Evaluating the pharmacokinetics of beclometasone dipropionate/formoterol fumarate/glycopyrronium bromide delivered via pressurised metered-dose inhaler using a low global warming potential propellant.

INTRODUCTION: Use of propellants with high global warming potential (such as HFA-134a) for pressurised metered-dose inhalers (pMDIs) is being phased down. Switching to dry-powder inhalers may not be clinically feasible for all patients; an alternative is reformulation using propellants with low global warming potential. The combination of beclometasone dipropionate/formoterol fumarate/glycopyrronium bromide (BDP/FF/GB) is available for asthma or chronic obstructive pulmonary disease via pMDI using HFA-134a as propellant. This is being reformulated using the low global warming potential propellant HFA-152a. This manuscript reports three studies comparing BDP/FF/GB pharmacokinetics delivered via pMDI using HFA-152a vs HFA-134a. METHODS: The studies were four-way crossover, single-dose, randomised, double-blind, in healthy volunteers. In Studies 1 and 2, subjects inhaled four puffs of BDP/FF/GB (Study 1: 100/6/12.5 µg [medium-strength BDP]; Study 2: 200/6/12.5 µg [high-strength]), ingesting activated charcoal in two of the periods (once per propellant). In Study 3, subjects inhaled medium- and high-strength BDP/FF/GB using a spacer. All three studies compared HFA-152a vs HFA-134a in terms of lung availability and total systemic exposure of beclometasone-17-monopropionate (B17MP; active metabolite of BDP), BDP, formoterol and GB. Bioequivalence was concluded if the 90 % confidence intervals (CIs) of the ratios between formulations of the geometric mean maximum plasma concentration (Cmax) and area under the plasma concentration-time curve between time zero and the last quantifiable timepoint (AUC0-t) for the analytes were between 80 and 125 %. RESULTS: In Studies 1 and 2, systemic exposure bioequivalence (i.e., comparisons without charcoal block) was demonstrated, except for GB Cmax in Study 2 (upper 90 % CI 125.11 %). For lung availability (i.e., comparisons with charcoal block), B17MP and formoterol demonstrated bioequivalence in both studies, as did BDP in Study 2; in Study 1, BDP upper CIs were 126.96 % for Cmax and 127.34 % for AUC0-t). In Study 1, GB AUC0-t lower CI was 74.54 %; in Study 2 upper limits were 135.64 % for Cmax and 129.12 % for AUC0-t. In Study 3, the bioequivalence criteria were met for BDP, B17MP and formoterol with both BDP/FF/GB strengths, and were met for GB AUC0-t, although not for Cmax. Both formulations were similarly well tolerated in all three studies. CONCLUSIONS: Overall, while formal bioequivalence cannot be concluded for all analytes, these data suggest therapeutic equivalence of the new formulation with the existing BDP/FF/GB pMDI formulation, therefore supporting reformulation using a propellant with low global warming potential.

Repurposing Melt Degradation for the Evaluation of Mixed Amorphous-Crystalline Blends.

Medicine regulators require the melting points for crystalline drugs, as they are a test for chemical and physical quality. Many drugs, especially salt-forms, suffer concomitant degradation during melting; thus, it would be useful to know if the endotherm associated with melt degradation may be used for characterising the crystallinity of a powder blend. Therefore, the aim of this study was to investigate whether melt-degradation transitions can detect amorphous content in a blend of crystalline and amorphous salbutamol sulphate. Salbutamol sulphate was rendered amorphous by freeze and spray-drying and blended with crystalline drug, forming standards with a range of amorphous content. Crystalline salbutamol sulphate was observed to have a melt-degradation onset of 198.2±0.2°C, while anhydrous amorphous salbutamol sulphate prepared by either method showed similar glass transition temperatures of 119.4±0.7°C combined. Without the energy barrier provided by the ordered crystal lattice, the degradation endotherm for amorphous salbutamol sulphate occurred 50°C below the melting point, with an onset of 143.6±0.2°C. The enthalpies for this degradation transition showed no significant difference between freeze- and spray-dried samples (p>0.05). Distinct from convention, partial integration of the crystalline melt-degradation endotherm was applied to the region 193-221°C which had no contribution from the degradation of amorphous salbutamol sulphate. The linear correlation of these partial areas with amorphous content, R2=0.994, yielded limits of detection and quantification of 0.13% and 0.44% respectively, independent of drying technique. Melt-degradation transitions may be re-purposed for the measurement of amorphous content in powder blends, and they have potential for evaluating disorder more generally.

Revefenacin Absorption, Metabolism, and Excretion in Healthy Subjects and Pharmacological Activity of Its Major Metabolite.

