Structural and excitonic properties of the polycrystalline FAPbI3thin films, and their photovoltaic responses.

Faormamadinium based perovskites have been proposed to replace the methylammonium lead tri-iodide (MAPbI3) perovskite as the light absorbing layer of photovoltaic cells owing to their photo-active and chemically stable properties. However, the crystal phase transition from the photo-activeα-FAPbI3to the non-perovksiteδ-FAPbI3still occurs in un-doped FAPbI3films owing to the existence of crack defects, which degrads the photovoltaic responses. To investigate the crack ratio (CR)-dependent structure and excitonic characteristics of the polycrystalline FAPbI3thin films deposited on the carboxylic acid functionalized ITO/glass substrates, various spectra and images were measured and analyzed, which can be utilized to make sense of the different devices responses of the resultant perovskite based photovoltaic cells. Our experimental results show that the there is a trade-off between the formations of surface defects and trapped iodide-mediated defects, thereby resulting in an optimal crack density or CR of the un-dopedα-FAPbI3active layer in the range from 4.86% to 9.27%. The decrease in the CR (tensile stress) results in the compressive lattice and thereby trapping the iodides near the PbI6octahedra in the bottom region of the FAPbI3perovskite films. When the CR of the FAPbI3film is 8.47%, the open-circuit voltage (short-circuit current density) of the resultant photovoltaic cells significantly increased from 0.773 V (16.62 mA cm-2) to 0.945 V (18.20 mA cm-2) after 3 d. Our findings help understanding the photovoltaic responses of the FAPbI3perovskite based photovoltaic cells on the different days.

Effects of bendable P3CT polymers layer on the photovoltaic performance of perovskite solar cells.

We report on the formation of bendable and edge-on poly[3-(4-carboxybutyl)thiophene-2,5-diyl] (P3CT) polymers thin layer used as a hole modification layer (HML) in the inverted perovskite solar cell. The aggregations of 2D layer-like P3CT polymers in dimethylformamide (DMF) solution can be formed via aromaticπ-πstacking interactions and/or hydrogen-bonding interactions with the different concentration from 0.01 to 0.02 wt%, which highly influences the photovoltaic performance of the inverted perovskite solar cells. The atomic-force microscopic images and water droplet contact angle images show that the P3CT polymers modify the surface properties of the transparent conductive substrate and thereby dominating the formation of perovskite crystalline thin films, which play important roles in the highly efficient and stable perovskite solar cells. It is noted that theVOC(JSC) of the encapsulated solar cells values are maintained to be higher than 1.115 V (22 mA cm-2) after 104 d when an optimizedπ-πstacked and hydrogen-bonded P3CT polymer is used as the HML. On the other hand, the solar cell showed a high long-term stability by maintaining 85% of the initial power conversion efficiency in the ambient air for 103 d.

Dislocation characterization inc-plane GaN epitaxial layers on 6 inch Si wafer with a fast second-harmonic generation intensity mapping technique.

Second harmonic generation (SHG) intensity, Raman scattering stress, photoluminescence and reflected interference pattern are used to determine the distributions of threading dislocations (TDs) and horizontal dislocations (HDs) in thec-plane GaN epitaxial layers on 6 inch Si wafer which is a structure of high electron mobility transistor (HEMT). The Raman scattering spectra show that the TD and HD result in the tensile stress and compressive stress in the GaN epitaxial layers, respectively. Besides, the SHG intensity is confirmed that to be proportional to the stress value of GaN epitaxial layers, which explains the spatial distribution of SHG intensity for the first time. It is noted that the dislocation-mediated SHG intensity mapping image of the GaN epitaxial layers on 6 inch Si wafer can be obtained within 2 h, which can be used in the optimization of high-performance GaN based HEMTs.

Editorial for focus on manipulations of atomic and molecular layers and its applications in energy, environment sciences and optoelectronic devices.

This Focus aims at showcasing the significance of manipulating atomic and molecular layers for various applications. To this end, this Focus collects 15 original research papers featuring the applications of atomic layer deposition, chemical vapor deposition, wet chemistry, and some other methods for manipulations of atomic and molecular layers in lithium-ion batteries, supercapacitors, catalysis, field-effect transistors, optoelectronics, and others.

