation of light with a modulation depth of 10.4 dB (or modulation efficiency of ∼91%) and a modulation slope of ∼1.3, where the required control power is only about 14 dBm. The device has broadband operation wavelength. The insertion loss for both the signal light and the control light are only about 0.6 dB. The experimental results are well-fitting with the simulation study. Such an all-fiber device has the potential for all-optical signal processing.

Ring core few-mode fiber sensor for curvature measurement.

An all-fiber Mach-Zehnder interferometer (MZI) using ring core few-mode fiber (RC-FMF) for curvature sensing is proposed and experimentally demonstrated. The MZI was fabricated by splicing a segment of RC-FMF between two pieces of single-mode fiber (SMF). With the benefit of a RC of the central axis of the RC-FMF, the sensor is more sensitive to curvature compared to other fiber sensors based on ordinary SMF or FMF. Curvature measurement can be achieved by monitoring the wavelength shift of interference dips. Experimental results have shown that the sensitivity of curvature sensing can reach up to -4.370nm/m-1, within the range of 1.199-1.549m-1. Also, the temperature sensing characteristics of the sensor are measured, and the maximum temperature sensitivity is 57.6 pm/°C, ranging from 25°C to 45°C. The proposed MZI sensor has excellent potential for curvature measurement of building structural health monitoring, bridge engineering, and more.

Low Power Consuming Mode Switch Based on Hybrid-Core Vertical Directional Couplers with Graphene Electrode-Embedded Polymer Waveguides.

We propose a mode switch based on hybrid-core vertical directional couplers with an embedded graphene electrode to realize the switching function with low power consumption. We designed the device with Norland Optical Adhesive (NOA) material as the guide wave cores and epoxy polymer material as cladding to achieve a thermo-optic switching for the E11, E21 and E12 modes, where monolayer graphene served as electrode heaters. The device, with a length of 21 mm, had extinction ratios (ERs) of 20.5 dB, 10.4 dB and 15.7 dB for the E21, E12 and E11 modes, respectively, over the C-band. The power consumptions of three electric heaters were reduced to only 3.19 mW, 3.09 mW and 2.97 mW, respectively, and the response times were less than 495 µs, 486 µs and 498 µs. Additionally, we applied such a device into a mode division multiplexing (MDM) transmission system to achieve an application of gain equalization of few-mode amplification among guided modes. The differential modal gain (DMG) could be optimized from 5.39 dB to 0.92 dB over the C-band, together with the characteristic of polarization insensitivity. The proposed mode switch can be further developed to switch or manipulate the attenuation of the arbitrary guided mode arising in the few-mode waveguide.