Revefenacin inhalation solution is an anticholinergic indicated for the maintenance treatment of patients with chronic obstructive pulmonary disease. Mass balance, pharmacokinetics, and metabolism of revefenacin were evaluated after intravenous and oral administration of [14C]-revefenacin in healthy subjects. Pharmacological activity of the major revefenacin metabolite was also assessed. Adult males (n = 9) received 20 µg intravenously of approximately 1 µCi [14C]-revefenacin and/or a single 200-µg oral solution of approximately 10 µCi [14C]-revefenacin. Mean recovery of radioactive material was 81.4% after intravenous administration (54.4% in feces; 27.1% in urine) and 92.7% after oral dosing (88.0% in feces, 4.7% in urine). Mean absolute bioavailability of oral revefenacin was low (2.8%). Intact revefenacin accounted for approximately 52.1% and 13.1% of the total radioactivity in plasma after intravenous and oral administration, respectively. Two main circulating metabolites were observed in plasma. After an intravenous dose, a hydrolysis product, THRX-195518 (M2) was observed that circulated in plasma at 14.3% of total radioactivity. After an oral dose, both THRX-195518 and THRX-697795 (M10, N-dealkylation and reduction of the parent compound) were observed at 12.5% of total circulating radioactivity. THRX-195518 was the major metabolite excreted in feces and comprised 18.8% and 9.4% of the administered intravenous and oral dose, respectively. The major metabolic pathway for revefenacin was hydrolysis to THRX-195518. In vitro pharmacological evaluation of THRX-195518 indicated that it had a 10-fold lower binding affinity for the M3 receptor relative to revefenacin. Receptor occupancy analysis suggested that THRX-195518 has minimal contribution to systemic pharmacology relative to revefenacin after inhaled administration. SIGNIFICANCE STATEMENT: The major metabolic pathway for revefenacin was hydrolysis to the metabolite THRX-195518 (M2), and both revefenacin and THRX-195518 underwent hepatic-biliary and fecal elimination after oral or intravenous administration with negligible renal excretion. Pharmacological evaluation of THRX-195518 indicated that it had a 10-fold lower binding affinity for the M3 muscarinic receptor relative to revefenacin and that THRX-195518 has minimal contribution to systemic pharmacology after inhaled administration.

Theophylline Acetaldehyde as the Initial Product in Doxophylline Metabolism in Human Liver.

Doxophylline (DOXO) and theophylline are widely used as bronchodilators for treating asthma and chronic obstructive pulmonary disease, and DOXO has a better safety profile than theophylline. How DOXO's metabolism and disposition affect its antiasthmatic efficacy and safety remains to be explored. In this study, the metabolites of DOXO were characterized. A total of nine metabolites of DOXO were identified in vitro using liver microsomes from human and four other animal species. Among them, six metabolites were reported for the first time. The top three metabolites were theophylline acetaldehyde (M1), theophylline-7-acetic acid (M2), and etophylline (M4). A comparative analysis of DOXO metabolism in human using liver microsomes, S9 fraction, and plasma samples demonstrated the following: 1) The metabolism of DOXO began with a cytochrome P450 (P450)-mediated, rate-limiting step at the C ring and produced M1, the most abundant metabolite in human liver microsomes. However, in human plasma, the M1 production was rather low. 2) M1 was further converted to M2 and M4, the end products of DOXO metabolism in vivo, by non-P450 dismutase in the cytosol. This dismutation process also relied on the ratio of NADP+/NADPH in the cell. These findings for the first time elucidated the metabolic sites and routes of DOXO metabolism in human. SIGNIFICANCE STATEMENT: We systematically characterized doxophylline metabolism using in vitro and in vivo assays. Our findings evolved the understandings of metabolic sites and pathways for methylxanthine derivatives with the aldehyde functional group.

Navafenterol (AZD8871) in healthy volunteers: safety, tolerability and pharmacokinetics of multiple ascending doses of this novel inhaled, long-acting, dual-pharmacology bronchodilator, in two phase I, randomised, single-blind, placebo-controlled studies.