Multiple Nucleocapsid Structural Forms of Shrimp White Spot Syndrome Virus Suggests a Novel Viral Morphogenetic Pathway.

White spot syndrome virus (WSSV) is a very large dsDNA virus. The accepted shape of the WSSV virion has been as ellipsoidal, with a tail-like extension. However, due to the scarcity of reliable references, the pathogenesis and morphogenesis of WSSV are not well understood. Here, we used transmission electron microscopy (TEM) and cryogenic electron microscopy (Cryo-EM) to address some knowledge gaps. We concluded that mature WSSV virions with a stout oval-like shape do not have tail-like extensions. Furthermore, there were two distinct ends in WSSV nucleocapsids: a portal cap and a closed base. A C14 symmetric structure of the WSSV nucleocapsid was also proposed, according to our Cryo-EM map. Immunoelectron microscopy (IEM) revealed that VP664 proteins, the main components of the 14 assembly units, form a ring-like architecture. Moreover, WSSV nucleocapsids were also observed to undergo unique helical dissociation. Based on these new results, we propose a novel morphogenetic pathway of WSSV.

Improving the photovoltaic performance of inverted perovskite solar cells via manipulating the molecular packing structure of PCBM.

In this study, the molecular packing structure of solution-processed phenyl-C61-butyric acid methyl ester (PCBM) thin film was manipulated by varying the volume ratio of chlorobenzene (CB) to bromobenzene (BrB) from 100:0 to 50:50, which largely influences the device performance of the PCBM/perovskite heterojunction solar cells. Absorbance spectra, photoluminescence spectra, atomic force microscopic images and contact angle images were used to investigate the molecular packing structure effects of the PCBM thin films on the device performance of the inverted perovskite solar cells. Our experimental results show that the formation of PCBM aggregates and the contact quality at the PCBM/perovksite interface significantly influence the open-circuit voltage, short-circuit current density and fill factor of the resultant solar cells simultaneously. It is noted that the PCE of the encapsulated inverted CH3NH3PbI3(MAPbI3) solar cells exhibited a stable and high power conversion efficiency of 18%.

Improving device performance of MAPbI3photovoltaic cells by manipulating the crystal orientation of tetragonal perovskites.

The properties of CH3NH3PbI3(MAPbI3) crystalline thin films and the device performance of highly efficient MAPbI3photovoltaic cells are investigated by varying the temperature of the antisolvent from 20 °C to 50 °C during the washing enhanced nucleation (WEN) process. The surface, structural, optoelectronic and defect properties of the perovskite thin films are characterized through atomic-force microscopy, X-ray diffractometry and photoluminescence spectrometry. The experimental results show that changing the temperature of the antisolvent during the WEN process can manipulate the MAPbI3crystalline thin films from the (110)-(002) complex phase to a (002) preferred phase. It is noted that the highest power conversion efficient of the inverted MAPbI3photovoltaic cells is 19.30%, mainly due to the increased carrier collection efficiency and reduced carrier recombination when the temperature of the antisolvent is 30 °C.

Efficiency improvement of P3CT-Na based MAPbI3solar cells with a simple wetting process.

The averaged power conversion efficiency of polyelectrolytes (P3CT-Na) based MAPbI3solar cells can be increased from 14.94% to 17.46% with a wetting method before the spin-coating process of MAPbI3precursor solutions. The effects of the wetting process on the surface, structural, optical and excitonic properties of MAPbI3thin films are investigated by using the atomic-force microscopic images, x-ray diffraction patterns, transmittance spectra, photoluminescence spectra and Raman scattering spectra. The experimental results show that the wetting process of MAPbI3precursor solution on top of the P3CT-Na/ITO/glass substrate can be used to manipulate the molecular packing structure of the P3CT-Na thin film, which determines the formation of MAPbI3thin films.

Improvement of interfacial contact for efficient PCBM/MAPbI3planar heterojunction solar cells with a binary antisolvent mixture treatment.

Atomic-force microscopic images, x-ray diffraction patterns, Urbach energies and photoluminescence quenching experiments show that the interfacial contact quality between the hydrophobic [6,6]-phenyl-C61-buttric acid methyl ester (PCBM) thin film and hydrophilic CH3NH3PbI3(MAPbI3) thin film can be effectively improved by using a binary antisolvent mixture (toluene:dichloromethane or chlorobenzene:dichloromethane) in the anti-solvent mixture-mediated nucleation process, which increases the averaged power conversion efficiency of the resultant PEDOT:PSS (P3CT-Na) thin film based MAPbI3solar cells from 13.18% (18.52%) to 13.80% (19.55%). Beside, the use of 10% dichloromethane (DCM) in the binary antisolvent mixture results in a nano-textured MAPbI3thin film with multicrystalline micrometer-sized grains and thereby increasing the short-circuit current density and fill factor (FF) of the resultant solar cells. It is noted that a remarkable FF of 80.33% is achieved, which can be used to explain the stable photovoltaic performance without additional encapsulations.

Aggregation-induced negative differential resistance in graphene oxide quantum dots.

Negative differential resistance (NDR) devices have attracted considerable interest due to their potential applications in switches, memory devices, and analog-to-digital converters. Modulation of the NDR is an essential issue for the development of NDR-based devices. In this study, we successfully synthesized graphene oxide quantum dots (GOQDs) using graphene oxide, cysteine, and H2O2. The current-voltage characteristics of the GOQDs exhibit a clear NDR in the ambient environment at room temperature. A peak-to-valley ratio as high as 4.7 has been achieved under an applied voltage sweep from -6 to 6 V. The behavior of the NDR and its corresponding peak-to-valley ratio can be controlled by adjusting the range of applied voltages, air pressure, and relative humidity. Also, the NDR is sensitive to the the concentration of H2O2 added in the synthesis. The charge carrier injection through the trapping states, induced by the GOQD aggregation, could be responsible for the NDR behavior in GOQDs.

Origins of the s-shape characteristic in J-V curve of inverted-type perovskite solar cells.

Fullerene derivative thin films have been widely used in inverted-type perovskite solar cells as the electron transport layer (ETL) and hole blocking layer. However, the smooth contact at the interface between the hydrophobic [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) and hydrophilic CH3NH3PbI3 (MAPbI3) thin film has not yet been completely understood. The contact at the PCBM/MAPbI3 interface strongly influences the photovoltaic performance. The photovoltaic devices were characterized by measuring the light intensity-dependent current density-voltage (J-V) curves and impedance spectra, which show that the contact at the PCBM/MAPbI3 interface simultaneously influences the shunt resistance (carrier recombination) and series resistance (interfacial contact). In addition, x-ray diffraction patterns, atomic force microscopic images, absorbance spectra and photoluminescence spectra were used to explore the contact at the PCBM/MAPbI3 interface. The experimental results show that the flat MAPbI3 thin film cannot be completely covered by a PCBM thin film and thereby results in the s-shape characteristic in the J-V curve of the resultant solar cells. The s-shaped J-V curve can be suppressed by increasing the crystallinity and surface roughness of the MAPbI3 thin film. With the use of an interface modification layer in between the PCBM thin film and Ag cathode, the power conversion efficiency of MAPbI3 solar cells can be increased from 10.50% to 13.71%.

Enhancement of photocurrent extraction and electron injection in dual-functional CH3NH3PbBr3 perovskite-based optoelectronic devices via interfacial engineering.

Photocurrent extraction and electron injection in CH3NH3PbBr3 (MAPbBr3) perovskite-based optoelectronic devices are both significantly increased by improving the contact at the PCBM/MAPbBr3 interface with an extended solvent annealing (ESA) process. Photoluminescence quenching and x-ray diffraction experiments show that the ESA not only improves the contact at the PCBM/MAPbBr3 interface but also increases the crystallinity of the MAPbBr3 thin films. The optimized dual-functional PCBM-MAPbBr3 heterojunction based optoelectronic device has a high power conversion efficiency of 4.08% and a bright visible luminescence of 1509 cd m-2. In addition, the modulation speed of the MAPbBr3 based light-emitting diodes is larger than 14 MHz, which indicates that the defect density in the MAPbBr3 thin film can be effectively reduced by using the ESA process.