BACKGROUND: Navafenterol (AZD8871) is a novel, long-acting, dual-pharmacology (muscarinic receptor antagonist and ß2-adrenoceptor agonist) molecule in development for chronic obstructive pulmonary disease and asthma. METHODS: These two phase I, randomised, single-blind, multiple-ascending-dose studies evaluated inhaled navafenterol and placebo (3:1 ratio) in healthy, male, non-Japanese (study A; NCT02814656) and Japanese (study B; NCT03159442) volunteers. In each study, volunteers were dosed in three cohorts, allowing gradual dose escalation from 300 µg to 600 µg to 900 µg. The primary objective was to investigate the safety and tolerability of navafenterol at steady state. Pharmacokinetics were also assessed. RESULTS: Twenty-four volunteers completed each study (navafenterol, n = 6; placebo, n = 2 in each cohort). There were no deaths, serious adverse events (AEs) or treatment-emergent AEs (TEAEs) leading to discontinuation of navafenterol. The most frequent TEAEs were vessel puncture-site bruise (placebo, n = 2; navafenterol 900 µg; n = 3) in study A and diarrhoea (placebo, n = 1; navafenterol 300 µg, n = 2; navafenterol 900 µg, n = 3) in study B. No dose-response relationship was observed for TEAEs. There was a dose-dependent increase in mean heart rate on day 16 in both studies. The pharmacokinetics of navafenterol were similar between non-Japanese and Japanese volunteers. CONCLUSIONS: Multiple ascending doses of navafenterol were well-tolerated and the safety and pharmacokinetics of navafenterol were similar in non-Japanese and Japanese volunteers. The findings support navafenterol clinical development. TRIAL REGISTRATION: ClinicalTrials.gov ; Nos.: NCT02814656 and NCT03159442; URL: www.clinicaltrials.gov .

Navafenterol (AZD8871) in patients with COPD: a randomized, double-blind, phase I study evaluating safety and pharmacodynamics of single doses of this novel, inhaled, long-acting, dual-pharmacology bronchodilator.

BACKGROUND: Navafenterol (AZD8871) is a dual-pharmacology muscarinic antagonist ß2-agonist (MABA) molecule in development for the treatment of chronic obstructive pulmonary disease (COPD). The pharmacodynamics, safety and tolerability of single doses of navafenterol were investigated in patients with moderate to severe COPD. METHODS: This was a randomized, five-way complete cross-over study. Patients received single doses of navafenterol 400 µg, navafenterol 1800 µg and placebo (all double-blind) and indacaterol 150 µg and tiotropium 18 µg (both open-label active comparators). The primary pharmacodynamic endpoint was change from baseline in trough forced expiratory volume in 1 s (FEV1) on day 2. Safety and tolerability were monitored throughout. RESULTS: Thirty-eight patients were randomized and 28 (73.7%) completed the study. Navafenterol 400 µg and 1800 µg demonstrated statistically significant improvements vs placebo in change from baseline in trough FEV1 (least squares mean [95% confidence interval]: 0.111 [0.059, 0.163] L and 0.210 [0.156, 0.264] L, respectively, both P < .0001). The changes were significantly greater with navafenterol 1800 µg vs the active comparators (least squares mean treatment difference: 0.065-0.069 L, both P < .05). The frequency of treatment-emergent adverse events was similar for placebo and the active comparators (range 34.4-37.5%), slightly higher for navafenterol 400 µg (52.9%), and lowest for navafenterol 1800 µg (22.6%). CONCLUSIONS: Both doses of navafenterol demonstrated sustained bronchodilation over 24 h. Navafenterol was well tolerated and no safety concerns were raised. TRIAL REGISTRY: ClinicalTrials.gov ; No.: NCT02573155 ; URL: www.clinicaltrials.gov . Registered 9th October, 2015.

Navafenterol (AZD8871) in patients with mild asthma: a randomised placebo-controlled phase I study evaluating the safety, tolerability, pharmacokinetics, and pharmacodynamics of single ascending doses of this novel inhaled long-acting dual-pharmacology bronchodilator.

BACKGROUND: Navafenterol (AZD8871) is an inhaled long-acting dual-pharmacology muscarinic antagonist/ß2-adrenoceptor agonist (MABA) in development for the treatment of obstructive airways diseases. The safety, tolerability, pharmacodynamics, and pharmacokinetics of navafenterol were investigated in patients with mild asthma. METHODS: This was a randomised, single-blind, placebo-controlled, single-ascending-dose study. Patients were randomly assigned to one of two cohorts which evaluated escalating doses of navafenterol (50-2100 µg) in an alternating manner over three treatment periods. The primary pharmacodynamic endpoint was the change from pre-dose baseline in trough forced expiratory volume in 1 s (FEV1) for each treatment period. RESULTS: Sixteen patients were randomised; 15 completed treatment. Data from all 16 patients were analysed. The maximum tolerated dose was not identified, and all doses of navafenterol were well tolerated. The most frequently reported treatment-emergent adverse events (TEAEs) were headache (n = 10, 62.5%) and nasopharyngitis (n = 7, 43.8%). No TEAEs were serious, fatal, or led to discontinuation, and no dose dependency was identified. Navafenterol demonstrated a dose-ordered bronchodilatory response with a rapid onset of action (within 5 min post-dose). Doses ≥200 µg resulted in improvements in trough FEV1 (mean change from baseline range 0.186-0.463 L) with sustained bronchodilation for 24-36 h. Plasma concentrations increased in a dose-proportional manner, peaking ~ 1 h post-dose, with a derived terminal elimination half-life of 15.96-23.10 h. CONCLUSIONS: In this study navafenterol was generally well tolerated with a rapid onset of action which was sustained over 36 h. TRIAL REGISTRATION: ClinicalTrials.gov; No.: NCT02573155.