Functional graded fullerene derivatives for improving the fill factor and device stability of inverted-type perovskite solar cells.

A graded fullerene derivative thin film was used as a dual-functional electron transport layer (ETL) in CH3NH3PbI3 (MAPbI3) solar cells, to improve the fill factor (FF) and device stability. The graded ETL was made by mixing phenyl-C61-butyric acid methyl ester (PCBM) molecules and C60-diphenylmethanofullerene-oligoether (C60-DPM-OE) molecules using the spin-coating method. The formation of the graded ETLs can be due to the phase separation between hydrophobic PCBM and hydrophilic C60-DPM-OE, which was confirmed by XPS depth-profile analysis and an electron energy-loss spectroscope. Comprehensive studies were carried out to explore the characteristics of the graded ETLs in MAPbI3 solar cells, including the surface properties, electronic energy levels, molecular packing properties and energy transfer dynamics. The elimination of the s-shape in the current density-voltage curves results in an increase in the FF, which originates from the smooth contact between the C60-DPM-OE and hydrophilic MAPbI3 and the formation of the more ordered ETL. There was an improvement in device stability mainly due to the decrease in the photothermal induced morphology change of the graded ETLs fabricated from two fullerene derivatives with distinct hydrophilicity. Consequently, such a graded ETL provides dual-functional capabilities for the realization of stable high-performance MAPbI3 solar cells.

Genetic Polymorphisms of Alcohol Metabolizing Enzymes and Alcohol Consumption are Associated With Asymptomatic Cardiac Remodeling and Subclinical Systolic Dysfunction in Large Community-Dwelling Asians.

AIMS: Excessive consumption of alcoholic beverages is associated with cardiac remodeling and cardiomyopathy. We examined the possible association of alcohol use, common Asian genetic variants in genes involved in alcohol metabolism, and cardiac structures/functions alterations. METHODS: A prospective, community-dwelling survey among individuals with available complete echocardiography examined the associations of alcohol use, cardiac structure/functions, and three common alcohol metabolizing genetic variants, including aldehyde dehydrogenase 2 (ALDH2), alcohol dehydrogenase 1B (ADH1B) and cytochrome P450 (CYP) isoform 2E1 (CYP2E1). RESULTS: Among 1577 participants (mean age: 53 ± 9, 59.7% female), we observed that in subjects with more frequent weekly ethanol intake showed greater left ventricle (LV) mass, more impaired diastolic functions, and reduced global longitudinal strain (GLS), systolic (SRs) and early diastolic strain rates (SRe) (P<0.05). After propensity matching for clinical confounders (n = 330:30 for frequent users and non-users), frequent alcohol use and subjects carrying ALDH2 (A/G or A/A), ADH1B (A/A) or CYP2E1(T/C or T/T) polymorphisms were all associated with worse GLSRs and GLSRe, with combined alcohol use and any given genetic variant aggravated these associations (all P < 0.05). Finally, we observed Gene-Gene synergistic effects on LV functional decline in frequent alcohol users by using linear mixed effect model (all interaction P < 0.05). CONCLUSIONS: Among East Asians, even moderate alcohol consumption can confer subclinical adverse effects on cardiac systolic functions, which was most pronounced in subjects carrying common variants in alcohol metabolizing genes. These findings challenge the notion of beneficial influences of less heavy ethanol consumption on the heart, especially among East Asians. SHORT SUMMARY: This study evaluated the association of level of alcohol consumption and genetic variants in genes involved in alcohol metabolism with changes in cardiac function in East Asians. Even moderate alcohol use conferred subclinical adverse effects on cardiac systolic functions, which were most pronounced in subjects carrying common alcohol metabolizing genes.

Changes of Atrial Natriuretic Peptides after Defibrillation Threshold Testing Predicted Future Ventricular Arrhythmia Event.