Pharmacokinetics of budesonide/glycopyrrolate/formoterol fumarate metered dose inhaler formulated using co-suspension delivery technology after single and chronic dosing in patients with COPD.

BACKGROUND: Budesonide/glycopyrrolate/formoterol fumarate metered dose inhaler (BGF MDI), formulated using co-suspension delivery technology, is a triple fixed-dose combination in late-stage clinical development for chronic obstructive pulmonary disease (COPD). METHODS: We conducted two studies to characterize the pharmacokinetic (PK) profile of BGF MDI in patients with COPD: (i) a phase I, open-label, single and chronic (7-day) dosing study (NCT03250182) with one treatment arm (BGF MDI 320/18/9.6 µg); and (ii) a PK sub-study of KRONOS (NCT02497001), a phase III, randomized, double-blind study in which patients received 24 weeks' treatment with BGF MDI 320/18/9.6 µg, glycopyrrolate/formoterol fumarate (GFF) MDI 18/9.6 µg, budesonide/formoterol fumarate (BFF) MDI 320/9.6 µg, or budesonide/formoterol fumarate dry powder inhaler (BUD/FORM DPI) 320/9 µg. PK parameters in both studies included maximum observed plasma concentration (Cmax) and area under the plasma concentration-time curve from 0 to 12h (AUC0-12). RESULTS: In the phase I PK study (30 patients), budesonide and glycopyrronium Cmax were comparable after single and chronic dosing of BGF MDI (accumulation ratio [RAC] 95% and 107%, respectively) whereas Cmax for formoterol was slightly higher after chronic dosing (RAC 116%). AUC0-12 for budesonide, glycopyrronium, and formoterol were higher following chronic versus single dosing, with an RAC of 126%, 179%, and 143%, respectively. After 7 days' dosing, AUC0-12 and Cmax for all three components of BGF MDI were similar to those in the KRONOS PK sub-study (202 patients) at Week 24. In the latter sub-study, Cmax and AUC0-12 at Week 24 were generally comparable across treatments for budesonide (geometric mean ratios [GMR] of 96%-109% for BGF MDI vs BFF MDI or BUD/FORM DPI), glycopyrronium (GMR of 88%-100% for BGF MDI vs GFF MDI), and formoterol (GMR of 80%-113% for BGF MDI vs GFF MDI or BFF MDI). CONCLUSIONS: Steady-state PK parameters of budesonide, glycopyrronium, and formoterol were similar after 7 days' dosing in the phase I PK study and after 24 weeks in the KRONOS PK sub-study. Systemic exposure to budesonide, glycopyrronium, and formoterol was generally comparable across treatments in the KRONOS PK sub-study, suggesting no meaningful drug-drug or within-formulation PK interactions.

Combined in Vitro-in Silico Approach to Predict Deposition and Pharmacokinetics of Budesonide Dry Powder Inhalers.

PURPOSE: A combined in vitro - in silico methodology was designed to estimate pharmacokinetics of budesonide delivered via dry powder inhaler. METHODS: Particle size distributions from three budesonide DPIs, measured with a Next Generation Impactor and Alberta Idealized Throat, were input into a lung deposition model to predict regional deposition. Subsequent systemic exposure was estimated using a pharmacokinetic model that incorporated Nernst-Brunner dissolution in the conducting airways to predict the net influence of dissolution, mucociliary clearance, and absorption. RESULTS: DPIs demonstrated significant in vitro differences in deposition, resulting in large differences in simulated regional deposition in the central conducting airways and the alveolar region. Similar but low deposition in the small conducting airways was observed with each DPI. Pharmacokinetic predictions showed good agreement with in vivo data from the literature. Peak systemic concentration was tied primarily to the alveolar dose, while the area under the curve was more dependent on the total lung dose. Tracheobronchial deposition was poorly correlated with pharmacokinetic data. CONCLUSIONS: Combination of realistic in vitro experiments, lung deposition modeling, and pharmacokinetic modeling was shown to provide reasonable estimation of in vivo systemic exposure from DPIs. Such combined approaches are useful in the development of orally inhaled drug products.

Advancement of a Positive-Pressure Dry Powder Inhaler for Children: Use of a Vertical Aerosolization Chamber and Three-Dimensional Rod Array Interface.