BACKGROUND: We investigated the change of natriuretic peptides during defibrillation threshold (DFT) testing and its relationship with future ventricular arrhythmia (VA) events in patients implanted with an implantable cardioverter defibrillator (ICD). METHODS: Atrial natriuretic peptide (ANP), brain natriuretic peptide (BNP), and c-type natriuretic peptide (CNP) were measured in 21 patients (mean age 61 ± 13 years; 67% male) undergoing ICD implantation. Blood samples of the patients were drawn at pre-implantation, 30 minutes, 60 minutes, and 24 hours after DFT testing. The patients were followed and divided into two groups according to the occurrence of VA in 18 months. The biomarker levels and their changes were compared in patients with and without further VA. RESULTS: The pre-implantation ANP levels were higher at pre-implantation and increased significantly at 30 minutes after DFT testing (Δ30minANP) among patients with VA events. The BNP and CNP levels did not change significantly after DFT testing in both groups. The area under curve was 0.82 for the change in Δ30minANP determining further ventricular events. The optimal Δ30minANP cutoff value was 0.51 pg/ml, with sensitivity of 0.83 and specificity of 0.68. Multivariable analysis confirmed that patients with Δ30minANP more than 0.51 pg/ml have a higher risk of further ventricular events (hazard ratio 39.8, 95% confidence interval: 2.87-553.01, p = 0.006). The pre-implantation ANP level could not predict future VA events (hazard ratio 1.06, 95% CI: 1.00-1.14, p = 0.06). CONCLUSIONS: The increase of ANP concentration after DFT testing predicted future VA events after ICD implantation while the BNP and CNP levels did not predict future VA events.

Responses of cardiac natriuretic peptides after paroxysmal supraventricular tachycardia: ANP surges faster than BNP and CNP.

Atrial natriuretic peptide (ANP) secretion increases after 30 min of paroxysmal supraventricular tachycardia (PSVT). Whether this phenomenon also applies to brain or C-type natriuretic peptides (BNP or CNP) remains unknown. Blood samples of 18 patients (41 ± 11 yr old; 4 men) with symptomatic PSVT and normal left ventricular systolic function (ejection fraction 65 ± 6%) were collected from the coronary sinus (CS) and the femoral artery (FA) before and 30 min after the induction, and 30 min after the termination of PSVT. The results showed that the ANP levels rose steeply after the PSVT and then reduced at 30 min after the termination (baseline vs. post-PSVT vs. posttermination: CS: 34.0 ± 29.6 vs. 74.1 ± 42.3 vs. 46.1 ± 32.9; FA: 5.9 ± 3.24 vs. 28.2 ± 20.7 vs. 10.0 ± 4.6 pg/ml; all P < 0.05). In contrast, compared with ANP, the increases of BNP and CNP in CS after the PSVT were less sharp, but continued to rise after the termination of tachycardia (BNP, 10.2 ± 6.4 vs. 11.3 ± 7.1 vs. 11.8 ± 7.9; CNP, 4.5 ± 1.2 vs. 4.9 ± 1.4 vs. 5.0 ± 1.4 pg/ml; all P < 0.05). The rise of BNP and CNP in FA was similarly less sharp after the PSVT and remained stationary after the termination. PSVT exerted differential effects on cardiac natriuretic peptide levels. ANP increased greater after a 30-min induced PSVT, but dropped faster after termination of PSVT, compared with BNP and CNP.

Metal-free tetrathienoacene sensitizers for high-performance dye-sensitized solar cells.