PURPOSE: Available dry powder inhalers (DPIs) have very poor lung delivery efficiencies in children. The objective of this study was to advance and experimentally test a positive-pressure air-jet DPI for children based on the use of a vertical aerosolization chamber and new patient interfaces that contain a three-dimensional (3D) rod array structure. METHODS: Aerosolization performance of different air-jet DPI designs was first evaluated based on a 10 mg powder fill mass of a spray-dried excipient enhanced growth (EEG) formulation. Devices were actuated with positive pressure using flow rate (10-20 L/min) and inhaled volume (750 ml) conditions consistent with a 5-year-old child. Devices with best performance were connected to different mouthpiece designs to determine the effect on aerosolization and tested for aerosol penetration through a realistic pediatric in vitro mouth-throat model. RESULTS: Use of the new vertical aerosolization chamber resulted in high quality aerosol formation. Inclusion of a 3D rod array structure in the mouthpiece further reduced aerosol size by approximately 20% compared to conditions without a rod array, and effectively dissipated the turbulent jet leaving the device. Best case device and mouthpiece combinations produced < 2% mouth-throat depositional loss and > 70% lung delivery efficiency based on loaded dose. CONCLUSIONS: In conclusion, use of a 3D rod array in the MP of a positive-pressure air-jet DPI was found to reduce aerosol size by 20%, not significantly increase MP depositional loss, reduce mouth-throat deposition by 6.4-fold and enable lung delivery efficiency as high as 73.4% of loaded dose based on pediatric test conditions.

Particle size and gastrointestinal absorption influence tiotropium pharmacokinetics: a pilot bioequivalence study of PUR0200 and Spiriva HandiHaler.

AIMS: Plasma pharmacokinetics permit the assessment of efficacy and safety of inhaled drugs, and possibly their bioequivalence to other inhaled products. Correlating drug product attributes to lung deposited dose is important to achieving equivalence. PUR0200 is a spray-dried formulation of tiotropium that enables more efficient lung delivery than Spiriva® HandiHaler® (HH). The ratio of tiotropium lung-to-oral deposition in PUR0200 was varied to investigate the impact of particle size on tiotropium pharmacokinetics, and the contribution of oral absorption to tiotropium exposure was assessed using charcoal block. METHODS: A seven-period, single-dose, crossover study was performed in healthy subjects. PUR0200 formulations differing in dose and aerodynamic particle size were administered in five periods and Spiriva HH in two periods. In one period, Spiriva HH gastrointestinal absorption was blocked with oral charcoal. Tiotropium plasma concentrations were assessed over 8 h after inhalation. RESULTS: PUR0200 pharmacokinetics were influenced by aerodynamic particle size and the ratio of lung-to-oral deposition, with impactor sized mass (ISM) correlating most strongly with exposure. Formulation PUR0217a (3 µg tiotropium) lung deposition was similar to Spiriva HH (18 µg) with and without charcoal block, but total PUR0200 exposure was lower without charcoal. The Cmax and AUC0-0.5h of Spiriva HH with and without charcoal block were bioequivalent; however, Spiriva HH AUC0-8h was lower when gastrointestinal absorption was inhibited with oral charcoal administration. CONCLUSIONS: Pharmacokinetic bioequivalence indicative of lung deposition and efficacy can be achieved by matching the reference product ISM. Due to reduced oral deposition and more efficient lung delivery, PUR0200 results in a lower AUC0-t than Spiriva HH due to reduced absorption of drug from the gastrointestinal tract.

Inhaled salbutamol from aerolizer and diskus at different inhalation flows, inhalation volume and number of inhalations in both healthy subjects and COPD patients.

The aim of the present study was to demonstrate the effect of inhalation-flow, inhalation-volume and number of inhalations on aerosol-delivery of inhaled-salbutamol from two different dry powder inhalers (DPIs) in both healthy-subjects and chronic obstructive pulmonary disease (COPD) patients. Relative pulmonary-bioavailability and systemic-bioavailability of inhaled-salbutamol, delivered by Diskus and Aerolizer, was determined in 24-COPD patients and 24-healthy subjects. The healthy-subjects and the COPD-patients participated in the study for 7 days in which they received 4 study doses of 200 µg salbutamol (one slow-inhalation, two slow-inhalations, one fast-inhalation, and two fast-inhalations) in four alternative days with 24 hr washout period after each dose. Two urine-samples were collected from each study subjects. The first was provided 30 min post inhalation (USAL0.5), as an index of relative pulmonary-bioavailability, and the second was pooled to 24 hr post inhalation (USAL24), as an index of systemic-bioavailability. Fast-inhalation resulted in significantly higher USAL0.5 and USAL24 than slow-inhalation (p˂0.05) after one-inhalation in both healthy-subjects and COPD-patients but there was no significant difference between slow and fast-inhalation after two-inhalations. One-inhalation resulted in significantly higher USAL0.5 and USAL24 in healthy-subjects compared to COPD-patient at both slow and fast-inhalation (p˂0.05) except USAL0.5 with Diskus at slow-inhalation there was no significant difference. Also, two-inhalations resulted in significantly higher USAL0.5 and USAL24 compared to one-inhalation at slow-inhalation only (p˂0.05). No significant difference was found between Aerolizer and Diskus except in USAL0.5 of one slow-inhalation in both health-subjects and COPD-patients (p = 0.048 and 0.047, respectively). Device-formula relation is present at low inhalation-flow since Diskus resulted in significantly higher USAL0.5 and USAL24 in healthy-subjects compared to COPD-patient at slow inhalation than Aerolizer. It is essential to inhale-twice and as hard and deep as possible from each dose when using DPI especially with COPD-patients having poor inspiratory efforts such as elderly patients and children.

Bioequivalence of fluticasone propionate and salmeterol (FS) given by the FS Spiromax® and Seretide Accuhaler® systems
.

OBJECTIVE: To determine pharmacokinetic (PK) profiles of fluticasone propionate (FP) and salmeterol (SAL) in healthy volunteers following administration as two inhalations from the FS Spiromax 500/50 µg and Seretide Accuhaler 50/500 µg inhalers, without (study 1, n = 79) and with charcoal block (study 2, n = 77). Safety was also assessed. MATERIALS AND METHODS: In two single-center, open-label, randomized two-period crossover studies, PK parameters were calculated from plasma drug concentrations obtained pre-dose through 36 hours post-dose. Bioequivalence was established if the 90% confidence intervals for the geometric mean ratios of the area under the plasma drug concentration-time curve from time zero to the time of the last quantifiable concentration (AUC0-t) and the maximum observed plasma concentration (Cmax) for the comparison of both FP and SAL were within 0.80 - 1.25. RESULTS: In study 1, in subjects administered FS Spiromax, the mean (standard deviation (SD)) FP AUC0-t and Cmax were 1,622.64 (419.44) pg×h/mL and 151.36 (40.37) pg/mL, respectively, vs. 1,487.52 (341.25) pg×h/mL and 137.57 (33.64) pg/mL with Seretide Accuhaler. Mean (SD) SAL AUC0-t and Cmax with FS Spiromax were 408.42 (155.40) pg×h/mL and 269.48 (105.74) pg/mL, respectively, vs. 401.79 (125.32) pg×h/mL and 265.66 (87.28) pg/mL with Seretide Accuhaler. Comparable data were seen in study 2 with charcoal block. Bioequivalence of FS Spiromax with Seretide Accuhaler was observed both without and with charcoal block for FP and SAL for both AUC0-t and Cmax. Both study treatments were well tolerated, with a similar incidence of adverse events reported with the single use of FS Spiromax (23% study 1, 16% study 2) and Seretide Accuhaler (22%, 15%). CONCLUSION: FS Spiromax 500/50 µg (± charcoal block) was bioequivalent to Seretide Accuhaler 50/500µg.
.

Pharmacokinetics of a modified, compounded theophylline product in dogs.

Theophylline is a commonly used bronchodilator drug for treatment of chronic canine bronchitis, but no formulations validated in dogs are currently available. An oral, modified and compounded theophylline product (MCT), which could fulfil this need, is available through a USP-compliant, veterinary compounding pharmacy; however, its pharmacokinetic properties are unknown. The aim of this study was to determine the pharmacokinetics of MCT. Plasma drug concentrations were measured in seven healthy, fed dogs after single doses of intravenous aminophylline (8.6 mg/kg theophylline equivalent) and oral MCT (10 mg/kg). Systemic bioavailability of the MCT was 96.2 ± 32.9%. MCT times to maximum concentration, mean absorption time and terminal half-life were 8.85 ± 3.63, 6.95 ± 3.42, and 8.67 ± 1.62 hr, respectively. Based on simulations of 10 mg/kg and 12-hr dosing, steady-state plasma theophylline concentrations are expected to exceed the minimum therapeutic concentration for 71.7 ± 35.6% of the dosing interval. Overall, the MCT product investigated showed similar pharmacokinetic characteristics compared to previously validated extended-release theophylline products. An oral dose of 10 mg/kg q 12 hr is likely an appropriate dosage to begin therapy; however, therapeutic drug monitoring may be warranted because of inter-individual variation.

Effect of Roughness on the Dispersion of Dry Powders for Inhalation: a Dynamic Visualization Perspective.

Dry powder inhalers have attracted more interest over the years in every aspect related to them. Interestingly, when focusing on the effects of particle morphology of the active or carrier (excipient), it is generally regarded particle size and shape to influence drug availability of aerosolized particles. However, to date, few studies have examined the effect of texture, i.e., roughness, on this relationship. The main objective of the present work is to gain a closer understanding of the influence of carrier morphology on the aerosolization performance of dry powder inhaler formulations. Image analysis and microscopy were used to visualize the aerosolization process. It is considered that the scale of morphological features on the surface of the carrier particles is responsible for the dispersion of the powder formulation, separation of the drug/carrier, and entrainment from a dry powder inhaler. Thus, for this study, the carrier particles of different surface roughness were mixed with micronized salbutamol sulphate. Aerosolization in vitro testing was used to evaluate the performance. The results indicate a connection between the qualitative surface roughness of coarse carriers and aerosolization performance during powder dispersibility. This investigation demonstrated that indeed, powder dispersion, a dynamic process, is influenced by the scale of the carrier morphology.