A new series of metal-free organic chromophores (TPA-TTAR-A (1), TPA-T-TTAR-A (2), TPA-TTAR-T-A (3), and TPA-T-TTAR-T-A (4)) are synthesized for application in dye-sensitized solar cells (DSSC) based on a donor-π-bridge-acceptor (D-π-A) design. Here a simple triphenylamine (TPA) moiety serves as the electron donor, a cyanoacrylic acid as the electron acceptor and anchoring group, and a novel tetrathienoacene (TTA) as the π-bridge unit. Because of the extensively conjugated TTA π-bridge, these dyes exhibit high extinction coefficients (4.5-5.2 × 10(4) M(-1) cm(-1)). By strategically inserting a thiophene spacer on the donor or acceptor side of the molecules, the electronic structures of these TTA-based dyes can be readily tuned. Furthermore, addition of a thiophene spacer has a significant influence on the dye orientation and self-assembly modality on TiO2 surfaces. The insertion of a thiophene between the π-bridge and the cyanoacrylic acid anchoring group in TPA-TTAR-T-A (dye 3) promotes more vertical dye orientation and denser packing on TiO2 (molecular footprint = 79 Å(2)), thus enabling optimal dye loading. Using dye 3, a DSSC power conversion efficiency (PCE) of 10.1% with Voc = 0.833 V, Jsc = 16.5 mA/cm(2), and FF = 70.0% is achieved, among the highest reported to date for metal-free organic DSSC sensitizers using an I(-)/I3(-) redox shuttle. Photophysical measurements on dye-grafted TiO2 films reveal that the additional thiophene unit in dye 3 enhances the electron injection efficiency, in agreement with the high quantum efficiency.

Label-free multi-color superlocalization of plasmonic emission within metallic nano-interstice using femtosecond chirp-manipulated four wave mixing.

We demonstrate an as yet unused method to sieve, localize, and steer plasmonic hot spot within metallic nano-interstices close to percolation threshold. Multicolor superlocalization of plasmon mode within 60 nm was constantly achieved by chirp-manipulated superresolved four wave mixing (FWM) images. Since the percolated film is strongly plasmonic active and structurally multiscale invariant, the present method provides orders of magnitude enhanced light localization within single metallic nano-interstice, and can be universally applied to any region of the random film. The result, verified by the maximum likelihood estimation (MLE) and deconvolution stochastic optical reconstruction microscopy (deconSTORM) algorithm, may contribute to label-free multiplex superlocalized spectroscopy of single molecule and sub-cellular activity monitoring combining hot spot steering capability.

Pathogenesis of acute hepatopancreatic necrosis disease (AHPND) in shrimp.

Acute hepatopancreatic necrosis disease (AHPND), also called early mortality syndrome (EMS), is a recently emergent shrimp bacterial disease that has resulted in substantial economic losses since 2009. AHPND is known to be caused by strains of Vibrio parahaemolyticus that contain a unique virulence plasmid, but the pathology of the disease is still unclear. In this study, we show that AHPND-causing strains of V. parahaemolyticus secrete the plasmid-encoded binary toxin PirAB(vp) into the culture medium. We further determined that, after shrimp were challenged with AHPND-causing bacteria, the bacteria initially colonized the stomach, where they started to produce PirAB(vp) toxin. At the same early time point (6 hpi), PirB(vp) toxin, but not PirA(vp) toxin, was detected in the hepatopancreas, and the characteristic histopathological signs of AHPND, including sloughing of the epithelial cells of the hepatopancreatic tubules, were also seen. Although some previous studies have found that both components of the binary PirAB(vp) toxin are necessary to induce a toxic effect, our present results are consistent with other studies which have suggested that PirB(vp) alone may be sufficient to cause cellular damage. At later time points, the bacteria and PirA(vp) and PirB(vp) toxins were all detected in the hepatopancreas. We also show that Raman spectroscopy "Whole organism fingerprints" were unable to distinguish between AHPND-causing and non-AHPND causing strains. Lastly, by using minimum inhibitory concentrations, we found that both virulent and non-virulent V. parahaemolyticus strains were resistant to several antibiotics, suggesting that the use of antibiotics in shrimp culture should be more strictly regulated.

Plasmonic structure enhanced exciton generation at the interface between the perovskite absorber and copper nanoparticles.

The refractive index and extinction coefficient of a triiodide perovskite absorber (TPA) were obtained by fitting the transmittance spectra of TPA/PEDOT:PSS/ITO/glass using the transfer matrix method. Cu nanoplasmonic structures were designed to enhance the exciton generation in the TPA and to simultaneously reduce the film thickness of the TPA. Excitons were effectively generated at the interface between TPA and Cu nanoparticles, as observed through the 3D finite-difference time-domain method. The exciton distribution is advantageous for the exciton dissociation and carrier transport.