Effect of USP Induction Ports, Glass Sampling Apparatus, and Inhaler Device Resistance on Aerodynamic Patterns of Fluticasone Propionate-Loaded Engineered Mannitol Microparticles.

The present investigation is to study the effect of two different induction ports (IP), i.e., USP IP and USP-modified IP equipped with andersen cascade impactor on in vitro aerodynamic performance along with the impact of USP-modified glass sampling apparatus on delivered dose uniformity of fluticasone propionate (FP) dry powder inhaler (DPI). FP DPI was fabricated by spray drying technique using engineered mannitol microparticles (EMP) with different force controlling agents, i.e., leucine and magnesium stearate. Additionally, commercially available two DPI inhaler devices namely Handihaler® and Breezhaler® were used to aerosolize the FP blends. Spherical smooth surface of EMP showed good powder flow properties and acceptable percentage content uniformity (> 95%). Amounts of FP deposited in cascade assembly using USP-modified IP with the Breezhaler® device was significantly higher (1.32-fold) as compared with the Handihaler® device. Moreover, USP-modified IP showed better deposition as compared with USP IP. Additionally, both inhaler devices showed a satisfactory delivered dose (> 105%) for FP using modified glass sampling apparatus at a flow rate of 60 L/min for 2 s. It was interesting to note that not only formulation properties but also IP geometry and device resistance have significant impact on DPI deposition pattern. This study is a first detailed account of aerodynamic performance of FP using USP-modified IP and USP-modified glass sampling apparatus. Thus, it can be of potential importance for both the academic and industry perspective.

Ion-Pairing with Spermine Targets Theophylline To the Lungs via the Polyamine Transport System.

Certain xenobiotics, such as paraquat, are sequestered into the lungs from the systemic circulation by the polyamine transporter system (PTS). The aim of this study was to investigate whether ion-pairing a drug (theophylline) with a PTS substrate (spermine) provides a means of using this active transport mechanism to target drug delivery to the lungs. Fourier transform infrared spectroscopy showed that two of the amine groups of spermine interact with C-N7 and C6═O of theophylline, leaving two free amines to interact with the PTS. In A549 cells, which possess a functional PTS (spermidine Km and Vmax, 0.6 ± 0.3 µM and 1.8 ± 0.3 pmol·min-1 per 105 cells, respectively), uptake of the theophylline-spermine ion-pair was increased 1.8-fold compared to free theophylline at 37 °C, but not at 4 °C. In an isolated perfused rat lung model (IPL) a 3.6-fold increase in lung theophylline concentration was observed after vascular administration of the ion-pair compared to free theophylline. Theophylline was cleared from the IPL with similar kinetics irrespective of whether it was delivered as the free drug or an ion-pair, although lung levels remained elevated after washout following delivery as an ion-pair. In vitro simulation of the theophylline-spermine break down demonstrated that a drop in pH from 9.6 to 7.4, such as that undergone by the ion-pair in biological matrices, induces rapid and almost complete dissociation of the ion-paired species. However, infusion of the ion-pair formulations via the vasculature provides almost immediate delivery to the pulmonary capillary bed permitting PTS-mediated active sequestering of ion-paired theophylline into the lungs.

Size distribution of salbutamol/ipratropium aerosols produced by different nebulizers in the absence and presence of heat and humidification.

BACKGROUND: Few studies have evaluated the size distribution of inhaled and exhaled aerosolized drugs, or the effect of heated humidification on particle size and lung deposition. The present study evaluated these aspects of bronchodilator (salbutamol/ipratropium) delivery using a lung model in the absence and presence of heat and humidification. METHODS: We positioned filters to collect and measure the initial drug, inhaled drug, and exhaled drug. Particle size distribution was evaluated using an 8-stage Marple personal cascade impactor with 0.2-µm polycarbonate filters. RESULTS: A greater inhaled drug mass was delivered using a vibrating mesh nebulizer (VMN) than by using a small volume nebulizer (SVN), when heated humidifiers were not employed. When heated and humidified medical gas was used, there was no significant difference between the inhaled drug mass delivered by the VMN and that delivered by the SVN. A significantly greater mass of inhaled 1.55-µm drug particles was produced by the VMN than with the SVN, under heated and humidified conditions. However, the mass median aerodynamic diameters (MMADs) of the aerosolized drug produced by the SVN and VMN did not differ significantly under the same conditions. CONCLUSIONS: The VMN produced more fine particles of salbutamol/ipratropium, and the drug particle size clearly increased in the presence of heat and humidification.

Pharmacokinetics and safety of a single dose of the novel LAMA/LABA fixed-dose combination of glycopyrronium/formoterol fumarate dihydrate metered dose inhaler, formulated using co-suspension delivery technology, in Japanese healthy subjects.

BACKGROUND: Chronic obstructive pulmonary disease (COPD) causes significant mortality in Japan. GFF MDI is a long-acting muscarinic antagonist/long-acting ß2-agonist fixed-dose combination of glycopyrronium (GP) and formoterol fumarate dihydrate (FF), delivered by a metered dose inhaler (MDI) using co-suspension delivery technology, for the long-term maintenance treatment of COPD. METHODS: This randomized, Phase I, single-dose, four-treatment, four-period, crossover study (NCT02196714) examined the pharmacokinetic (PK) and safety profile of two doses of GFF MDI (28.8 µg/10 µg and 14.4 µg/10 µg) and two doses of GP MDI (28.8 µg and 14.4 µg), both formulated using co-suspension delivery technology, in healthy Japanese subjects (18-45 years of age). PK parameters included area under the curve (AUC) from 0 to 12 h (AUC0-12), AUC from 0 to the time of the last measurable plasma concentration, maximum observed plasma concentration (Cmax), and time to Cmax. Safety was monitored throughout the study. RESULTS: Plasma GP profiles were comparable between GFF MDI and GP MDI formulations containing the same GP dose. Increases in GP AUC0-12 and Cmax were generally dose proportional from 14.4 to 28.8 µg after administration of either formulation. CONCLUSIONS: The addition of FF 10 µg to GP MDI 28.8 µg or 14.4 µg in a fixed-dose combination did not appreciably alter the PK of GP, nor did an increase in GP dose from 14.4 µg to 28.8 µg in a fixed-dose combination with FF 10 µg appreciably alter the PK of formoterol. Both formulations of GFF MDI and GP MDI were well tolerated in healthy Japanese subjects. Data from this study support further evaluation of GFF MDI in Japanese patients with COPD.

The pharmacokinetics of three doses of budesonide/glycopyrronium/formoterol fumarate dihydrate metered dose inhaler compared with active controls: A Phase I randomized, single-dose, crossover study in healthy adults.

The budesonide/glycopyrronium/formoterol fumarate dihydrate metered dose inhaler (BGF MDI) is an inhaled corticosteroid/long-acting muscarinic antagonist/long-acting ß2-agonist fixed-dose combination formulated with innovative co-suspension delivery technology that is in clinical development for the treatment of chronic obstructive pulmonary disease (COPD). This randomized, Phase I, single-dose, six-treatment, four-period, crossover study (NCT01980615) examined the pharmacokinetic (PK) and safety profile of three doses of BGF MDI (320/14.4/10 µg [equivalent to budesonide/glycopyrrolate/formoterol fumarate 320/18/9.6 µg], 160/14.4/10 µg and 80/14.4/10 µg), two doses of a budesonide/formoterol fumarate dihydrate fixed-dose combination (BUD/FORM MDI 320/9 µg and 160/9 µg; not using co-suspension delivery technology) and a glycopyrronium/formoterol fumarate dihydrate co-suspension delivery technology MDI (GFF MDI 14.4/10 µg) in healthy volunteers (18-45 years of age). PK parameters included area under the plasma concentration-time curve from 0 to 12 h (AUC0-12), AUC up to the last measurable concentration (AUC0-t), maximum plasma concentration (Cmax) and time to maximum plasma concentration (tmax). Safety was monitored throughout the study. Of 84 subjects randomized, 76 completed the study. BGF MDI 320/14.4/10 µg was bioequivalent to BUD/FORM MDI 320/9 µg for budesonide for Cmax, AUC0-12 and AUC0-t (primary objective). Dose proportionality was observed for the budesonide component between BGF MDI 80/14.4/10 µg and BGF MDI 160/14.4/10 µg, and between BGF MDI 160/14.4/10 µg and BGF MDI 320/14.4/10 µg. Systemic exposure to glycopyrronium and formoterol after BGF MDI 320/14.4/10 µg treatment was similar to GFF MDI 14.4/10 µg. The rate of adverse events was 3.7-17.9% across treatments without any serious adverse events. In conclusion, BGF MDI 320/14.4/10 µg had a similar budesonide PK profile to BUD/FORM MDI 320/9 µg. No PK drug-drug interactions were observed when budesonide was added to glycopyrronium and formoterol fumarate dihydrate. These data support the use of budesonide 320 µg and 160 µg in future clinical trials of BGF MDI in COPD.